LT3976 40V, 5A, 2MHz Step-Down Switching Regulator with 3.3µA Quiescent Current Features Description Ultralow Quiescent Current: 3.3µA IQ at 12VIN to 3.3VOUT n Low Ripple Burst Mode® Operation Output Ripple < 15mVP-P n Wide Input Range: Operation from 4.3V to 40V n5A Maximum Output Current n Excellent Start-Up and Dropout Performance n Adjustable Switching Frequency: 200kHz to 2MHz n Synchronizable Between 250kHz to 2MHz n Accurate Programmable Undervoltage Lockout n Low Shutdown Current: I = 700nA Q n Power Good Flag n Soft-Start Capability n Thermal Shutdown Protection n Current Limit Foldback with Soft-Start Override n Saturating Switch Design: 75mΩ On-Resistance n Small, Thermally Enhanced 16-Lead MSOP and 24-Lead 3mm × 5mm QFN Packages The LT®3976 is an adjustable frequency monolithic buck switching regulator that accepts a wide input voltage range up to 40V. Low quiescent current design consumes only 3.3µA of supply current while regulating with no load. Low ripple Burst Mode operation maintains high efficiency at low output currents while keeping the output ripple below 15mV in a typical application. The LT3976 can supply up to 5A of load current and has current limit foldback to limit power dissipation during short-circuit. A low dropout voltage of 500mV is maintained when the input voltage drops below the programmed output voltage, such as during automotive cold crank. n An internally compensated current mode topology is used for fast transient response and good loop stability. A high efficiency 75mΩ switch is included on the die along with a boost Schottky diode. An accurate 1.02V threshold enable pin can be driven directly from a microcontroller or used as a programmable undervoltage lockout. A capacitor on the SS pin provides a controlled inrush current (soft-start). A power good flag signals when VOUT reaches 91.6% of the programmed output voltage. The LT3976 is available in small 16-lead MSOP and 24-lead 3mm × 5mm QFN packages with exposed pad for low thermal resistance. Applications Automotive Battery Regulation Portable Products n Industrial Supplies n n L, LT, LTC, LTM, Linear Technology, the Linear logo and Burst Mode are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Typical Application No-Load Supply Current 3.3V Step-Down Converter 8 VIN 4.3V TO 40V IN REGULATION VOUT = 3.3V OFF ON EN VIN BOOST PG 10µF SW SS 10nF RT SYNC 130k f = 400kHz 3.3µH 0.47µF PDS540 LT3976 INPUT CURRENT (µA) 7 2Ω 470pF OUT FB GND VOUT 3.3V 5A 1M 10pF 576k 3976 TA01a 47µF 1210 ×2 6 5 4 3 2 1 0 0 5 10 15 20 25 30 INPUT VOLTAGE (V) 35 40 3976 G05 3976f For more information www.linear.com/3976 1 LT3976 Absolute Maximum Ratings (Note 1) VIN, EN Voltage (Note 3)............................................40V BOOST Pin Voltage....................................................55V BOOST Pin Above SW Pin..........................................30V FB, RT, SYNC, SS Voltage............................................6V PG Voltage.................................................................30V OUT Voltage...............................................................16V Operating Junction Temperature Range (Note 2) LT3976E.............................................. –40°C to 125°C LT3976I.............................................. –40°C to 125°C LT3976H............................................. –40°C to 150°C Storage Temperature Range................... –65°C to 150°C Lead Temperature (Soldering, 10 sec).................... 300°C Pin Configuration GND NC FB FB TOP VIEW 24 23 22 21 SS 1 TOP VIEW SYNC PG RT EN VIN VIN VIN NC 19 PG NC 3 18 RT BST 4 MSE PACKAGE 16-LEAD PLASTIC MSOP θJA = 40°C/W EXPOSED PAD (PIN 17) IS GND, MUST BE SOLDERED TO PCB 17 NC 25 GND NC 5 16 EN SW 6 15 VIN SW 7 14 VIN SW 8 13 VIN NC 9 10 11 12 NC 17 GND 16 15 14 13 12 11 10 9 NC 1 2 3 4 5 6 7 8 NC FB SS OUT BOOST SW SW SW NC 20 SYNC OUT 2 UDD PACKAGE 24-LEAD (3mm × 5mm) PLASTIC QFN θJA = 46°C/W EXPOSED PAD (PIN 25) IS GND, MUST BE SOLDERED TO PCB Order Information LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT3976EMSE#PBF LT3976EMSE#TRPBF 3976 16-Lead Plastic MSOP –40°C to 125°C LT3976IMSE#PBF LT3976IMSE#TRPBF 3976 16-Lead Plastic MSOP –40°C to 125°C LT3976HMSE#PBF LT3976HMSE#TRPBF 3976 16-Lead Plastic MSOP –40°C to 150°C LT3976EUDD#PBF LT3976EUDD#TRPBF LGHV 24-Lead (3mm × 5mm) Plastic QFN –40°C to 125°C LT3976IUDD#PBF LT3976IUDD#TRPBF LGHV 24-Lead (3mm × 5mm) Plastic QFN –40°C to 125°C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 3976f 2 For more information www.linear.com/3976 LT3976 Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. (Note 2) PARAMETER CONDITIONS Minimum Input Voltage (Note 3) Dropout Comparator Threshold (VIN – OUT) Falling MIN l 430 Dropout Comparator Threshold Hysteresis Quiescent Current from VIN FB Pin Current TYP MAX 4 4.3 V 500 570 mV 25 VEN Low VEN High, VSYNC Low VEN High, VSYNC Low 0.7 1.6 l VFB = 1.5V l Feedback Voltage l FB Voltage Line Regulation 4.3V < VIN < 40V (Note 3) Switching Frequency RT = 11.8k RT = 41.2k RT = 294k 1.183 1.173 1.8 0.8 160 UNITS mV 1.3 2.7 30 µA µA µA 0.1 12 nA 1.197 1.197 1.212 1.222 V V 0.0003 0.01 %/V 2.25 1 200 2.7 1.2 240 MHz MHz kHz Minimum Switch On-Time 120 Minimum Switch Off-Time (Note 4) 150 200 ns 10 12.5 A 7.5 ns Switch Current Limit VFB = 1V Foldback Switch Current Limit VFB = 0V 4.8 A Switch VCESAT ISW = 1A 80 mV Switch Leakage Current 0.02 1 μA Boost Schottky Forward Voltage ISH = 100mA 730 Boost Schottky Reverse Leakage VREVERSE = 12V 0.02 2 1.3 1.8 V 20 32 mA 1.02 1.12 Minimum Boost Voltage (Note 5) l BOOST Pin Current ISW = 1A, VBOOST – VSW = 3V EN Voltage Threshold EN Falling, VIN ≥ 4.3V l 0.92 mV EN Voltage Hysteresis 60 EN Pin Current 0.2 20 8.4 13 PG Threshold Offset from VFB VFB Falling 5 PG Hysteresis as % of Output Voltage VPG = 3V PG Sink Current VPG = 0.4V 0.02 l SYNC Low Threshold SS Source Current VSS = 0.5V Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LT3976E is guaranteed to meet performance specifications from 0°C to 125°C junction temperature. Specifications over the –40°C to 125°C operating junction temperature range are assured by design, characterization, and correlation with statistical process controls. The LT3976I is guaranteed over the full –40°C to 125°C operating junction % % 1 µA 480 μA 0.6 1.0 V 1.18 VSYNC = 6V nA 125 SYNC High Threshold SYNC Pin Current V mV 1.7 PG Leakage μA 1.5 0.1 0.9 1.8 V nA 2.6 μA temperature range. The LT3976H is guaranteed over the full –40°C to 150°C operating junction temperature range. High junction temperatures degrade operating lifetimes. Operating lifetime is derated at junction temperatures greater than 125°C. The junction temperature (TJ, in °C) is calculated from the ambient temperature (TA, in °C) and power dissipation (PD, in Watts) according to the formula: TJ = TA + (PD • θJA) where θJA (in °C/W) is the package thermal impedance. 3976f For more information www.linear.com/3976 3 LT3976 Electrical Characteristics Note 3: Minimum input voltage depends on application circuit. Note 4: The LT3976 contains circuitry that extends the maximum duty cycle if there is sufficient voltage across the boost capacitor. See the Application Information section for more details. Note 5: This is the minimum voltage across the boost capacitor needed to guarantee full saturation of the switch. Note 6: This IC includes overtemperature protection that is intended to protect the device during momentary overload conditions. Junction temperature will exceed the maximum operating junction temperature when overtemperature protection is active. Continuous operation above the specified maximum operating junction temperature may impair device reliability or permanently damage the device. Typical Performance Characteristics Efficiency at 3.3VOUT Efficiency at 5VOUT fSW = 800kHz VOUT = 5V 95 90 90 85 85 80 75 70 65 60 50 0.5 0 1 1.5 2 2.5 3 3.5 LOAD CURRENT (A) 4 4.5 90 80 75 70 65 50 0 0.5 1 1.5 2 2.5 3 3.5 LOAD CURRENT (A) 3976 G01 INPUT CURRENT (µA) EFFICIENCY (%) 70 60 50 40 30 12V 24V 36V 0 0.01 0.1 10 100 1 LOAD CURRENT (mA) 1000 10000 3976 G04 12V 24V 36V 0.1 10 100 1 LOAD CURRENT (mA) 1000 10000 3976 G03 No-Load Supply Current 10000 IN REGULATION VOUT = 3.3V 7 80 10 0 0.01 5 No-Load Supply Current 8 FRONT PAGE APPLICATION VOUT = 3.3V 20 30 10 6 INPUT CURRENT (µA) 90 4.5 50 40 3976 G02 Efficiency at 3.3VOUT 100 4 70 60 20 12V 24V 36V 55 5 fSW = 800kHz VOUT = 5V 80 60 12V 24V 36V 55 Efficiency at 5VOUT 100 FRONT PAGE APPLICATION VOUT = 3.3V 95 EFFICIENCY (%) EFFICIENCY (%) 100 EFFICIENCY (%) 100 TA = 25°C, unless otherwise noted. 