OPTOTRONIC® LED Power Supply Product Data Sheet OTe 13/220-240/350 PC Constant Current LED Power Supply 350mA – Phase Cut functionality ® OPTOTRONIC LED Power Supply with high efficiency and reliability in compact housing. Equipped with Phase Cut functionality fits in light fixtures for office and shop lighting. Benefits Suitable for use with electronic Leading and Trailing Edge dimmer Long lasting and high reliability Extra small compact housing Applications Downlights, Spotlights and other Indoor LED applications Approval marks L B H d 95mm 53mm 25 mm Φ 4,2 In preparation, if not printed on product labels Product Features Output currents : 350mA Ambient temp range ta: -20°C to +55°C Output voltage : 18VDC – 38VDC Max. case temperature at tc point : 85°C Output power : 6.5W – 13.5W Galvanic isolation : 3.75kVrms Input voltage : 220 – 240 VAC Optional cable clamp is available Typ. Efficiency : 84% Suitable for class I and II luminaires Phase Cut dimmable 50’000 h lifetime at tc = 75°C 1 Edition: 23 Feb. 2014 Ver.: 1.0 Status: Released Misprints and technical changes excepted OPTOTRONIC® LED Power Supply OTe 13/220-240/350 PC Product Data Sheet ENVIRONMENT DIMMING OUTPUT INPUT Electrical Specifications Item Nominal voltage Nominal frequency AC voltage range DC voltage range Maximum voltage Nominal current Total Harmonic Distortion (THD) Power factor Efficiency No-load power Stand-by power Power loss Input power Protection class Inrush current Max. units per circuit breaker Touch current Nominal voltage range Maximum voltage Nominal current range Current accuracy Current ripple Nominal power range Maximum power Galvanic isolation Value 220 – 240 50 - 60 198 – 264 NA 275 80 < 20 0.95 84 <1 NA 2.7 16.2 II <5 B16:130; B10:80 < 0.7 18 – 38 45 350 +/- 10 25 6.5 – 13.5 13.5 SELV-equivalent Dimming control Yes Dimming range Dimming technique 10 - 100 Ambient temperature range ta Maximum case temperature tc Max. Case temp. in fault condition Storage temperature range Relative humidity Surge transient protection Environmental rating IP rating Mains switching cycles -20 …+55 85 110 -25 …+75 5 ... 85 1|1 Indoor IP 20 > 100’000 35’000 50’000 Unit VAC Hz VAC V V mA % % W W W W A mA VDC VDC mA % % W W Remarks Permitted voltage range 2hrs 230V @ 13.5W load Full load, 230 V, 50 Hz / see graphs Full load, 230 V, 50 Hz / see graphs Full load, 230 V, 50 Hz, typical / see graphs 230V, typical at 230V input @ 13.5 W load max. at 230V input @ 13.5 W load max. Suitable for class I and class II luminaires twidth = 100 µs typical (measured at 50% Ipeak) I max = 0.08 A Th = 230 μs Output floating Open circuit typical Partial Load. Ta ≤ 55°C, 3,75 kVrms . Output to earth - Touch current < 0.7 mA Suitable for use with electronic leading- and trailing edge dimmer (Phase Cut) % Amplitude dimming Expected lifetime °C °C °C °C % kV Refer to Table 1 for details Measured on tc point indicated of the product label. hrs ta = 55°C , tc = 85°C, 10% failure rate ta = 45°C , tc = 75°C, 10% failure rate Cool down before operating Not condensing L/N | LN/PE acc. IEC 61000-3-2 (ANSI C62.41 Cat.A …) Protections Overtemperature Automatic, reversible Overload Automatic, reversible No load Yes Short-circuit Automatic, reversible Input overvoltage Maximum allowed input voltage 275V AC Output overvoltage Yes , Limitation of Output voltage < 60V Output undervoltage NA LED load protection NA Wiring Diagram Terminal: Max. cable length - system: Geometry (l x b x h): Weight(typical): Push in terminals 2m 95 x 53 x 25 mm 100 g Example with 500mA LED module Hot plug-in or secondary switching of LEDs is not permitted and may cause a very high current to the LEDs. 2 Edition: 23 Feb 2014 Ver.: 1.0 Status: Released Misprints and technical changes excepted OPTOTRONIC® LED Power Supply OTe 13/220-240/350 PC Typical Operating window Product Data Sheet Typical Efficiency over load Operation Window Efficiency vs load 40.0 85 80 75 Efficiency [%] output voltage (V) 35.0 30.0 25.0 70 65 60 20.0 55 15.0 150 250 350 450 50 550 5 Output current (mA) 9 13 Output Power [W] Typical Power factor over load Typical THD over load Power Factor vs load THD vs load 1.0 35 30 25 0.8 THD [%] Power Factor 0.9 0.7 20 15 0.6 10 0.5 5 5 9 13 Output Power [W] 5 9 13 Output Power [W] An optional cable clamp is available. This cable clamp can be snapped onto the ECG and thus converts it into an ECG suitable for independent installation. L 95mm L2 119mm B 53mm H 25mm d Φ 4,2 3 Edition: 23 Feb 2014 Ver.: 1.0 Status: Released Misprints and technical changes excepted OPTOTRONIC® LED Power Supply OTe 13/220-240/350 PC Product Data Sheet Standards Safety: IEC 61347-1, IEC 61347-2-13 Performance: IEC 62384 Radio interference: CISPR 15 Harmonic content: IEC 61000-3-2 Immunity: IEC 61000-3-3 IEC 61547 Product name OTE 13/220-240/350 PC OT Cable Clamp E-style EAN10 4052899105324 4052899167896 Manufacturer’s address: Technical support: OSRAM GmbH Kunden Service Center Germany +49 (0)89-6213-60 00 EAN40 4052899105331 4052899095861 Pieces / box 20 20 Steinerne Furt 62 D-86167 Augsburg Germany www.osram.com 4 Edition: 23 Feb 2014 Ver.: 1.0 Status: Released Misprints and technical changes excepted