CLS300 Catalog Sheet

© Siemens AG 2016
Level Measurement
Point level measurement - RF Capacitance switches
Pointek CLS300 - Standard
■ Overview
■ Configuration
Installation
4
Pointek CLS300 (standard version) is an inverse frequency shift
capacitance level and material detection switch with optional
rod/cable choices and configurable output. CLS300 is ideal for
detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are
present and has the ability to tune out buildup on the probe.
Keep unit out of path of falling material, or protect probe from
falling material.
■ Benefits
• Active-Shield technology so measurement is unaffected by
material buildup or nozzle interference in active shield section
• Performs in extremely abrasive conditions because of solid
rod construction
• Three LED indicators for adjustment control, output status,
and power
• High-temperature version up to 400 °C (752 °F)
Build up of material in active shield area does not affect
switch operation.
■ Application
Pointek CLS300 standard version has three LED indicators with
basic relay and solid-state switch alarms.
M
The robust design of CLS300 makes it specifically applicable for
heavy solids applications where abrasive materials occur as in
the mining industry.
in
.5
0
Wetted parts are made of stainless steel with a PFA shield for
high chemical resistance, and of ceramic and stainless steel for
high temperature version. Materials with low or high dielectric
constants can be accurately detected. The unique Active Shield
suppresses interference from material buildup or long installation nozzles.
The unique modular design of the Pointek CLS300 provides a
wide range of configurations, process connections, extensions
and approvals to meet the temperature and pressure requirements of specific applications. The modular design makes ordering easier and reduces stocking requirements. A wide range
of probe configurations are available, including rod and cable
versions.
• Key Applications: liquids, slurries, bulk solids, relatively high
pressure and temperature, hazardous areas, milling and
mining applications
)
(2
The fully potted electronics are unaffected by condensation,
dust or vibration.
Min.
50 (2)
Install probe at least 50 (2) from tank wall.
Note angle of repose and adjust accordingly.
Pointek CLS300 installation, dimensions in mm (inch)
Siemens FI 01 · 2016
4/43
© Siemens AG 2016
Level Measurement
Point level measurement - RF Capacitance switches
Pointek CLS300 - Standard
■ Technical specifications
Design
Mode of operation
Measuring principle
Inverse frequency shift capacitive
level detection
Material (enclosure)
Powder-coated aluminum with gasket
Degree of Protection
Standard: Type 4/NEMA 4/IP65
Optional: Type 4/NEMA 4/IP68
Change in picoFarad (pF)
Cable inlet
2 x M20 x 1.5 thread
(option: 2 x ½" NPT conduit entry
including 1 plugged entry)
Input
Measured variable
Output
Output signal
• Relay output
- Max. contact voltage
- Max. contact current
- Max. switching capacity
4
- Time delay (ON and/or OFF)
• Solid-state output
- Output
- Protection
- Max. switching voltage
Controls and displays
1 SPDT Form C relay
• 30 V DC
• 250 V AC
• 5 A (DC)
• 8 A (AC)
• 150 W (DC)
• 2 000 VA (AC)
1 ... 60 s
3 LEDs, for probe status, output status and power supply
Potentiometers
2 potentiometers for time delay and
sensitivity
Switches
5 DIP switches for delay on/off, failsafe high/low, time delay test/adjust,
high/low sensitivity, test delay settings
Power supply
Galvanically isolated
Against reversed polarity (bipolar)
• 30 V (DC)
• 30 V peak (AC)
82 mA
- Max. load current
- Voltage drop
< 1 V, typical at 50 mA
- Time delay (pre or post switching) 1 ... 60 s
Accuracy
Resolution
• Min. sensitivity (pF)
• Max. temperature error
Displays
Supply
Certificates and approvals
General Purpose
CSA, FM, CE, RCM
Flameproof Enclosure with IS Probe
ATEX II 1/2 G EEx d[ia] IIC T6 ... T1
ATEX II 1/2 D T100 °C
Dust Ignition Proof with IS Probe
ATEX II 1/2 D T100 °C
CSA/FM Class II, Div. 1,
Groups E, F, G
CSA/FM Class III T4
Explosion Proof Enclosure with IS
Probe
CSA/FM Class I, Div. 1,
Groups A, B, C, D
CSA/FM Class II, Div. 1,
Groups E, F, G
CSA/FM Class III T4
1 % change in actual capacitance
0.2 % of actual capacitance value
Rated operating conditions1)
12 ... 250 V AC/DC, 0 ... 60 Hz,
galvanically isolated, 2 W
Installation conditions
• Location
Indoor/outdoor
Ambient conditions
• Ambient temperature
-40 ... +85 °C (-40 ... +185 °F)2)
Marine
Lloyds Register of Shipping,
Categories ENV1, ENV2, and ENV5
Liquids, bulk solids, slurries and interfaces, and applications with viscous
materials
Min. 1.5
Overfill Protection
WHG (Germany)
VLAREM II (Belgium)
Others
Pattern Approval (China)
Medium conditions
• Relative dielectric constant r
• Process temperature
- Rod/Cable version
- High-temperature version
• Process pressure3)
1)
-40 ... +200 °C (-40 ... +392 °F)2)
-40 ... +400 °C (-40 ... +752 °F)
-1 ... +35 bar g
(-14.6 ... +511 psi g)
When operation is in areas classified as hazardous, observe restrictions
according to relevant certificate. See also Pressure/Temperature curves
starting on page 4/57.
2) Thermal isolator is used if process connection temperature exceeds 85 °C
(185 °F).
3)
Pressure rating of process seal is temperature dependent. See Pressure/
Temperature curves starting on page 4/57.
Design: Probe
Rod version
High Temperature version
Cable version
Length
Min. 250 mm (9.8 inch),
max. 1 000 mm (40 inch)
Min. 250 mm (9.8 inch),
max. 1 000 mm (40 inch)
Min. 1 000 mm (40 inch),
max. 25 000 mm (984 inch)
Sensor wetted parts
PFA (no insulation on active probe),
316L stainless steel, PEEK isolators
Ceramic (ZrO21)) isolators (no insulation on active probe), 316L stainless
steel
316 stainless steel, optional PFA,
PEEK isolators
O-ring seal material
FKM (optional FFKM)2)
Graphite2)
FKM (optional FFKM)2)
Thermal isolator
Optional
Standard
Optional
Extension
User selectable length
User selectable length
User selectable cable length
1)
Zirconium Oxide
2)
For caustic materials, consult a local sales person for alternative O-rings. For more information, please visit http://www.automation.siemens.com/aspa_app.
4/44
Siemens FI 01 · 2016
© Siemens AG 2016
Level Measurement
Point level measurement - RF Capacitance switches
Pointek CLS300 - Standard
Selection and Ordering data
Article No.
Selection and Ordering data
Article No.
Pointek CLS300 - Standard - Rod Version
with Threaded or Flanged process connection
Inverse frequency shift capacitance level and
material detection switch with optional rod/cable
choices and configurable output. CLS300 is ideal
for detecting liquids, solids, slurries, foam, and
interfaces in demanding conditions where high
pressure and temperatures are present, and has
the ability to tune out buildup on the probe.
7ML5650-
Pointek CLS300 - Standard - Rod Version
with Threaded or Flanged process connection
Inverse frequency shift capacitance level and
material detection switch with optional rod/cable
choices and configurable output. CLS300 is ideal
for detecting liquids, solids, slurries, foam, and
interfaces in demanding conditions where high
pressure and temperatures are present, and has
the ability to tune out buildup on the probe.
7ML5650-
77777 - 7777
Click on the Article No. for the online configuration in the PIA Life Cycle Portal.
Add Order code Y01 and plain text:
"Insertion length ... mm"
Extended rod, factory adjusted length
250 ... 499 mm (9.8 ... 19.65 inch)
Extended rod, factory adjusted length
500 ... 749 mm (19.69 ... 29.49 inch)
Extended rod, factory adjusted length
750 ... 999 mm (29.53 ... 39.3 inch)
Process connection
Threaded, 316L stainless steel
¾" NPT [(Taper), ANSI/ASME B1.20.1]
1" NPT [(Taper), ANSI/ASME B1.20.1]
1¼" NPT [(Taper), ANSI/ASME B1.20.1]
 0A
 0B
 0C
1½" NPT [(Taper), ANSI/ASME B1.20.1]
R ¾" [(BSPT), EN 10226/PT (JIS-T), JIS B 0203]
R 1" [(BSPT), EN 10226/PT (JIS-T), JIS B 0203]
 0D
 1A
 1B
R 1½" [(BSPT), EN 10226/PT (JIS-T),
JIS B 0203]
 1D
G ¾" [(BSPP), EN ISO 228-1/PF (JIS-P),
JIS B 0202]
G 1" [(BSPP), EN ISO 228-1/PF (JIS-P),
JIS B 0202]
G 1½" [(BSPP), EN ISO 228-1/PF (JIS-P),
JIS B 0202]
 3A
 3B
 3D
Welded flange, 316L stainless steel, raised face

E

F

G
Thermal isolator
Without thermal isolator
With thermal isolator [for process connection
temperatures over 85 °C (185 °F)]


Wetted seals
FKM
FFKM [for process temperatures above
-20 °C (-4 °F)]


Probe material
316L stainless steel with PFA lining and PEEK
isolators

4
0
1
0
1
0
Approvals
1" ASME, 150 lb
1" ASME, 300 lb
1" ASME, 600 lb
 5A
5B
5C
1½" ASME, 150 lb
1½" ASME, 300 lb
1½" ASME, 600 lb
 5D
5E
5F
2" ASME, 150 lb
2" ASME, 300 lb
2" ASME, 600 lb
 5G
5H
5J
3" ASME, 150 lb
3" ASME, 300 lb
3" ASME, 600 lb
 5K
5L
5M
4" ASME, 150 lb
4" ASME, 300 lb
4" ASME, 600 lb
 5N
5P
5Q
Welded flange, 316L stainless steel,
Type A flat faced
DN 25, PN 16
DN 25, PN 40
DN 40, PN 16
 6A
6B
 6C
DN 40, PN 40
DN 50, PN 16
DN 50, PN 40
6D
 6E
6F
DN 80, PN 16
DN 80, PN 40
DN 100, PN 16
 6G
6H
 6J
Dust Ignition Proof with IS Probe:
CE, RCM, ATEX II 1/2 D T100 °C