5 4 3 2 FRONT PAGE APPLICATION VIN = 12V VOUT = 3.3V 1000 DUE TO CATCH DIODE LEAKAGE 100 10 1 0 0 5 10 15 20 25 30 INPUT VOLTAGE (V) 35 40 3976 G05 1 –55 –25 5 35 95 65 TEMPERATURE (°C) 125 155 3876 G06 3976f 4 For more information www.linear.com/3976 LT3976 Typical Performance Characteristics Reference Voltage Load Regulation 1.230 0.5 1.225 0.4 1.220 1.210 1.205 1.200 1.195 1.190 1.185 Line Regulation 0.05 VIN = 12V VOUT = 3.3V 0.3 0.03 0.2 0.1 0 –0.1 –0.2 1.175 –0.4 1.170 –55 –0.5 –25 65 35 5 95 TEMPERATURE (°C) 125 155 Thermal Derating –0.03 –0.04 0 1 3 2 LOAD CURRENT (A) 4 2 4 I-GRADE 2 9.0 8.5 8.0 7.0 150 125 10 CYCLE CURRENT LIMIT (A) 8 5 3 2 1 0 0.2 0.6 0.8 0.4 FB PIN VOLTAGE (V) 1.0 9 CURRENT LIMIT (A) 11 10 9 8 7 125 155 3976 G13 9 8 7 7 6 5 4 3 1.2 3976 G14 VFB = 1V VFB = 0V 3 1 1.0 30% DUTY CYCLE 4 2 0.6 0.8 0.4 FB PIN VOLTAGE (V) 1.0 5 1 0.2 0.8 6 2 0 0.4 0.6 DUTY CYCLE Soft-Start 10 8 0 0.2 3976 G12 30% DUTY CYCLE VSS = 3V 1.2 3976 G14 0 3976 G11 Current Limit Foldback 30% DUTY VSS = 3V 9 7 6 4 0 40 7.5 LIMITED BY MAXIMUM JUNCTION TEMPERATURE ΘJA = 40°C/W 3976 G10 10 65 35 95 5 TEMPERATURE (°C) H-GRADE 3 Switch Current Limit 6 –55 –25 35 9.5 12V 24V 36V 1 VOUT = 5V fSW = 400kHz 2.5in × 2.5in 4-LAYER BOARD 0 0 25 75 50 100 TEMPERATURE (°C) 150 30% DUTY CYCLE 25 20 15 30 INPUT VOLTAGE (V) Switch Current Limit CURRENT LIMIT (A) LIMITED BY MAXIMUM JUNCTION TEMPERATURE ΘJA = 40°C/W 10 10.0 CURRENT LIMIT (A) I-GRADE 125 5 3976 G09 5 H-GRADE 1 VOUT = 3.3V fSW = 400kHz 2.5in × 2.5in 4-LAYER BOARD 0 0 25 75 50 100 TEMPERATURE (°C) CURRENT LIMIT (A) –0.05 Thermal Derating LOAD CURRENT (A) LOAD CURRENT (A) 3 12 5 6 4 0 3976 G08 6 12V 24V 36V 0.01 –0.02 3976 G07 5 0.02 –0.01 –0.3 1.180 VOUT = 5V LOAD = 1A 0.04 CHANGE IN OUTPUT (%) 1.215 CHANGE IN OUTPUT (%) REFERENCE VOLTAGE (V) TA = 25°C, unless otherwise noted. 0 0 0.5 1.5 2.0 1.0 SS PIN VOLTAGE (V) 2.5 3976 G15 3976f For more information www.linear.com/3976 5 LT3976 Typical Performance Characteristics BOOST Pin Current Switch VCESAT BOOST PIN CURRENT (mA) 250 VCESAT (mV) 200 80 300 200 150 100 50 0 60 50 40 30 20 1 0 2 3 5 4 LOAD = 1A 120 100 0 1 3 2 SWITCH CURRENT (A) 200 LOAD = 5A 150 LOAD = 2.5A 125 LOAD = 1A 100 –55 –25 65 35 95 5 TEMPERATURE (°C) 125 300 720 660 600 540 480 250 200 150 100 50 65 35 95 5 TEMPERATURE (°C) 125 0 155 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2 2.2 SWITCHING FREQUENCY (MHz) 3976 G20 3976 G19 3976 G21 Internal Undervoltage Lockout (UVLO) Frequency Foldback 700 EN Thresholds 1.09 6 600 155 350 420 –55 –25 155 125 RT Programmed Switching Frequency RT RESISTOR (kΩ) SWITCHING FREQUENCY (kHz) 225 65 35 95 5 TEMPERATURE (°C) 3976 G18 780 VSYNC = 0V fSW = 2MHz 175 5 4 LOAD = 5A 60 –55 –25 Switching Frequency 250 LOAD = 2.5A 3976 G17 Minimum Off-Time MINIMUM OFF-TIME (ns) 140 80 3976 G16 EN RISING 1.08 5 400 300 200 EN THRESHOLD (V) 1.07 500 INPUT VOLTAGE (V) SWITCHING FREQUENCY (kHz) 160 10 0 VSYNC = 0V fSW = 2MHz 180 70 SWITCH CURRENT (A) 4 3 2 1.06 1.05 1.04 1.03 1 100 0 Minimum On-Time 90 MINIMUM ON-TIME (ns) 350 TA = 25°C, unless otherwise noted. 0 0.2 0.8 0.6 0.4 FB PIN VOLTAGE (V) 1 1.2 3976 G22 0 –55 –25 EN FALLING 1.02 65 35 95 5 TEMPERATURE (°C) 125 155 3976 G23 1.01 –55 –25 95 65 35 TEMPERATURE (°C) 5 125 155 3976 G24 3976f 6 For more information www.linear.com/3976 LT3976 Typical Performance Characteristics Minimum Input Voltage, VOUT = 3.3V Minimum Input Voltage, VOUT = 5V PG Thresholds 6.5 1.12 5.0 VOUT = 5V fSW = 800kHz 1.11 6.0 FB RISING 1.09 1.08 FB FALLING 1.07 1.06 VOUT = 3.3V FRONT PAGE APPLICATION 4.5 TO RUN/TO START INPUT VOLTAGE (V) INPUT VOLTAGE (V) 1.10 PG THRESHOLD (V) TA = 25°C, unless otherwise noted. 5.5 5.0 4.5 TO RUN/TO START 4.0 3.5 3.0 1.05 1.04 –55 –25 95 65 35 TEMPERATURE (°C) 5 125 4.0 155 1 0 3 2 LOAD CURRENT (A) 4 SS Pin Current Burst Frequency 2.4 140 2.2 120 VOUT = 3.3V fSW = 600kHz 400 300 200 VSS = 0.5V 2.0 1.8 1.6 1.4 1.2 100 20 40 60 80 100 120 140 160 LOAD CURRENT (mA) 1.0 –55 –25 95 65 35 TEMPERATURE (°C) 5 VBST = VIN 100 80 60 40 125 155 0 0 2 4 8 10 12 6 OUT PIN VOLTAGE (V) 3976 G29 3976 G28 Boost Diode Forward Voltage 14 16 3976 G30 Dropout Comparator Thresholds 600 1.6 580 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 5 20 DROPOUT THRESHOLD (mV) 0 BOOST DIODE VOLTAGE (V) 0 160 OUT PIN CURRENT (mA) 500 SS PIN CURRENT (µA) 800 600 4 Boost Capacitor Charger 2.6 VOUT = 5V fSW = 800kHz 3 2 LOAD CURRENT (A) 3976 G27 900 700 1 0 3976 G26 3976 G25 SWITCHING FREQUENCY (kHz) 2.5 5 560 540 VOUT RISING 520 500 480 VOUT FALLING 460 440 420 0 1 0.5 1.5 BOOST DIODE CURRENT (A) 2 400 –55 –25 3976 G31 65 35 5 95 TEMPERATURE (°C) 125 155 3976 G32 3976f For more information www.linear.com/3976 7 LT3976 Typical Performance Characteristics Start-Up/Dropout Performance VIN 1V/DIV Start-Up/Dropout Performance VIN 1V/DIV VIN VOUT TA = 25°C, unless otherwise noted. VIN VSW 5V/DIV VOUT IL 0.5A/DIV VOUT 1V/DIV VOUT 1V/DIV Burst Mode Switching Waveforms VOUT 10mV/DIV 2.5Ω LOAD 100ms/DIV (2A IN REGULATION) 1kΩ LOAD 100ms/DIV (5mA IN REGULATION) 3976 G33 Full Frequency Switching Waveforms VSW 2V/DIV IL 1A/DIV IL 1A/DIV VOUT 20mV/DIV VOUT 50mV/DIV 3976 G36 1µs/DIV VIN = 5V 5µs/DIV VOUT SET FOR 5V ILOAD = 0.5A COUT = 47µF Load Transient: 0.5A to 4.5A IL 2A/DIV VOUT 200mV/DIV VOUT 500mV/DIV 50µs/DIV 5µs/DIV 3976 G35 3976 G37 Load Transient: 10mA to 4A IL 2A/DIV 12VIN 3.3VOUT COUT = 2 × 47µF VIN = 12V VOUT = 3.3V ILOAD = 20mA COUT = 47µF Dropout Switching Waveforms VSW 5V/DIV VIN = 12V VOUT = 3.3V ILOAD = 1A COUT = 47µF 3976 G34 3976 G38 12VIN 3.3VOUT COUT = 2 × 47µF 50µs/DIV 3976 G39 3976f 8 For more information www.linear.com/3976 LT3976 Pin Functions (MSE/UDD) FB (Pin 1/Pins 23, 24): The LT3976 regulates the FB pin to 1.197V. Connect the feedback resistor divider tap to this pin. Also, connect a phase lead capacitor between FB and the output. Typically, this capacitor is 10pF. SS (Pin 2/Pin 1): A capacitor is tied between SS and ground to slowly ramp up the peak current limit of the LT3976 on start-up. There is an internal 1.8μA pull-up on this pin. The soft-start capacitor is actively discharged when the EN pin goes low, during undervoltage lockout or thermal shutdown. Float this pin to disable soft-start. OUT (Pin 3/Pin 2): This pin is an input to the dropout comparator which maintains a minimum dropout of 500mV between VIN and OUT. The OUT pin connects to the anode of the internal boost diode. This pin also supplies the current to the LT3976’s internal regulator when OUT is above 3.2V. Connect this pin to the output when the programmed output voltage is less than 16V. BOOST (Pin 4/Pin 4): This pin is used to provide a drive voltage, higher than the input voltage, to the internal bipolar NPN power switch. SW (Pins 5, 6, 7/Pins 6, 7, 8): The SW pin is the output of an internal power switch. Connect these pins to the inductor, catch diode, and boost capacitor. An R-C snubber to GND is needed to ensure robustness under all conditions. Typical values are 2Ω and 470pF. VIN (Pins 10, 11, 12/Pins 13, 14, 15): The VIN pin supplies current to the LT3976’s internal circuitry and to the internal power switch. These pins must be locally bypassed. EN (Pin 13/Pin 16): The part is in shutdown when this pin is low and active when this pin is high. The hysteretic threshold voltage is 1.08V going up and 1.02V going down. The EN threshold is only accurate when VIN is above 4.3V. If VIN is lower than 3.9V, internal UVLO will place the part in shutdown. Tie to VIN if shutdown feature is not used. RT (Pin 14/Pin 18): A resistor is tied between RT and ground to set the switching frequency. PG (Pin 15/Pin 19): The PG pin is the open-drain output of an internal comparator. PGOOD remains low until the FB pin is within 8.4% of the final regulation voltage. PGOOD is valid when VIN is above 2V. SYNC (Pin 16/Pin 20): This is the external clock synchronization input. Ground this pin for low ripple Burst Mode operation at low output loads. Tie to a clock source for synchronization, which will include pulse skipping at low output loads. When in pulse-skipping mode, quiescent current increases to 11µA in a typical application at no load. Do not float this pin. GND (Exposed Pad Pin 17/Pin 21, Exposed Pad Pin 25): Ground. The exposed pad must be soldered to the PCB. NC (Pins 8, 9/Pins 3, 5, 9-12, 17, 22): No Connects. These pins are not connected to internal circuitry. 