NCV4299 D

NCV4299
150 mA Low-Dropout
Voltage Regulator
The NCV4299 is a family of precision micropower voltage regulators
with an output current capability of 150 mA. It is available in 5.0 V or
3.3 V output voltage, and is housed in an 8−lead SOIC and in a 14−lead
SOIC (fused) package.
The output voltage is accurate within "2% with a maximum
dropout voltage of 0.5 V at 100 mA. Low Quiescent current is a
feature drawing only 90 mA with a 1 mA load. This part is ideal for any
and all battery operated microprocessor equipment.
The device features microprocessor interfaces including an
adjustable reset output and adjustable system monitor to provide
shutdown early warning. An inhibit function is available on the
14−lead part. With inhibit active, the regulator turns off and the device
consumes less than 1.0 mA of quiescent current.
The part can withstand load dump transients making it suitable for
use in automotive environments.
http://onsemi.com
MARKING
DIAGRAMS
8
SO−8
D SUFFIX
CASE 751
8
1
4299
ALYW
G
1
14
NCV4299G
AWLYWW
Features
• 5.0 V, 3.3 V "2%, 150 mA
• Extremely Low Current Consumption
14
90 mA (Typ) in the ON Mode
t1.0 mA in the Off Mode
Early Warning
Reset Output Low Down to VQ = 1.0 V
Adjustable Reset Threshold
Wide Temperature Range
Fault Protection
♦ 60 V Peak Transient Voltage
♦ −40 V Reverse Voltage
♦ Short Circuit
♦ Thermal Overload
Internally Fused Leads in the SO−14 Package
Inhibit Function with mA Current Consumption in the Off Mode
NCV Prefix for Automotive and Other Applications Requiring Site
and Change Control
These are Pb−Free Devices
♦
•
•
•
•
•
•
•
•
•
1
SO−14
1
D SUFFIX
CASE 751A 14
♦
V4299xxG
AWLYWW
1
xx
A
L, WL
Y
W, WW
G or G
= 33 (3.3 V Version)
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
PIN CONNECTIONS
I
1
8
SI
RADJ
SO
RO
D
RADJ
D
GND
GND
GND
INH
RO
Q
GND
1
14
SI
I
GND
GND
GND
Q
SO
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 21 of this data sheet.
© Semiconductor Components Industries, LLC, 2009
March, 2009 − Rev. 21
1
Publication Order Number:
NCV4299/D
NCV4299
Q
I
Bandgap
Reference
Current Limit and
Saturation Sense
+
RSO
RRO
SO
1.36 V
+
−
SI
8 mA
+
+
-
RADJ
RO
+
1.85 V
D
GND
Figure 1. SO−8 Simplified Block Diagram
PIN FUNCTION DESCRIPTION − SO−8 PACKAGE
Pin
Symbol
Description
1
I
2
SI
3
RADJ
4
D
5
GND
6
RO
Reset Output. NPN collector output with internal 20 kW pullup to Q. Notifies user of out of regulation
condition. Leave open if not used.
7
SO
Sense Output. NPN collector output with internal 20 kW pullup to Q. Can be used to provide early warning
of an impending reset condition. Leave open if not used.
8
Q
Input. Battery Supply Input Voltage. Bypass directly to GND with ceramic capacitor.
Sense Input. Can provide an early warning signal of an impending reset condition when used with SO.
Connect to Q if not used.
Reset Adjust. Use resistor divider to Q to adjust reset threshold lower. Connect to GND if not used.
Reset Delay. Connect external capacitor to ground to set delay time.
Ground.
5.0 V, 3.3 V, "2%, 150 mA output. Use 22 mF, ESR t 5.0 W to ground.
http://onsemi.com
2
NCV4299
Q
I
Bandgap
Reference
Current Limit and
Saturation Sense
+
RSO
RRO
INH
SO
1.36 V
SI
+
−
8 mA
+
+
-
RADJ
RO
+
1.85 V
D
GND
Figure 2. SO−14 Simplified Block Diagram
PIN FUNCTION DESCRIPTION − SO−14 PACKAGE
Pin
Symbol
Description
1
RADJ
2
D
3
GND
Ground.
4
GND
Ground.
5
GND
Ground.
6
INH
Inhibit. Connect to I if not needed. A high turns the regulator on. Use a low pass filter if transients with slew
rate in excess of 10 V/ms may be present on this pin during operation. See Figure 40 for details.
7
RO
Reset Output. NPN collector output with internal 20 kW pullup to Q. Notifies user of out of regulation
condition.