C
Flameproof Enclosure with IS Probe:
CE, RCM, ATEX II 1/2 G EEx d[ia] IIC T6 ... T1,
ATEX II 1/2 D T100 °C
Flameproof Enclosure with IS Probe,
with WHG approval:
CE, RCM, ATEX II 1/2 G EEx d[ia] IIC T6 ... T1,
ATEX II 1/2 D T100 °C

D

E
Dust Ignition Proof with IS Probe:
CSA/FM Class II, Div. 1, Groups E, F, G
CSA/FM Class III T4

F
Explosion Proof Enclosure with IS Probe:
CSA/FM Class I, Div. 1, Groups A, B, C, D
CSA/FM Class II, Div. 1, Groups E, F, G
CSA/FM Class III T4

G
General Purpose (CSA, FM)

H
General Purpose (CE, RCM)

J
General Purpose with WHG approval
(CSA, FM, CE, RCM)

K
Enclosure and lid
Aluminum epoxy coated
2 x ½" NPT via adapter - cable inlet, IP65
2 x M20 x 1.5 cable inlet, IP65
2 x ½" NPT via adapter - cable inlet, IP68
2 x M20 x 1.5 cable inlet, IP68
Active shield length
Standard length (125 mm threaded, 105 mm flanged)
Extended shield (250 mm threaded, 230 mm flanged)1)
Extended shield (400 mm threaded, 380 mm flanged)2)
6K
DN 100, PN 40
(Note: Flange bolting patterns and facings
dimensionally correspond to the applicable
ASME B16.5 or EN 1092-1 standard.)
Probe length (length from flange face)
(threaded lengths include process thread)
Note: No Y01 needed in Order code for
standard lengths
Standard version, rod 350 mm (13.78 inch)
Extended rod, length 500 mm (19.69 inch)
Extended rod, length 750 mm (29.53 inch)
Extended rod, length 1 000 mm (39.37 inch)
77777 - 7777
1)




A
B
C
D
2)




A
B
C
D

0

1

2
Available with Probe version options B ... D, F, G only
[ 500 mm (19.69 inch)]
Available with Probe version options C, D, and G only
[ 750 mm (29.53 inch)]
 We can offer shorter delivery times for configurations designated with the
Quick Ship Symbol . For details see page 9/5 in the appendix.
Siemens FI 01 · 2016
4/45
© Siemens AG 2016
Level Measurement
Point level measurement - RF Capacitance switches
Pointek CLS300 - Standard
Selection and Ordering data
Order code
Further designs
Please add "-Z" to Article No. and specify Order
code(s).
Total insertion length: enter the total insertion length  Y01
in plain text description
Stainless steel tag [69 x 50 mm (2.71 x 1.97 inch)]:  Y15
Measuring-point number/identification
(max. 27 characters) specify in plain text
Manufacturer's test certificate: M to DIN 55350,
Part 18 and to ISO 9000
 C11
Inspection Certificate Type 3.1 per EN 10204
 C12
Operating Instructions
4
Note: The Operating Instructions should be
ordered as a separate line on the order.
This device is shipped with the Siemens Level and
Weighing manual DVD containing the ATEX Quick
Start and manual library.
See page 4/56
Accessories
See page 4/56
 We can offer shorter delivery times for configurations designated with the
Quick Ship Symbol . For details see page 9/5 in the appendix.
Selection and Ordering data
Article No.
Pointek CLS300 - Standard - Cable Version
with Threaded or Flanged process connection
Inverse frequency shift capacitance level and
material detection switch with optional rod/cable
choices and configurable output. CLS300 is ideal
for detecting liquids, solids, slurries, foam, and
interfaces in demanding conditions where high
pressure and temperatures are present, and has
the ability to tune out buildup on the probe.
7ML56517 7 7 77 - 77 7 7
Click on the Article No. for the online configuration in the PIA Life Cycle Portal.
Process connection
Threaded, 316L stainless steel
1¼" NPT [(Taper), ANSI/ASME B1.20.1]
1½" NPT [(Taper), ANSI/ASME B1.20.1]
R 1½" [(BSPT), EN 10226/PT (JIS-T),
JIS B 0203]
G 1½" [(BSPP), EN ISO 228-1/PF (JIS-P),
JIS B 0202]
 0C
 0D
 1D
 3D
Welded flange, 316L stainless steel, raised face
1½" ASME, 150 lb
1½" ASME, 300 lb
1½" ASME, 600 lb
 5D
5E
5F
2" ASME, 150 lb
2" ASME, 300 lb
2" ASME, 600 lb
 5G
5H
5J
3" ASME, 150 lb
3" ASME, 300 lb
3" ASME, 600 lb
 5K
5L
5M
4" ASME, 150 lb
4" ASME, 300 lb
4" ASME, 600 lb
 5N
5P
5Q
Welded flange, 316L stainless steel,
Type A flat faced
DN 40, PN 16
DN 40, PN 40
DN 50, PN 16
 6C
6D
 6E
DN 50, PN 40
DN 80, PN 16
DN 80, PN 40
6F
 6G
6H
DN 100, PN 16
DN 100, PN 40
(Note: Flange bolting patterns and facings
dimensionally correspond to the applicable
ASME B16.5 or EN 1092-1 standard.)
 6J
6K
Probe length (length from flange face)
(threaded lengths include process thread)
Note: No Y01 needed in Order code for
standard lengths
Extended cable, 3 000 mm (118.11 inch),
length can be shortened by customer
Extended cable, 6 000 mm (236.22 inch),
length can be shortened by customer

A

B
Extended cable, 500 ... 1 000 mm
(19.69 ... 39.37 inch)

E
Extended cable, 1 001 ... 5 000 mm
(39.41 ... 196.85 inch)

F
Extended cable, 5 001 ... 10 000 mm
(196.89 ... 393.70 inch)

G
Extended cable, 10 001 ... 15 000 mm
(393.74 ... 590.55 inch)
Extended cable, 15 001 ... 20 000 mm
(590.59 ... 787.40 inch)

H

J
Extended cable, 20 001 ... 25 000 mm
(787.44 ... 984.25 inch)

K
Add Order code Y01 and plain text:
"Insertion length ... mm"
4/46
Siemens FI 01 · 2016
© Siemens AG 2016
Level Measurement
Point level measurement - RF Capacitance switches
Pointek CLS300 - Standard
Order code
Selection and Ordering data
Article No.
Selection and Ordering data
Pointek CLS300 - Standard - Cable Version
with Threaded or Flanged process connection
Inverse frequency shift capacitance level and
material detection switch with optional rod/cable
choices and configurable output. CLS300 is ideal
for detecting liquids, solids, slurries, foam, and
interfaces in demanding conditions where high
pressure and temperatures are present, and has
the ability to tune out buildup on the probe.
7ML5651-
Further designs
77 7 77 - 77 77
Please add "-Z" to Article No. and specify Order
code(s).
Thermal isolator
Without thermal isolator
With thermal isolator [for process connection
temperatures over 85 °C (185 °F)]
Wetted seals
FKM
FFKM [for process temperatures above
-20 °C (-4 °F)]
Total insertion length: enter the total insertion length  Y01
in plain text description
Stainless steel tag [69 x 50 mm (2.71 x 1.97 inch)]:  Y15
Measuring-point number/identification
(max. 27 characters) specify in plain text


0
1
Manufacturer's test certificate: M to DIN 55350,
Part 18 and to ISO 9000
 C11
Inspection Certificate Type 3.1 per EN 10204
 C12
Operating Instructions


Probe material
Bare 316L stainless steel cable, PEEK isolators and 
316L stainless steel cable weight
PFA coated cable, PEEK isolators and 316L

stainless steel cable weight
0
1
0
1
Note: The Operating Instructions should be
ordered as a separate line on the order.
This device is shipped with the Siemens Level and
Weighing manual DVD containing the ATEX Quick
Start and manual library.
See page 4/56
Accessories
See page 4/56
4
 We can offer shorter delivery times for configurations designated with the
Quick Ship Symbol . For details see page 9/5 in the appendix.
Approvals
Dust Ignition Proof with IS Probe:
CE, RCM, ATEX II 1/2 D T100 °C

C
Flameproof Enclosure with IS Probe:
CE, RCM, ATEX II 1/2 G EEx d[ia] IIC T6 ... T1,
ATEX II 1/2 D T100 °C
Flameproof Enclosure with IS Probe,
with WHG approval:
CE, RCM, ATEX II 1/2 G EEx d[ia] IIC T6 ... T1,
ATEX II 1/2 D T100 °C

D

E
Dust Ignition Proof with IS Probe:
CSA/FM Class II, Div. 1, Groups E, F, G
CSA/FM Class III T4

F
Explosion Proof Enclosure with IS Probe:
CSA/FM Class I, Div. 1, Groups A, B, C, D
CSA/FM Class II, Div. 1, Groups E, F, G
CSA/FM Class III T4

G
General Purpose (CSA, FM)

H
General Purpose (CE, RCM)

J
General Purpose with WHG approval
(CSA, FM, CE, RCM)

K
Enclosure and lid
Aluminum epoxy coated
2 x ½" NPT via adapter - cable inlet, IP65
2 x M20 x 1.5 cable inlet, IP65
2 x ½" NPT via adapter - cable inlet, IP68
2 x M20 x 1.5 cable inlet, IP68
Active shield length
Standard length (125 mm threaded, 105 mm flanged)
Extended shield (250 mm threaded, 230 mm flanged)1)
Extended shield (400 mm threaded, 380 mm flanged)1)
1)