3976f For more information www.linear.com/3976 9 LT3976 Block Diagram OUT VIN C1 INTERNAL 1.197V REF EN 1.02V + – + SHDN RT 0.5V – + SLOPE COMP OSCILLATOR 200kHz TO 2MHz RT SYNC + – + – VIN SWITCH LATCH BOOST R S C3 Q Burst Mode DETECT PG ERROR AMP + – + – 1.097V VC L1 SW R3 C6 VOUT D1 C2 VC CLAMP 1.8µA SS SHDN C4 OPT FB GND R2 R1 3976 BD C5 3976f 10 For more information www.linear.com/3976 LT3976 Operation The LT3976 is a constant frequency, current mode stepdown regulator. An oscillator, with frequency set by RT, sets an RS flip-flop, turning on the internal power switch. An amplifier and comparator monitor the current flowing between the VIN and SW pins, turning the switch off when this current reaches a level determined by the voltage at VC (see Block Diagram). An error amplifier measures the output voltage through an external resistor divider tied to the FB pin and servos the VC node. If the error amplifier’s output increases, more current is delivered to the output; if it decreases, less current is delivered. An active clamp on the VC pin provides current limit. The VC pin is also clamped by the voltage on the SS pin; soft-start is implemented by generating a voltage ramp at the SS pin using an external capacitor. An internal regulator provides power to the control circuitry. The bias regulator normally draws power from the VIN pin, but if the OUT pin is connected to an external voltage higher than 3.2V, bias power will be drawn from the external source (typically the regulated output voltage). This improves efficiency. If the EN pin is low, the LT3976 is shut down and draws 700nA from the input. When the EN pin falls below 1.02V, the switching regulator will shut down, and when the EN pin rises above 1.08V, the switching regulator will become active. This accurate threshold allows programmable undervoltage lockout. The switch driver operates from either VIN or from the BOOST pin. An external capacitor is used to generate a voltage at the BOOST pin that is higher than the input supply. This allows the driver to fully saturate the internal bipolar NPN power switch for efficient operation. To further optimize efficiency, the LT3976 automatically switches to Burst Mode operation in light load situations. Between bursts, all circuitry associated with controlling the output switch is shut down reducing the input supply current to 1.7μA. In a typical application, 3.3μA will be consumed from the supply when regulating with no load. The oscillator reduces the LT3976’s operating frequency when the voltage at the FB pin is low. This frequency foldback helps to control the output current during startup and overload. The LT3976 can provide up to 5A of output current. A current limit foldback feature throttles back the current limit during overload conditions to limit the power dissipation. When SS is below 2V, the LT3976 overrides the current limit foldback circuit to avoid interfering with start-up. Thermal shutdown further protects the part from excessive power dissipation, especially in elevated ambient temperature environments. If the input voltage decreases towards the programmed output voltage, the LT3976 will start to skip switch-off times and decrease the switching frequency to maintain output regulation. As the input voltage decreases below the programmed output voltage, the output voltage will be regulated 500mV below the input voltage. This enforced minimum dropout voltage limits the duty cycle and keeps the boost capacitor charged during dropout conditions. Since sufficient boost voltage is maintained, the internal switch can fully saturate yielding low dropout performance. The LT3976 contains a power good comparator which trips when the FB pin is at 91.6% of its regulated value. The PG output is an open-drain transistor that is off when the output is in regulation, allowing an external resistor to pull the PG pin high. Power good is valid when VIN is above 2V. When the LT3976 is shut down the PG pin is actively pulled low. 3976f For more information www.linear.com/3976 11 LT3976 Applications Information Achieving Ultralow Quiescent Current To enhance efficiency at light loads, the LT3976 operates in low ripple Burst Mode operation, which keeps the output capacitor charged to the desired output voltage while minimizing the input quiescent current. In Burst Mode operation the LT3976 delivers single pulses of current to the output capacitor followed by sleep periods where the output power is supplied by the output capacitor. When in sleep mode the LT3976 consumes 1.7μA, but when it turns on all the circuitry to deliver a current pulse, the LT3976 consumes several mA of input current in addition to the switch current. Therefore, the total quiescent current will be greater than 1.7μA when regulating. As the output load decreases, the frequency of single current pulses decreases (see Figure 1) and the percentage of time the LT3976 is in sleep mode increases, resulting in much higher light load efficiency. By maximizing the time between pulses, the converter quiescent current gets closer to the 1.7μA ideal. Therefore, to optimize the quiescent current performance at light loads, the current in the feedback resistor divider and the reverse current in the catch diode must be minimized, as these appear to the output as load currents. Use the largest possible feedback resistors and a low leakage Schottky catch diode in applications utilizing the ultralow quiescent current performance of the LT3976. The feedback resistors should preferably be on the order of MΩ and the Schottky catch 900 SWITCHING FREQUENCY (kHz) 800 VOUT = 5V fSW = 800kHz 700 600 VOUT = 3.3V fSW = 600kHz 300 200 100 0 0 20 It is important to note that another way to decrease the pulse frequency is to increase the magnitude of each single current pulse. However, this increases the output voltage ripple because each cycle delivers more power to the output capacitor. The magnitude of the current pulses was selected to ensure less than 15mV of output ripple in a typical application. See Figure 2. VSW 5V/DIV IL 0.5A/DIV VOUT 10mV/DIV VIN = 12V VOUT = 3.3V ILOAD = 20mA COUT = 47µF 5µs/DIV 3976 F02 Figure 2. Burst Mode Operation While in Burst Mode operation, the burst frequency and the charge delivered with each pulse will not change with output capacitance. Therefore, the output voltage ripple will be inversely proportional to the output capacitance. In a typical application with a 22µF output capacitor, the output ripple is about 10mV, and with a 47µF output capacitor the output ripple is about 5mV. The output voltage ripple can continue to be decreased by increasing the output capacitance, though care must be taken to minimize the effects of output capacitor ESR and ESL. At higher output loads (above 150mA for the front page application) the LT3976 will be running at the frequency programmed by the RT resistor, and will be operating in standard PWM mode. The transition between PWM and low ripple Burst Mode operation is seamless, and will not disturb the output voltage. 500 400 diode should have less than a few µA of typical reverse leakage at room temperature. These two considerations are reiterated in the FB Resistor Network and Catch Diode Selection sections. 40 60 80 100 120 140 160 LOAD CURRENT (mA) 3976 F01 Figure 1. Switching Frequency in Burst Mode Operation To ensure proper Burst Mode operation, the SYNC pin must be grounded. When synchronized with an external clock, the LT3976 will pulse skip at light loads. At very 3976f 12 For more information www.linear.com/3976 LT3976 Applications Information light loads, the part will go to sleep between groups of pulses, so the quiescent current of the part will still be low, but not as low as in Burst Mode operation. The quiescent current in a typical application when synchronized with an external clock is 11µA at no load. Holding the SYNC pin DC high yields no advantages in terms of output ripple or minimum load to full frequency, so is not recommended. Table 1. Switching Frequency vs RT Value FB Resistor Network The output voltage is programmed with a resistor divider between the output and the FB pin. Choose the resistor values according to: ⎛ V ⎞ R1= R2 ⎜ OUT – 1⎟ ⎝ 1.197V ⎠ Reference designators refer to the Block Diagram. 