OPTOTRONIC® LED Power Supply Product Data Sheet OTe 10/220-240/700 PC Constant Current LED Power Supply 700mA – PhaseCut functionality ® OPTOTRONIC LED Power Supply with high efficiency and reliability in compact housing. Equipped with Phase Cut functionality fits in light fixtures for office and shop lighting. Benefits Suitable for use with electronic Leading and Trailing Edge dimmer Long lasting and high reliability Extra small compact housing Applications Downlights, Spotlights and other Indoor LED applications Approval marks L B H d In preparation, if not printed on product labels 95mm 53mm 25 mm Φ 4,2 Under preparation Product Features Output currents : 700mA Ambient temp range ta: -20°C to +55°C Output voltage : 7VDC – 14VDC Max. case temperature at tc point : 80°C Output power : 5W - 10W Galvanic isolation : 3.75kVrms Input voltage : 220 – 240 VAC Optional cable clamp is available Typ. Efficiency : 79% Suitable for class I and II luminaires Phase Cut dimmable 50’000 h lifetime at tc = 70°C 1 Edition: 22 Feb 2014 Ver.: 0.2 Status: Draft Misprints and technical changes excepted OPTOTRONIC® LED Power Supply OTe 10/220-240/700 PC Product Data Sheet ENVIRONMENT DIMMING OUTPUT INPUT Electrical Specifications Item Nominal voltage Nominal frequency AC voltage range DC voltage range Maximum voltage Nominal current Total Harmonic Distortion (THD) Power factor Efficiency No-load power Stand-by power Power loss Input power Protection class Inrush current Max. units per circuit breaker Touch current Nominal voltage range Maximum voltage Nominal current range Current accuracy Current ripple Nominal power range Maximum power Galvanic isolation Value 220 – 240 50 - 60 198 – 264 NA 275 65 < 20 0.95 79 <1 NA 2.8 12.8 II <5 Dimming control Yes Dimming range Dimming technique 10 - 100 Ambient temperature range ta Maximum case temperature tc Max. case temp. in fault condition Storage temperature range Relative humidity Surge transient protection Environmental rating IP rating Mains switching cycles -20 …+55 80 110 -25 …+75 5 ... 85 1|1 Indoor IP 20 > 100’000 35’000 50’000 Unit VAC Hz VAC V V mA % % W W W W A B16:160; B10:100 < 0.7 7 – 14 22 700 +/- 10 35 5 – 10 10 SELV-equivalent mA VDC VDC mA % % W W Remarks Permitted voltage range 2hrs 230V @ 10W load Full load, 230 V, 50 Hz / see graphs Full load, 230 V, 50 Hz / see graphs Full load, 230 V, 50 Hz, typical / see graphs 230V, typical at 230V input @ 10 W load max. at 230V input @ 10 W load max. Suitable for class I and class II luminaires twidth = 100 µs typical (measured at 50% Ipeak) I max = 0.065 A Th = 230 μs Output floating Open circuit typical Partial Load. Ta ≤ 55°C, 3,75 kVrms . Output to earth - Touch current < 0.7 mA Suitable for use with electronic leading- and trailing edge dimmer (Phase Cut) % Amplitude dimming Expected lifetime °C °C °C °C % kV Refer to Table 1 for details Measured on tc point indicated of the product label. hrs ta = 55°C , tc = 80°C, 10% failure rate ta = 45°C , tc = 70°C, 10% failure rate Cool down before operating Not condensing L/N | LN/PE acc. IEC 61000-3-2 (ANSI C62.41 Cat.A …) Protections Overtemperature Automatic, reversible Overload Automatic, reversible No load Yes Short-circuit Automatic, reversible Input overvoltage Maximum allowed input voltage 275V AC Output overvoltage Yes , Limitation of Output voltage < 60V Output undervoltage NA LED load protection NA Wiring Diagram Terminal: Max. cable length - system: Geometry (l x b x h): Weight(typical): Push in terminals 2m 95 x 53 x 25 mm 100 g Example with 800mA LED module Hot plug-in or secondary switching of LEDs is not permitted and may cause a very high current to the LEDs. 2 Edition: 23 Feb. 2014 Ver.: 1.0 Status: released Misprints and technical changes excepted OPTOTRONIC® LED Power Supply OTe 10/220-240/700 PC Typical Operating window Product Data Sheet Typical Efficiency over load Operation Window Efficiency vs load 80 Efficiency [%] output voltage (V) 14.0 11.0 70 60 8.0 50 5.0 500 600 700 800 4 900 5 6 7 8 9 10 11 Output Power [W] Output current (mA) Typical Power factor over load Typical THD over load THD vs load Power Factor vs load 35 1.00 30 0.90 THD [%] Power Factor 25 0.80 0.70 20 15 0.60 10 5 0.50 4 5 6 7 8 9 10 Output Power [W] 11 4 5 6 7 8 9 10 11 Output Power [W] An optional cable clamp is available. This cable clamp can be snapped onto the ECG and thus converts it into an ECG suitable for independent installation. L 95mm L2 119mm B 53mm H 25mm d Φ 4,2 3 Edition: 23 Feb. 2014 Ver.: 1.0 Status: released Misprints and technical changes excepted OPTOTRONIC® LED Power Supply OTe 10/220-240/700 PC Product Data Sheet Standards Safety: IEC 61347-1, IEC 61347-2-13 Performance: IEC 62384 Radio interference: CISPR 15 Harmonic content: IEC 61000-3-2 Immunity: IEC 61000-3-3 IEC 61547 Product name EAN10 EAN40 OTE 10/220-240/700 PC OT Cable Clamp E-style 4052899105300 4052899167896 4052899105317 4052899095861 Manufacturer’s address: Technical support: OSRAM GmbH Kunden Service Center Germany +49 (0)89-6213-60 00 Pieces / box 20 20 Steinerne Furt 62 D-86167 Augsburg Germany www.osram.com 4 Edition: 23 Feb. 2014 Ver.: 1.0 Status: released Misprints and technical changes excepted