A
B
C
D

0

1

2
Available with Probe version options A, B, F ... K, only
[ 1 000 mm (39.7 inch)]
 We can offer shorter delivery times for configurations designated with the
Quick Ship Symbol . For details see page 9/5 in the appendix.
Siemens FI 01 · 2016
4/47
© Siemens AG 2016
Level Measurement
Point level measurement - RF Capacitance switches
Pointek CLS300 - Standard
Selection and Ordering data
Article No.
Selection and Ordering data
Article No.
Pointek CLS300 - Standard - High Temperature
Rod Version with Threaded or Flanged process
connection
Inverse frequency shift capacitance level and
material detection switch with optional rod/cable
choices and configurable output. CLS300 is ideal
for detecting liquids, solids, slurries, foam, and
interfaces in demanding conditions where high
pressure and temperatures are present, and has
the ability to tune out buildup on the probe.
7ML5652-
Pointek CLS300 - Standard - High Temperature
Rod Version with Threaded or Flanged process
connection
Inverse frequency shift capacitance level and
material detection switch with optional rod/cable
choices and configurable output. CLS300 is ideal
for detecting liquids, solids, slurries, foam, and
interfaces in demanding conditions where high
pressure and temperatures are present, and has
the ability to tune out buildup on the probe.
7ML5652-
7 7 7 00 7 - 7 7 7 7
Click on the Article No. for the online configuration in the PIA Life Cycle Portal.
Add Order code Y01 and plain text:
"Insertion length ... mm"
Extended rod, factory adjusted length
250 ... 499 mm (9.8 ... 19.65 inch)
Extended rod, factory adjusted length
500 ... 749 mm (19.69 ... 29.49 inch)
Extended rod, factory adjusted length
750 ... 999 mm (29.53 ... 39.3 inch)
Process connection
Threaded, 316L stainless steel
4
¾" NPT [(Taper), ANSI/ASME B1.20.1]
1" NPT [(Taper), ANSI/ASME B1.20.1]
1¼" NPT [(Taper), ANSI/ASME B1.20.1]
 0A
 0B
 0C
1½" NPT [(Taper), ANSI/ASME B1.20.1]
R ¾" [(BSPT), EN 10226/PT (JIS-T), JIS B 0203]
R 1" [(BSPT), EN 10226/PT (JIS-T), JIS B 0203]
 0D
 1A
 1B
R 1½" [(BSPT), EN 10226/PT (JIS-T),
JIS B 0203]
G ¾" [(BSPP), EN ISO 228-1/PF (JIS-P),
JIS B 0202]
G 1" [(BSPP), EN ISO 228-1/PF (JIS-P),
JIS B 0202]
G 1½" [(BSPP), EN ISO 228-1/PF (JIS-P),
JIS B 0202]
 3D

F

G

 1D

 3A
Approvals
 3B
Dust Ignition Proof with IS Probe:
CE, RCM, ATEX II 1/2 D T100 °C

C
Flameproof Enclosure with IS Probe:
CE, RCM, ATEX II 1/2 G EEx d[ia] IIC T6 ... T1,
ATEXII 1/2 D T100 °C
Flameproof Enclosure with IS Probe,
with WHG approval:
CE, RCM, ATEX II 1/2 G EEx d[ia] IIC T6 ... T1,
ATEX II 1/2 D T100 °C

D

E
Dust Ignition Proof with IS Probe:
CSA/FM Class II, Div. 1, Groups E, F, G
CSA/FM Class III T4

F
Explosion Proof Enclosure with IS Probe:
CSA/FM Class I, Div. 1, Groups A, B, C, D
CSA/FM Class II, Div. 1, Groups E, F, G
CSA/FM Class III T4

G
General Purpose (CSA, FM)

H
General Purpose (CE, RCM)

J
General Purpose with WHG approval
(CSA, FM, CE, RCM)

K
 5A
5B
5C
1½" ASME, 150 lb
1½" ASME, 300 lb
1½" ASME, 600 lb
 5D
5E
5F
2" ASME, 150 lb
2" ASME, 300 lb
2" ASME, 600 lb
 5G
5H
5J
3" ASME, 150 lb
3" ASME, 300 lb
3" ASME, 600 lb
 5K
5L
5M
4" ASME, 150 lb
4" ASME, 300 lb
4" ASME, 600 lb
 5N
5P
5Q
Welded flange, 316L stainless steel,
Type A flat faced
DN 25, PN 16
DN 25, PN 40
DN 40, PN 16
 6A
6B
 6C
DN 40, PN 40
DN 50, PN 16
DN 50, PN 40
6D
 6E
6F
DN 80, PN 16
DN 80, PN 40
DN 100, PN 16
 6G
6H
 6J
0
0
Enclosure and lid
Aluminum epoxy coated
2 x ½" NPT via adapter - cable inlet, IP65
2 x M20 x 1.5 cable inlet, IP65


A
B
2 x ½" NPT via adapter - cable inlet, IP68
2 x M20 x 1.5 cable inlet, IP68


C
D
Active shield length
Standard length (125 mm threaded, 105 mm flanged)
Extended shield (250 mm threaded, 230 mm flanged)1)
Extended shield (400 mm threaded, 380 mm flanged)2)
6K
DN 100, PN 40
(Note: Flange bolting patterns and facings
dimensionally correspond to the applicable
ASME B16.5 or EN 1092-1 standard.)

0

1

2
1)
Available with Probe version options B ... D, F, G only
[ 500 mm (19.69 inch)]
2)
Available with Probe version options C, D, and G only
[ 750 mm (29.53 inch)]
 We can offer shorter delivery times for configurations designated with the
Quick Ship Symbol . For details see page 9/5 in the appendix.
Probe length (length from flange face)
(threaded lengths include process thread)
Note: No Y01 needed in Order code for
standard lengths
Siemens FI 01 · 2016
E
Probe material
316L stainless steel with ceramic (ZrO2) isolators
1" ASME, 150 lb
1" ASME, 300 lb
1" ASME, 600 lb
4/48

Wetted seals
Graphite
Welded flange, 316L stainless steel, raised face
Standard version rod, 350 mm (13.78 inch)
Extended rod, length 500 mm (19.69 inch)
Extended rod, length 750 mm (29.53 inch)
Extended rod, length 1 000 mm (39.37 inch)
7 7 7 00 7 - 7 7 7 7