1% resistors are recommended to maintain output voltage accuracy. The total resistance of the FB resistor divider should be selected to be as large as possible to enhance low current performance. The resistor divider generates a small load on the output, which should be minimized to optimize the low supply current at light loads. When using large FB resistors, a 10pF phase lead capacitor should be connected from VOUT to FB. Setting the Switching Frequency The LT3976 uses a constant frequency PWM architecture that can be programmed to switch from 200kHz to 2MHz by using a resistor tied from the RT pin to ground. A table showing the necessary RT value for a desired switching frequency is in Table 1. To estimate the necessary RT value for a desired switching frequency, use the equation: RT = 51.1 1.09 ( fSW ) – 9.27 where RT is in kΩ and fSW is in MHz. SWITCHING FREQUENCY (MHz) RT VALUE (kΩ) 0.2 294 0.3 182 0.4 130 0.6 78.7 0.8 54.9 1.0 41.2 1.2 32.4 1.4 26.1 1.6 21.5 1.8 17.8 2.0 14.7 2.2 12.4 Operating Frequency Trade-Offs Selection of the operating frequency is a trade-off between efficiency, component size, minimum dropout voltage, and maximum input voltage. The advantage of high frequency operation is that smaller inductor and capacitor values may be used. The disadvantages are lower efficiency, and lower maximum input voltage. The highest acceptable switching frequency (fSW(MAX)) for a given application can be calculated as follows: fSW(MAX) = VOUT + VD tON(MIN) ( VIN – VSW + VD ) where VIN is the typical input voltage, VOUT is the output voltage, VD is the catch diode drop (~0.5V), and VSW is the internal switch drop (~0.3V at max load). This equation shows that slower switching frequency is necessary to safely accommodate high VIN/VOUT ratio. This is due to the limitation on the LT3976’s minimum on-time. The minimum on-time is a strong function of temperature. Use the typical minimum on-time curve to design for an application’s maximum temperature, while adding about 30% for part-to-part variation. The minimum duty cycle that can be achieved taking minimum on time into account is: DCMIN = fSW • tON(MIN) where fSW is the switching frequency, the tON(MIN) is the minimum switch on-time. 3976f For more information www.linear.com/3976 13 LT3976 Applications Information A good choice of switching frequency should allow adequate input voltage range (see next two sections) and keep the inductor and capacitor values small. Maximum Input Voltage Range The LT3976 can operate from input voltages of up to 40V. Often the highest allowed VIN during normal operation (VIN(OP-MAX)) is limited by the minimum duty cycle rather than the absolute maximum ratings of the VIN pin. It can be calculated using the following equation: VIN(OP-MAX) = VOUT + VD – VD + VSW fSW • tON(MIN) where tON(MIN) is the minimum switch on-time. A lower switching frequency can be used to extend normal operation to higher input voltages. The circuit will tolerate inputs above the maximum operating input voltage and up to the absolute maximum ratings of the VIN and BOOST pins, regardless of chosen switching frequency. However, during such transients where VIN is higher than VIN(OP-MAX), the LT3976 will enter pulse-skipping operation where some switching pulses are skipped to maintain output regulation. The output voltage ripple and inductor current ripple will be higher than in typical operation. Do not overload when VIN is greater than VIN(OP-MAX). During start-up or overload, the switch node slews very fast due to the 10A peak current limit. At high voltages during these conditions, an R-C snubber on the switch node is required to ensure robustness of the LT3976. Typical values for the snubber are 2Ω and 470pF. See the Typical Applications section to see how the snubber is connected. Minimum Input Voltage Range The minimum input voltage is determined by either the LT3976’s minimum operating voltage of 4.3V, its maximum duty cycle, or the enforced minimum dropout voltage. See the Typical Performance Characteristics section for the minimum input voltage across load for outputs of 3.3V and 5V. The duty cycle is the fraction of time that the internal switch is on during a clock cycle. Unlike many fixed frequency regulators, the LT3976 can extend its duty cycle by remaining on for multiple clock cycles. The LT3976 will not switch off at the end of each clock cycle if there is sufficient voltage across the boost capacitor (C3 in the Block Diagram). Eventually, the voltage on the boost capacitor falls and requires refreshing. When this occurs, the switch will turn off, allowing the inductor current to recharge the boost capacitor. This places a limitation on the maximum duty cycle as follows: DCMAX = βSW βSW + 1 where βSW is equal to the beta of the internal power switch. The beta of the power switch is typically about 50, which leads to a DCMAX of about 98%. This leads to a minimum input voltage of approximately: VIN(MIN1) = VOUT + VD – VD + VSW DCMAX where VOUT is the output voltage, VD is the catch diode drop, VSW is the internal switch drop and DCMAX is the maximum duty cycle. The final factor affecting the minimum input voltage is the minimum dropout voltage. When the OUT pin is tied to the output, the LT3976 regulates the output such that it stays 500mV below VIN. This enforced minimum dropout voltage is due to reasons that are covered in the next section. This places a limitation on the minimum input voltage as follows: VIN(MIN2) = VOUT + VDROPOUT(MIN) where VOUT is the programmed output voltage and VDROPOUT(MIN) is the minimum dropout voltage of 500mV. Combining these factors leads to the overall minimum input voltage: VIN(MIN) = Max (VIN(MIN1), VIN(MIN2), 4.3V) 3976f 14 For more information www.linear.com/3976 LT3976 Applications Information Minimum Dropout Voltage To achieve a low dropout voltage, the internal power switch must always be able to fully saturate. This means that the boost capacitor, which provides a base drive higher than VIN, must always be able to charge up when the part starts up and then must also stay charged during all operating conditions. During start-up if there is insufficient inductor current, such as during light load situations, the boost capacitor will be unable to charge. When the LT3976 detects that the boost capacitor is not charged, it activates a 100mA (typical) pull-down on the OUT pin. If the OUT pin is connected to the output, the extra load will increase the inductor current enough to sufficiently charge the boost capacitor. When the boost capacitor is charged, the current source turns off, and the part may re-enter Burst Mode operation. To keep the boost capacitor charged regardless of load during dropout conditions, a minimum dropout voltage is enforced. When the OUT pin is tied to the output, the LT3976 regulates the output such that: VIN – VOUT > VDROPOUT(MIN) where VDROPOUT(MIN) is 500mV. The 500mV dropout voltage limits the duty cycle and forces the switch to turn off regularly to charge the boost capacitor. Since sufficient voltage across the boost capacitor is maintained, the switch is allowed to fully saturate and the internal switch drop stays low for good dropout performance. Figure 3 shows the overall VIN to VOUT performances during start-up and dropout conditions. VIN 1V/DIV VIN VOUT VOUT 1V/DIV 1kΩ LOAD 100ms/DIV (5mA IN REGULATION) 3976 F03 It is important to note that the 500mV dropout voltage specified is the minimum difference between VIN and VOUT. When measuring VIN to VOUT with a multimeter, the measured value will be higher than 500mV because you have to add half the ripple voltage on the input and half the ripple voltage on the output. With the normal ceramic capacitors specified in the data sheet, this measured dropout voltage can be as high as 650mV at high load. If some bulk electrolytic capacitance is added to the input and output the voltage ripple, and subsequently the measured dropout voltage, can be significantly reduced. Additionally, when operating in dropout at high currents, high ripple voltage on the input and output can generate audible noise. This noise can also be significantly reduced by adding bulk capacitance to the input and output to reduce the voltage ripple. Inductor Selection and Maximum Output Current For a given input and output voltage, the inductor value and switching frequency will determine the ripple current. The ripple current increases with higher VIN or VOUT and decreases with higher inductance and faster switching frequency. A good first choice for the inductor value is: L= VOUT + VD 2fSW where fSW is the switching frequency in MHz, VOUT is the output voltage, VD is the catch diode drop (~0.5V) and L is the inductor value is μH. The inductor’s RMS current rating must be greater than the maximum load current and its saturation current should be about 30% higher. For robust operation in fault conditions (start-up or overload) and high input voltage (>30V), the saturation current should be above 13A. To keep the efficiency high, the series resistance (DCR) should be less than 0.1Ω, and the core material should be intended for high frequency applications. Table 2 lists several inductor vendors. Figure 3. VIN to VOUT Performance 3976f For more information www.linear.com/3976 15 LT3976 Applications Information Table 2. Inductor Vendors VENDOR URL Coilcraft www.coilcraft.com Sumida www.sumida.com Toko www.tokoam.com Würth Elektronik www.we-online.com Coiltronics www.cooperet.com Murata www.murata.com The inductor value must be sufficient to supply the desired maximum output current (IOUT(MAX)), which is a function of the switch current limit (ILIM) and the ripple current. IOUT(MAX) = ILIM – ΔIL 2 The LT3976 limits its peak switch current in order to protect itself and the system from overload and short-circuit faults. The LT3976’s switch current limit (ILIM) is typically 10A at low duty cycles and decreases linearly to 8A at DC = 0.8. When the switch is off, the potential across the inductor is the output voltage plus the catch diode drop. This gives