View detail for Appendix B - ATtiny24A/44A/84A Specification at 125°C

ATtiny24A, ATtiny44A, ATtiny84A
8-bit AVR Microcontroller with
2K/4K/8K Bytes In-System Programmable Flash
DATASHEET APPENDIX B
Appendix B – ATtiny24A/44A/84A Specification at 125°C
This document contains information specific to devices operating at temperatures up to
125°C. Only deviations are covered in this appendix, all other information can be found
in the complete datasheet. The complete datasheet can be found at www.atmel.com.
8183H–AVR–10/2013
1.
Memories
1.1
EEPROM Data Memory
The EEPROM has an endurance of at least 50,000 write/erase cycles.
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
2
2.
Electrical Characteristics
2.1
Absolute Maximum Ratings*
Operating Temperature . . . . . . . . . . . -55C to +125C
*NOTICE:
Storage Temperature . . . . . . . . . . . . . -65C to +150C
Voltage on any Pin except RESET
with respect to Ground. . . . . . . . . . -0.5V to VCC+0.5V
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these
or other conditions beyond those indicated in
the operational sections of this specification is
not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Voltage on RESET with respect to Ground-0.5V to +13.0V
Maximum Operating Voltage . . . . . . . . . . . . . . . . 6.0V
DC Current per I/O Pin. . . . . . . . . . . . . . . . . . 40.0 mA
DC Current VCC and GND Pins . . . . . . . . . . 200.0 mA
2.2
DC Characteristics
Table 2-1.
Symbol
DC Characteristics. TA = -40°C to +125°C
Parameter
Input Low Voltage
VIL
Input Low Voltage,
RESET Pin as Reset (4)
Input High-voltage
Except RESET pin
VIH
Input High-voltage
RESET pin as Reset (4)
Condition
Min
VCC = 1.8V - 2.4V
Typ(1)
Max
Units
-0.5
0.2VCC(3)
V
VCC = 2.4V - 5.5V
-0.5
0.3VCC(3)
V
VCC = 1.8V - 5.5
-0.5
0.2VCC(3)
VCC = 1.8V - 2.4V
0.7VCC(2)
VCC +0.5
V
VCC = 2.4V - 5.5V
0.6VCC(2)
VCC +0.5
V
VCC = 1.8V to 5.5V
0.9VCC(2)
VCC +0.5
V
Output Low Voltage (5)
Except RESET pin (7)
IOL = 10 mA, VCC = 5V
0.6
V
VOL
IOL = 5 mA, VCC = 3V
0.5
V
Output High-voltage (6)
Except RESET pin (7)
IOH = -10 mA, VCC = 5V
4.3
V
VOH
IOH = -5 mA, VCC = 3V
2.5
V
ILIL
Input Leakage
Current I/O Pin
Vcc = 5.5V, pin low
(absolute value)
< 0.05
1 (8)
µA
ILIH
Input Leakage
Current I/O Pin
Vcc = 5.5V, pin high
(absolute value)
< 0.05
1 (8)
µA
Pull-up Resistor, I/O Pin
VCC = 5.5V, input low
20
50
k
Pull-up Resistor, Reset Pin
VCC = 5.5V, input low
30
60
k
RPU
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
3
Symbol
Parameter
Supply Current,
Active Mode (9)
ICC
Supply Current,
Idle Mode (9)
Supply Current,
Power-Down Mode (10)
Typ(1)
Max
Units
f = 1MHz, VCC = 2V
0.25
0.5
mA
f = 4MHz, VCC = 3V
1.2
2
mA
f = 8MHz, VCC = 5V
4.4
7
mA
f = 1MHz, VCC = 2V
0.04
0.2
mA
f = 4MHz, VCC = 3V
0.25
0.6
mA
f = 8MHz, VCC = 5V
1.3
2
mA
WDT enabled, VCC = 3V
4
20
µA
WDT disabled, VCC = 3V
0.2
10
µA
Condition
Min
Notes: 1. Typical values at 25C.
2. “Min” means the lowest value where the pin is guaranteed to be read as high.
3. “Max” means the highest value where the pin is guaranteed to be read as low.
4. Not tested in production.
5. Although each I/O port can sink more than the test conditions (10 mA at VCC = 5V, 5 mA at VCC = 3V) under steady
state conditions (non-transient), the sum of all IOL (for all ports) should not exceed 60 mA. If IOL exceeds the test conditions, VOL may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test
condition.
6. Although each I/O port can source more than the test conditions (10 mA at VCC = 5V, 5 mA at VCC = 3V) under steady
state conditions (non-transient), the sum of all IOH (for all ports) should not exceed 60 mA. If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current greater than the listed test
condition.
7. The RESET pin must tolerate high voltages when entering and operating in programming modes and, as a consequence, has a weak drive strength as compared to regular I/O pins. See figures, for ATtiny24A, from Figure 3-22 on
page 21 to Figure 3-25 on page 23, and for ATtiny44A, from Figure 3-67 on page 44 to Figure 3-70 on page 45.
8. These are test limits, which account for leakage currents of the test environment. Actual device leakage currents are
lower.
9. Values are with external clock using methods described in “Minimizing Power Consumption”. Power reduction is
enabled (PRR = 0xFF) and there is no I/O drive.
10. BOD disabled.
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
4
2.3
Speed
2.3.1
ATtiny24A and ATtiny44A
The maximum operating frequency of the device depends on VCC. As shown in Figure 2-1, the relationship between
maximum frequency and VCC is linear in the region 1.8V < VCC < 4.5V.
Figure 2-1. Maximum Frequency vs. VCC. TA = -40C to +125C
20 MHz
4 MHz
4.5V
1.8V
2.3.2
5.5V
ATtiny84A
The maximum operating frequency of the device depends on VCC. As shown in Figure 2-1, the relationship between
maximum frequency and VCC is linear in the region 1.8V < VCC < 4.5V.
Figure 2-2. Maximum Frequency vs. VCC. TA = -40C to +125C
16 MHz
4 MHz
1.8V
4.5V
5.5V
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
5
2.4
Clock Characteristics
2.4.1
Accuracy of Calibrated Internal Oscillator
It is possible to manually calibrate the internal oscillator to be more accurate than default factory calibration. Note that
oscillator frequency depends on temperature and voltage. Voltage and temperature characteristics can be found in
Figure 3-45 on page 33.
Table 2-2.
Calibration Accuracy of Internal RC Oscillator
Calibration Method
Target Frequency
VCC
Temperature
Accuracy at given
voltage & temperature(1)
8.0 MHz
3V
25C
±10%
Fixed frequency:
7.3 – 8.1 MHz
Fixed voltage:
1.8V – 5.5V
Fixed temperature:
-40C to +125C
±1%
Factory Calibration
User Calibration
Note:
1.
Accuracy of oscillator frequency at calibration point (fixed temperature and fixed voltage).
2.5
System and Reset Characteristics
2.5.1
Power-On Reset
Table 2-3.
Characteristics of Enhanced Power-On Reset. TA = -40 to +125°C
Symbol
Parameter
Release threshold of power-on reset (2)
VPOR
VPOA
Activation threshold of power-on reset
SRON
Power-On Slope Rate
Notes: 1.
2.6
(3)
Min(1)
Typ(1)
Max(1)
Units
1.1
1.4
1.7
V
0.6
1.3
1.7
V
0.01
V/ms
Values are guidelines, only
2.
Threshold where device is released from reset when voltage is rising
3.
The Power-on Reset will not work unless the supply voltage has been below VPOA
Analog Comparator Characteristics
Table 2-4.