8
SO
Sense Output. NPN collector output with internal 20 kW pullup to Q. Can be used to provide early warning
of an impending reset condition.
9
Q
10
GND
Ground.
11
GND
Ground.
12
GND
Ground.
13
I
14
SI
Reset Adjust. Use resistor divider to Q to adjust reset threshold lower. Connect to GND if not used.
Reset Delay. Connect external capacitor to ground to set delay time.
5.0 V, 3.3 V, "2%, 150 mA output. Use 22 mF, ESR t 5.0 W to ground.
Input. Battery Supply Input Voltage.
Sense Input. Can provide an early warning signal of an impending reset condition when used with SO.
http://onsemi.com
3
NCV4299
MAXIMUM RATINGS
Rating
Symbol
Min
Max
Unit
Input Voltage to Regulator (DC)
VI
−40
45
V
Input Peak Transient Voltage to Regulator wrt GND
−
−
60
V
VINH
−40
45
V
Sense Input (SI)
VSI
−0.3
45
V
Sense Input (SI)
ISI
−1.0
1.0
mA
Reset Threshold (RADJ)
VRADJ
−0.3
7.0
V
Reset Threshold (RADJ)
IRADJ
−10
10
mA
VD
−0.3
7.0
V
Reset Output (RO)
VRO
−0.3
7.0
V
Sense Output (SO)
VSO
−0.3
7.0
V
Output (Q)
VQ
−0.3
16
V
Output (Q)
IQ
−5.0
−
mA
ESD Capability, Human Body Model (Note 3)
ESDHB
2.0
−
kV
ESD Capability, Machine Model (Note 3)
ESDMM
200
−
V
ESD Capability, Charged Device Model (Note 3)
ESDCDM
1.0
−
kV
Junction Temperature
TJ
−
150
°C
Storage Temperature
Tstg
−50
150
°C
4.5
4.4
45
45
−40
150
−
265 Pk
Inhibit (INH) (Note 1)
Reset Delay (D)
OPERATING RANGE
Input Voltage
5.0 V Version
3.3 V Version
VI
Junction Temperature
TJ
V
°C
LEAD TEMPERATURE SOLDERING REFLOW (Note 2)
Reflow (SMD styles only), lead free
60s−150 sec above 217, 40 sec max at peak
TSLD
Moisture Sensitivity Level
MSL
°C
Level 1
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. 14 pin package only.
2. Per IPC / JEDEC J−STD−020C.
3. This device series incorporates ESD protection and is tested by the following methods:
ESD HBM tested per AEC−Q100−002 (EIA/JESD22−A114)
ESD MM tested per AEC−Q100−003 (EIA/JESD22−A115)
ESD CDM tested per EIA/JES D22/C101, Field Induced Charge Model.
THERMAL CHARACTERISTICS
Characteristic
SO−8
SO−14
Test Conditions (Typical Value)
Note 4
Note 5
Note 6
Junction−to−Tab (yJLx, qJLx)
Junction−to−Ambient (RθJA, qJA)
54
172
52
144
48
118
Junction−to−Tab (yJLx, qJLx)
Junction−to−Ambient (RθJA, qJA)
19
112
21
89
20
67
4. 2 oz Copper, 50 mm sq Copper area, 1.5 mm thick FR4
5. 2 oz Copper, 150 mm sq Copper area, 1.5 mm thick FR4
6. 2 oz Copper, 500 mm sq Copper area, 1.5 mm thick FR4
http://onsemi.com
4
Unit
°C/W
°C/W
NCV4299
ELECTRICAL CHARACTERISTICS (−40°C < TJ < 150°C; VI = 13.5 V unless otherwise noted.)
