Datasheet

PHOTOSENSOR MODULES
H9306/H9307 SERIES
OVERVIEW
The H9306/H9307 series voltage output type photosensor modules
contain a high-voltage power supply circuit, low noise amplifier and
13-mm(1/2") diameter side-on photomultiplier tube. The amplifier
contained in H9306 series has 1 V/µA of current to voltage conversion
factor and 20 kHz of frequency bandwidth. The amplifier contained in
H9307 series has 0.1V/µA of current to voltage conversion factor and
200 kHz of frequency bandwidth.
PRODUCT VARIATIONS
Type No.
H9306-01
H9306-02
H9306-03
H9306-13
H9306-04
H9306-05
Spectral response
185 nm to 750 nm
185 nm to 900 nm
185 nm to 900 nm
185 nm to 900 nm
185 nm to 830 nm
185 nm to 650 nm
Photocathode
Bialkali
Multialkali
Multialkali
Multialkali
Multialkali
Bialkali
Window material Current-to-voltage conversion factor Frequency bandwidth
UV glass
UV glass
UV glass
1 V/µA
DC to 20 kHz
UV glass
UV glass
UV glass
Type No.
H9307-01
H9307-02
H9307-03
H9307-13
H9307-04
H9307-05
Spectral response
185 nm to 750 nm
185 nm to 900 nm
185 nm to 900 nm
185 nm to 900 nm
185 nm to 830 nm
185 nm to 650 nm
Photocathode
Bialkali
Multialkali
Multialkali
Multialkali
Multialkali
Bialkali
Window material Current-to-voltage conversion factor Frequency bandwidth
UV glass
UV glass
UV glass
0.1 V/µA
DC to 200 kHz
UV glass
UV glass
UV glass
This product can't be used at vacuum environment or reduced pressure environment. Please pay attention when the H9306/H9307 series is used for
measuring the light below 190 nm.
Figure 1: Typical spectral response
1
0.1
1
-05
0.01
0.1
0.01
100
200
300
400
500
600
700
WAVELENGTH (nm)
800
0.001
900
ANODE RADIANT SENSITIVITY (V/nW)
-01
10
(H9306)
100
PMT GAIN: 105 (H9307)
10
TPMOB0116ED
-13
1
10
-03
1
0.1
-02
-04
0.01
0.1
0.01
100
200
300
400
500
600
700
800
ANODE RADIANT SENSITIVITY (V/nW)
PMT GAIN: 105 (H9307)
10
TPMOB0154EA
ANODE RADIANT SENSITIVITY (V/nW)
ANODE RADIANT SENSITIVITY (V/nW)
(H9306)
100
0.001
900
WAVELENGTH (nm)
Subject to local technical requirements and regulations, availability of products included in this promotional material may vary. Please consult with our sales office.
Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications are
subject to change without notice. No patent rights are granted to any of the circuits described herein. ©2015 Hamamatsu Photonics K.K.
PHOTOSENSOR MODULES H9306/H9307 SERIES
Figure 2: Schematic diagram
AMP
SIGNAL OUTPUT (VOLTAGE OUTPUT)
LOW VOLTAGE INPUT (+15 V)
LOW VOLTAGE INPUT (-15 V)
GND
Vref OUTPUT (+1.2 V)
Vcont INPUT (+0.25 V to +1.0 V)
(INPUT IMPEDANCE: 1 MΩ)
HIGH VOLTAGE
POWER SUPPLY
CIRCUIT
SPECIFICATIONS
Cathode
Parameter
Suffix
Input voltage
Max. input voltage
Max. input current *1
Max. control voltage
Recommended control voltage adjustment range
Effective area
Peak sensitivity wavelength
Min.
Luminous sensitivity
Typ.
Blue sensitivity index (CS 5-58) Typ.
Typ.
Red/White ratio
Typ.
Radiant sensitivity *2
Typ.
Offset voltage
Ripple noise *3 *4 (peak to peak) Max.
Max.
Settling time *5
Operating ambient temperature *6
Storage temperature *6
Weight
-01
420
80
120
10
—
90
Parameter
Suffix
Min.
Typ.
Radiant sensitivity *2 *3
Typ.
Voltage output due to PMT Typ.
dark current *3 *7
Max.
Max. output signal voltage
Current-to-voltage conversion factor
Anode
Luminous sensitivity *3
-01
1.0 × 108
7.0 × 108
520
1
10
Parameter
Suffix
Min.