Analog Comparator Characteristics, TA = -40°C to +125°C
Symbol
Parameter
Condition
VAIO
Input Offset Voltage
VCC = 5V, VIN = VCC / 2
ILAC
Input Leakage Current
VCC = 5V, VIN = VCC / 2
Analog Propagation Delay
(from saturation to slight overdrive)
VCC = 2.7V
750
VCC = 4.0V
500
Analog Propagation Delay
(large step change)
VCC = 2.7V
100
VCC = 4.0V
75
Digital Propagation Delay
VCC = 1.8V - 5.5
1
tAPD
tDPD
Note:
Min
Typ
Max
Units
< 10
40
mV
0.5
µA
-0.5
ns
2
CLK
All parameters are based on simulation results and are not tested in production
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
6
2.7
ADC Characteristics
Table 2-5.
Symbol
ADC Characteristics, Single Ended Channels. T = -40°C to +125°C
Parameter
Condition
Min
Typ
Resolution
Units
10
Bits
VREF = 4V, VCC = 4V,
ADC clock = 200 kHz
2.0
LSB
VREF = 4V, VCC = 4V,
ADC clock = 1 MHz
2.5
LSB
1.5
LSB
VREF = 4V, VCC = 4V,
ADC clock = 1 MHz
Noise Reduction Mode
2.0
LSB
Integral Non-Linearity (INL)
(Accuracy after Offset and
Gain Calibration)
VREF = 4V, VCC = 4V,
ADC clock = 200 kHz
1.0
LSB
Differential Non-linearity
(DNL)
VREF = 4V, VCC = 4V,
ADC clock = 200 kHz
0.5
LSB
Gain Error
VREF = 4V, VCC = 4V,
ADC clock = 200 kHz
2.0
LSB
Offset Error (Absolute)
VREF = 4V, VCC = 4V,
ADC clock = 200 kHz
1.5
LSB
Conversion Time
Free Running Conversion
Absolute accuracy
(Including INL, DNL, and
Quantization, Gain and Offset
Errors)
Clock Frequency
VIN
Max
Input Voltage
VREF = 4V, VCC = 4V,
ADC clock = 200 kHz
Noise Reduction Mode
14
280
µs
50
1000
kHz
GND
VREF
V
Input Bandwidth
38.5
kHz
AREF
External Voltage Reference
2.0
VINT
Internal Voltage Reference
1.0
RREF
Reference Input Resistance
32
k
RAIN
Analog Input Resistance
100
M
ADC Conversion Output
0
1.1
VCC
V
1.2
V
1023
LSB
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
7
Table 2-6.
Symbol
ADC Characteristics, Differential Channels (Unipolar Mode), TA = -40°C to +125°C
Parameter
Condition
Min
Typ
Max
Units
Gain = 1x
10
Bits
Gain = 20x
10
Bits
Resolution
Absolute accuracy
(Including INL, DNL, and Quantization, Gain
and Offset Errors)
Integral Non-Linearity (INL)
(Accuracy after Offset and Gain Calibration)
Gain = 1x
VREF = 4V, VCC = 5V
ADC clock = 50 - 200 kHz
10
LSB
Gain = 20x
VREF = 4V, VCC = 5V
ADC clock = 50 - 200 kHz
15
LSB
Gain = 1x
VREF = 4V, VCC = 5V
ADC clock = 50 - 200 kHz
4
LSB
Gain = 20x
VREF = 4V, VCC = 5V
ADC clock = 50 - 200 kHz
10
LSB
Gain = 1x
10
LSB
Gain = 20x
15
LSB
Gain = 1x
VREF = 4V, VCC = 5V
ADC clock = 50 - 200 kHz
3
LSB
Gain = 20x
VREF = 4V, VCC = 5V
ADC clock = 50 - 200 kHz
4
LSB
Gain Error
Offset Error
Conversion Time
Clock Frequency
VIN
Input Voltage
VDIFF
Input Differential Voltage
Free Running Conversion
70
280
µs
50
200
kHz
GND
VCC
V
VREF/Gain
V
4
Input Bandwidth
kHz
AREF
External Reference Voltage
2.0
VINT
Internal Voltage Reference
1.0
RREF
Reference Input Resistance
32
k
RAIN
Analog Input Resistance
100
M
ADC Conversion Output
0
1.1
VCC - 1.0
V
1.2
V
1023
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
LSB
8
Table 2-7.
Symbol
ADC Characteristics, Differential Channels (Bipolar Mode), TA = -40°C to +125°C
Parameter
Condition
Min
Typ
Max
Units
Gain = 1x
10
Bits
Gain = 20x
10
Bits
Resolution
Absolute accuracy
(Including INL, DNL, and Quantization, Gain
and Offset Errors)
Integral Non-Linearity (INL)
(Accuracy after Offset and Gain Calibration)
Gain = 1x
VREF = 4V, VCC = 5V
ADC clock = 50 - 200 kHz
8
LSB
Gain = 20x
VREF = 4V, VCC = 5V
ADC clock = 50 - 200 kHz
8
LSB
Gain = 1x
VREF = 4V, VCC = 5V
ADC clock = 50 - 200 kHz
4
LSB
Gain = 20x
VREF = 4V, VCC = 5V
ADC clock = 50 - 200 kHz
5
LSB
Gain = 1x
4
LSB
Gain = 20x
5
LSB
Gain = 1x
VREF = 4V, VCC = 5V
ADC clock = 50 - 200 kHz
3
LSB
Gain = 20x
VREF = 4V, VCC = 5V
ADC clock = 50 - 200 kHz
4
LSB
Gain Error
Offset Error
Conversion Time
Clock Frequency
VIN
Input Voltage
VDIFF
Input Differential Voltage
Free Running Conversion
70
280
µs
50
200
kHz
GND
VCC
V
VREF/Gain
V
4
Input Bandwidth
kHz
AREF
External Reference Voltage
2.0
VINT
Internal Voltage Reference
1.0
RREF
Reference Input Resistance
32
k
RAIN
Analog Input Resistance
100
M
ADC Conversion Output
-512
1.1
VCC - 1.0
V
1.2
V
511
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
LSB
9
2.8
Serial Programming Characteristics
2.8.1
ATtiny24A and ATtiny44A
Table 2-8.
Symbol
1/tCLCL
tCLCL
1/tCLCL
Serial Programming Characteristics, TA = -40°C to +125°C, VCC = 1.8 - 5.5V (Unless Otherwise Noted)
Parameter
Oscillator Frequency
Oscillator Period
Min
Typ
0
Max
Units
4
MHz
250
ns
Oscillator Frequency (VCC = 4.5V - 5.5V)
0
tCLCL
Oscillator Period (VCC = 4.5V - 5.5V)
50
ns
tSHSL
SCK Pulse Width High
2 tCLCL(1)
ns
tSLSH
SCK Pulse Width Low
2 tCLCL(1)
ns
tOVSH
MOSI Setup to SCK High
tCLCL
ns
tSHOX
MOSI Hold after SCK High
2 tCLCL
ns
Note:
1. 2 tCLCL for fck < 12 MHz, 3 tCLCL for fck >= 12 MHz
2.8.2
ATtiny84A
Table 2-9.