Characteristic
Symbol
Test Conditions
Min
Typ
Max
Unit
Output Q
Output Voltage (5.0 V Version)
VQ
1.0 mA < IQ < 150 mA, 6.0 V < VI < 16 V
4.9
5.0
5.1
V
Output Voltage (3.3 V Version)
VQ
1.0 mA < IQ < 150 mA, 5.5 V < VI < 16 V
3.23
3.3
3.37
V
Current Limit
IQ
250
400
500
mA
Quiescent Current (Iq = II – IQ)
Iq
INH ON, IQ < 1.0 mA, TJ = 25°C
−
86
100
mA
Quiescent Current (Iq = II – IQ)
Iq
INH ON, IQ < 1.0 mA
−
90
105
mA
Quiescent Current (Iq = II – IQ)
Iq
INH ON, IQ = 10 mA
−
170
500
mA
Quiescent Current (Iq = II – IQ)
Iq
INH ON, IQ = 50 mA
−
0.7
2.0
mA
Quiescent Current (Iq = II – IQ)
Iq
INH = 0 V, TJ = 25°C
−
−
1.0
mA
IQ = 100 mA
−
0.22
0.50
V
Dropout Voltage (Note 7)
Vdr
−
Load Regulation
DVQ
IQ = 1.0 mA to 100 mA
−
5.0
30
mV
Line Regulation
DVQ
VI = 6.0 V to 28 V, IQ = 1.0 mA
−
10
25
mV
ƒr = 100 Hz, Vr = 1.0 Vpp, IQ = 100 mA
−
66
−
dB
VQ < 1.0 V
−
−
0.8
V
VQ > 4.85 V
VQ > 3.2 V
3.5
3.5
−
−
−
−
−
−
3.0
0.5
10
2.0
4.50
2.96
4.64
3.04
4.80
3.16
10
20
40
−
−
0.17
0.17
0.40
0.40
5.6
−
−
kW
Power Supply Ripple Rejection
PSRR
Inhibit (INH) (14 Pin Package Only)
Inhibit Off Voltage
VINHOFF
Inhibit On Voltage
5.0 V Version
3.3 V Version
VINHON
Input Current
IINHON
IINHOFF
INH ON
INH = 0 V
V
mA
Reset (RO)
Switching Threshold
5.0 V Version
3.3 V Version
VRT
−
Output Resistance
RRO
−
Reset Output Low Voltage
5.0 V Version
3.3 V Version
VRO
Allowable External Reset Pullup Resistor
VROext
Q < 4.5 V, Internal RRO, IRO = −1.0 mA
Q < 2.96 V, Internal RRO, IRO = −1.0 mA
External Resistor to Q
V
kW
V
Delay Upper Threshold
VUD
−
1.5
1.85
2.2
V
Delay Lower Threshold
VLD
−
0.4
0.5
0.6
V
7. Measured when the output voltage VQ has dropped 100 mV from the nominal value obtained at VI = 13.5 V.
http://onsemi.com
5
NCV4299
ELECTRICAL CHARACTERISTICS (continued) (−40°C < TJ < 150°C; VI = 13.5 V unless otherwise noted.)
Characteristic
Symbol
Test Conditions
Min
Typ
Max
−
−
−
0.017
0.1
0.1
Q < 4.5 V, Internal RRO, VD = 1.0 V
Q < 2.96 V, Internal RRO, VD = 1.0 V
4.0
−
7.1
−
12
−
Unit
Reset (RO)
VD,sat
Delay Output Low Voltage
5.0 V Version
3.3 V Version
Q < 4.5 V, Internal RRO
Q < 2.96 V, Internal RRO
V
Delay Charge Current
5.0 V Version
3.3 V Version
ID
Power On Reset Delay Time
td
CD = 100 nF
17
28
35
ms
tRR
CD = 100 nF
0.5
2.2
4.0
ms
Q > 3.5 V
Q > 2.3 V
1.26
−
1.36
−
1.44
−
Reset Reaction Time
Reset Adjust Switching Threshold
5.0 V Version
3.3 V Version
VRADJ,TH
mA
V
Input Voltage Sense (SI and SO)
Sense Input Threshold High
VSI,High
−
1.34
1.45
1.54
V
Sense Input Threshold Low
VSI,Low
−
1.26
1.36
1.44
V
50
90
130
mV
Sense Input Hysteresis
−
(Sense Threshold High) −
(Sense Threshold Low)
Sense Input Current
ISI
−
−1.0
0.1
1.0
mA
Sense Output Resistance
RSO
−
10
20
40
kW
Sense Output Low Voltage
VSO
−
0.1
0.4
V