Typ.
Radiant sensitivity *2 *3
Typ.
Voltage output due to PMT Typ.
dark current *3 *7
Max.
Max. output signal voltage
Current-to-voltage conversion factor
Anode
Luminous sensitivity *3
-01
1.0 × 107
7.0 × 107
52
0.1
1
H9306/H9307 Series
-03
-13
-04
±11.5 to ± 15.5
±18
+9/-1 (H9306), +15/-8 (H9307)
+1.2 (Input impedance: 1 MΩ)
+0.25 to +1.0 (Input impedance: 1 MΩ)
3.7 × 13.0
400
450
530
450
200
350
620
140
300
650
200
500
—
—
15
—
0.3
0.4
0.43
0.15
77
105
109
70
±3
0.8
10
+5 to +50
-20 to +50
110
-02
H9306 Series (with internal 20 kHZ amp)
-02
-03
-13
-04
4.0 × 108
4.0 × 108
3.0 × 108
1.0 × 109
1.2 × 109
2.0 × 109
2.6 × 109
7.0 × 108
310
420
430
250
1
2
3
0.1
10
10
10
1
+10 (Load resistance 10 kΩ)
1
H9307 Series (with internal 200 kHZ amp)
-02
-03
-13
-04
4.0 × 107
4.0 × 107
3.0 × 107
1.0 × 108
1.2 × 108
2.0 × 108
2.6 × 108
7.0 × 107
31
42
43
25
0.1
0.2
0.3
0.01
1
1
1
0.1
+1 (Load resistance 10 kΩ)
0.1
*1: Input voltage = +15 V, Control voltage = +1.0 V, Dark current output
*2: Measured at the peak sensitivity wavelength
*3: Control voltage = +1.0 V
*4: Cable RG-174/U, Cable length 450 mm, Load resistance = 1 MΩ, Load capacitance = 22 pF
*5: The time required for the output to reach a stable level following a change in the control voltage from +1.0 V to +0.5 V.
*6: No condensation
*7: After 30 minutes storage in darkness
-05
340
20
40
5
—
48
-05
5.0 × 107
3.0 × 108
360
0.5
5
(at +25 °C)
Unit
—
V
V
mA
V
V
mm
nm
µA/lm
—
—
mA/W
mV
mV
s
°C
°C
g
Unit
—
V/lm
V/nW
mV
V
V/µA
-05
5.0 × 106
3.0 × 107
36
0.05
0.5
Unit
—
V/lm
V/nW
mV
V
V/µA
Figure 3: Sensitivity adjustment method
Figure 4: Gain
VOLTAGE PROGRAMMING
108
PHOTOSENSOR MODULE
TPMOB0240EB
POWER SUPPLY
SIGNAL OUTPUT
COAXIAL CABLE
RED (LOW VOLTAGE INPUT)
GREEN (LOW VOLTAGE INPUT)
BLACK (GND)
BLUE (Vref OUTPUT)
WHITE (Vcontrol INPUT)
+15 V
-15 V
GND
107
-02/-03/-13
-01
106
+0.25 V to
+1.0 V
-05
PMT GAIN
• Adjust the control voltage to
adjust the sensitivity.
• Electrically insulate the
reference voltage output.
GND
RESISTANCE PROGRAMMING
PHOTOSENSOR MODULE
105
-04
104
POWER SUPPLY
SIGNAL OUTPUT
+15 V
-15 V
GND
103
CW
COAXIAL CABLE
RED (LOW VOLTAGE INPUT)
GREEN (LOW VOLTAGE INPUT)
BLACK (GND)
BLUE (Vref OUTPUT)
WHITE (Vcontrol INPUT)
102
0.25 0.3
MONITOR
POTENTIOMETER (10 kΩ)
When using a potentiometer, adjust sensitivity
while monitoring the control voltage. So it does not
exceed +1.2 V.
0.5
0.6
0.7 0.8 0.9 1.0 1.1 1.2
CONTROL VOLTAGE (V)
TPMOC0147EC
Figure 6: Ripple noise
Figure 5: Frequency characteristics
5
0.4
TPMOB0266EA
TPMOB0267EA
LOAD RESISTANCE: 1 MΩ
H9307
OUTPUT (1 mV/div.)
0
GAIN (dB)
-3
-5
-10
H9306
-15
-20
0.1
1
10
100
1000
FREQUENCY (kHz)
1 (µs/div.)