A
B
C
D
© Siemens AG 2016
Level Measurement
Point level measurement - RF Capacitance switches
Pointek CLS300 - Standard
Selection and Ordering data
Order code
Further designs
Please add "-Z" to Article No. and specify Order
code(s).
Total insertion length: enter the total insertion length  Y01
in plain text description
Stainless steel tag [69 x 50 mm (2.71 x 1.97 inch)]:  Y15
Measuring-point number/identification
(max. 27 characters) specify in plain text
Manufacturer's test certificate: M to DIN 55350,
Part 18 and to ISO 9000
 C11
Inspection Certificate Type 3.1 per EN 10204
 C12
Operating Instructions
Note: The Operating Instructions should be
ordered as a separate line on the order.
This device is shipped with the Siemens Level and
Weighing manual DVD containing the ATEX Quick
Start and manual library.
See page 4/56
Accessories
See page 4/56
4
 We can offer shorter delivery times for configurations designated with the
Quick Ship Symbol . For details see page 9/5 in the appendix.
Siemens FI 01 · 2016
4/49
© Siemens AG 2016
Level Measurement
Point level measurement - RF Capacitance switches
Pointek CLS300 - Digital
■ Overview
■ Configuration
Installation
4
Pointek CLS300 (digital version) is an inverse frequency shift
capacitance level and material detection switch with optional
rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding
conditions where high pressure and temperatures are present
and has the ability to tune out buildup on the probe. The digital
version includes PROFIBUS PA, an LCD display, and advanced
diagnostic features.
Keep unit out of path of falling material, or protect probe from
falling material.
■ Benefits
• Active-Shield technology so measurement is unaffected by
material buildup or nozzle interference in active shield section
• Performs in extremely abrasive conditions because of solid
rod construction
• Push-button calibration, full-function diagnostics
• High sensitivity allows installation in a wide range of liquids,
solids or slurry applications
• Integral LCD display allows for easy menu-driven setup
• PROFIBUS PA communication (SIMATIC PDM compatible)
Build up of material in active shield area does not affect
switch operation.
■ Application
M
in
.5
Pointek CLS300 digital version provides an integral LCD display
for stand-alone use, with PROFIBUS PA communication
(Profile version 3.0, Class B) when required. Solid-state switch
alarm is standard.
0
)
(2
The robust design of CLS300 makes it specifically applicable for
heavy solids applications where abrasive materials occur as in
the mining industry.
The fully potted electronics are unaffected by condensation,
dust or vibration.
Wetted parts are made of stainless steel with a PFA shield for
high chemical resistance, and of ceramic and stainless steel for
high temperature version. Materials with low or high dielectric
constants can be accurately detected. The unique Active Shield
suppresses interference from material buildup or long installation nozzles.
The unique modular design of the Pointek CLS300 provides a
wide range of configurations, process connections, extensions
and approvals to meet the temperature and pressure requirements of specific applications. The modular design makes ordering easier and reduces stocking requirements. A wide range
of probe configurations are available, including rod and cable
versions.
• Key Applications: liquids, slurries, bulk solids, relatively high
pressure and temperature, hazardous areas, milling and
mining applications
4/50
Siemens FI 01 · 2016
Min.
50 (2)
Install probe at least 50 (2) from tank wall.
Note angle of repose and adjust accordingly.
Pointek CLS300 installation, dimensions in mm (inch)
© Siemens AG 2016
Level Measurement
Point level measurement - RF Capacitance switches
Pointek CLS300 - Digital
■ Technical specifications
Mode of operation
Measuring principle
Inverse frequency shift capacitive
level detection
Input
Measured variable
• Max. load current
• Voltage drop
• Time delay (pre or post switching)
Galvanically isolated
Against reversed polarity (bipolar)
• 30 V (DC)
• 30 V peak (AC)
82 mA
< 1 V, typical at 50 mA
Programmable by user (0 ... 100 s)
Fail-safe mode
Min. or max.
Connection
Removable terminal block
Dust Ignition Proof With IS Probe
Intrinsically Safe4)
Non-incendive
Accuracy
Resolution
• Min. sensitivity (pF)
• Max. temperature error
Current consumption
Certificates and approvals
General Purpose
Dust Ignition Proof
Flameproof Enclosure With IS Probe
Change in picoFarad (pF)
Output
Solid-state output
• Output
• Protection
• Max. switching voltage
Power supply
Bus voltage (at process connection)
1 % change in actual capacitance
0.2 % of actual capacitance value
Explosion Proof with IS Probe
Rated operating conditions1)
Installation conditions
• Location
Ambient conditions
• Ambient temperature
Medium conditions
• Relative dielectric constant r
• Process temperature
- Rod/Cable version
- High Temperature version
• Process pressure3)
Design
Material (enclosure)
Degree of protection
Cable inlet
Controls and displays
Local display
Configuration
Indoor/outdoor
-40 ... +85 °C (-40 ... +185
Marine
°F)2)
Liquids, bulk solids, slurries, and
interfaces, and applications with viscous materials
Min. 1.5
Others
Communication
• Standard: 12 ... 30 V DC
• Intrinsically Safe: 12 ... 24 V DC
12.5 mA
CSA, FM, CE, RCM
ATEX II 1/2 D, 2 D IP6X T100 °C
ATEX II 1/2 G EEx d[ia] IIC T6 ... T4
ATEX II 1/2 D T100 °C
CSA/FM Class II, Div. 1,
Groups E, F, G
CSA/FM Class III T4
ATEX II 1 G EEx ia IIC T6 ... T4
ATEX II 1/2 D, 2 D IP6X T100 °C
CSA/FM Class I, Div. 1,
Groups A, B, C, D
CSA/FM Class II, Div. 1,
Groups E, F, G
CSA/FM Class III T4
CSA/FM Class I, Div. 2,
Groups A, B, C, D
CSA/FM Class II, Div. 2,
Groups F, G
CSA/FM Class III T4 or T6
CSA/FM Class I, Div. 1,
Groups A, B, C, D
CSA/FM Class II, Div. 1,
Groups E, F, G
CSA/FM Class III T4
Lloyds Register of Shipping,
Categories ENV1, ENV2, and ENV5
Pattern Approval (China)
PROFIBUS PA (IEC 61158 CPF3
CP3/2)
Bus physical layer: IEC 61158-2
MBP-(IS)
Device profile: PROFIBUS PA profile
for Process Control Devices Version
3.0, Class B
-40 ... +200 °C (-40 ... +392 °F)2)
-40 ... +400 °C (-40 ... +752 °F)
-1 ... +35 bar g (-14.6 ... +511 psi g)
FISCO field device
1)
Powder-coated aluminum with gasket
Standard: Type 4/NEMA 4/IP65
Optional: Type 4/NEMA 4/IP68
2 x M20 x 1.5 thread
(option: 2 x ½" NPT conduit entry
including 1 plugged entry)
LCD
• Locally, using 3 button keypad (for
standalone operation)
• Remotely, using SIMATIC PDM (for
installation on a network)
When operation is in areas classified as hazardous, observe restrictions
according to relevant certificate. See also Pressure/Temperature curves
starting on page 4/57.
2) Thermal isolator is used if process connection temperature exceeds 85 °C
(185 °F)
3)
Pressure rating of process seal is temperature dependent. See Pressure/
Temperature curves starting on page 4/57.
4)
Barrier or Intrinsically Safe power supply required for Intrinsically Safe
protection
Design: Probe
Rod version
High Temperature version
Cable version
Length
Min. 250 mm (9.8 inch),
max. 1 000 mm (40 inch)
Min. 250 mm (9.8 inch),
max. 1 000 mm (40 inch)
Min. 1 000 mm (40 inch),
max. 25 000 mm (984 inch)
Sensor wetted parts
PFA (no insulation on active probe),
316L stainless steel, PEEK isolators
Ceramic (ZrO21)) isolators
(no insulation on active probe),
316L stainless steel
316 stainless steel, optional PFA,
PEEK isolators
O-ring seal material
FKM (optional FFKM)2)
Graphite2)
FKM (optional FFKM)2)
Thermal isolator
Optional
Standard
Optional
Extension
User selectable length
User selectable length
User selectable cable length
1)
Zirconium Oxide
2)
For caustic materials, consult a local sales person for alternative O-rings. For more information, please visit http://www.automation.siemens.com/aspa_app.
Siemens FI 01 · 2016
4/51
4
© Siemens AG 2016
Level Measurement
Point level measurement - RF Capacitance switches
Pointek CLS300 - Digital
Selection and Ordering data
Article No.
Selection and Ordering data
Article No.
Pointek CLS300 - Digital - Rod with
Threaded or Flanged process connection
Inverse frequency shift capacitance level and
material detection switch with optional rod/cable
choices and configurable output. It is ideal for
detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure
and temperatures are present and has the ability to
tune out buildup on the probe.
7ML5660-
Pointek CLS300 - Digital - Rod with
Threaded or Flanged process connection
Inverse frequency shift capacitance level and
material detection switch with optional rod/cable
choices and configurable output. It is ideal for
detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure
and temperatures are present and has the ability to
tune out buildup on the probe.
7ML5660-
77 7 77 - 77 77
Click on the Article No. for the online configuration in the PIA Life Cycle Portal.
Add Order code Y01 and plain text:
"Insertion length ... mm"
Extended rod, factory adjusted length
250 ... 499 mm (9.8 ... 19.65 inch)
Extended rod, factory adjusted length
500 ... 749 mm (19.69 ... 29.49 inch)
Extended rod, factory adjusted length
750 ... 999 mm (29.53 ... 39.3 inch)
Process connection
Threaded, 316L stainless steel
4
¾" NPT [(Taper), ANSI/ASME B1.20.1]
1" NPT [(Taper), ANSI/ASME B1.20.1]
1¼" NPT [(Taper), ANSI/ASME B1.20.1]
 0A
 0B
 0C
1½" NPT [(Taper), ANSI/ASME B1.20.1]
R ¾" [(BSPT), EN 10226/PT (JIS-T), JIS B 0203]
R 1" [(BSPT), EN 10226/PT (JIS-T), JIS B 0203]
 0D
 1A
 1B
R 1½" [(BSPT), EN 10226/PT (JIS-T),
JIS B 0203]
G ¾" [(BSPP), EN ISO 228-1/PF (JIS-P),
JIS B 0202]
G 1" [(BSPP), EN ISO 228-1/PF (JIS-P),
JIS B 0202]
 1D
G 1½" [(BSPP), EN ISO 228-1/PF (JIS-P),
JIS B 0202]
 3D
Thermal isolator
Without thermal isolator
With thermal isolator [for process connection
temperatures over 85 °C (185 °F)]
 3B
 5A
5B
5C
1½" ASME, 150 lb
1½" ASME, 300 lb
1½" ASME, 600 lb
 5D
5E
5F
2" ASME, 150 lb
2" ASME, 300 lb
 5G
5H
2" ASME, 600 lb
5J
3" ASME, 150 lb
3" ASME, 300 lb
3" ASME, 600 lb
 5K
5L
5M
4" ASME, 150 lb
4" ASME, 300 lb
4" ASME, 600 lb
 5N
5P
5Q
Welded flange, 316L stainless steel,
Type A flat faced
DN 25, PN 16
DN 25, PN 40
DN 40, PN 16
 6A
6B
 6C
DN 40, PN 40
DN 50, PN 16
DN 50, PN 40
6D
 6E
6F
DN 80, PN 16
DN 80, PN 40
DN 100, PN 16
 6G
6H
 6J
Probe material
316L stainless steel with PFA lining and PEEK
isolators

F

G

0

1

0
1
0
Probe length (length from flange face)
(threaded lengths include process thread)
Note: No Y01 needed in Order code for
standard lengths




Dust Ignition Proof:
CE, RCM, ATEX II 1/2 D, 2 D IP6X T100 °C

B
Intrinsically Safe1)
CE, RCM, ATEX II 1 G EEx ia IIC T6 ... T4,
ATEX II 1/2 D, 2 D IP6X T100 °C

C
Flameproof Enclosure with IS Probe:
CE, RCM, ATEX II 1/2 G EEx d[ia] IIC T6 ... T4,
ATEX II 1/2 D T100 °C

D
Dust Ignition Proof with IS Probe:
CSA/FM Class II, Div. 1, Groups E, F, G
CSA/FM Class III T4

E
Intrinsically Safe1)
CSA/FM Class I, Div. 1, Groups A, B, C, D
CSA/FM Class II, Div. 1, Groups E, F, G
CSA/FM Class III T4

F
Explosion Proof Enclosure with IS Probe:
CSA/FM Class I, Div. 1, Groups A, B, C, D
CSA/FM Class II, Div. 1, Groups E, F, G
CSA/FM Class III T4

G
General Purpose (CSA, FM)

H
General Purpose (CSA, FM, CE, RCM)

J
 We can offer shorter delivery times for configurations designated with the
Quick Ship Symbol . For details see page 9/5 in the appendix.
6K
DN 100, PN 40
(Note: Flange bolting patterns and facings
dimensionally correspond to the applicable
ASME B16.5 or EN 1092-1 standard.)
Siemens FI 01 · 2016
E
Approvals
1" ASME, 150 lb
1" ASME, 300 lb
1" ASME, 600 lb
4/52