VSI < 1.20 V, VI > 4.2 V, ISO = 0 mA
Allowable External Sense Out
Pullup Resistor
RSOext
−
5.6
−
−
kW
SI High to SO High Reaction Time
tPSOLH
−
−
4.4
8.0
ms
SI Low to SO Low Reaction Time
tPSOHL
−
−
3.8
5.0
ms
II
IQ
VI
IINH
Q
D
CD
100 nF
VRADJ
VSI
IRADJ
ISI
VQ
INH
(14−Pin Part Only)
NCV4299
VINH
I
ID
RADJ
SI
RO
VRO
SO
VSO
GND
Iq
Figure 3. Measurement Circuit
http://onsemi.com
6
NCV4299
TYPICAL PERFORMANCE CHARACTERISTICS − 5.0 V OPTION
6
VI = 13.5 V
RL = 1 kW
VQ, OUTPUT VOLTAGE (V)
VQ, OUTPUT VOLTAGE (V)
5.1
5.0
4.9
−40 −20
5
4
3
2
1
0
0
20 40
60 80 100 120 140 160
TJ, JUNCTION TEMPERATURE (°C)
RL = 50 W
0
500
VI = 13.5 V
VD = 1 V
RL = 5 kW
Vdr, DROP VOLTAGE (mV)
ID, CHARGE CURRENT (mA)
8.0
7.0
6.0
−40 −20
125°C
400
25°C
300
−40°C
200
100
0
20 40
60 80 100 120 140 160
0
TJ, JUNCTION TEMPERATURE (°C)
0
3.2
150
1.5
VI = 13.5V
2.8
2.4
VUD
1.6
1.2
VLD
0.4
0.0
−40
100
50
IQ, OUTPUT CURRENT (mA)
Figure 7. Drop Voltage vs. Output Current
80
0
40
120
TJ, JUNCTION TEMPERATURE (°C)
160
VRADJ,TH, RESET ADJUST SWITCHING
THRESHOLD (V)
VUD, VLD, SWITCHING VOLTAGE (V)
Figure 6. Charge Current vs. Junction
Temperature
0.8
15
Figure 5. Output Voltage vs. Input Voltage
Figure 4. Output Voltage vs. Junction Temperature
2.0
10
5
VI, INPUT VOLTAGE (V)
Figure 8. Switching Voltage vs. Junction
Temperature
1.4
1.3
1.2
1.1
1.0
0.9
−40
0
40
120
80
TJ, JUNCTION TEMPERATURE (°C)
160
Figure 9. Reset Adjust Switching Threshold vs.
Junction Temperature
http://onsemi.com
7
NCV4299
350
VSI,High
1.5
1.4
VSI,Low
1.3
1.2
1.1
1.0
−40
300
IQ, OUTPUT CURRENT (mA)
VSI, SENSE THRESHOLD (V)
1.6
40
120
0
80
TJ, JUNCTION TEMPERATURE (°C)
TJ = 25°C
250
TJ = 125°C
200
150
100
50
0
160
VQ = 0 V
0
Iq, CURRENT CONSUMPTION (mA)
Iq, CURRENT CONSUMPTION (mA)
2.0
1.5
1.0
0.5
0
10
30
20
40
IQ, OUTPUT CURRENT (mA)
50
6.0
4.0
2.0
0.0
60
0
Iq, CURRENT CONSUMPTION (mA)
RRO, RSO, RESISTANCE (kW)
40
120
80
IQ, OUTPUT CURRENT (mA)
160
Figure 13. Current Consumption vs. Output
Current
40
VI = 13.5V
RL = 5 kW
30
20
0
120
40
80
TJ, JUNCTION TEMPERATURE (°C)
40
8.0
Figure 12. Current Consumption vs. Output
Current
10
−40
20
30
VI, INPUT VOLTAGE (V)
Figure 11. Output Current Limit vs. Input
Voltage
Figure 10. Sense Threshold vs. Junction
Temperature
0.0
10
16.0
14.0
12.0
10.0
RL 50W
RL 33W
6.0
4.0
2.0
0.0
160
RL 200W RL 100W
8.0
0
Figure 14. RRO, RSO Resistance vs. Junction
Temperature
10
30
20
VI, INPUT VOLTAGE (V)
Figure 15. Current Consumption vs. Input
Voltage
http://onsemi.com
8
40
Iq, CURRENT CONSUMPTION (mA)
90
85
80
IQ = 100 mA
75
70
65
60
6
8
10
18 20
12 14 16
VI, INPUT VOLTAGE (V)
24
22
6
5
3
IQ = 10 mA
2
1
6
8
18 20
12 14 16
VI, INPUT VOLTAGE (V)
10
VI = 13.5V
TA = 25°C
40
Unstable
Region
30
1 mF to 100 mF
0.1 mF
25
20
15
Stable
Region
10
5
0
0
20
22
24