the peak-to-peak ripple current in the inductor: ΔIL = (1– DC) • ( VOUT + VD ) L • fSW where fSW is the switching frequency of the LT3976, DC is the duty cycle and L is the value of the inductor. Therefore, the maximum output current that the LT3976 will deliver depends on the switch current limit, the inductor value, and the input and output voltages. The inductor value may have to be increased if the inductor ripple current does not allow sufficient maximum output current (IOUT(MAX)) given the switching frequency, and maximum input voltage used in the desired application. The optimum inductor for a given application may differ from the one indicated by this simple design guide. A larger value inductor provides a higher maximum load current and reduces the output voltage ripple. If your load is lower than the maximum load current, than you can relax the value of the inductor and operate with higher ripple current. This allows you to use a physically smaller inductor, or one with a lower DCR resulting in higher efficiency. Be aware that if the inductance differs from the simple rule above, then the 16 maximum load current will depend on the input voltage. In addition, low inductance may result in discontinuous mode operation, which further reduces maximum load current. For details of maximum output current and discontinuous operation, see Linear Technology’s Application Note 44. Finally, for duty cycles greater than 50% (VOUT/VIN > 0.5), a minimum inductance is required to avoid sub-harmonic oscillations, see Application Note 19. One approach to choosing the inductor is to start with the simple rule given above, look at the available inductors, and choose one to meet cost or space goals. Then use the equations above to check that the LT3976 will be able to deliver the required output current. Note again that these equations assume that the inductor current is continuous. Discontinuous operation occurs when IOUT is less than ΔIL/2. Current Limit Foldback and Thermal Protection The LT3976 has a large peak current limit to ensure a 5A max output current across duty cycle and current limit distribution, as well as allowing a reasonable inductor ripple current. During a short-circuit fault, having a large current limit can lead to excessive power dissipation and temperature rise in the LT3976, as well as the inductor and catch diode. To limit this power dissipation, the LT3976 starts to fold back the current limit when the FB pin falls below 0.8V. The LT3976 typically lowers the peak current limit about 50% from 10A to 5A. During start-up, when the output voltage and FB pin are low, current limit foldback could hinder the LT3976’s ability to start up into a large load. To avoid this potential problem, the LT3976’s current limit foldback will be disabled until the SS pin has charged above 2V. Therefore, the use of a soft-start capacitor will keep the current limit foldback feature out of the way while the LT3976 is starting up. The LT3976 has thermal shutdown to further protect the part during periods of high power dissipation, particularly in high ambient temperature environments. The thermal shutdown feature detects when the LT3976 is too hot and shuts the part down, preventing switching. When the thermal event passes and the LT3976 cools, the part will restart and resume switching. A thermal shutdown event actively discharges the soft-start capacitor. For more information www.linear.com/3976 3976f LT3976 Applications Information Input Capacitor Bypass the input of the LT3976 circuit with a ceramic capacitor of X7R or X5R type. Y5V types have poor performance over temperature and applied voltage, and should not be used. A 4.7μF to 10μF ceramic capacitor is adequate to bypass the LT3976 and will easily handle the ripple current. Note that larger input capacitance is required when a lower switching frequency is used (due to longer on times). If the input power source has high impedance, or there is significant inductance due to long wires or cables, additional bulk capacitance may be necessary. This can be provided with a low performance electrolytic capacitor. Step-down regulators draw current from the input supply in pulses with very fast rise and fall times. The input capacitor is required to reduce the resulting voltage ripple at the LT3976 and to force this very high frequency switching current into a tight local loop, minimizing EMI. A 10μF capacitor is capable of this task, but only if it is placed close to the LT3976 (see the PCB Layout section). A second precaution regarding the ceramic input capacitor concerns the maximum input voltage rating of the LT3976. A ceramic input capacitor combined with trace or cable inductance forms a high quality (under damped) tank circuit. If the LT3976 circuit is plugged into a live supply, the input voltage can ring to twice its nominal value, possibly exceeding the LT3976’s voltage rating. If the input supply is poorly controlled or the user will be plugging the LT3976 into an energized supply, the input network should be designed to prevent this overshoot. See Linear Technology Application Note 88 for a complete discussion. Output Capacitor and Output Ripple The output capacitor has two essential functions. Along with the inductor, it filters the square wave generated by the LT3976 to produce the DC output. In this role it determines the output ripple, so low impedance (at the switching frequency) is important. The second function is to store energy in order to satisfy transient loads and stabilize the LT3976’s control loop. Ceramic capacitors have very low equivalent series resistance (ESR) and provide the best ripple performance. A good starting value is: COUT = where fSW is in MHz, and COUT is the recommended output capacitance in μF. Use X5R or X7R types. This choice will provide low output ripple and good transient response. Transient performance can be improved with a higher value capacitor if combined with a phase lead capacitor (typically 10pF) between the output and the feedback pin. A lower value of output capacitor can be used to save space and cost but transient performance will suffer. When choosing a capacitor, look carefully through the data sheet to find out what the actual capacitance is under operating conditions (applied voltage and temperature). A physically larger capacitor or one with a higher voltage rating may be required. Table 3 lists several capacitor vendors. Table 3. Recommended Ceramic Capacitor Vendors MANUFACTURER URL AVX www.avxcorp.com Murata www.murata.com Taiyo Yuden www.t-yuden.com Vishay Siliconix www.vishay.com TDK www.tdk.com Ceramic Capacitors When in dropout, the LT3976 can excite ceramic capacitors at audio frequencies. At high load, this could be unacceptable. Simply adding bulk input capacitance to the input and output will significantly reduce the voltage ripple and the audible noise generated at these nodes to acceptable levels. A final precaution regarding ceramic capacitors concerns the maximum input voltage rating of the LT3976. As previously mentioned, a ceramic input capacitor combined with trace or cable inductance forms a high quality (under damped) tank circuit. If the LT3976 circuit is plugged into a live supply, the input voltage can ring to twice its nominal value, possibly exceeding the LT3976’s rating. If the input supply is poorly controlled or the user will be plugging the LT3976 into an energized supply, the input network should be designed to prevent this overshoot. See Linear Technology Application Note 88 for a complete discussion. 