SIDACtor ® Protection Thyristors LCAS Protection Asymmetrical Multiport Series - MS-013 Description Asymmetrical Multiport Series are SIDACtor® devices designed to protect LCAS (Line Circuit Access Switch) devices from damaging overvoltage transients. The series provides a specialized asymmetrical dual port overvoltage protection solution that enables equipment to comply with various global requlatory standards. Features and Benefits t Low voltage overshoot t Low on-state voltage t Does not degrade with use Agency Approvals Agency t Fails short circuit when surged in excess of ratings Agency File Number E133083 Pinout Designation t Replaces four discrete devices t Two-port protection t LCAS specific tip and ring thresholds Applicable Global Standards 1 6 t TIA-968-A t GR 1089 Intra-building 2 5 t TIA-968-B t IEC 61000-4-5 4 t ITU K.20/21 Enhanced Level* t YD/T 1082 3 t ITU K.20/21 Basic Level t YD/T 950 Schematic Symbol t YD/T 993 t GR 1089 Inter-building* (T1) 1 6 (T2) (G1) 2 5 (G2) (R1) 3 4 (R2) *A-rated parts require series resistance Electrical Characteristics VDRM @IDRM VS VDRM @IDRM = 5μA @100V/μs = 5μA Part Number Part Marking A1220UA4Lxx A1225UA4Lxx A1220UC4Lxx A1225UC4Lxx A1220UA4 A1250UA4 A1220UC4 A1250UC4 V V Pins 2-3, 5-6 100 100 100 100 130 130 130 130 V VS @100V/μs VT@IT = 2.2 Amps V V Pins 1-2, 4-5 180 230 180 230 220 290 220 290 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional. - All electrical characteristics shown are defined from Tip to Ground (pin 1 to pin 2 and pin 6 to pin 5) and Ring to Ground (pin 3 to pin 2 and pin 4 to pin 5). - XX = Part Number Suffix: ‘TP’ (Tube Pack) or ‘RP’ (Reel Pack). © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 130 Revised: February 22, 2011 IS mA IT A IH mA 800 800 800 800 2.2 2.2 2.2 2.2 120 120 120 120 Pins 1-2, 2-3, 4-5, 5-6 4 4 4 4 SIDACtor ® Protection Thyristors LCAS Protection Capacitance Values pF Pin 1-2 / 4-5 Ring-Ground Part Number A1220UA4Lxx A1225UA4Lxx A1220UC4Lxx A1225UC4Lxx pF Pin 3-2 / 6-5 Tip-Ground pF Pin 1-3 (4-6) Tip-Ring MIN MAX MIN MAX MIN MAX 15 15 35 35 25 25 50 50 30 30 60 60 50 50 90 90 5 5 20 20 20 20 35 35 Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. Surge Ratings Series IPP ITSM 50/60 Hz di/dt A min A min A/μs max 0.2x310 0.5x700 2 2x10 2x10 2 8x20 1.2x50 2 10x160 10x160 2 10x560 1 10x560 2 5x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5x310 1 10x700 2 A min A min A min A min A min A min A min A min 1 1 1 1 A 20 150 150 90 50 75 75 45 75 20 500 C 50 500 400 200 150 200 175 100 200 30 500 Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPPSBUJOHTBQQMJDBCMFPWFSUFNQFSBUVSFSBOHFPG$UP$ - The device must initially be in thermal equilibrium with -40°C < TJ <¡$ 1 Current waveform in μs 2 Voltage waveform in μs Thermal Considerations Package Symbol Modified MS-013 6 5 4 2 Value Unit TJ Operating Junction Temperature Range UP °C TS Storage Temperature Range UP °C 60 °C/W R0JA 3 Parameter Thermal Resistance: Junction to Ambient V-I Characteristics tr x td Pulse Waveform IPP – Peak Pulse Current – %IPP +I IT IS IH IDRM -V +V VT VDRM VS Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 -I © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 131 Revised: February 22, 2011 tr td t – Time (μs) SIDACtor ® Protection Thyristors LCAS Protection Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature 2.0 IH 10 8 6 25 °C 4 2 0 -4 1.8 IH (TC = 25ºC) 12 1.6 1.4 25°C 1.2 1.0 Ratio of Percent of VS Change – % 14 0.8 0.6 -6 0.4 -40 -8 -40 -20 0 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC 20 40 60 80 100 120 140 160 Junction Temperature (TJ) – °C Soldering Parameters - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Pb-Free assembly (see Fig. 1) ¡$ ¡$ 60-180 secs. Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) ¡$ - Temperature (tL) 60-150 secs. Peak Temp (TP) ¡$ Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed ¡$ Figure 1 TL TS(max) tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Physical Specifications High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ¡$PS¡$ 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Temp Cycling ¡$UP¡$NJOEXFMMVQUP cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC¡$ 3)VQUPIST&*" JEDEC, JESD22-A-101 High Temp Storage ¡$IST.*-45%.FUIPE JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock ¡$UP¡$NJOEXFMMTFDUSBOTGFS 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Lead Material Copper Alloy Terminal Finish 100% Matte-Tin Plated Body Material UL recognized epoxy meeting flammability classification 94V-0 Part Numbering A xxxx U x 4 L xx TYPE A: Asymmetrical SIDACtor ¡$3)BUNVQUPIST&*" JEDEC, JESD22-A-102 Resistance to Solder Heat ¡$TFDT.*-45%.FUIPE Moisture Sensitivity Level 3)¡$ISTSFnPXDZDMFT ¡$1FBL +&%&$+45%-FWFM © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Critical Zone TL to TP Ramp-up Environmental Specifications Autoclave (Pressure Cooker Test) tP TP Temperature Reflow Condition MEDIAN VOLTAGE PACKAGE TYPE IPP RATING 132 Revised: February 22, 2011 PACKING OPTIONS RP: Reel Pack TP: Tube Pack RoHS COMPLIANT CONSTRUCTION VARIABLE SIDACtor ® Protection Thyristors LCAS Protection Part Marking Packing Options Package Type Part Marking Code XXXXXXXX (Refer to Electrical Characteristics Table) Date Code XXXXX U Description Quantity Added Suffix Industry Standard Modified MS-013 6-pin Tape and Reel Pack 1500 RP EIA-481-D TP N/A 500 Modified MS-013 6-pin (50 per Tube Pack tube) Dimensions — MS-013 Dimensions 0.065 (1.65) Pad Outline C A B C D E F G H J K BSC* 0.460 (11.68) 0.138 (3.50) Dimension are in inches (and millimeters). 0.059 (1.50) E D 7º TYP J 7º TYP A G Burr Side H 96º A Mold Split Line 4º A 7º TYP BSC* F MIN Length of Flat 7º TYP K Detail A B Inches Max Min Max 0.360 0.352 0.400 0.043 0.047 0.293 0.289 0.089 0.041 0.020 0.133 0.364 0.356 0.412 0.045 0.055 0.297 0.293 0.093 0.049 9.14 8.94 10.16 1.09 1.19 7.44 7.34 2.26 1.04 0.51 3.38 9.25 9.04 10.46 1.13 1.40 7.54 7.44 2.36 1.24 0.143 * BSC = Basic Spacing between Centers Tape and Reel Specification — MS-013 .157 (4.0) .630 (16.0) .472 (12.0) 12.99 (330) .512 (13.0) Arbor Hole Dia. Dimensions are in inches (and millimeters) 0.700 (17.8) Direction of Feed Tube Pack Specification — MS-013 Message Location .045 (1.14) .310 (7.87) 90˚ .165 (4.19) 6 Interior of the Tube .225 (5.72) .150 (3.81) .525 (13.34) © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. .020 ± .005 WALL TYP. (0.51 ± 0.13) .108 (2.74) .005 A .110 (2.79) A Dimensions are in inches (and millimeters) 133 Revised: February 22, 2011 Millimeters Min 20.000 ± .030 (508.00 ± 0.76) 3.63