Figure 17. Current Consumption vs. Input
Voltage
45
35
IQ = 100 mA
4
0
26
IQ = 50 mA
Figure 16. Current Consumption vs. Input
Voltage
OUTPUT CAPACITOR ESR (W)
Iq, CURRENT CONSUMPTION (mA)
NCV4299
Unstable Region
0.1 mF Only
40
60
80
100 120
IQ, OUTPUT CURRENT (mA)
140
Figure 18. Output Stability vs. Output Capacitor
ESR
http://onsemi.com
9
160
26
NCV4299
TYPICAL PERFORMANCE CHARACTERISTICS − 3.3 V OPTION
12
Iq, CURRENT CONSUMPTION (mA)
Iq, CURRENT CONSUMPTION (mA)
1000
VI = 13.5 V
100
IQ = 1 mA
10
1
0.1
−40 −20
0
20
40
60
100 120 140 160
80
TJ = 25°C
TJ = 150°C
TJ = −40°C
4
2
0
0
20
40
60
80
100 120 140 160 180 200
Figure 19. Current Consumption vs. Junction
Temperature
Figure 20. Current Consumption vs. Output
Current
3.5
VQ, OUTPUT VOLTAGE (V)
4
3
RL = 33 W
2
RL = 50 W
RL = 200 W
1
0
10
20
RL = 100 W
30
40
3.3
3.2
3.1
3.0
0
40
80
120
VI, INPUT VOLTAGE (V)
TJ, JUNCTION TEMPERATURE (°C)
Figure 21. Current Consumption vs. Input
Voltage
Figure 22. Output Voltage vs. Junction
Temperature
0
VI = 0 V
−50
TJ = 125°C
−100
−150
TJ = 25°C
−200
TJ = −40°C
−250
0
VI = 13.5V
RL = 1 kW
3.4
2.9
−40
50
IQ, MAXIMUM OUTPUT CURRENT (mA)
Iq, CURRENT CONSUMPTION (mA)
IQ, REVERSE OUTPUT CURRENT (mA)
6
IQ, OUTPUT CURRENT (mA)
TJ = 25°C
−300
8
TJ, JUNCTION TEMPERATURE (°C)
5
0
10
10
20
30
40
50
160
350
300
TJ = 25°C
250
TJ = 125°C
200
150
100
50
0
VQ = 0 V
0
25
VQ, OUTPUT VOLTAGE (V)
VI, INPUT VOLTAGE (V)
Figure 23. Reverse Output Current vs. Output
Voltage
Figure 24. Maximum Output Current vs. Input
Voltage
http://onsemi.com
10
50
NCV4299
6
1000
OUTPUT CAPACITOR ESR (W)
VQ, OUTPUT VOLTAGE (V)
TJ = 25°C
5
RL = 50 W
4
3
2
1
0
0
1
2
4
3
Stable Region
0.1
CQ = 22 mF
TJ = 150°C
0
10
40
70
100
130
Figure 25. Output Voltage at Input Voltage
Extremes
Figure 26. 3.3 V Output Stability with Output
Capacitor ESR
160
0.02
IINH, INHIBIT INPUT CURRENT (mA)
OUTPUT CAPACITOR ESR (W)
1
IQ, OUTPUT CURRENT (mA)
Max ESR for Vin = 6 V
Max ESR for Vin = 25 V
10
1
Stable Region
0.1
CQ = 22 mF
TJ = −40°C
0
10
40
70
100
130
160
TJ = −40°C
0
TJ = 25°C
TJ = 125°C
−0.01
−0.02
−0.03
−0.04
−0.05
TJ = 150°C
0
10
20
30
40
VI, INPUT VOLTAGE (V)
Figure 27. 3.3 V Output Stability with Output
Capacitor ESR
Figure 28. Inhibit Input Current at Input
Voltage Extremes
VRT, RESET TRIGGER THRESHOLD (V)
TJ = −40°C
5
TJ = 25°C
4
TJ = 125°C
3
2
1
0
INH = OFF
0.01
IQ, OUTPUT CURRENT (mA)
6
IINH, INHIBIT INPUT CURRENT (mA)
Max ESR for Vin = 25 V
VI, INPUT VOLTAGE (V)
100
0
Max ESR for Vin = 6 V
10
0.01
5
1000
0.01
100
10
20
30
50
40
3.25
VI = 13.5 V
3.20
3.15
3.10
3.05
Reset
3.00
2.95
−40 −20
0
20
40
60
80
100 120 140 160
VINH, INHIBIT INPUT VOLTAGE (V)
TJ, JUNCTION TEMPERATURE (°C)
Figure 29. Inhibit Input Current at Inhibit Input
Voltage Extremes
Figure 30. Reset Trigger Threshold vs.