Wetted seals
FKM

FFKM [for process temperatures above -20 °C (-4 °F)]
 3A
Welded flange, 316L stainless steel, raised face
Standard version, rod 350 mm (13.78 inch)
Extended rod, length 500 mm (19.69 inch)
Extended rod, length 750 mm (29.53 inch)
Extended rod, length 1 000 mm (39.37 inch)
7 7 7 77 - 77 7 7
A
B
C
D
© Siemens AG 2016
Level Measurement
Point level measurement - RF Capacitance switches
Pointek CLS300 - Digital
Selection and Ordering data
Article No.
Selection and Ordering data
Article No.
Pointek CLS300 - Digital - Rod with
Threaded or Flanged process connection
Inverse frequency shift capacitance level and
material detection switch with optional rod/cable
choices and configurable output. It is ideal for
detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure
and temperatures are present and has the ability to
tune out buildup on the probe.
7ML5660-
Pointek CLS300 - Digital - Cable with
Threaded or Flanged process connection
Inverse frequency shift capacitance level and
material detection switch with optional rod/cable
choices and configurable output. It is ideal for
detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure
and temperatures are present and has the ability to
tune out buildup on the probe.
7ML5661-
77 7 77 - 77 77
Click on the Article No. for the online configuration in the PIA Life Cycle Portal.
Enclosure and Lid
Aluminum epoxy coated
2 x ½" NPT via adapter - cable inlet, IP65
2 x M20 x 1.5 cable inlet, IP65
2 x ½" NPT via adapter - cable inlet, IP68
2 x M20 x 1.5 cable inlet, IP68
Active shield length
Standard length (125 mm threaded, 105 mm flanged)
Extended shield (250 mm threaded, 230 mm flanged)2)
Extended shield (400 mm threaded, 380 mm flanged)3)




Process connection
Threaded, 316L stainless steel
A
B
C
D

0

1

2
Barrier or Intrinsically Safe power supply required for Intrinsically Safe
protection
2) Available with Probe version options B ... D, F, G only
[ 500 mm (19.69 inch)]
Available with Probe version options C, D, and G only
[ 750 mm (29.53 inch)]
 We can offer shorter delivery times for configurations designated with the
Quick Ship Symbol . For details see page 9/5 in the appendix.
Selection and Ordering data
1¼" NPT [(Taper), ANSI/ASME B1.20.1]

1½" NPT [(Taper), ANSI/ASME B1.20.1]

R 1½" [(BSPT), EN 10226/PT (JIS-T), JIS B 0203] 
G 1½" [(BSPP), EN ISO 228-1/PF (JIS-P), JIS B 0202] 
0C
0D
1D
3D
4
Welded flange, 316L stainless steel, raised face
1)
3)
7 7 7 77 - 77 7 7
Order code
Further designs
Please add "-Z" to Article No. and specify Order
code(s).
Total insertion length: enter the total insertion length  Y01
in plain text description
Stainless steel tag [69 x 50 mm (2.71 x 1.97 inch)]:  Y15
Measuring-point number/identification
(max. 27 characters) specify in plain text
Manufacturer's test certificate: M to DIN 55350,
Part 18 and to ISO 9000
 C11
Inspection Certificate Type 3.1 per EN 10204
 C12
Operating Instructions
Note: The Operating Instructions should be
ordered as a separate line on the order.
This device is shipped with the Siemens Level and
Weighing manual DVD containing the ATEX Quick
Start and manual library.
See page 4/56
Accessories
See page 4/56
 We can offer shorter delivery times for configurations designated with the
Quick Ship Symbol . For details see page 9/5 in the appendix.
1½" ASME, 150 lb
1½" ASME, 300 lb
1½" ASME, 600 lb
 5D
5E
5F
2" ASME, 150 lb
2" ASME, 300 lb
2" ASME, 600 lb
 5G
5H
5J
3" ASME, 150 lb
3" ASME, 300 lb
3" ASME, 600 lb
 5K
5L
5M
4" ASME, 150 lb
4" ASME, 300 lb
4" ASME, 600 lb
 5N
5P
5Q
Welded flange, 316L stainless steel,
Type A flat faced
DN 40, PN 16
DN 40, PN 40
DN 50, PN 16
 6C
6D
 6E
DN 50, PN 40
DN 80, PN 16
DN 80, PN 40
6F
 6G
6H
DN 100, PN 16
DN 100, PN 40
(Note: Flange bolting patterns and facings
dimensionally correspond to the applicable
ASME B16.5 or EN 1092-1 standard.)
 6J
6K
Probe length (length from flange face)
(threaded lengths include process thread)
Note: No Y01 needed in Order code for
standard lengths
Extended cable, 3 000 mm (118.11 inch),
length can be shortened by customer
Extended cable, 6 000 mm (236.22 inch),
length can be shortened by customer
Add Order code Y01 and plain text:
"Insertion length ... mm"
Extended cable, 500 ... 1 000 mm
(19.69 ... 39.37 inch)
Extended cable, 1 001 ... 5 000 mm
(39.41 ... 196.85 inch)
Extended cable, 5 001 ... 10 000 mm
(196.89 ... 393.70 inch)
Extended cable, 10 001 ... 15 000 mm
(393.74 ... 590.55 inch)
Extended cable, 15 001 ... 20 000 mm
(590.59 ... 787.40 inch)
Extended cable, 20 001 ... 25 000 mm
(787.44 ... 984.25 inch)

A

B

E

F

G

H

J

K
Siemens FI 01 · 2016
4/53
© Siemens AG 2016
Level Measurement
Point level measurement - RF Capacitance switches
Pointek CLS300 - Digital
Selection and Ordering data
Article No.
Selection and Ordering data
Pointek CLS300 - Digital - Cable with
Threaded or Flanged process connection
Inverse frequency shift capacitance level and
material detection switch with optional rod/cable
choices and configurable output. It is ideal for
detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure
and temperatures are present and has the ability to
tune out buildup on the probe.
7ML5661-
Further designs
77 7 77 - 77 77
Please add "-Z" to Article No. and specify Order
code(s).
Thermal isolator
Without thermal isolator
With thermal isolator [for process connection
temperatures over 85 °C (185 °F)]
Total insertion length: enter the total insertion length  Y01
in plain text description
Stainless steel tag [69 x 50 mm (2.71 x 1.97 inch)]:  Y15
Measuring-point number/identification
(max. 27 characters) specify in plain text


Wetted seals
FKM

FFKM [for process temperatures above -20 °C (-4 °F)]
4
Probe material
Bare 316L stainless steel cable, PEEK isolators and 
316L stainless steel cable weight
PFA coated cable, PEEK isolators and 316L

stainless steel cable weight
0
1
0
1
 C12
0
1
Accessories
See page 4/56
 We can offer shorter delivery times for configurations designated with the
Quick Ship Symbol . For details see page 9/5 in the appendix.
B
Intrinsically Safe1)
CE, RCM, ATEX II 1 G EEx ia IIC T6 ... T4,
ATEX II 1/2 D, 2 D IP6X T100 °C

C
Flameproof Enclosure with IS Probe:
CE, RCM, ATEX II 1/2 G EEx d[ia] IIC T6 ... T4,
ATEX II 1/2 D T100 °C

D
Intrinsically Safe1)
CSA/FM Class I, Div. 1, Groups A, B, C, D
CSA/FM Class II, Div. 1, Groups E, F, G
CSA/FM Class III T4

F
Explosion Proof Enclosure with IS Probe:
CSA/FM Class I, Div. 1, Groups A, B, C, D
CSA/FM Class II, Div. 1, Groups E, F, G
CSA/FM Class III T4

G
General Purpose (CSA, FM)

H
General Purpose (CSA, FM, CE, RCM)

J
Enclosure and Lid
Aluminum epoxy coated




A
B
C
D

0

1

2
1)
Barrier or Intrinsically Safe power supply required for Intrinsically Safe
protection
2)
Available with Probe version options A, B and, F ... K only
[ 1 000 mm (39.7 inch)]
 We can offer shorter delivery times for configurations designated with the
Quick Ship Symbol . For details see page 9/5 in the appendix.
Siemens FI 01 · 2016
Inspection Certificate Type 3.1 per EN 10204
See page 4/56