Symbol
1/tCLCL
tCLCL
1/tCLCL
20
MHz
Serial Programming Characteristics, TA = -40°C to +125°C, VCC = 1.8 - 5.5V (Unless Otherwise Noted)
Parameter
Oscillator Frequency
Oscillator Period
Oscillator Frequency (VCC = 4.5V - 5.5V)
tCLCL
Oscillator Period (VCC = 4.5V - 5.5V)
tSHSL
Min
0
Typ
Max
Units
4
MHz
250
0
ns
16
MHz
62.5
ns
SCK Pulse Width High
2 tCLCL(1)
ns
tSLSH
SCK Pulse Width Low
2 tCLCL(1)
ns
tOVSH
MOSI Setup to SCK High
tCLCL
ns
tSHOX
MOSI Hold after SCK High
2 tCLCL
ns
Note:
1. 2 tCLCL for fck < 12 MHz, 3 tCLCL for fck >= 12 MHz
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
10
3.
Typical Characteristics
3.1
ATtiny24A
3.1.1
Current Consumption in Active Mode
Figure 3-1. Active Supply Current vs. VCC (Internal RC Oscillator, 8 MHz)
6
125 °C
5
85 °C
25 °C
-40 °C
ICC (mA)
4
3
2
1
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Figure 3-2. Active Supply Current vs. VCC (Internal RC Oscillator, 1 MHz)
1,2
125 °C
85 °C
25 °C
-40 °C
1
ICC (mA)
0,8
0,6
0,4
0,2
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
11
Figure 3-3. Active Supply Current vs. VCC (Internal RC Oscillator, 128 kHz)
0,14
0,12
125 °C
-40 °C
25 °C
85 °C
ICC (mA)
0,1
0,08
0,06
0,04
0,02
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Current Consumption in Idle Mode
Figure 3-4. Idle Supply Current vs. VCC (Internal RC Oscillator, 8 MHz)
2
1,8
1,6
1,4
125 °C
85 °C
25 °C
-40 °C
1,2
ICC (mA)
3.1.2
1
0,8
0,6
0,4
0,2
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
12
Figure 3-5. Idle Supply Current vs. VCC (Internal RC Oscillator, 1 MHz)
0,4
0,35
125 °C
85 °C
25 °C
-40 °C
0,3
ICC (mA)
0,25
0,2
0,15
0,1
0,05
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Figure 3-6. Idle Supply Current vs. VCC (Internal RC Oscillator, 128 kHz)
0,03
125 °C
0,025
-40 °C
25 °C
85 °C
ICC (mA)
0,02
0,015
0,01
0,005
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
13
Current Consumption in Power-down Mode
Figure 3-7. Power-down Supply Current vs. VCC (Watchdog Timer Disabled)
5
125 °C
4
ICC (uA)
3
2
1
85 °C
25 °C
-40 °C
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Figure 3-8. Power-down Supply Current vs. VCC (Watchdog Timer Enabled)
12
125 °C
10
8
ICC (uA)
3.1.3
-40 °C
25 °C
85 °C
6
4
2
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
14
Current Consumption of Peripheral Units
Figure 3-9. Programming Current vs. VCC
10000
9000
-40 °C
8000
7000
ICC (uA)
6000
25 °C
5000
85 °C
4000
125 °C
3000
2000
1000
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Figure 3-10. Brownout Detector Current vs. VCC (BOD Level = 1.8V)
45
40
35
30
ICC (uA)
3.1.4
125 °C
85 °C
25 °C
-40 °C
25
20
15
10
5
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
15
Figure 3-11. Watchdog Timer Current vs. VCC
8
-40 °C
7
25 °C
85 °C
125 °C
6
ICC (uA)
5
4
3
2
1
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Pull-up Resistors
Figure 3-12. Pull-up Resistor Current vs. Input Voltage (I/O Pin, VCC = 1.8V)
60
50
40
IOP (uA)
3.1.5
30
20
10
25 °C
-40 °C
85 °C
125 °C
0
0
0,5
1
1,5
2
VOP (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
16
Figure 3-13. Pull-up Resistor Current vs. Input Voltage (I/O Pin, VCC = 2.7V)
80
70
60
IOP (uA)
50
40
30
20
25 °C
10
-40 °C
85 °C
125 °C
0
0
0,5
1
1,5
2
2,5
3
VOP (V)
Figure 3-14. Pull-up Resistor Current vs. Input Voltage (I/O Pin, VCC = 5V)
160
140
120
IOP (uA)
100
80
60
40
25 °C
85 °C
-40 °C
125 °C
20
0
0
1
2
3
4
5
VOP (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
17
Figure 3-15. Reset Pull-up Resistor Current vs. Reset Pin Voltage (VCC = 1.8V)
40
35
30
IRESET (uA)
25
20
15
10
25 °C
-40 °C
85 °C
125 °C
5
0
0
0,2
0,4
0,6
0,8
1
1,2
1,4
1,6
1,8
2
VRESET (V)
Figure 3-16. Reset Pull-up Resistor Current vs. Reset Pin Voltage (VCC = 2.7V)
60
50
IRESET (uA)
40
30
20
10
25 °C
-40 °C
85 °C
125 °C
0
0
0,5
1
1,5
2
2,5
3
VRESET (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
18
Figure 3-17. Reset Pull-up Resistor Current vs. Reset Pin Voltage (VCC = 5V)
120
100
IRESET (uA)
80
60
40
20
25 °C
-40 °C
85 °C
125 °C
0
0
1
2
3
4
5
6
VRESET (V)
Output Driver Strength
Figure 3-18. VOL: Output Voltage vs. Sink Current (I/O Pin, VCC = 1.8V)
0,5
125 °C
0,4
85 °C
0,3
25 °C
VOL (V)
3.1.6
-40 °C
0,2
0,1
0
0
1
2
3
4
5
IOL (mA)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
19
Figure 3-19. VOL: Output Voltage vs. Sink Current (I/O Pin, VCC = 3V)
0,5
125 °C
0,4
85 °C
25 °C
VOL (V)
0,3
-40 °C
0,2
0,1
0
0
2
4
6
8
10
IOL (mA)
Figure 3-20. VOL: Output Voltage vs. Sink Current (I/O Pin, VCC = 5V)
0,7
125 °C
0,6
85 °C
VOL (V)
0,5
25 °C
0,4
-40 °C
0,3
0,2
0,1
0
0
5
10
15
20
IOL (mA)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
20
Figure 3-21. VOH: Output Voltage vs. Source Current (I/O Pin, VCC = 1.8V)
1,8
1,7
VOH (V)
1,6
1,5
-40 °C
25 °C
1,4
85 °C
125 °C
1,3
0
1
2
3
4
5
IOH (mA)
Figure 3-22. VOH: Output Voltage vs. Source Current (I/O Pin, VCC = 3V)
3
2,9
VOH (V)
2,8
-40 °C
2,7
25 °C
2,6
85 °C
125 °C
2,5
0
2
4
6
8
10
IOH (mA)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
21
Figure 3-23. VOH: Output Voltage vs. Source Current (I/O Pin, VCC = 5V)
5
4,9
VOH (V)
4,8
4,7
4,6
-40 °C
4,5
25 °C
85 °C
4,4
125 °C
4,3
0
10
5
15
20
IOH (mA)
Figure 3-24. VOL: Output Voltage vs. Sink Current (Reset Pin as I/O, VCC = 3V)
2
125 °C
1,6
1,2
VOL (V)
85 °C
25 °C
0,8
-40 °C
0,4
0
0
0,5
1
1,5
2
2,5
3
IOL (mA)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
22
Figure 3-25. VOL: Output Voltage vs. Sink Current (Reset Pin as I/O, VCC = 5V)
1,2
125 °C
1
85 °C
VOL (V)
0,8
25 °C
0,6
-40 °C
0,4