Junction Temperature
http://onsemi.com
11
50
NCV4299
VI = 13.5 V
CD = 100 nF
25
20
15
0
20
40
60
80
VI = 13.5 V
VSI High
1.45
1.40
VSI Low
1.35
1.30
−40 −20
100 120 140 160
0
20
40
60
80
100 120 140 160
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 31. Reset Delay Time vs. Junction
Temperature
Figure 32. Sense Threshold vs. Junction
Temperature
8
1.15
7
1.14
Vdr, DROP VOLTAGE (V)
ID, DELAY CAPACITOR CHARGE
CURRENT (mA)
10
−40 −20
6
5
4
3
2
VI = 13.5 V
VD = 1 V
1
0
−40 −20
VUD, VLD, SWITCHING VOLTAGE (V)
VSI, SENSE THRESHOLD (V)
30
1.50
0
20
40
60
80
100 120
TJ = 125°C
1.13
1.12
1.11
1.10
TJ = −40°C
1.09
TJ = 25°C
1.08
1.07
1.06
1.05
140 160
Vdr = VImin − VQ
0
40
80
120
160
TJ, JUNCTION TEMPERATURE (°C)
IQ, OUTPUT CURRENT (mA)
Figure 33. Delay Capacitor Charge Current vs.
Junction Temperature
Figure 34. Drop Voltage vs. Output Current
3.0
VI = 13.5 V
2.5
2.0
VUD
1.5
1.0
VLD
0.5
0
−40
0
40
80
160
120
VRADJ,TH, RESET ADJUST SWITCHING
THRESHOLD (V)
td, RESET DELAY TIME (ms)
35
200
1.5
1.4
1.3
1.2
1.1
1.0
0.9
−40
0
40
80
120
160
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 35. Switching Voltage VUD and VLD vs.
Junction Temperature
Figure 36. Reset Adjust Switching Threshold
vs. Junction Temperature
http://onsemi.com
12
NCV4299
40
TJ = 25°C
RRO, RSO RESISTANCE (kW)
Iq, CURRENT CONSUMPTION (mA)
1.5
1.0
0.5
IQ = 1 mA
IQ = 10 mA
0
0
10
20
30
40
35
30
25
20
15
10
−40
50
0
40
80
120
160
VI, INPUT VOLTAGE (V)
TJ, JUNCTION TEMPERATURE (°C)
Figure 37. Current Consumption vs. Input
Voltage
Figure 38. RRO, RSO Resistance vs. Junction
Temperature
http://onsemi.com
13
NCV4299
APPLICATION DESCRIPTION
NCV4299
Other features of the regulator include an undervoltage
reset function and a sense circuit. The reset function has an
adjustable time delay and an adjustable threshold level. The
sense circuit trip level is adjustable and can be used as an
early warning signal to the controller. An inhibit function
that turns off the regulator and reduces the current
consumption to less than 1.0 mA is a feature available in the
14 pin package.
The NCV4299 is a family of precision micropower
voltage regulators with an output current capability of
150 mA at 5.0 V and 3.3 V.
The output voltage is accurate within "2% with a
maximum dropout voltage of 0.5 V at 100 mA. Low
quiescent current is a feature drawing only 90 mA with a
100 mA load. This part is ideal for any and all battery
operated microprocessor equipment.
Microprocessor control logic includes an active reset
output RO (with delay), and a SI/SO monitor which can be
used to provide an early warning signal to the
microprocessor of a potential impending reset signal. The
use of the SI/SO monitor allows the microprocessor to finish
any signal processing before the reset shuts the
microprocessor down. Internal output resistors on the RO
and SO pins pulling up to the output pin Q reduce external
component count. An inhibit function is available on the
14−lead part. With inhibit active, the regulator turns off and
the device consumes less that 1.0 mA of quiescent current.
The active reset circuit operates correctly at an output
voltage as low as 1.0 V. The reset function is activated
during the powerup sequence or during normal operation if
the output voltage drops outside the regulation limits.
The reset threshold voltage can be decreased by the
connection of an external resistor divider to the RADJ lead.
The regulator is protected against reverse battery, short
circuit, and thermal overload conditions. The device can
withstand load dump transients making it suitable for use in
automotive environments.
Output Regulator
The output is controlled by a precision trimmed reference.
The PNP output has saturation control for regulation while
the input voltage is low, preventing oversaturation. Current
limit and voltage monitors complement the regulator design
to give safe operating signals to the processor and control
circuits.
Stability Considerations
The input capacitor CI is necessary for compensating
input line reactance. Possible oscillations caused by input
inductance and input capacitance can be damped by using a
resistor of approximately 1.0 W in series with CI.
The output or compensation capacitor helps determine
three main characteristics of a linear regulator: startup delay,
load transient response and loop stability.
The capacitor value and type should be based on cost,
availability, size and temperature constraints. A tantalum or
aluminum electrolytic capacitor is best, since a film or
ceramic capacitor with almost zero ESR can cause
instability. The aluminum electrolytic capacitor is the least
expensive solution, but, if the circuit operates at low
temperatures (−25°C to −40°C), both the value and ESR of
the capacitor will vary considerably. The capacitor
manufacturer’s data sheet usually provides this information.