4/54
 C11
Note: The Operating Instructions should be
ordered as a separate line on the order.
This device is shipped with the Siemens Level and
Weighing manual DVD containing the ATEX Quick
Start and manual library.
Dust Ignition Proof:
CE, RCM, ATEX II 1/2 D, 2 D IP6X T100 °C
Active shield length
Standard length (125 mm threaded, 105 mm flanged)
Extended shield (250 mm threaded, 230 mm flanged)2)
Extended shield (400 mm threaded, 380 mm flanged)2)
Manufacturer's test certificate: M to DIN 55350,
Part 18 and to ISO 9000
Operating Instructions
Approvals
2 x ½" NPT via adapter - cable inlet, IP65
2 x M20 x 1.5 cable inlet, IP65
2 x ½" NPT via adapter - cable inlet, IP68
2 x M20 x 1.5 cable inlet, IP68
Order code
© Siemens AG 2016
Level Measurement
Point level measurement - RF Capacitance switches
Pointek CLS300 - Digital
Selection and Ordering data
Article No.
Selection and Ordering data
Article No.
Pointek CLS300 - Digital - High Temperature
Rod version with Threaded or Flanged process
connection
Inverse frequency shift capacitance level and
material detection switch with optional rod/cable
choices and configurable output. It is ideal for
detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure
and temperatures are present and has the ability to
tune out buildup on the probe.
7ML5662-
Pointek CLS300 - Digital - High Temperature
Rod version with Threaded or Flanged process
connection
Inverse frequency shift capacitance level and
material detection switch with optional rod/cable
choices and configurable output. It is ideal for
detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure
and temperatures are present and has the ability to
tune out buildup on the probe.
7ML5662-
77 7 0 7 - 77 77
Click on the Article No. for the online configuration in the PIA Life Cycle Portal.
Add Order code Y01 and plain text:
"Insertion length ... mm"
Extended rod, factory adjusted length
250 ... 499 mm (9.8 ... 19.65 inch)
Extended rod, factory adjusted length
500 ... 749 mm (19.69 ... 29.49 inch)
Process connection
Threaded, 316L stainless steel
¾" NPT [(Taper), ANSI/ASME B1.20.1]
1" NPT [(Taper), ANSI/ASME B1.20.1]
1¼" NPT [(Taper), ANSI/ASME B1.20.1]
 0A
 0B
 0C
1½" NPT [(Taper), ANSI/ASME B1.20.1]
R ¾" [(BSPT), EN 10226/PT (JIS-T), JIS B 0203]
R 1" [(BSPT), EN 10226/PT (JIS-T), JIS B 0203]
 0D
 1A
 1B
R 1½" [(BSPT), EN 10226/PT (JIS-T),
JIS B 0203]
G ¾" [(BSPP), EN ISO 228-1/PF (JIS-P),
JIS B 0202]
G 1" [(BSPP), EN ISO 228-1/PF (JIS-P),
JIS B 0202]
 1D
G 1½" [(BSPP), EN ISO 228-1/PF (JIS-P),
JIS B 0202]
Extended rod, factory adjusted length
750 ... 999 mm (29.53 ... 39.3 inch)
3A
 3D
Welded flange, 316L stainless steel, raised face
1" ASME, 150 lb
1" ASME, 300 lb
1" ASME, 600 lb
 5A
5B
5C
1½" ASME, 150 lb
1½" ASME, 300 lb
1½" ASME, 600 lb
 5D
5E
5F
2" ASME, 150 lb
2" ASME, 300 lb
2" ASME, 600 lb
 5G
5H
5J
3" ASME, 150 lb
3" ASME, 300 lb
3" ASME, 600 lb
 5K
5L
5M
4" ASME, 150 lb
4" ASME, 300 lb
4" ASME, 600 lb
 5N
5P
5Q
Welded flange, 316L stainless steel,
Type A flat faced
DN 25, PN 16
DN 25, PN 40
DN 40, PN 16
 6A
6B
 6C
DN 40, PN 40
DN 50, PN 16
DN 50, PN 40
6D
 6E
6F
DN 80, PN 16
DN 80, PN 40
DN 100, PN 16
DN 100, PN 40
(Note: Flange bolting patterns and facings
dimensionally correspond to the applicable
ASME B16.5 or EN 1092-1 standard.)
 6G
6H
 6J
6K
E

F

G

Probe material
316L stainless steel with ceramic (ZrO2) isolators

4
0
0

B

C

D

F

G


H
J
Enclosure and Lid
Aluminum epoxy coated
2 x ½" NPT via adapter - cable inlet, IP65
2 x M20 x 1.5 cable inlet, IP65
2 x ½" NPT via adapter - cable inlet, IP68
2 x M20 x 1.5 cable inlet, IP68
Active shield length
Standard length (125 mm threaded, 105 mm flanged)
Extended shield (250 mm threaded, 230 mm flanged)2)
Extended shield (400 mm threaded, 380 mm flanged)3)




A
B
C
D

0

1

2
1)
Barrier or Intrinsically Safe power supply required for Intrinsically Safe
protection
2)
Available with Probe version options B ... D, F, G only
[ 500 mm (19.69 inch)]
3)
Available with Probe version options C, D, and G only
[ 750 mm (29.53 inch)]
 We can offer shorter delivery times for configurations designated with the
Quick Ship Symbol . For details see page 9/5 in the appendix.
Probe length (length from flange face)
(threaded lengths include process thread)
Note: No Y01 needed in Order code for
standard lengths
Standard version rod, 350 mm (13.78 inch)
Extended rod, length 500 mm (19.69 inch)
Extended rod, length 750 mm (29.53 inch)
Extended rod, length 1 000 mm (39.37 inch)

Wetted seals
Graphite
Approvals
Dust Ignition Proof:
CE, RCM, ATEX II 1/2 D, 2 D IP6X T100 °C
Intrinsically Safe1)
CE, RCM, ATEX II 1 G EEx ia IIC T6 ... T4,
ATEX II 1/2 D, 2 D IP6X T100 °C
Flameproof Enclosure with IS Probe:
CE, RCM, ATEX II 1/2 G EEx d[ia] IIC T6 ... T4,
ATEX II 1/2 D T100 °C
Intrinsically Safe1)
CSA/FM Class I, Div. 1, Groups A, B, C, D
CSA/FM Class II, Div. 1, Groups E, F, G
CSA/FM Class III T4
Explosion Proof Enclosure with IS Probe:
CSA/FM Class I, Div. 1, Groups A, B, C, D
CSA/FM Class II, Div. 1, Groups E, F, G
CSA/FM Class III T4
General Purpose (CSA, FM)
General Purpose (CSA, FM, CE, RCM)
 3B
7 7 7 0 7 - 77 7 7