0,2
0
0
1
2
3
4
5
IOL (mA)
Figure 3-26. VOH: Output Voltage vs. Source Current (Reset Pin as I/O, VCC = 3V)
3
2,5
VOH (V)
2
1,5
-40 °C
25 °C
85 °C
125 °C
1
0,5
0
0
0,4
0,8
1,2
1,6
IOH (mA)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
23
Figure 3-27. VOH: Output Voltage vs. Source Current (Reset Pin as I/O, VCC = 5V)
5
4
3
VOH (V)
-40 °C
25 °C
85 °C
125 °C
2
1
0
0
0,4
0,8
1,2
1,6
IOH (mA)
Input Threshold and Hysteresis (for I/O Ports)
Figure 3-28. VIH: Input Threshold Voltage vs. VCC (IO Pin, Read as ‘1’)
3,5
125 °C
85 °C
25 °C
-40 °C
3
2,5
Threshold (V)
3.1.7
2
1,5
1
0,5
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
24
Figure 3-29. VIL: Input Threshold Voltage vs. VCC (I/O Pin, Read as ‘0’)
2,5
125 °C
85 °C
25 °C
-40 °C
Threshold (V)
2
1,5
1
0,5
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
4
4,5
5
5,5
VCC (V)
Figure 3-30. VIH-VIL: Input Hysteresis vs. VCC (I/O Pin)
0,8
0,7
Input Hysteresis (V)
0,6
-40 °C
0,5
25 °C
0,4
0,3
85 °C
125 °C
0,2
0,1
0
1,5
2
2,5
3
3,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
25
Figure 3-31. VIH: Input Threshold Voltage vs. VCC (Reset Pin as I/O, Read as ‘1’)
5
4,5
4
Threshold (V)
3,5
125 °C
85 °C
25 °C
-40 °C
3
2,5
2
1,5
1
0,5
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Figure 3-32. VIL: Input Threshold Voltage vs. VCC (Reset Pin as I/O, Read as ‘0’)
2,5
125 °C
85 °C
25 °C
-40 °C
Threshold (V)
2
1,5
1
0,5
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
26
Figure 3-33. VIH-VIL: Input Hysteresis vs. VCC (Reset Pin as I/O)
1
0,9
0,8
Input Hysteresis (V)
0,7
-40 °C
0,6
0,5
0,4
25 °C
85 °C
125 °C
0,3
0,2
0,1
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
BOD, Bandgap and Reset
Figure 3-34. BOD Threshold vs. Temperature (BODLEVEL is 4.3V)
4,4
4,38
4,36
Threshold (V)
3.1.8
VCC RISING
4,34
4,32
4,3
VCC FALLING
4,28
4,26
-40
-20
0
20
40
60
80
100
120
140
Temperature (C)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
27
Figure 3-35. BOD Threshold vs. Temperature (BODLEVEL is 2.7V)
2,8
2,78
VCC RISING
Threshold (V)
2,76
2,74
2,72
2,7
VCC FALLING
2,68
2,66
-40
-20
0
20
40
60
80
100
120
140
Temperature (C)
Figure 3-36. BOD Threshold vs. Temperature (BODLEVEL is 1.8V)
1,86
1,85
Threshold (V)
1,84
VCC RISING
1,83
1,82
1,81
VCC FALLING
1,8
1,79
-40
-20
0
20
40
60
80
100
120
140
Temperature (C)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
28
Figure 3-37. Bandgap Voltage vs. Temperature (VCC = 5V)
1,12
Bandgap Voltage (V)
1,11
1,1
1,09
1,08
1,07
1,06
-40
-20
0
20
40
60
80
100
120
140
Temperature
Figure 3-38. VIH: Input Threshold Voltage vs. VCC (Reset Pin, Read as ‘1’)
2,5
-40 °C
25 °C
85 °C
125 °C
Threshold (V)
2
1,5
1
0,5
0
1
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
29
Figure 3-39. VIL: Input Threshold Voltage vs. VCC (Reset Pin, Read as ‘0’)
2,5
125 °C
85 °C
25 °C
-40 °C
Threshold (V)
2
1,5
1
0,5
0
1
1,5
2
2,5
3
3,5
4
4,5
5
5,5
3,5
4
4,5
5
5,5
VCC (V)
Figure 3-40. VIH-VIL: Input Hysteresis vs. VCC (Reset Pin)
1
0,9
0,8
Input Hysteresis (V)
0,7
-40 °C
0,6
0,5
25 °C
0,4
0,3
85 °C
0,2
125 °C
0,1
0
1
1,5
2
2,5
3
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
30
Figure 3-41. Minimum Reset Pulse Width vs. VCC
MINIMUM RESET PULSE WIDTH vs. V CC
1800
1600
1400
Pulsewidth (ns)
1200
1000
800
600
125 °C
85 °C
25 °C
-40 °C
400
200
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Analog Comparator Offset
Figure 3-42. Analog Comparator Offset (VCC = 5V)
0,004
0,002
0
0
Offset (V)
3.1.9
0,5
1
1,5
2
2,5
3
3,5
4
4,5
5
-0,002
-0,004
-40 °C
25 °C
85 °C
125 °C
-0,006
-0,008
-0,01
Vin (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
31
3.1.10 Internal Oscillator Speed
Figure 3-43. Watchdog Oscillator Frequency vs. VCC
126
124
122
Frequency (kHz)
-40 °C
120
25 °C
118
116
114
85 °C
112
125 °C
110
108
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Figure 3-44. Watchdog Oscillator Frequency vs. Temperature
126
124
Frequency (kHz)
122
120
118
1.8 V
116
114
3.0 V
112
5.0 V
110
108
-40
-20
0
20
40
60
80
100
120
140
Temperature
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
32
Figure 3-45. Calibrated 8 MHz RC Oscillator Frequency vs. Temperature
8,4
Frequency (MHz)
5.0 V
8,3
3.0 V
8,2
1.8 V
8,1
8
7,9
7,8
7,7
7,6
7,5
-40
-20
0
20
40
60
80
100
120
140
Temperature
Figure 3-46. Calibrated 8 MHz RC Oscillator Frequency vs. OSCCAL Value (VCC = 3V)
20
125 °C
85 °C
25 °C
-40 °C
16
FRC (MHz)
12
8
4
0
0
16
32
48
64
80
96
112
128
144
160
176
192
208
224
240
OSCCAL (X1)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
33
3.2
ATtiny44A
3.2.1
Current Consumption in Active Mode
Figure 3-47. Active Supply Current vs. VCC (Internal RC Oscillator, 8 MHz)
6
125 °C
85 °C
25 °C
-40 °C
5
ICC (mA)
4
3
2
1
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Figure 3-48. Active Supply Current vs. VCC (Internal RC Oscillator, 1 MHz)
1,2
125 °C
85 °C
25 °C
-40 °C
1
ICC (mA)
0,8
0,6
0,4
0,2
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
34
Figure 3-49. Active Supply Current vs. VCC (Internal RC Oscillator, 128 kHz)
0,14
-40 °C
25 °C
85 °C
125 °C
0,12
0,1
ICC (mA)
0,08
0,06
0,04
0,02
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Current Consumption in Idle Mode
Figure 3-50. Idle Supply Current vs. VCC (Internal RC Oscillator, 8 MHz)
2
1,8
125 °C
85 °C
25 °C
-40 °C
1,6
1,4
ICC (mA)
3.2.2
1,2
1
0,8
0,6
0,4
0,2
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
35
Figure 3-51. Idle Supply Current vs. VCC (Internal RC Oscillator, 1 MHz)
0,4
125 °C
85 °C
25 °C
-40 °C
0,35
0,3
ICC (mA)
0,25