The value for the output capacitor CQ shown in Figures 39
and 40 should work for most applications, however, it is not
necessarily the optimized solution. Stability is guaranteed at
values CQ w 22 mF and an ESR v 5.0 W within the
operating temperature range. Actual limits are shown in a
graph in the typical performance characteristics section.
NCV4299 Circuit Description
The low dropout regulator in the NCV4299 uses a PNP
pass transistor to give the lowest possible dropout voltage
capability. The current is internally monitored to prevent
oversaturation of the device and to limit current during over
current conditions. Additional circuitry is provided to
protect the device during overtemperature operation.
The regulator provides an output regulated to 2%.
http://onsemi.com
14
NCV4299
VBAT
I
CI*
Q
VDD
RRADJ1
0.1 mF
CQ**
22 mF
RADJ
NCV4299
D
CD
Microprocessor
RRADJ2
RS11
SI
RS12
SO
I/O
RO
I/O
GND
*CI required if regulator is located far from the power supply filter.
**CQ required for stability. Cap must operate at minimum temperature expected.
Figure 39. Test and Application Circuit Showing all Compensation and Sense
Elements for the 8 Pin Package Part
VBAT
I
CI*
Q
VDD
RRADJ1
0.1 mF
CQ**
22 mF
RADJ
INH
RINH***
51kW
CINH***
0.01 mF
Microprocessor
D
CD
NCV4299
RRADJ2
RS11
SI
RS12
INH
SO
I/O
RO
I/O
GND
*CI required if regulator is located far from the power supply filter.
**CQ required for stability. Cap must operate at minimum temperature expected.
***This RC filter is only required when transients with slew rate in excess of 10 V/ms may be present on the INH
voltage source during operation. The filter is not required when INH is connected to a noise−free DC voltage.
Figure 40. Test and Application Circuit Showing all Compensation and Sense
Elements for the 14 Pin Package Part with Inhibit Function
http://onsemi.com
15
NCV4299
Reset Output (RO)
the delay timer (VD) drops below the lower threshold
voltage VLD, the reset output voltage VRO is brought low to
reset the processor.
The reset output RO is an open collector NPN transistor,
controlled by a low voltage detection circuit. The circuit is
functionally independent of the rest of the IC, thereby
guaranteeing that RO is valid for VQ as low as 1.0 V.
A reset signal, Reset Output (RO, low voltage) is
generated as the IC powers up. After the output voltage VQ
increases above the reset threshold voltage VRT, the delay
timer D is started. When the voltage on the delay timer VD
passes VUD, the reset signal RO goes high. A discharge of
the delay timer (VD) is started when VQ drops and stays
below the reset threshold voltage VRT. When the voltage of
VI
t
< tRR
VQ
VRT
t
dV
I
+ D
dt
CD
VD
VUD
VLD
td
t
tRR
VRO
VRO,SAT
Power−on−Reset
t
Thermal
Shutdown
Voltage Dip
at Input
Undervoltage
Secondary
Spike
Overload
at Output
Figure 41. Reset Timing Diagram
Reset Adjust (RADJ)
Reset Delay (D)
The reset threshold VRT can be decreased from a typical
value of 4.64 V to as low as 3.5 V by using an external
voltage divider connected from the Q lead to the pin RADJ,
as shown in Figures 39 and 40. The resistor divider keeps the
voltage above the VRADJ,TH, (typ. 1.36 V), for the desired
input voltages and overrides the internal threshold detector.
Adjust the voltage divider according to the following
relationship:
The reset delay circuit provides a delay (programmable by
capacitor CD) on the reset output RO lead. The delay lead D
provides charge current ID (typically 7.1 mA) to the external
delay capacitor CD during the following times:
1. During Powerup (once the regulation threshold has
been exceeded).
2. After a reset event has occurred and the device
is back in regulation. The delay capacitor is
set to discharge when the regulation (VRT, reset
threshold voltage) has been violated. When
the delay capacitor discharges to down to VLD,
the reset signal RO pulls low.