300 VOUT • fSW 3976f For more information www.linear.com/3976 17 LT3976 Applications Information Catch Diode Selection The catch diode (D1 from the Block Diagram) conducts current only during the switch off time. Average forward current in normal operation can be calculated from: Table 4. Schottky Diodes. The Reverse Current Values Listed Are Estimates Based Off of Typical Curves for Reverse Current vs Reverse Voltage at 25°C IR at VR = 20V 25°C (µA) VR (V) IAVE (A) 40 5 450 500 120 B540C 40 5 510 550 2 PDS540 40 5 480 520 4 PDS560 60 5 610 670 0.9 SBR8A45SP5 45 8 450 — 18 SBR8AU60P5 60 8 400 — 60 PART NUMBER ⎛V – V ⎞ ID(AVG) = IOUT ⎜ IN OUT ⎟ VIN ⎝ ⎠ VF at 5A MAX 25°C (mV) VF at 5A TYP 25°C (mV) On Semiconductor MBRS540T3 where IOUT is the output load current. The current rating of the diode should be selected to be greater than or equal to the application’s output load current, so that the diode is robust for a wide input voltage range. A diode with even higher current rating can be selected for the worst-case scenario of overload, where the max diode current can then increase to the typical peak switch current. Short circuit is not the worst-case condition due to current limit foldback. Peak reverse voltage is equal to the regulator input voltage. For inputs up to 40V, a 40V diode is adequate. An additional consideration is reverse leakage current. When the catch diode is reversed biased, any leakage current will appear as load current. When operating under light load conditions, the low supply current consumed by the LT3976 will be optimized by using a catch diode with minimum reverse leakage current. Low leakage Schottky diodes often have larger forward voltage drops at a given current, so a trade-off can exist between low load and high load efficiency. Often Schottky diodes with larger reverse bias ratings will have less leakage at a given output voltage than a diode with a smaller reverse bias rating. Therefore, superior leakage performance can be achieved at the expense of diode size. Table 4 lists several Schottky diodes and their manufacturers. Diodes Inc. charge the boost capacitor. Above 16V, the OUT pin abs max is violated. For outputs between 2.5V and 3.2V, an external Schottky diode to the output is sufficient because an external Schottky will have much lower forward voltage drop than the internal boost diode. BOOST and OUT Pin Considerations For output voltages less than 2.5V, there are two options. An external Schottky diode can charge the boost capacitor from the input (Figure 4c) or from an external voltage source (Figure 4d). Using an external voltage source is the better option because it is more efficient than charging the boost capacitor from the input. However, such a voltage rail is not always available in all systems. For output voltages greater than 16V, an external Schottky diode from an external voltage source should be used to charge the boost capacitor (Figure 4e). In applications using an external voltage source, the supply should be between 3.1V and 16V. When using the input, the input voltage may not exceed 27V. In all cases, the maximum voltage rating of the BOOST pin must not be exceeded. Capacitor C3 and the internal boost Schottky diode (see the Block Diagram) are used to generate a boost voltage that is higher than the input voltage. In most cases a 0.47μF capacitor will work well. The BOOST pin must be more than 1.8V above the SW pin for best efficiency and more than 2.6V above the SW pin to allow the LT3976 to skip off times to achieve very high duty cycles. For outputs between 3.2V and 16V, the standard circuit with the OUT pin connected to the output (Figure 4a) is best. Below 3.2V the internal Schottky diode may not be able to sufficiently When the output is above 16V, the OUT pin can not be tied to the output or the OUT pin abs max will be violated. It should instead be tied to GND (Figure 4e). This is to prevent the dropout circuitry from interfering with switching behavior and to prevent the 100mA active pull-down from drawing power. It is important to note that when the output is above 16V and the OUT pin is grounded, the dropout circuitry is not connected, so the minimum dropout will be about 1.5V, rather than 500mV. If the output is less than 3.2V and an external Schottky is used 18 For more information www.linear.com/3976 3976f LT3976 Applications Information to charge the boost capacitor, the OUT pin should still be tied to the output even though the minimum input voltage of the LT3976 will be limited by the 4.3V minimum rather than the minimum dropout voltage. Enable and Undervoltage Lockout The LT3976 is in shutdown when the EN pin is low and active when the pin is high. The falling threshold of the EN comparator is 1.02V, with 60mV of hysteresis. The EN pin can be tied to VIN if the shutdown feature is not used. With the OUT pin connected to the output, a 100mA active load will charge the boost capacitor during light load start-up and an enforced 500mV minimum dropout voltage will keep the boost capacitor charged across operating conditions (see Minimum Dropout Voltage section). This yields excellent start-up and dropout performance. Figure 5 shows the minimum input voltage for 3.3V and 5V outputs. VIN BOOST SW VIN VIN LT3976 GND BOOST SW VIN VIN LT3976 OUT VOUT GND (4a) For 3.2V ≤ VOUT ≤ 16V BOOST VIN OUT VOUT GND (4b) For 2.5V ≤ VOUT ≤ 3.2V BOOST VIN OUT VOUT (4c) For VOUT < 2.5V, VIN < 27V VS SW VIN VIN LT3976 GND SW LT3976 VS BOOST SW LT3976 OUT VOUT GND OUT VOUT 3976 F04 (4d) For VOUT < 2.5V, 3.1V ≤ VS ≤ 16V (4e) For VOUT > 16V, 3.1V ≤ VS ≤ 16V Figure 4. Five Circuits for Generating the Boost Voltage 6.5 5.0 VOUT = 5V fSW = 800kHz 6.0 5.5 5.0 4.5 4.0 VOUT = 3.3V FRONT PAGE APPLICATION 4.5 TO RUN/TO START INPUT VOLTAGE (V) INPUT VOLTAGE (V) VIN Undervoltage lockout (UVLO) can be added to the LT3976 as shown in Figure 6. Typically, UVLO is used in situations where the input supply is current limited, or has a relatively high source resistance. A switching regulator draws constant power from the source, so source current increases as source voltage drops. This looks like a TO RUN/TO START 4.0 3.5 3.0 0 1 3 2 LOAD CURRENT (A) 4 5 2.5 0 1 3 2 LOAD CURRENT (A) 4 3976 F05a 5 3976 F05b Figure 5. The Minimum Input Voltage Depends on Output Voltage and Load Current 3976f For more information www.linear.com/3976 19 LT3976 Applications Information VIN R3 LT3976 1.02V EN + – IL 1A/DIV SHDN VOUT 1V/DIV R4 LT3976 F06 VSS 0.5V/DIV Figure 6. Undervoltage Lockout negative resistance load to the source and can cause the source to current limit or latch low under low source voltage conditions. UVLO prevents the regulator from operating at source voltages where the problems might occur. The UVLO threshold can be adjusted by setting the values R3 and R4 such that they satisfy the following equation: ⎛ R3+R4 ⎞ VUVLO = VEN(THRESH) ⎜ ⎟ ⎝ ⎠ R4 where VEN(THRESH) is the falling threshold of the EN pin, which is approximately 1.02V, and where switching should stop when VIN falls below VUVLO. Note that due to the comparator’s hysteresis, switching will not start until the input is about 6% above VUVLO. When operating in Burst Mode operation for light load currents, the current through the UVLO resistor network can easily be greater than the supply current consumed by the LT3976. Therefore, the UVLO resistors should be large to minimize their effect on efficiency at low loads. Soft-Start The SS pin can be used to soft start the LT3976 by throttling the maximum input current during start-up and reset. An internal 1.8μA current source charges an external capacitor generating a voltage ramp on the SS pin. The SS pin clamps the internal VC node, which slowly ramps up the current limit. Maximum current limit is reached when the SS pin is about 1.5V or higher. By selecting a large enough capacitor, the output can reach regulation without overshoot. Figure 7 shows start-up waveforms for a typical application with a 10nF capacitor on SS for a 1.65Ω load when the EN pin is pulsed high for 7ms. The external SS capacitor is actively discharged when the EN pin is low, or during thermal shutdown. The active pull-down on the SS pin has a resistance of about 150Ω. 1ms/DIV 3976 F07 Figure 7. Soft-Start Waveforms for the Front-Page Application with a 10nF Capacitor on SS. EN Is Pulsed High for About 7ms with a 1.65Ω Load Resistor Synchronization To select low ripple Burst Mode operation, tie the SYNC pin below 0.5V (this can be ground or a logic output). Synchronizing the LT3976 oscillator to an external frequency can be done by connecting a square wave (with 20% to 80% duty cycle) to the SYNC pin. The square wave amplitude should have valleys that are below 0.5V and peaks above 1.5V (up to 6V). The LT3976 will pulse skip at low output loads while synchronized to an external clock to maintain regulation. At very light loads, the part will go to sleep between groups of pulses, so the quiescent current of the part will still be low, but not as low as in Burst Mode operation. The quiescent current in a typical application when synchronized with an external clock is 11µA at no load. Holding the SYNC pin DC high yields no advantages in terms of output ripple or minimum load to full frequency, so is not recommended. Never float the SYNC pin. The LT3976 may be synchronized over a 250kHz to 2MHz range. The RT resistor should be chosen to set the LT3976 switching frequency 20% below the lowest synchronization input. For example, if the synchronization signal will be 250kHz and higher, the RT should be selected for 200kHz. To assure reliable and safe operation the LT3976 will only synchronize when the output voltage is near regulation as indicated by the PG flag. It is therefore necessary to choose a large enough inductor value to supply the required output current at the frequency set by the RT resistor (see Inductor Selection section). The slope compensation is set by the RT value, while the minimum slope compensation required to avoid subharmonic oscillations is established 3976f 20 For more information www.linear.com/3976 