0,2
0,15
0,1
0,05
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Figure 3-52. Idle Supply Current vs. VCC (Internal RC Oscillator, 128 kHz)
0,03
125 °C
-40 °C
25 °C
85 °C
0,025
ICC (mA)
0,02
0,015
0,01
0,005
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
36
Current Consumption in Power-down Mode
Figure 3-53. Power-down Supply Current vs. VCC (Watchdog Timer Disabled)
6
125 °C
5
ICC (uA)
4
3
2
85 °C
1
25 °C
-40 °C
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Figure 3-54. Power-down Supply Current vs. VCC (Watchdog Timer Enabled)
12
125 °C
10
8
ICC (uA)
3.2.3
-40 °C
85 °C
25 °C
6
4
2
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
37
Current Consumption of Peripheral Units
Figure 3-55. Programming Current vs. VCC
14000
12000
-40 °C
10000
ICC (uA)
8000
25 °C
6000
85 °C
125 °C
4000
2000
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Figure 3-56. Brownout Detector Current vs. VCC (BOD Level = 1.8V)
35
30
125 °C
85 °C
25 °C
-40 °C
25
ICC (uA)
3.2.4
20
15
10
5
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
38
Figure 3-57. Watchdog Timer Current vs. VCC
0,008
-40 °C
0,007
25 °C
85 °C
125 °C
0,006
ICC (mA)
0,005
0,004
0,003
0,002
0,001
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Pull-up Resistors
Figure 3-58. Pull-up Resistor Current vs. Input Voltage (I/O Pin, VCC = 1.8V)
60
50
40
IOP (uA)
3.2.5
30
20
10
25 °C
-40 °C
85 °C
125 °C
0
0
0,5
1
1,5
2
VOP (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
39
Figure 3-59. Pull-up Resistor Current vs. Input Voltage (I/O Pin, VCC = 2.7V)
80
70
60
IOP (uA)
50
40
30
20
25 °C
-40 °C
85 °C
125 °C
10
0
0
0,5
1
1,5
2
2,5
3
VOP (V)
Figure 3-60. Pull-up Resistor Current vs. Input Voltage (I/O Pin, VCC = 5V)
160
140
120
IOP (uA)
100
80
60
40
25 °C
85 °C
-40 °C
125 °C
20
0
0
1
2
3
4
5
VOP (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
40
Figure 3-61. Reset Pull-up Resistor Current vs. Reset Pin Voltage (VCC = 1.8V)
40
35
30
IRESET (uA)
25
20
15
10
25 °C
-40 °C
85 °C
125 °C
5
0
0
0,5
1
1,5
2
VRESET (V)
Figure 3-62. Reset Pull-up Resistor Current vs. Reset Pin Voltage (VCC = 2.7V)
60
50
IRESET (uA)
40
30
20
10
25 °C
-40 °C
85 °C
125 °C
0
0
0,5
1
1,5
2
2,5
3
VRESET (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
41
Figure 3-63. Reset Pull-up Resistor Current vs. Reset Pin Voltage (VCC = 5V)
120
100
IRESET (uA)
80
60
40
20
25 °C
-40 °C
85 °C
125 °C
0
0
1
2
3
4
5
VRESET (V)
Output Driver Strength
Figure 3-64. VOL: Output Voltage vs. Sink Current (I/O Pin, VCC = 1.8V)
0,5
125 °C
0,4
85 °C
0,3
25 °C
VOL (V)
3.2.6
-40 °C
0,2
0,1
0
0
1
2
3
4
5
IOL (mA)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
42
Figure 3-65. VOL: Output Voltage vs. Sink Current (I/O Pin, VCC = 3V)
0,5
125 °C
0,4
85 °C
25 °C
VOL (V)
0,3
-40 °C
0,2
0,1
0
0
2
4
6
8
10
IOL (mA)
Figure 3-66. VOL: Output Voltage vs. Sink Current (I/O Pin, VCC = 5V)
0,7
125 °C
0,6
85 °C
0,5
VOL (V)
25 °C
0,4
-40 °C
0,3
0,2
0,1
0
0
5
10
15
20
IOL (mA)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
43
Figure 3-67. VOH: Output Voltage vs. Source Current (I/O Pin, VCC = 1.8V)
1,8
1,7
VOH (V)
1,6
1,5
-40 °C
1,4
25 °C
85 °C
125 °C
1,3
0
1
2
3
4
5
IOH (mA)
Figure 3-68. VOH: Output Voltage vs. Source Current (I/O Pin, VCC = 3V)
3
2,9
VOH (V)
2,8
2,7
-40 °C
25 °C
2,6
85 °C
125 °C
2,5
0
2
4
6
8
10
IOH (mA)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
44
Figure 3-69. VOH: Output Voltage vs. Source Current (I/O Pin, VCC = 5V)
5
4,9
VOH (V)
4,8
4,7
4,6
-40 °C
4,5
25 °C
4,4
85 °C
125 °C
4,3
0
5
10
15
20
IOH (mA)
Figure 3-70. VOL: Output Voltage vs. Sink Current (Reset Pin as I/O, VCC = 3V)
2
125 °C
1,6
85 °C
0,8
25 °C
VOL (V)
1,2
-40 °C
0,4
0
0
0,5
1
1,5
2
2,5
3
IOL (mA)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
45
Figure 3-71. VOL: Output Voltage vs. Sink Current (Reset Pin as I/O, VCC = 5V)
1,2
125 °C
1
85 °C
VOL (V)
0,8
25 °C
0,6
-40 °C
0,4
0,2
0
0
1
2
3
4
5
IOL (mA)
Figure 3-72. VOH: Output Voltage vs. Source Current (Reset Pin as I/O, VCC = 3V)
3
2,5
VOH (V)
2
1,5
-40 °C
25 °C
85 °C
125 °C
1
0,5
0
0
0,4
0,8
1,2
1,6
IOH (mA)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
46
Figure 3-73. VOH: Output Voltage vs. Source Current (Reset Pin as I/O, VCC = 5V)
5
4
3
VOH (V)
-40 °C
25 °C
85 °C
125 °C
2
1
0
0
0,4
0,8
1,2
1,6
IOH (mA)
Input Threshold and Hysteresis (for I/O Ports)
Figure 3-74. VIH: Input Threshold Voltage vs. VCC (IO Pin, Read as ‘1’)
3,5
125 °C
85 °C
25 °C
-40 °C
3
2,5
Threshold (V)
3.2.7
2
1,5
1
0,5
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
47
Figure 3-75. VIL: Input Threshold Voltage vs. VCC (I/O Pin, Read as ‘0’)
2,5
125 °C
85 °C
25 °C
-40 °C
Threshold (V)
2
1,5
1
0,5
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
4
4,5
5
5,5
VCC (V)
Figure 3-76. VIH-VIL: Input Hysteresis vs. VCC (I/O Pin)
0,8
0,7
Input Hysteresis (V)
0,6
-40 °C
0,5
25 °C
0,4
85 °C
0,3
125 °C
0,2
0,1
0
1,5
2
2,5
3
3,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
48
Figure 3-77. VIH: Input Threshold Voltage vs. VCC (Reset Pin as I/O, Read as ‘1’)
3
125 °C
85 °C
25 °C
-40 °C
2,5
Threshold (V)
2
1,5
1
0,5
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Figure 3-78. VIL: Input Threshold Voltage vs. VCC (Reset Pin as I/O, Read as ‘0’)
2,5
125 °C
85 °C
25 °C
-40 °C
Threshold (V)
2
1,5
1
0,5
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
49
Figure 3-79. VIH-VIL: Input Hysteresis vs. VCC (Reset Pin as I/O)
1
0,8
Input Hysteresis (V)
-40 °C
25 °C
0,6
85 °C
125 °C
0,4
0,2
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