A
B
C
D
Siemens FI 01 · 2016
4/55
© Siemens AG 2016
Level Measurement
Point level measurement - RF Capacitance switches
Pointek CLS300 – Standard and Digital
Selection and Ordering data
Order code
Article No.
Operating Instructions - Standard
Please add "-Z" to Article No. and specify Order
code(s).
English
7ML1998-5JH04
German
Note: The Operating Instructions should be
ordered as a separate line on the order.
All literature is available to download for free, in a
range of languages, at http://www.siemens.com/
processinstrumentation/documentation
7ML1998-5JH34
Total insertion length: enter the total insertion length  Y01
in plain text description
Stainless steel tag [69 x 50 mm (2.71 x 1.97 inch)]:  Y15
Measuring-point number/identification
(max. 27 characters) specify in plain text
Manufacturer's test certificate: M to DIN 55350,
Part 18 and to ISO 9000
 C11
Inspection Certificate Type 3.1 per EN 10204
 C12
This device is shipped with the Siemens Level and
Weighing manual DVD containing the ATEX Quick
Start and Operating Instructions library.
Operating Instructions - Digital
Operating Instructions
4
Selection and Ordering data
Further designs
Note: The Operating Instructions should be
ordered as a separate line on the order.
This device is shipped with the Siemens Level and
Weighing manual DVD containing the ATEX Quick
Start and manual library.
See page 4/56
Accessories
See page 4/56
 We can offer shorter delivery times for configurations designated with the
Quick Ship Symbol . For details see page 9/5 in the appendix.
English
7ML1998-5JJ05
German
Note: The Operating Instructions should be
ordered as a separate line on the order.
All literature is available to download for free, in a
range of languages, at http://www.siemens.com/
processinstrumentation/documentation
7ML1998-5JJ34
This device is shipped with the Siemens Level and
Weighing manual DVD containing the ATEX Quick
Start and Operating Instructions library.
Accessories
One metallic cable gland M20 x 1.5, -40 ... +80 °C
(-40 ... +176 °F) with integrated shield connection
(available for PROFIBUS PA)
7ML1930-1AQ
General Purpose
1/2" NPT General Purpose Cable Entry IP68/IP69K
NEMA6, -40 ... +100 °C (-40 ... +212 °F), cable size
6 ... 12 mm (0.236 ... 0.472 inch)
7ML1830-1JA
M20 x 1.5 General Purpose Cable Entry IP68/IP69K
NEMA6, -40 ... +100 °C (-40 ... +212 °F), cable size
7 ... 12 mm (0.275 ... 0.472 inch)
7ML1830-1JC
Hazardous Locations
1/2" NPT EMC rated Cable Gland: Dust Ignition Proof,
Flameproof Exd, and Increased Safety ATEX II 2 GD
ExtD A21 (Zone 1, Zone 2, Zone 21, Zone 22, and in
Gas Groups IIA,IIB and IIC) -60 ... +80 °C IP66, IP67,
IP68, NEMA4X, cable sizes 5.5 ... 12 mm
(0.216 ... 0.472 inch)
7ML1830-1JB
M20 EMC rated Cable Gland: Dust Ignition Proof,
Flameproof Exd, and Increased Safety ATEX II 2 GD
ExtD A21 (Zone 1, Zone 2, Zone 21, Zone 22, and in
Gas Groups IIA,IIB and IIC) -60 ... +80 °C IP66, IP67,
IP68, NEMA4X, cable sizes 5.5 ... 12 mm
(0.216 ... 0.472 inch)
7ML1830-1JD
Blind threaded flanges are available.
Customers interested in a custom designed device
should consult a local sales person. For more
information, please visit
http://www.automation.siemens.com/aspa_app.
Pointek Specials
4/56
Siemens FI 01 · 2016
See page 4/79
© Siemens AG 2016
Level Measurement
Point level measurement - RF Capacitance switches
Pointek CLS300 – Standard and Digital
■ Characteristic curves
Pressure/temperature curve
CLS300 extended rod and cable probes
Threaded process connections
(7ML5650, 7ML5651, 7ML5660 and 7ML5661)
Permitted operating pressures P
40 bar (580 psi)
30 bar (435 psi)
20 bar (290 psi)
Atmospheric
-40 ºF 14 ºF
(-40 ºC) (-10 ºC)
-1 bar (-14.5 psi)
-150 ºC
(-238 ºF)
4
10 bar (145 psi)
-100 ºC -50 ºC
(-148 ºF) (-58 ºF)
100 ºF
(38 ºC)
0 ºC RT 50 ºC
(32 ºF)
(122 ºF)
200 ºF
(93 ºC)
100 ºC
(212 ºF)
300 ºF
(149 ºC)
150 ºC
(302 ºF)
400 ºF
(204 ºC)
200 ºC
(392 ºF)
500 ºF
(260 ºC)
250 ºC
(482 ºF)
-29 ºC
(-20 ºF)
600 ºF
(315 ºC)
300 ºC
(572 ºF)
700 ºF
(371 ºC)
350 ºC
400 ºC
(662 ºF) (752 ºF)
Permitted operating temperature T
Example:
Permitted operating pressure = 30 bar (435 psi) at 75 °C
Pointek CLS300 process pressure/temperature derating curves (7ML5650, 7ML5651, 7ML5660 and 7ML5661)
Pressure/temperature curve
CLS300 high temperature rod probes
Threaded process connections
(7ML5652 and 7ML5662)
Permitted operating pressures P
40 bar (580 psi)
30 bar (435 psi)
20 bar (290 psi)
Atmospheric
10 bar (145 psi)
-40 ºF 14 ºF
(-40 ºC) (-10 ºC)
-1 bar (-14.5 psi)
-150 ºC
(-238 ºF)
-100 ºC -50 ºC
(-148 ºF) (-58 ºF)
100 ºF
(38 ºC)
0 ºC RT 50 ºC
(32 ºF)
(122 ºF)
200 ºF
(93 ºC)
100 ºC
(212 ºF)
300 ºF
(149 ºC)
150 ºC
(302 ºF)
-29 ºC
(-20 ºF)
400 ºF
(204 ºC)
200 ºC
(392 ºF)
500 ºF
(260 ºC)
250 ºC
(482 ºF)
600 ºF
(315 ºC)
300 ºC
(572 ºF)
700 ºF
(371 ºC)
350 ºC
400 ºC
(662 ºF) (752 ºF)
Permitted operating temperature T
Pointek CLS300 process pressure/temperature derating curves (7ML5652 and 7ML5662)
Siemens FI 01 · 2016
4/57
© Siemens AG 2016
Level Measurement
Point level measurement - RF Capacitance switches
Pointek CLS300 – Standard and Digital
Pressure/temperature curve
CLS300 extended rod and cable probes
ASME flanged process connections
(7ML5650, 7ML5651, 7ML5660 and 7ML5661)
Permitted operating pressures P
50 bar (725 psi)
40 bar (580 psi)
30 bar (435 psi)
4
ASME 300 lb1)
20 bar (290 psi)
-40 ºF 14 ºF
(-40 ºC) (-10 ºC)
-1 bar (-14.5 psi)
-150 ºC
(-238 ºF)
ASME 150 lb1)
10 bar (145 psi)
Atmospheric
-100 ºC -50 ºC
(-148 ºF) (-58 ºF)
100 ºF
(38 ºC)
0 ºC RT 50 ºC
(32 ºF)
(122 ºF)
200 ºF
(93 ºC)
100 ºC
(212 ºF)
300 ºF
(149 ºC)
150 ºC
(302 ºF)
400 ºF
(204 ºC)
200 ºC
(392 ºF)
500 ºF
(260 ºC)
250 ºC
(482 ºF)
-29 ºC
(-20 ºF)
1)
600 ºF
(315 ºC)
300 ºC
(572 ºF)
700 ºF
(371 ºC)
350 ºC
400 ºC
(662 ºF) (752 ºF)
Permitted operating temperature T
The curve denotes the minimum allowable flange class for the shaded area below.
Pointek CLS300 process pressure/temperature derating curves (7ML5650, 7ML5651, 7ML5660, and 7ML5661)
Permitted operating pressures P
Pressure/temperature curve
CLS300 high temperature rod probes
ASME flanged process connections
(7ML5652 and 7ML5662)
90 bar (1.305 psi)
80 bar (1.160 psi)
70 bar (1.015 psi)
60 bar (870 psi)
ASME 600 lb1)
50 bar (725 psi)
40 bar (580 psi)
30 bar (435 psi)
ASME 300 lb1)
20 bar (290 psi)
ASME 150 lb1)
10 bar (145 psi)
Atmospheric
-40 ºF 14 ºF
(-40 ºC) (-10 ºC)
-1 bar (-14.5 psi)
-150 ºC
(-238 ºF)
-100 ºC -50 ºC
(-148 ºF) (-58 ºF)
100 ºF
(38 ºC)
0 ºC RT 50 ºC
(32 ºF)
(122 ºF)
200 ºF
(93 ºC)
100 ºC
(212 ºF)
300 ºF
(149 ºC)
150 ºC
(302 ºF)
-29 ºC
(-20 ºF)
1)
The curve denotes the minimum allowable flange class for the shaded area below.
Pointek CLS300 process pressure/temperature derating curves (7ML5652 and 7ML5662)
4/58
Siemens FI 01 · 2016
400 ºF
(204 ºC)
200 ºC
(392 ºF)
500 ºF
(260 ºC)
250 ºC
(482 ºF)
600 ºF
(315 ºC)
300 ºC
(572 ºF)
700 ºF
(371 ºC)
350 ºC
400 ºC
(662 ºF) (752 ºF)
Permitted operating temperature T
© Siemens AG 2016
Level Measurement
Point level measurement - RF Capacitance switches
Pointek CLS300 – Standard and Digital
Pressure/temperature curve
CLS300 extended rod and cable probes
EN flanged process connections
(7ML5650, 7ML5651, 7ML5660 and 7ML5661)
Permitted operating pressures P
50 bar (725 psi)
40 bar (580 psi)
30 bar (435 psi)
PN 401)
4
20 bar (290 psi)
Atmospheric
-40 ºF 14 ºF
(-40 ºC) (-10 ºC)
-1 bar (-14.5 psi)
-150 ºC
(-238 ºF)
PN 161)
10 bar (145 psi)
-100 ºC -50 ºC
(-148 ºF) (-58 ºF)
100 ºF
(38 ºC)
0 ºC RT 50 ºC
(32 ºF)
(122 ºF)
200 ºF
(93 ºC)
100 ºC
(212 ºF)
300 ºF
(149 ºC)
150 ºC
(302 ºF)
400 ºF
(204 ºC)
200 ºC
(392 ºF)
500 ºF
(260 ºC)
250 ºC
(482 ºF)
300 ºC
(572 ºF)
-29 ºC
(-20 ºF)
1)
600 ºF
(315 ºC)
700 ºF
(371 ºC)
350 ºC
400 ºC
(662 ºF) (752 ºF)
Permitted operating temperature T
The curve denotes the minimum allowable flange class for the shaded area below.
Pointek CLS300 process pressure/temperature derating curves (7ML5650, 7ML5651, 7ML5660 and 7ML5661)
Pressure/Temperature Curve
CLS300 High Temperature Rod Probes
EN Flanged Process Connections (7ML5652 and 7ML5662)
Permitted Operating Pressures P
50 bar (725 psi)
40 bar (580 psi)
30 bar (435 psi)
PN 401)
20 bar (290 psi)
Atmospheric
-40 ºF 14 ºF
(-40 ºC) (-10 ºC)
-1 bar (-14.5 psi)
-150 ºC
(-238 ºF)
PN 161)
10 bar (145 psi)
-100 ºC -50 ºC
(-148 ºF) (-58 ºF)
100 ºF
(38 ºC)
0 ºC RT 50 ºC
(32 ºF)
(122 ºF)
200 ºF
(93 ºC)
100 ºC
(212 ºF)
300 ºF
(149 ºC)
150 ºC
(302 ºF)
-29 ºC
(-20 ºF)
1)
400 ºF
(204 ºC)
200 ºC
(392 ºF)
500 ºF
(260 ºC)
250 ºC
(482 ºF)
600 ºF
(315 ºC)
300 ºC
(572 ºF)
700 ºF
(371 ºC)
350 ºC
400 ºC
(662 ºF) (752 ºF)
Permitted Operating Temperature T
The curve denotes the minimum allowable flange class for the shaded area below.
Pointek CLS300 process pressure/temperature derating curves (7ML5652 and 7ML5662)
Siemens FI 01 · 2016
4/59
© Siemens AG 2016
Level Measurement
Point level measurement - RF Capacitance switches
Pointek CLS300 – Standard and Digital
■ Dimensional drawings
Rod version
Threaded (7ML5650 and 7ML5660)
Lid
Thermal
isolator
Ø32 (1.26)
Stainless
steel weight
Y01 (insertion length)
min. = 500 (20)/max. = 25 000 (984)
Y02 1)
Ø10 (0.35)
Ø32 (1.26)
Note:
1)
Extended Active Shield (Y02): standard length 125 (4.92). Optional active shield lengths: 250 (9.84) or 400 (15.75).
Pointek CLS300 threaded process connections, dimensions in mm (inch)
4/60
Siemens FI 01 · 2016
Thermal
isolator
247 (9.72)
Y02 1)
PFA insulated
cable
250 (9.84)
Y02
250 (9.84)
Ø6 (0.24)
Measuring length
Stainless
steel cable
Y01 (insertion length)
min. = 500 (20)/max. = 25 000 (984)
1)
Cable version, insulated
Threaded (7ML5651 and 7ML5661)
240 (9.45)
XP, lid without window
146
(5.75)
234 (9.21)