LT3976 Applications Information by the inductor size, input voltage and output voltage. Since the synchronization frequency will not change the slopes of the inductor current waveform, if the inductor is large enough to avoid subharmonic oscillations at the frequency set by RT, than the slope compensation will be sufficient for all synchronization frequencies. Power Good Flag The PG pin is an open-drain output which is used to indicate to the user when the output voltage is within regulation. When the output is lower than the regulation voltage by more than 8.4%, as determined from the FB pin voltage, the PG pin will pull low to indicate the power is not good. Otherwise, the PG pin will go high impedance and can be pulled logic high with a resistor pull-up. The PG pin is only comparing the output voltage to an accurate reference when the LT3976 is enabled and VIN is above 4.3V. When the part is shutdown, the PG is actively pulled low to indicate that the LT3976 is not regulating the output. The input voltage must be greater than 1.4V to fully turn-on the active pull-down device. Figure 8 shows the status of the PG pin as the input voltage is increased. Protection section). There is another situation to consider in systems where the output will be held high when the input to the LT3976 is absent. This may occur in battery charging applications or in battery backup systems where a battery or some other supply is diode ORed with the LT3976’s output. If the VIN pin is allowed to float and the EN/UVLO pin is held high (either by a logic signal or because it is tied to VIN), then the LT3976’s internal circuitry will pull its quiescent current through its SW pin. This is fine if your system can tolerate a few μA in this state. If you ground the EN pin, the SW pin current will drop to essentially zero. However, if the VIN pin is grounded while the output is held high, regardless of EN, parasitic diodes inside the LT3976 can pull current from the output through the SW pin and the VIN pin. Figure 9 shows a circuit that will run only when the input voltage is present and that protects against a shorted or reversed input. D4 PDS540 VIN EN PG PIN VOLTAGE (V) 4 BOOST VIN LT3976 GND VOUT SW OUT FB + BACKUP 3 3976 F09 2 Figure 9. Diode D4 Prevents a Shorted Input from Discharging a Backup Battery Tied to the Output. It Also Protects the Circuit from a Reversed Input. The LT3976 Runs Only When the Input Is Present 1 0 PCB Layout 0 0.5 1 1.5 2 2.5 3 3.5 INPUT VOLTAGE (V) 4 4.5 5 3976 F08 Figure 8. PG Pin Voltage Versus Input Voltage when PG Is Connected to 3V Through a 150k Resistor. The FB Pin Voltage Is 1.15V Shorted and Reversed Input Protection If the inductor is chosen so that it won’t saturate excessively, a LT3976 buck regulator will tolerate a shorted output and the power dissipation will be limited by current limit foldback (see Current Limit Foldback and Thermal For proper operation and minimum EMI, care must be taken during printed circuit board layout. Figure 10 shows a sample component placement with trace, ground plane and via locations, which serves as a good PCB layout example. Note that large, switched currents flow in the LT3976’s VIN and SW pins, the catch diode (D1), and the input capacitor (C1). The loop formed by these components should be as small as possible. These components, along with the inductor and output capacitor, should be placed on the same side of the circuit board, and their connections should be made on that layer. Place a local, 3976f For more information www.linear.com/3976 21 LT3976 Applications Information VOUT FB OUT BST 17 ••• ••• •• •• •• •• •• •• •• •• •• ••• ••• ••• SW VOUT PG RT VIN EN 3976 F10 Figure 10. Layout Showing a Good PCB Design unbroken ground plane below these components. The SW and BOOST nodes should be as small as possible. Finally, keep the FB and RT nodes small so that the ground traces will shield it from the SW and BOOST nodes. The exposed pad on the bottom of the package must be soldered to ground so that the pad acts as a heat sink. To keep thermal resistance low, extend the ground plane as much as possible, and add thermal vias under and near the LT3976 to additional ground planes within the circuit board and on the bottom side. High Temperature Considerations Also keep in mind that the leakage current of the power Schottky diode goes up exponentially with junction temperature. When the power switch is off, the power Schottky diode is in parallel with the power converter’s output filter stage. As a result, an increase in a diode’s leakage current results in an effective increase in the load, and a corresponding increase in the input quiescent current. Therefore, the catch Schottky diode must be selected with care to avoid excessive increase in light load supply current at high temperatures. CHIP TEMPERATURE RISE (°C) SYNC 70 65 60 55 50 45 40 35 30 25 20 15 10 5 0 VOUT = 3.3V fSW = 400kHz 2.5in × 2.5in 4-LAYER BOARD 12V 24V 36V 1 3 4 2 OUTPUT CURRENT (A) 5 3976 F11a For higher ambient temperatures, care should be taken in the layout of the PCB to ensure good heat sinking of the LT3976. The exposed pad on the bottom of the package must be soldered to a ground plane. This ground should be tied to large copper layers below with thermal vias; these layers will spread the heat dissipated by the LT3976. Placing additional vias can reduce the thermal resistance further. When operating at high ambient temperatures, the maximum load current should be derated as the ambient temperature approaches the maximum junction rating. (See Thermal Derating curve in the Typical Performance Characteristics section.) Power dissipation within the LT3976 can be estimated by calculating the total power loss from an efficiency measurement and subtracting the catch diode loss and inductor loss. The die temperature is calculated by multiplying the Figure 11a. Temperature Rise of the LT3976 in the Front Page Application 90 VOUT = 5V fSW = 800kHz 2.5in × 2.5in 4-LAYER BOARD 80 CHIP TEMPERATURE RISE (°C) SS LT3976 power dissipation by the thermal resistance from junction to ambient. The temperature rise of the LT3976 for a 3.3V and 5V application was measured using a thermal camera and is shown in Figure 11. 70 60 50 40 30 20 12V 24V 36V 10 0 1 3 4 2 OUTPUT CURRENT (A) 5 3976 F11b Figure 11b. Temperature Rise of the LT3976 in a 5VOUT Application 3976f 22 For more information www.linear.com/3976 LT3976 Applications Information Fault Tolerance of QFN Package The QFN package is designed to tolerate single fault conditions. Shorting two adjacent pins together or leaving one single pin floating does not raise the output voltage or cause damage to the LT3976 regulator. However, the application circuit must meet a few requirements discussed in this section in order to achieve this fault tolerance. Tables 5 and 6 show the effects that result from shorting adjacent pins or from a floating pin, respectively. There are three items which require consideration in terms of the application circuit to achieve fault tolerance: SSOUT pin short, RT-PG pin short, and PG-SYNC pin short. If the output voltage is less than 6V, then the application circuit can be setup normally (see Figure 12a) because a SS to OUT short will not violate the SS pin 6V absolute maximum and a PG short to either RT or SYNC will not violate the 6V absolute maximum on each of those pins. If the output voltage is greater than 6V, the best way to solve the problem of violating the SS absolute maximum when shorted to OUT is to tie the OUT pin to GND. Note that grounding the OUT pin will compromise the dropout performance of the LT3976. When OUT is grounded, an external Schottky diode to either the output, VIN, or another voltage source must be used to charge the boost capacitor. The PG pull-up resistor must be increased Table 5. Effects of Pin Shorts PINS EFFECT SS-OUT VOUT may fall below regulation voltage for VOUT less than or equal to 6V. For outputs above 6V, the absolute maximum of the SS pin would be violated, so the OUT pin must be tied to GND (see discussion in the Fault Tolerance section) VIN-EN No effect. In most applications, EN is tied to VIN. If EN is driven with a logic signal, the customer must ensure that the circuit generating that signal can withstand the maximum VIN RT-PG No effect if PG is floated. VOUT will fall below regulation if PG is connected to the output with a resistor pull-up as long as the resister divider formed by the PG pin pull-up and the RT resistor prevents the RT pin absolute maximum from being violated (see discussion in the Fault Tolerance section). In both cases, the switching frequency will be significantly increased if the output goes below regulation, which may cause the LT3976 to go into pulse-skipping mode if the minimum on-time is violated. PG-SYNC No effect if PG