BOD, Bandgap and Reset
Figure 3-80. BOD Threshold vs. Temperature (BODLEVEL = 4.3V)
4,36
4,34
4,32
Threshold (V)
3.2.8
4,3
Rising VCC
4,28
4,26
4,24
4,22
Falling VCC
4,2
-40
-20
0
20
40
60
80
100
120
140
Temperature (C)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
50
Figure 3-81. BOD Threshold vs. Temperature (BODLEVEL = 2.7V)
2,78
2,76
Threshold (V)
2,74
Rising VCC
2,72
2,7
2,68
2,66
Falling VCC
2,64
-40
-20
0
20
40
60
80
100
120
140
Temperature (C)
Figure 3-82. BOD Threshold vs. Temperature (BODLEVEL =1.8V)
1,84
1,83
Threshold (V)
1,82
1,81
Rising VCC
1,8
1,79
1,78
Falling VCC
1,77
1,76
-40
-20
0
20
40
60
80
100
120
140
Temperature (C)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
51
Figure 3-83. Bandgap Voltage vs. Temperature (VCC =5V)
1,12
Bandgap Voltage (V)
1,11
1,1
1,09
1,08
1,07
1,06
-40
-20
0
20
40
60
80
100
120
140
Temperature
Figure 3-84. VIH: Input Threshold Voltage vs. VCC (Reset Pin, Read as ‘1’)
2,5
-40 °C
25 °C
85 °C
125 °C
Threshold (V)
2
1,5
1
0,5
0
1
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
52
Figure 3-85. VIL: Input Threshold Voltage vs. VCC (Reset Pin, Read as ‘0’)
2,5
125 °C
85 °C
25 °C
-40 °C
Threshold (V)
2
1,5
1
0,5
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Figure 3-86. VIH-VIL: Input Hysteresis vs. VCC (Reset Pin)
1
0,9
0,8
Input Hysteresis (V)
0,7
0,6
-40 °C
0,5
25 °C
0,4
0,3
85 °C
0,2
125 °C
0,1
0
1
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
53
Figure 3-87. Minimum Reset Pulse Width vs. VCC
2000
Pulsewidth (ns)
1500
1000
500
125 °C
85 °C
25 °C
-40 °C
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Analog Comparator Offset
Figure 3-88. Analog Comparator Offset (VCC = 5V)
0,004
0,002
0
0
Offset (V)
3.2.9
0,5
1
1,5
2
2,5
3
3,5
4
4,5
5
-0,002
-0,004
-40 °C
25 °C
85 °C
125 °C
-0,006
-0,008
VIN (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
54
3.2.10 Internal Oscillator Speed
Figure 3-89. Watchdog Oscillator Frequency vs. VCC
0,12
0,118
-40 °C
Frequency (MHz)
0,116
25 °C
0,114
0,112
0,11
85 °C
0,108
0,106
0,104
125 °C
0,102
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Figure 3-90. Watchdog Oscillator Frequency vs. Temperature
0,12
0,118
Frequency (MHz)
0,116
0,114
0,112
0,11
0,108
1.8 V
0,106
3.0 V
0,104
5.0 V
0,102
-40
-20
0
20
40
60
80
100
120
140
Temperature
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
55
Figure 3-91. Calibrated 8 MHz RC Oscillator Frequency vs. Temperature
8,2
5.0 V
3.0 V
8,1
1.8 V
Frequency (MHz)
8
7,9
7,8
7,7
7,6
7,5
-40
-20
0
20
40
60
80
100
120
140
Temperature
Figure 3-92. Calibrated 8 MHz RC Oscillator Frequency vs. OSCCAL Value
16
125 °C
85 °C
25 °C
-40 °C
14
Frequency (MHz)
12
10
8
6
4
2
0
0
16
32
48
64
80
96
112
128
144
160
176
192
208
224
240
OSCCAL (X1)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
56
3.3
ATtiny84A
3.3.1
Current Consumption in Active Mode
Figure 3-93. Active Supply Current vs. Frequency (1 - 16 MHz, PRR = 0xFF)
12
10
8
5.5 V
ICC (mA)
5.0 V
6
4.5 V
4.0 V
4
3.3 V
2
2.7 V
1.8 V
0
0
2
4
6
8
10
12
14
16
18
20
Frequency (MHz)
Figure 3-94. Active Supply Current vs. VCC (Internal RC Oscillator, 8 MHz)
5
125 °C
85 °C
25 °C
-40 °C
4,5
4
3,5
ICC (mA)
3
2,5
2
1,5
1
0,5
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
57
Figure 3-95. Active Supply Current vs. VCC (Internal RC Oscillator, 1 MHz)
1,4
1,2
125 °C
85 °C
25 °C
-40 °C
1
ICC (mA)
0,8
0,6
0,4
0,2
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Figure 3-96. Active Supply Current vs. VCC (Internal RC Oscillator, 128 kHz)
0,14
0,12
125 °C
25 °C
-40 °C
85 °C
0,1
ICC (mA)
0,08
0,06
0,04
0,02
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
58
Current Consumption in Idle Mode
Figure 3-97. Idle Supply Current vs. Frequency (1 - 16MHz, PRR = 0xFF)
4
3,5
3
ICC (mA)
2,5
2
5.5 V
1,5
4.5 V
5.0 V
4.0 V
1
3.3 V
0,5
2.7 V
1.8 V
0
0
2
4
6
8
10
12
14
16
18
20
Frequency (MHz)
Figure 3-98. Idle Supply Current vs. VCC (Internal RC Oscillator, 8 MHz)
2
1,8
1,6
1,4
125 °C
85 °C
25 °C
-40 °C
1,2
ICC (mA)
3.3.2
1
0,8
0,6
0,4
0,2
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
59
Figure 3-99. Idle Supply Current vs. VCC (Internal RC Oscillator, 1 MHz)
0,4
0,35
125 °C
85 °C
25 °C
-40 °C
0,3
ICC (mA)
0,25
0,2
0,15
0,1
0,05
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Figure 3-100.Idle Supply Current vs. VCC (Internal RC Oscillator, 128 kHz)
0,03
125 °C
0,025
-40 °C
85 °C
25 °C
ICC (mA)
0,02
0,015
0,01
0,005
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
60
Current Consumption in Power-down Mode
Figure 3-101.Power-down Supply Current vs. VCC (Watchdog Timer Disabled)
4
125 °C
3,5
3
ICC (uA)
2,5
2
1,5
85 °C
1
0,5
25 °C
-40 °C
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Figure 3-102.Power-down Supply Current vs. VCC (Watchdog Timer Enabled)
14
125 °C
12
10
8
-40 °C
85 °C
25 °C
ICC (uA)
3.3.3
6
4
2
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
61
3.3.4
Current Consumption in Reset
Figure 3-103.Reset Supply Current vs. VCC (1 - 16 MHz, Excluding Current through Reset Pull-up)
3
2,5
ICC (mA)
2
5.5 V
1,5
5.0 V
4.5 V
1
4.0 V
3.3 V
0,5
2.7 V
1.8 V
0
0
2
4
6
8
10
12
14
16
18
20
Frequency (MHz)
Current Consumption of Peripheral Units
Figure 3-104.Programming Current vs. VCC
7000
6000
-40 °C
5000
25 °C
4000
ICC (uA)
3.3.5
85 °C
125 °C
3000
2000
1000
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
62
Figure 3-105.Brownout Detector Current vs. VCC (BOD Level = 1.8V)
45
40
35
ICC (uA)
30
125 °C
85 °C
25 °C
-40 °C
25
20
15
10
5