Figure 7: Output characteristics
●H9306
●H9307
TPMOB0268EA
TPMOB0269EA
LOAD RESISTANCE: 1 MΩ
LOAD RESISTANCE: 1 MΩ
OUTPUT SIGNAL
500 (mV/div.)
500 (mV/div.)
OUTPUT SIGNAL
INPUT LIGHT
20 (µs/div.)
INPUT LIGHT
2 (µs/div.)
PHOTOSENSOR MODULES H9306/H9307 SERIES
Figure 8: Dimensional outlines (Unit: mm)
8.8
WINDOW
(7 × 16)
PHOTOCATHODE
LOW VOLTAGE INPUT (+15 V) : AWG26 (RED)
LOW VOLTAGE INPUT (-15 V) : AWG26 (GREEN)
GND
: AWG26 (BLACK)
Vref OUTPUT (+1.2 V)
: AWG26 (BLUE)
Vcont INPUT (+0.25 V to +1.0 V): AWG26 (WHITE)
SIGNAL OUTPUT
: RG-174/U
53.2 ± 0.5
49.0 ± 0.5
19.7
2.1
19.0 ± 0.5
EFFECTIVE AREA
(3.7 × 13.0 MIN.)
11.7 ± 0.2
MOUNTING
THREADED HOLE
(4 × M2 DEPTH: 4)
450 ± 20
50.8 ± 0.5
FRONT VIEW
SIDE VIEW
TPMOA0013EI
9
DETAILS OF INPUT WINDOW
7
3.7
WINDOW
13
16
18
1.5
8.8
6.0
20.5
EFFECTIVE
AREA
(3.7 × 13.0 MIN.)
7
WINDOW
9
PHOTOCATHODE
TOP VIEW
FRONT VIEW
TPMOA0018EE
RELATED PRODUCT
POWER SUPPLY FOR PHOTOMULTIPLIER TUBE MODULES C7169
The C7169 is the power supply for photomultiplier tube modules which has
15 V input voltage.
This unit can provide both the driving voltage and the control voltage. This
feature enables users to operate the modules easily.
Parameter
Output voltage
Output current
Max.
Control voltage A (variable voltage range)
Terminal connection method
Input voltage
Operating ambient temperature
Dimensions (W × H × D) B
Weight
Description / Value
±15
0.3 (+15 V), 0.2 (-15 V)
+0.25 to +1.8
Binding post
AC100 to AC240
+5 to +50
147 × 61 × 200
Approx. 1.2
Unit
V
A
V
—
V
°C
mm
kg
NOTE: AAdjust within the recommended control voltage range for the photomultiplier tube
module being used.
BExcluding protuberance
HAMAMATSU PHOTONICS K.K.
www.hamamatsu.com
HAMAMATSU PHOTONICS K.K., Electron Tube Division
314-5, Shimokanzo, Iwata City, Shizuoka Pref., 438-0193, Japan, Telephone: (81)539/62-5248, Fax: (81)539/62-2205
U.S.A.: Hamamatsu Corporation: 360 Foothill Road, Bridgewater. N.J. 08807-0910, U.S.A., Telephone: (1)908-231-0960, Fax: (1)908-231-1218 E-mail: [email protected]
Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49)8152-375-0, Fax: (49)8152-2658 E-mail: [email protected]
France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: (33)1 69 53 71 00, Fax: (33)1 69 53 71 10 E-mail: [email protected]
United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44)1707-294888, Fax: (44)1707-325777 E-mail: [email protected]
North Europe: Hamamatsu Photonics Norden AB: Torshamnsgatan 35 SE-164 40 Kista, Sweden, Telephone: (46)8-509-031-00, Fax: (46)8-509-031-01 E-mail: [email protected]
TPMO1069E01
Italy: Hamamatsu Photonics Italia S.r.l.: Strada della Moia, 1 int. 6, 20020 Arese (Milano), Italy, Telephone: (39)02-93581733, Fax: (39)02-93581741 E-mail: [email protected]
SEPT. 2015. IP
China: Hamamatsu Photonics (China) Co., Ltd.: B1201 Jiaming Center, No.27 Dongsanhuan Beilu, Chaoyang District, Beijing 100020, China, Telephone: (86)10-6586-6006, Fax: (86)10-6586-2866 E-mail: [email protected]