is floated. No effect if PG is connected to the output with a resistor pull-up as long as there is a resistor to GND on the SYNC pin or the SYNC pin is tied to GND. This is to ensure that the resistor divider formed by the PG pin pull-up and the SYNC pin resistor to GND prevents the SYNC pin Absolute Maximum from being violated (see discussion in the Fault Tolerance section). Table 6. Effects of Floating Pins EFFECT SS No effect; soft-start feature will not function. OUT VOUT may fall below regulation voltage. With the OUT pin disconnected, the boost capacitor cannot be charged and thus the power switch cannot fully saturate, which increases power dissipation. BOOST SW 700 SWITCHING FREQUENCY (kHz) PIN VOUT may fall below regulation voltage. With the BOOST pin disconnected, the boost capacitor cannot be charged and thus the power switch cannot fully saturate, which increases power dissipation. No effect; there are several SW pins. No effect; there are several VIN pins. VOUT may fall below regulation voltage. Part may work normally or be shutdown depending on how the application circuit couples to the floating EN pin. RT VOUT may fall below regulation voltage. PG No effect. FB No effect. The LT3976 may be in Burst Mode operation or pulse-skipping mode depending on how the application circuit couples to the floating SYNC pin. No effect; there are two FB pins. No effect; there are several GND connections. If Exposed Pad is floated, thermal performance will be degraded. 3976f For more information www.linear.com/3976 400 300 200 100 0 0.2 0.8 0.6 0.4 FB PIN VOLTAGE (V) 1 1.2 3976 G22 EN GND 500 0 VIN SYNC 600 23 LT3976 Applications Information and a SYNC pin resistor to GND added, so that a PG pin short to either SYNC or RT will form resistor dividers to keep the voltage on the SYNC and RT pins below their rated absolute maximum. This application is shown in Figure 12b. The external Schottky must be connected such that the absolute maximum of the BOOST pin is not violated. The SYNC pin resistor can be removed if the SYNC pin is grounded or PG is left floating both of which also result in fault tolerant circuits. Other Linear Technology Publications Application Notes 19, 35 and 44 contain more detailed descriptions and design information for buck regulators and other switching regulators. The LT1376 data sheet has a more extensive discussion of output ripple, loop compensation and stability testing. Design Note 318 shows how to generate a bipolar output supply using a buck regulator. VIN BOOST VIN EN EXTERNAL INPUT 0.47µF 3.3µH SW 2Ω SYNC 470pF LT3976 10µF 10nF SS PG OUT RT FB 150k PGOOD 1M VOUT GND 34.9k 316k 47µF 1210 ×2 10pF 3976 F12a f = 800kHz Figure 12a. Fault Tolerant for VOUT < 6V (Note: For VOUT < 3.3V External Boost Schottky Diode Is Needed) VIN BOOST VIN EN EXTERNAL INPUT 0.47µF 3.3µH SW 2Ω SYNC 470pF LT3976 10µF 40.2k 10nF SS PG OUT RT FB 249k PGOOD 1M VOUT GND 54.9k 316k 47µF 1210 ×2 10pF 3976 F12b f = 800kHz Figure 12b. Fault Tolerant for VOUT < 27V (Note: For VOUT < 3V External Boost Schottky Diode Should Be Connected to the Input) Figure 12. Two Example Circuits to Achieve Fault Tolerance (FMEA) with the LT3976 QFN Package 3976f 24 For more information www.linear.com/3976 LT3976 Typical Applications 5V Step-Down Converter 12V Step-Down Converter VIN 13.2V* TO 40V VIN 6V* TO 40V VIN OFF ON VIN EN BOOST PG SW 10µF 10nF 0.47µF 3.3µH 10pF 3976 TA02 f = 800kHz D = PDS540 L = IHLP-2525CZ-01 * MINIMUM VIN CAN BE LOWERED WITH ADDITIONAL INPUT AND OUTPUT CAPACITANCE. 10nF OFF ON EN 10nF RT SYNC – 24V VOUT 5V 5A 1M 10pF CBULK 100µF BOOST 10µF ×2 10nF RT SYNC 130k f = 400kHz D = PDS540 L = IHLP-2525CZ-01 VOUT 4V 5A 1M FB GND 10pF 432k 3976 TA05 47µF 1210 ×2 VIN EN BOOST PG SW 10µF VOUT 2.5V 5A 1M 4.7pF 909k 3976 TA06 47µF 1210 ×4 SS 10nF 0.47µF 2.2µH 2Ω LT3976 470pF FB GND 470pF DFLS160 OFF ON 2Ω OUT 2Ω OUT RT SYNC VIN 4.3V TO 27V SW SS 0.47µF 3.3µH 54.9k 0.47µF LT3976 SW LT3976 47nF 10µF 3.3µH PG EN 1.8V Step-Down Converter DFLS160 VIN 3976 TA03 f = 800kHz D = PDS540 L = IHLP-2525CZ-01 3976 TA04 EN BOOST SS 2.5V Step-Down Converter OFF ON PG 499k 47µF 1210 f = 2MHz D = PDS540 L = IHLP-2525CZ-01 VIN 4.3V TO 40V 47µF 1210 VIN 5.49M + 150k 316k 14.7k 10pF 110k PGOOD FB GND VOUT 12V 5A 1M FB GND + V 470pF PG OUT SS RT SYNC 4V Step-Down Converter with a High Impedance Input Source SW LT3976 470pF OUT f = 800kHz D = PDS540 L = IHLP-4040DZ-01 * MINIMUM VIN CAN BE LOWERED WITH ADDITIONAL INPUT AND OUTPUT CAPACITANCE. 0.47µF 1.5µH 2Ω 4.7µF 2Ω 54.9k 5V, 2MHz Step-Down Converter with Power Good BOOST 0.47µF 6.8µH LT3976 47µF 1210 ×2 316k VIN SW SS VOUT 5V 5A 1M FB GND 54.9k VIN 5.9V TO 18V (40V TRANSIENTS) BOOST PG 470pF OUT RT SYNC EN 10µF 2Ω LT3976 SS OFF ON RT SYNC 97.6k f = 500kHz D = PDS540 L = IHLP-2525CZ-01 470pF OUT VOUT 1.8V 5A 499k FB GND 10pF 1M 3976 TA07 47µF 1210 ×4 3976f For more information www.linear.com/3976 25 LT3976 Package Description Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. MSE Package 16-Lead Plastic MSOP, Exposed Die Pad (Reference LTC DWG # 05-08-1667 Rev E) BOTTOM VIEW OF EXPOSED PAD OPTION 2.845 ±0.102 (.112 ±.004) 5.23 (.206) MIN 2.845 ±0.102 (.112 ±.004) 0.889 ±0.127 (.035 ±.005) 8 1 1.651 ±0.102 (.065 ±.004) 1.651 ±0.102 3.20 – 3.45 (.065 ±.004) (.126 – .136) 0.305 ±0.038 (.0120 ±.0015) TYP 16 0.50 (.0197) BSC 4.039 ±0.102 (.159 ±.004) (NOTE 3) RECOMMENDED SOLDER PAD LAYOUT 0.254 (.010) 0.35 REF 0.12 REF DETAIL “B” CORNER TAIL IS PART OF DETAIL “B” THE LEADFRAME FEATURE. FOR REFERENCE ONLY 9 NO MEASUREMENT PURPOSE 0.280 ±0.076 (.011 ±.003) REF 16151413121110 9 DETAIL “A” 0° – 6° TYP 3.00 ±0.102 (.118 ±.004) (NOTE 4) 4.90 ±0.152 (.193 ±.006) GAUGE PLANE 0.53 ±0.152 (.021 ±.006) DETAIL “A” 1.10 (.043) MAX 0.18 (.007) SEATING PLANE 0.17 – 0.27 (.007 – .011) TYP 1234567 8 0.50 (.0197) BSC NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX 6. EXPOSED PAD DIMENSION DOES INCLUDE MOLD FLASH. MOLD FLASH ON E-PAD SHALL NOT EXCEED 0.254mm (.010") PER SIDE. 0.86 (.034) REF 0.1016 ±0.0508 (.004 ±.002) MSOP (MSE16) 0911 REV E 3976f 26 For more information www.linear.com/3976 LT3976 Package Description Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. UDD Package 24-Lead Plastic QFN (3mm × 5mm) (Reference LTC DWG # 05-08-1833 Rev Ø) 0.70 ±0.05 3.50 ±0.05 2.10 ±0.05 3.65 ±0.05 1.50 REF 1.65 ±0.05 PACKAGE OUTLINE 0.25 ±0.05 0.50 BSC 3.50 REF 4.10 ±0.05 5.50 ±0.05 RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 3.00 ±0.10 0.75 ±0.05 1.50 REF 23 R = 0.05 TYP PIN 1 NOTCH R = 0.20 OR 0.25 × 45° CHAMFER 24 0.40 ±0.10 PIN 1 TOP MARK (NOTE 6) 5.00 ±0.10 1 2 3.65 ±0.10 3.50 REF 1.65 ±0.10 (UDD24) QFN 0808 REV Ø 0.200 REF 0.00 – 0.05 R = 0.115 TYP 0.25 ±0.05 0.50 BSC BOTTOM VIEW—EXPOSED PAD NOTE: 1. DRAWING IS NOT A JEDEC PACKAGE OUTLINE 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 3976f Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection its circuits as described herein will not infringe on existing patent rights. Forofmore information www.linear.com/3976 27 LT3976 Typical Application 1.2V Step-Down Converter DFLS160 VIN 4.3V TO 27V (40V TRANSIENT) 3.3V VIN OFF ON EN BOOST PG SW 10µF 10nF 2Ω LT3976 SS RT SYNC 0.47µF 2.2µH 470pF OUT VOUT 1.2V 5A FB GND 130k 3976 TA08 f = 400kHz D = PDS540 L = IHLP-2525CZ-01 47µF 1210 ×4 Related Parts PART NUMBER DESCRIPTION COMMENTS LT3480 36V with Transient Protection to 60V, 2A (IOUT), 2.4MHz, High Efficiency Step-Down DC/DC Converter with Burst Mode® Operation VIN = 3.6V to 38V, Transients to 60V, VOUT(MIN) = 0.78V, IQ = 70µA, ISD < 1µA, 3mm × 3mm DFN-10, MSOP-10E LT3980 58V with Transient Protection to 80V, 2A (IOUT), 2.4MHz, High Efficiency Step-Down DC/DC Converter with Burst Mode Operation VIN = 3.6V to 58V, Transients to 80V, VOUT(MIN) = 0.79V, IQ = 75µA, ISD < 1µA, 3mm × 4mm DFN-16, MSOP-16E LT3971 38V, 1.2A (IOUT), 2MHz, High Efficiency Step-Down DC/DC Converter with Only 2.8µA of Quiescent Current VIN = 4.2V to 38V, VOUT(MIN) = 1.2V, IQ = 2.8µA, ISD < 1µA, 3mm × 3mm DFN-10, MSOP-10E LT3991 55V, 1.2A (IOUT), 2MHz, High Efficiency Step-Down DC/DC Converter with Only 2.8µA of Quiescent Current VIN = 4.2V to 55V, VOUT(MIN) = 1.2V, IQ = 2.8µA, ISD < 1µA, 3mm × 3mm DFN-10, MSOP-10E LT3970 40V, 350mA (IOUT), 2MHz, High Efficiency Step-Down DC/DC Converter with Only 2.5µA of Quiescent Current VIN = 4.2V to 40V, VOUT(MIN) = 1.2V, IQ = 2.5µA, ISD < 0.7µA, 2mm × 3mm DFN-10, MSOP-10E LT3990 62V, 350mA (IOUT), 2.2MHz, High Efficiency Step-Down DC/DC Converter with Only 2.5µA of Quiescent Current VIN = 4.2V to 62V, VOUT(MIN) = 1.2V, IQ = 2.5µA, ISD < 0.7µA, 3mm × 3mm DFN-10, MSOP-16E 3976f 28 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 For more information www.linear.com/3976 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com/3976 LT 0113 • PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 2013