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Pull-up Resistors
Figure 3-106.Pull-up Resistor Current vs. Input Voltage (I/O Pin, VCC = 1.8V)
60
50
40
IOP (uA)
3.3.6
30
20
10
25 °C
-40 °C
125 °C
85 °C
0
0
0,2
0,4
0,6
0,8
1
1,2
1,4
1,6
1,8
2
VOP (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
63
Figure 3-107.Pull-up Resistor Current vs. Input Voltage (I/O Pin, VCC = 2.7V)
80
70
60
IOP (uA)
50
40
30
20
25 °C
-40 °C
125 °C
85 °C
10
0
0
0,5
1
1,5
2
2,5
3
VOP (V)
Figure 3-108.Pull-up Resistor Current vs. Input Voltage (I/O Pin, VCC = 5V)
160
140
120
IOP (uA)
100
80
60
40
25 °C
-40 °C
125 °C
85 °C
20
0
0
1
2
3
4
5
6
VOP (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
64
Figure 3-109.Reset Pull-up Resistor Current vs. Reset Pin Voltage (VCC = 1.8V)
40
35
30
IRESET (uA)
25
20
15
10
5
-40 °C
25 °C
85 °C
125 °C
0
0
0,2
0,4
0,6
0,8
1
1,2
1,4
1,6
1,8
2
VRESET (V)
Figure 3-110.Reset Pull-up Resistor Current vs. Reset Pin Voltage (VCC = 2.7V)
60
50
IRESET (uA)
40
30
20
10
-40 °C
25 °C
85 °C
125 °C
0
0
0,5
1
1,5
2
2,5
3
VRESET (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
65
Figure 3-111.Reset Pull-up Resistor Current vs. Reset Pin Voltage (VCC = 5V)
120
100
IRESET (uA)
80
60
40
20
-40 °C
25 °C
85 °C
125 °C
0
0
0,5
1
1,5
2
2,5
3
3,5
4
4,5
5
VRESET (V)
Output Driver Strength
Figure 3-112.VOL: Output Voltage vs. Sink Current (I/O Pin, VCC = 3V)
1,2
125 °C
1
85 °C
0,8
25 °C
VOL (V)
3.3.7
-40 °C
0,6
0,4
0,2
0
0
2
4
6
8
10
12
14
16
18
20
IOL (mA)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
66
Figure 3-113.VOL: Output Voltage vs. Sink Current (I/O Pin, VCC = 5V)
0,7
125 °C
0,6
85 °C
0,5
25 °C
-40 °C
VOL (V)
0,4
0,3
0,2
0,1
0
0
2
4
6
8
10
12
14
16
18
20
IOL (mA)
Figure 3-114.VOH: Output Voltage vs. Source Current (I/O Pin, VCC = 3V)
3,2
3
2,8
VOH (V)
2,6
2,4
-40 °C
25 °C
2,2
85 °C
2
125 °C
1,8
0
2
4
6
8
10
12
14
16
18
20
IOH (mA)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
67
Figure 3-115.VOH: Output Voltage vs. Source Current (I/O Pin, VCC = 5V)
5,2
5
VOH (V)
4,8
4,6
-40 °C
25 °C
4,4
85 °C
125 °C
4,2
0
2
4
6
8
10
12
14
16
18
20
IOH (mA)
Figure 3-116.VOL: Output Voltage vs. Sink Current (Reset Pin as I/O, VCC = 3V)
2
1,8
125 °C
1,6
1,4
VOL (V)
1,2
85 °C
1
25 °C
0,8
-40 °C
0,6
0,4
0,2
0
0
0,5
1
1,5
2
2,5
3
IOL (mA)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
68
Figure 3-117.VOL: Output Voltage vs. Sink Current (Reset Pin as I/O, VCC = 5V)
2
125 °C
85 °C
1,8
1,6
25 °C
1,4
1,2
VOL (V)
-40 °C
1
0,8
0,6
0,4
0,2
0
0
1
2
3
4
5
6
7
8
IOL (mA)
Figure 3-118.VOH: Output Voltage vs. Source Current (Reset Pin as I/O, VCC = 3V)
3
2,5
VOH (V)
2
1,5
-40 °C
25 °C
1
85 °C
125 °C
0,5
0
0
0,2
0,4
0,6
0,8
1
1,2
1,4
1,6
1,8
2
IOH (mA)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
69
Figure 3-119.VOH: Output Voltage vs. Source Current (Reset Pin as I/O, VCC = 5V)
5
4,5
4
3,5
VOH (V)
3
-40 °C
25 °C
85 °C
125 °C
2,5
2
1,5
1
0,5
0
0
0,2
0,4
0,6
0,8
1
1,2
1,4
1,6
1,8
2
IOH (mA)
Input Threshold and Hysteresis (for I/O Ports)
Figure 3-120.VIH: Input Threshold Voltage vs. VCC (I/O Pin, Read as ‘1’)
3,5
125 °C
85 °C
25 °C
-40 °C
3
2,5
Threshold (V)
3.3.8
2
1,5
1
0,5
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
70
Figure 3-121.VIL: Input Threshold Voltage vs. VCC (I/O Pin, Read as ‘0’)
3
125 °C
85 °C
25 °C
-40 °C
2,5
Threshold (V)
2
1,5
1
0,5
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Figure 3-122.VIH-VIL: Input Hysteresis vs. VCC (I/O Pin)
0,6
125 °C
85 °C
25 °C
-40 °C
0,5
Input Hysteresis (mV)
0,4
0,3
0,2
0,1
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
71
Figure 3-123.VIH: Input Threshold Voltage vs. VCC (Reset Pin as I/O, Read as ‘1’)
3
125 °C
85 °C
25 °C
-40 °C
2,5
Threshold (V)
2
1,5
1
0,5
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Figure 3-124.VIL: Input Threshold Voltage vs. VCC (Reset Pin as I/O, Read as ‘0’)
2,5
125 °C
85 °C
25 °C
-40 °C
Threshold (V)
2
1,5
1
0,5
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
72
Figure 3-125.VIH-VIL: Input Hysteresis vs. VCC (Reset Pin as I/O)
1
0,9
0,8
125 °C
25 °C
85 °C
-40 °C
Input Hysteresis (V)
0,7
0,6
0,5
0,4
0,3
0,2
0,1
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
BOD, Bandgap and Reset
Figure 3-126.BOD Threshold vs. Temperature (BODLEVEL = 4.3V)
4,42
RISING VCC
4,4
4,38
4,36
Threshold (V)
3.3.9
4,34
FALLING VCC
4,32
4,3
4,28
4,26
4,24
-40
-20
0
20
40
60
80
100
120
140
Temperature (C)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
73
Figure 3-127.BOD Threshold vs. Temperature (BODLEVEL = 2.7V)
2,82
2,8
RISING VCC
2,78
Threshold (V)
2,76
2,74
FALLING VCC
2,72
2,7
2,68
2,66
-40
-20
0
20
40
60
80
100
120
140
80
100
120
140
Temperature (C)
Figure 3-128.Bandgap Voltage vs. Temperature (VCC =5V)
1,2
1,18
1,16
Bandgap Voltage (V)
1,14
1,12
1,1
1,08
1,06
1,04
1,02
1
-40
-20
0
20
40
60
Temperature
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
74
Figure 3-129.VIH: Input Threshold Voltage vs. VCC (Reset Pin, Read as ‘1’)
2,5
-40 °C
25 °C
85 °C
125 °C
Threshold (V)
2
1,5
1
0,5
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Figure 3-130.VIL: Input Threshold Voltage vs. VCC (Reset Pin, Read as ‘0’)
2,5
125 °C
85 °C
25 °C
-40 °C
Threshold (V)
2
1,5
1
0,5
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
75
Figure 3-131.VIH-VIL: Input Hysteresis vs. VCC (Reset Pin)
1
0,9
0,8
Input Hysteresis (V)
0,7
0,6
-40 °C
0,5
25 °C
0,4
0,3
85 °C
0,2
125 °C
0,1
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
Figure 3-132.Minimum Reset Pulse Width vs. VCC
2000
1800
1600
