OPTOTRONIC® LED Power Supply Product Data Sheet OTe 50/220-240/1A0 CS FAN Constant Current LED Power Supply 700mA - 900mA - 1050mA ® OPTOTRONIC LED Power Supply with high efficiency and reliability in small compact housing. Equips with 3 selectable currents functionality fits in light fixtures for shop lighting. Benefits Three fixed selectable output currents Easy current selection Long lasting and high reliability Extra small compact housing Aux output 12V L B H 103mm 67mm 29.5 mm Applications Downlights, Spotlights, Tracklighting and other Indoor LED applications Approval marks Under preparation Product Features Output currents : 700/900/1050mA Ambient temp range,ta: -20°C to +50°C Output voltage : 27VDC – 54VDC Max. case temperature at tc point : 95°C Output power : 19W - 56W Galvanic isolation : 3.75kVrms Input voltage : 220 – 240 VAC Optional cable clamp is available Typ. Efficiency : ≥88% Suitable for class I and II luminaires Fixed Output (i.e. no dimming) 50’000 h lifetime at tc = 85°C Aux output 12V/100mA 1 Edition: 28 Jan 2014 Ver.: 1.0 Status: Released Misprints and technical changes excepted OPTOTRONIC® LED Power Supply OTe 50/220-240/1A0 CS FAN Product Data Sheet ENVIRONMENT DIMMING OUTPUT INPUT Electrical Specifications Item Nominal voltage Nominal frequency AC voltage range DC voltage range Maximum voltage Nominal current Total Harmonic Distortion (THD) Power factor Efficiency No-load power Stand-by power Power loss Protection class Inrush current Max. units per circuit breaker Touch current Nominal voltage range Maximum voltage Nominal current range Current accuracy Current ripple Nominal power range Aux output Maximum power (P LED + P aux.) Maximum power (P LED + P aux.) Galvanic isolation Dimming control Dimming range Dimming technique Frequency Galvanic isolation Ambient temperature range ta Value 220 – 240 50 - 60 198 – 264 NA 275 <300 < 20 0.95 > 88 < 1.5 NA 8.1 II <16 B16: 25; B10: 15 < 0.35 27 – 54 60 700 / 900 / 1050 +/- 5 < 35 19– 56 12 50 56.7 SELV-equivalent No NA NA NA NA -20 …+50 Maximum case temperature tc 95 Max. case temp. in fault condition Storage temperature range Relative humidity Surge transient protection Environmental rating IP rating Mains switching cycles 110 -25 …+75 5 ... 85 1 Indoor IP 20 > 100’000 35’000 50’000 Expected lifetime Unit VAC Hz VAC V V mA % % W W W A mA VDC VDC mA % % W V W W Remarks Permitted voltage range 2hrs 230V @ 56.7W load, Refer to Table 1 for details Full load, 230 V, 50 Hz / see graphs Full load, 230 V, 50 Hz / see graphs Full load, 230 V, 50 Hz, typical / see graphs 230V, typical at 230V input @ 50 W load max. Refer to Table 1 for details Suitable for class I and class II luminaires twidth = 100 µs typical (measured at 50% Ipeak) I max = 53 A Th = 230 μs Output floating Refer to Table 1 for details Open circuit Ripple / average @ 100 Hz, full load Partial Load. Refer to Table 1 for details 1.2 W Ta ≤ 50°C, Refer to Table 1 for details Ta ≤ 45°C, Refer to Table 1 for details 3,75 kVrms . Output to earth - Touch current < 0.7 mA/2 Not dimmable % Hz °C °C °C °C % kV hrs Refer to Table 1 for details Measured on tc point indicated of the product label. Refer to Table 1 for details Cool down before operating Not condensing L/N acc. IEC 61000-3-2 (ANSI C62.41 Cat.A …) tc = 95°C, 10% failure rate tc = 85°C, 10% failure rate Refer to Table 2 for details Protections Overtemperature Automatic, reversible Overload Automatic, reversible No load Yes Short-circuit Automatic, reversible Input overvoltage Maximum allowed input voltage 275V AC Output overvoltage Yes , Limitation of Output voltage < 60V Output undervoltage NA LED load protection NA Wiring Diagram 1 2 Terminal: Max. cable length - system: Geometry (l x b x h): Weight(typical): Push in terminals 2m 103 x 67 x 29.5 mm 188 g OTe 50/220-240/ 1A0 CS FAN 25 26 21 22 23 24 2 Fan 12V 100mA + LED-MODULE 1050mA 28W – 56W Example with 1050mA LED module Hot plug-in or secondary switching of LEDs is not permitted and may cause a very high current to the LEDs. 2 Edition: 28 Jan 2014 Ver.: 1.0 Status: Released Misprints and technical changes excepted OPTOTRONIC® LED Power Supply OTe 50/220-240/1A0 CS FAN Product Data Sheet Typical Operating Window Typical Efficiency over Load Typical Power factor over Load Typical THD over Load An optional cable clamp is available. This cable clamp can be snapped onto the ECG and thus converts it into an ECG suitable for independent installation. L L2 B B2 H 103mm 138mm 67mm 57,7mm 29,5 mm 3 Edition: 28 Jan 2014 Ver.: 1.0 Status: Released Misprints and technical changes excepted OPTOTRONIC® LED Power Supply OTe 50/220-240/1A0 CS FAN Table 1 - Rated output power and current sets Iout (mA) 700 900 1050 U min [V] 27 27 27 U max [V] 54 54 46 52 1 P min [W] 19 23 28 1 P max [W] 38 46 49 56 Ta [°C ] 50 50 50 45 Tc [°C ] 85 95 95 95 270 300 Line Current, nominal@230V mA 210 270 80 8.1 Max Power Loss@230V [W] 5.5 7.2 7.2 Input Power @230V [W] 56.6 Current selection by connect to right terminal 56.8 64.5 Fan 46.5 Product Data Sheet 1 + 25 26 Including auxiliary output ( P = P LED + P aux) Fan connection 12V/100mA Table 2 - Expected lifetime Tc [°C ] 85°C All Iout @ 50W max Ta [°C ] 40°C 95°C 50°C Lifetime 50’000h 35’000h Tc [°C ] Iout =1050mA @ 56.7W max 85°C 95°C Ta [°C ] Lifetime 35°C 50’000h 45°C 35’000h Standards Ordering information Safety: IEC 61347-1, IEC 61347-2-13 Performance: IEC 62384 Radio interference: CISPR 15 Harmonic content: IEC 61000-3-2 Immunity: IEC 61000-3-3 IEC 61547 Product name Type EAN10 EAN40 OTe 50/220-240/1A0 CS FAN AA62113 4052899919396 4052899919464 20 OT Cable Clamp B-style AA62261 NA 4052899077898 20 Pieces / box Disclaimer (Engineering Samples: B-Samples and C-Samples) This product is a demonstration model from our development laboratories made available for your information only. The model is not binding in respect to its fitness for use, i.e. service life, luminous flux, color temperature and performance. Prior to production the design, including dimensions, is subject to modification. You will, therefore, appreciate that at this stage of development we are unable to assume any liability also for damages which may be caused by this product. Should you urgently require binding information for the preparation of construction data for your applications, please contact our marketing department. Manufacturer’s address: Technical support: OSRAM GmbH Kunden Service Center Germany +49 (0)89-6213-60 00 Steinerne Furt 62 D-86167 Augsburg Germany www.osram.com 4 Edition: 28 Jan 2014 Ver.: 1.0 Status: Released Misprints and technical changes excepted