159 (6.26)
GP, DIP lid,
without window
Ø19 (0.75)
Cable version, non-insulated
Threaded (7ML5651 and 7ML5661)
Stainless
steel weight
Y01 (insertion length)
min. = 250 (9.8)/max. = 1 000 (39.37)
Probe
Lid with window
Measuring length
Ø19 (0.75)
Ceramic
isolator(s)
M20: 135 (5.32)
½" NPT: 150 (5.91)
Measuring length
Y01 (insertion length)
min. = 250 (9.8)/max. = 1 000 (39.37)
Y02 1)
Probe
Measuring length
4
2 cable entries
½" NPT or
M20 x 1.5
20 (0.79)
152 (5.98)
Lid clip
Electronics/
enclosure
High temperature rod version
Threaded (7ML5652 and 7ML5662)
© Siemens AG 2016
Level Measurement
Point level measurement - RF Capacitance switches
Pointek CLS300 – Standard and Digital
Rod version
Welded flange (7ML5650 and 7ML5660)
High temperature rod version
Welded flange
(7ML5652 and 7ML5662)
2 cable entries
½" NPT or
M20 x 1.5
Lid
Lid clip
M20: 135 (5.32)
½" NPT: 150 (5.91)
Ø 19 (0.75)
Cable version, insulated
Welded flange (7ML5651 and 7ML5661)
270 (10.63)
263 (10.35)
Flange Facing (raised face)
Facing thickness
ASME 150/300
2 (0.08)
ASME 600/900
7 (0.28)
PN16/40
2 (0.08)
Y02
Stainless
steel weight
Measuring length
Ø 10 (0.35)
Y01 (insertion length)
min. = 500 (20)/max. = 25 000 (984)
1)
PFA insulated
cable
250 (9.84)
250 (9.84)
Ø 6 (0.24)
Y01 (insertion length)
min. = 500 (20)/max. = 25 000 (984)
Stainless
steel cable
Measuring length
Y02 1)
Flange Class
Ø 32 (1.26)
Thermal
isolator
Ø 19 (0.75)
Cable version, non-insulated
Welded flange (7ML5651 and 7ML5661)
Stainless
steel weight
257 (10.12)
XP, lid without window
168
(6.61)
181 (7.13)
GP, DIP lid,
without window
174 (6.85)
Y01 (insertion length)
min. = 250 (9.8)/max. = 1 000 (39.37)
Probe
Y02 1)
Ceramic
isolator(s)
Measuring length
Probe
Lid with window
Thermal
isolator
Y01 (insertion length)
min. = 250 (9.8)/max. = 1 000 (39.37)
Measuring length
Y02 1)
Electronics/
enclosure
Ø 32 (1.26)
Note:
1)
Extended Active Shield (Y02): standard length 105 (4.13). Optional active shield lengths: 230 (9.06) or 380 (14.96).
Insertion length does not include any raised face/gasket face dimension (see Flange Facing Table above)
Pointek CLS300 flanged process connections, dimensions in mm (inch)
Siemens FI 01 · 2016
4/61
4
© Siemens AG 2016
Level Measurement
Point level measurement - RF Capacitance switches
Pointek CLS300 – Standard and Digital
■ Schematics
Wiring: Pointek CLS300 standard
White
Black
Red
P2
(f )
(+)
Switch bank
Trip
point
S1
P1
K1
OFF
GND
3
+
Delay
2
1
Sensor
L1
L3
Sensor
status
L2
Power
on
1
2
3
Power
supply
12 to 250 V AC/DC
Output
status
4
K4
NC
NO
NO
K3
K2
Solid state switch:
30 V DC/30 V AC
(peak),
82 mA max.
Relay contact:
8 A at 250 V AC, 2 000 VA
5 A at 30 V DC, 150 W
Notes:
- Identification label is on underside of lid. Switch and potentiometer settings
are for illustration purposes only (refer to operation/setup in manual).
- All field wiring must have insulation suitable for at least 250 V.
- Relay contact terminals are for use with equipment having no accessible live
parts and wiring having insulation suitable for at least 250 V.
- Maximum working voltage between adjacent relay contacts shall be 250 V.
- Refer to the Instruction manual or contact Siemens representative for detailed
wiring information.
Wiring: Pointek CLS300 digital
White
Test input
Reed
contact*
White
Red (+)
Black (-)
Sensor
Alarm output
solid-state switch
Orange (f)
24 V DC/PROFIBUS PA
Power connection:
24 V DC or PROFIBUS PA bus
(not polarity sensitive).
Notes:
Refer to the instruction manual or contact a Siemens representative
for detailed wiring information.
*Magnet activated sensor test
A magnet can be used to test the sensor without opening the lid of the
Pointek CLS300 digital version. Bring the magnet close to the test area
indicated on the enclosure. The sensor test starts and finishes
automatically after 10 seconds.
Pointek CLS300 connections
4/62
Siemens FI 01 · 2016
© Siemens AG 2016
Level Measurement
Point level measurement - RF Capacitance switches
Pointek CLS Specials
■ Selection and ordering data
Pointek Specials1)
Pointek Specials1)
Article No.
Article No.
Kit, sensor for cable units, PPS, digital,
FKM
A5E01163678
Kit, sensor for cable units, PPS, standard,
FFKM
A5E01163679
Kit, sensor for cable units, PPS, digital,
FFKM
A5E01163680
Kit, sensor for cable units, PVDF, standard,
FKM
A5E01163681
Kit, sensor for cable units, PVDF, digital,
FKM
A5E01163682
CLS100 Miscellaneous Parts
Custom length of cable is available only for
7ML5501-xxx1x and 7ML5501-xxx5x2)
Kit, sensor for cable units, PVDF, standard,
FFKM
A5E01163683
CLS200 Gasket (IP65), Synprene
Kit, sensor for cable units, PVDF, digital,
FFKM
A5E01163684
CLS100 Polycarbonate Lid and Gasket, FKM
Kit, Lid and gasket,
CLS100 enclosure version
A5E01163671
CLS200 Mounting Bracket,
316L stainless steel
Spare gasket, enclosure version
(IP65 versions only)
A5E01163672
CLS200 Gasket (IP68), Silicone
Spare mounting bracket
A5E01163685
CLS200 PROFIBUS Connector (IP65)
Spare gasket, enclosure version
(IP68 versions)
A5E01163673
Spare, PROFIBUS connector
(IP65 versions only)
CLS200 Blind Lid
A5E01163686
CLS200 Miscellaneous Parts
CLS200 with FFKM O-rings (any version)2)
CLS200 Electronics
Spare aluminum blind lid
(for standard versions only)
A5E01163674
CLS200 Lid with window
Test magnet, digital version
7ML1830-1JE
Amplifier/power supply kit, standard version
A5E03251681
Amplifier/power supply, digital version
7ML1830-1JF
LCD display, digital version
7ML1830-1JK
CLS300 Cable Extensions,
316L stainless steel
Spare aluminum lid with window
A5E01163676
CLS200 Sensor Kit for cable units
Kit, sensor for cable units, PPS, Standard, FKM
A5E01163677
Kit, stainless steel cable extension, 1 m,
adjustable by customer
A5E01163688
Kit, stainless steel cable extension, 3 m,
adjustable by customer
A5E01163689
Kit, stainless steel cable extension, 5 m,
adjustable by customer
A5E01163690
Kit, stainless steel cable extension, 10 m,
adjustable by customer
A5E01163691
Kit, stainless steel cable extension, 15 m,
adjustable by customer
A5E01163693
Kit, stainless steel cable extension, 20 m,
adjustable by customer
A5E01163695
Siemens FI 01 · 2016
4/79
4
© Siemens AG 2016
Level Measurement
Point level measurement - RF Capacitance switches
Pointek CLS Specials
Pointek Specials1)
Pointek Specials1)
Article No.
CLS300 Cable Extensions,
316 stainless steel with PFA coating
4
Article No.
CLS300 Electronics Kits with drivers
(for rod or cable versions)
Kit, PFA cable extension, 1 m,
adjustable by customer
A5E01163697
Kit, PFA cable extension, 3 m,
adjustable by customer
A5E01163698
Kit, PFA cable extension, 5 m,
adjustable by customer
A5E01163699
Kit, PFA cable extension, 10 m,
adjustable by customer
A5E01163700
Kit, PFA cable extension, 15 m,
adjustable by customer
A5E01163701
Kit, PFA cable extension, 20 m,
adjustable by customer
A5E01163702
CLS300 Rod Kits, 316L stainless steel
Kit, electronics with driver, standard CLS300.
To be used in rod or cable versions with
length less than 5 m.3)4)
A5E01163723
Kit, electronics with driver, digital CLS300.
To be used in rod or cable versions with
length less than 5 m.3)4)
A5E01163725
CLS300 Electronics Kits with drivers
(for cable versions)
Kit, electronics with driver, standard CLS300.
To be used in cable versions with
length greater than 5 m.3)4)
A5E01163724
Kit, electronics with driver, digital CLS300.
To be used in cable versions with
length greater than 5 m.3)4)
A5E01163726
CLS300 Electronics
Kit, stainless steel rod 180 mm (7.09 inch) to
be used with CLS300 units only (with standard
active shield). Insertion length after installation
is 350 mm (13.78 inch).
A5E01163719
Kit, stainless steel rod 330 mm (12.99 inch) to
be used with CLS300 units only (with standard
active shield). Insertion length after installation
is 500 mm (19.69 inch).
A5E01163720
Kit, stainless steel rod 580 mm (22.83 inch) to
be used with CLS300 units only (with standard
active shield). Insertion length after installation
is 750 mm (29.53 inch).
A5E01163721
Kit, stainless steel rod 830 mm (32.68 inch) to
be used with CLS300 units only (with standard
active shield). Insertion length after installation
is 1 000 mm (39.37 inch).
A5E01163722
Kit, stainless steel rod 1 330 mm (52.36 inch) to
be used with CLS300 units only (with standard
active shield). Insertion length after installation
is 1 500 mm (59.06 inch).2)
Kit, stainless steel rod 1 830 mm (72.05 inch) to
be used with CLS300 units only (with standard
active shield). Insertion length after installation
is 2 000 mm (78.74 inch).2)
Test magnet, digital version
7ML1830-1JE
Amplifier/power supply kit, standard version
A5E03251683
Amplifier/power supply, digital version
7ML1830-1JF
LCD display, digital version
7ML1830-1JK
CLS300 Weight Kit, 316L stainless steel
Kit, spare stainless steel weight. To be used in
any cable version of CLS300
A5E01163727
CLS500 Gasket (IP65), Silicone
Spare gasket, CLS500 enclosure version, IP65
A5E01163728
CLS500 Blind Lid
Spare CLS500 aluminum blind lid
A5E01163729
Kit, stainless steel rod customized length
up to 1 m2)
CLS500 Electronics Kit
Kit, stainless steel rod customized length
up to 2 m2)
1)
Special flange sizes and facings are available. Please consult a local sales
person for details.
2)
Please consult a local sales person for part number and pricing
3)
For General Purpose approvals only
4)
To maintain approvals, qualified trained Siemens personnel
required for part replacement
Transmitter, MSP 2002-1, 330 PF
7ML1830-1JP
Customers interested in a custom designed device should consult a local
sales person. For more information, please visit
http://www.automation.siemens.com/aspa_app.
4/80
Siemens FI 01 · 2016