Pulsewidth (ns)
1400
1200
1000
800
600
400
125 °C
85 °C
25 °C
-40 °C
200
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
76
3.3.10 Analog Comparator Offset
Figure 3-133.Analog Comparator Offset (VCC = 5V)
0,004
0,002
0
0
0,5
1
1,5
2
2,5
3
3,5
4
4,5
5
Offset (V)
-0,002
-0,004
-0,006
-40
25
-0,008
85
-0,01
125
-0,012
Vin (V)
3.3.11 Internal Oscillator Speed
Figure 3-134.Watchdog Oscillator Frequency vs. VCC
118
116
-40 °C
114
25 °C
FRC (kHz)
112
110
85 °C
108
125 °C
106
104
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
77
Figure 3-135.Watchdog Oscillator Frequency vs. Temperature
118
116
114
FRC (kHz)
1.8 V
112
110
3.0 V
108
5.5 V
106
104
-40
-20
0
20
40
60
80
100
120
140
Temperature
Figure 3-136.Calibrated 8 MHz RC Oscillator Frequency vs. VCC
8,3
85 °C
125 °C
8,2
25 °C
FRC (MHz)
8,1
8
-40 °C
7,9
7,8
7,7
1,5
2
2,5
3
3,5
4
4,5
5
5,5
VCC (V)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
78
Figure 3-137.Calibrated 8 MHz RC Oscillator Frequency vs. Temperature
8,2
8,15
5.0 V
8,1
3.0 V
8,05
FRC (MHz)
8
1.8 V
7,95
7,9
7,85
7,8
7,75
7,7
-40
-20
0
20
40
60
80
100
120
140
Temperature
Figure 3-138.Calibrated 8 MHz RC Oscillator Frequency vs. OSCCAL Value
16
-40 °C
25 °C
85 °C
125 °C
14
12
FRC (MHz)
10
8
6
4
2
0
0
16
32
48
64
80
96
112
128
144
160
176
192
208
224
240
OSCCAL (X1)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
79
4.
Ordering Information
4.1
ATtiny24A
Speed (MHz) (1)
Supply Voltage (V)
Temperature Range
Package (2)
Ordering Code (3)
ATtiny24A-SSF
14S1
ATtiny24A-SSFR
20
1.8 – 5.5V
Industrial
(-40C to +125C)
ATtiny24A-MF
20M1
ATtiny24A-MFR
ATtiny24A-MM8
20M2
ATtiny24A-MM8R
Notes: 1. For speed vs. supply voltage, see section 2.3 “Speed” on page 5.
2. All packages are Pb-free, halide-free and fully green and they comply with the European directive for Restriction of
Hazardous Substances (RoHS).
3. Code indicators:

F: matte tin

R: tape & reel
Package Type
14S1
14-lead, 0.150" Wide Body, Plastic Gull Wing Small Outline Package (SOIC)
20M1
20-pad, 4 x 4 x 0.8 mm Body, Quad Flat No Lead / Micro Lead Frame Package (QFN/MLF)
20M2
20-pad, 3 x 3 x 0.85 mm Body, Very Thin Quad Flat No Lead Package (VQFN)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
80
4.2
ATtiny44A
Speed (MHz) (1)
Supply Voltage (V)
Temperature Range
Package (2)
Ordering Code (3)
ATtiny44A-SSF
14S1
20
1.8 – 5.5V
ATtiny44A-SSFR
Industrial
(-40C to +125C)
ATtiny44A-MF
20M1
ATtiny44A-MFR
Notes: 1. For speed vs. supply voltage, see section 2.3 “Speed” on page 5.
2. All packages are Pb-free, halide-free and fully green and they comply with the European directive for Restriction of
Hazardous Substances (RoHS).
3. Code indicators:

F: matte tin

R: tape & reel
Package Type
14S1
14-lead, 0.150" Wide Body, Plastic Gull Wing Small Outline Package (SOIC)
20M1
20-pad, 4 x 4 x 0.8 mm Body, Quad Flat No Lead / Micro Lead Frame Package (QFN/MLF)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
81
4.3
ATtiny84A
Speed (MHz) (1)
Supply Voltage (V)
Temperature Range
Package (2)
Ordering Code (3)
ATtiny84A-SSF
14S1
16
1.8 – 5.5V
ATtiny84A-SSFR
Industrial
(-40C to +125C)
ATtiny84A-MF
20M1
ATtiny84A-MFR
Notes: 1. For speed vs. supply voltage, see section 2.3 “Speed” on page 5.
2. All packages are Pb-free, halide-free and fully green and they comply with the European directive for Restriction of
Hazardous Substances (RoHS).
3. Code indicators:

F: matte tin

R: tape & reel
Package Type
14S1
14-lead, 0.150" Wide Body, Plastic Gull Wing Small Outline Package (SOIC)
20M1
20-pad, 4 x 4 x 0.8 mm Body, Quad Flat No Lead / Micro Lead Frame Package (QFN/MLF)
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
82
5.
Revision History
Revision No.
History
8183A: Appendix B–AVR–12/10
Initial revision
8183D: Appendix B–AVR–08/11
Added tape&reel order codes
8183E: Appendix B–AVR–01/12
Added ATtiny84A
8183F: Appendix B–AVR–06/12
Updated order codes for ATtiny24A
8183G: Appendix B–AVR–10/12
Relaxed ATtiny84A speed limits (Section 2.3 on page 5, Table 2-8 on page 10, Section
2.8 on page 10, Figure 3-93 on page 57, Figure 3-97 on page 59, Figure 3-103 on
page 62, and Section 4.3 on page 82).
Updated document template.
8183H: Appendix B-AVR-10/13
Updated ordering codes for ATtiny84A: -MF and -MFR options added.
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
83
ATtiny24A/44A/84A [DATASHEET APPENDIX B]
8183H–AVR–10/2013
84
Atmel Corporation
1600 Technology Drive
Atmel Asia Limited
Unit 01-5 & 16, 19F
Atmel Munich GmbH
Business Campus
Atmel Japan G.K.
16F Shin-Osaki Kangyo Bldg
San Jose, CA 95110
BEA Tower, Millennium City 5
Parkring 4
1-6-4 Osaki, Shinagawa-ku
USA
418 Kwun Tong Roa
D-85748 Garching b. Munich
Tokyo 141-0032
Tel: (+1) (408) 441-0311
Kwun Tong, Kowloon
GERMANY
JAPAN
Fax: (+1) (408) 487-2600
HONG KONG
Tel: (+49) 89-31970-0
Tel: (+81) (3) 6417-0300
www.atmel.com
Tel: (+852) 2245-6100
Fax: (+49) 89-3194621
Fax: (+81) (3) 6417-0370
Fax: (+852) 2722-1369
© 2013 Atmel Corporation. All rights reserved. / Rev.: 8183H–AVR–10/2013
Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, AVR®, tinyAVR® and others are registered trademarks or trademarks of Atmel
Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this
document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES
NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF
INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time
without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in,
automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.