VTHRES + VRADJ, TH · (RADJ1 ) RADJ2)ńRADJ2
(eq. 1)
If the reset adjust option is not needed, the RADJ−pin
should be connected to GND causing the reset threshold to
go to its default value (typ. 4.64 V).
http://onsemi.com
16
NCV4299
Setting the Delay Time
Sense Input (SI)/Sense Output (SO) Voltage Monitor
The delay time is set by the delay capacitor CD and the
charge current ID. The time is measured by the delay
capacitor voltage charging from the low level of VD,sat to the
higher level VUD. The time delay follows the equation:
An on−chip comparator is available to provide early
warning to the microprocessor of a possible reset signal. The
reset signal typically turns the microprocessor off
instantaneously. This can cause unpredictable results with
the microprocessor. The signal received from the SO pin will
allow the microprocessor time to complete its present task
before shutting down. This function is performed by a
comparator referenced to the band gap voltage. The actual
trip point can be programmed externally using a resistor
divider to the input monitor (SI) (Figures 39 and 40). The
typical threshold is 1.35 V on the SI Pin.
(eq. 2)
td + [CD (VUD−VD, sat)]ńID
Example:
Using CD = 100 nF.
Use the typical value for VD,sat = 0.1 V.
Use the typical value for VUD = 1.85 V.
Use the typical value for Delay Charge Current ID = 7.1 mA.
(eq. 3)
td + [100 nF(1.85−0.1 V)]ń7.1 mA + 24.6 ms
Signal Output
When the output voltage VQ drops below the reset
threshold voltage VRT, the voltage on the delay capacitor VD
starts to drop. The time it takes to drop below the lower
threshold voltage of VLD is the reset reaction time, tRR. This
time is typically 2.2 ms for a delay capacitor of 0.1 mF. The
reset reaction time can be estimated from the following
relationship:
tRR + 22 nsńnF
Figure 42 shows the SO Monitor waveforms as a result of
the circuits depicted in Figures 39 and 40. As the output
voltage VQ falls, the monitor threshold VSI,Low is crossed.
This causes the voltage on the SO output to go low sending
a warning signal to the microprocessor that a reset signal may
occur in a short period of time. TWARNING is the time the
microprocessor has to complete the function it is currently
working on and get ready for the reset shutdown signal.
(eq. 4)
CD
Sense
Input
Voltage
VSI,High
VQ
VSI,Low
VSI
VSI,Low
Sense
Output
VRO
t
tPSOLH
tPSOHL
High
VSO
Low
TWARNING
t
Figure 42. SO Warning Timing Waveform
Figure 43. Sense Timing Diagram
Calculating Power Dissipation in a Single Output
Linear Regulator
Iq is the quiescent current the regulator consumes at IQ(max).
Once the value of PD(max) is known, the maximum
permissible value of RqJA can be calculated:
The maximum power dissipation for a single output
regulator is:
RqJA + (150° C−TA)ńPD
PD(max) + [VI(max)−VQ(min)] IQ(max) ) VI(max)Iq
(eq. 6)
The value of RqJA can then be compared with those in the
package section of the data sheet. Those packages with
RqJA’s less than the calculated value in Equation 6 will keep
the die temperature below 150°C. In some cases, none of the
packages will be sufficient to dissipate the heat generated by
the IC, and an external heatsink will be required.
(eq. 5)
where:
VI(max) is the maximum input voltage,
VQ(min) is the minimum output voltage,
IQ(max) is the maximum output current for the application,
and
http://onsemi.com
17
NCV4299
Heatsinks
where:
A heatsink effectively increases the surface area of the
package to improve the flow of heat away from the IC and
into the surrounding air.
Each material in the heat flow path between the IC and the
outside environment will have a thermal resistance. Like
series electrical resistances, these resistances are summed to
determine the value of RqJA:
RqJA + RqJC ) RqCS ) RqSA
RqJC = the junction−to−case thermal resistance,
RqCS = the case−to−heatsink thermal resistance, and
RqSA = the heatsink−to−ambient thermal resistance.
RqJC appears in the package section of the data sheet. Like
RqJA, it too is a function of package type. RqCS and RqSA are
functions of the package type, heatsink and the interface
between them. These values appear in heatsink data sheets
of heatsink manufacturers. Thermal, mounting, and
heatsinking are discussed in the ON Semiconductor
application note AN1040/D, available on the
ON Semiconductor website.
(eq. 7)
http://onsemi.com
18
NCV4299
SOIC 8 LEAD
1000
Cu Area = 10 mm2, 1.0 oz
R(t) (°C/W)
100
25 mm2, 1.0 oz
100 mm2, 1.0 oz
10
250 mm2, 1.0 oz
500 mm2, 1.0 oz
1
0.1
0.000001 0.00001
0.0001
0.001
0.01
0.1
1
10
100
1000
100
1000
Time (sec)
Figure 44. Transient Thermal Response Simulation to a Single Pulse 1 oz (Log−Log)
1000
R(t) (°C/W)
100
50% Duty Cycle
20%
10%
10
5%
2%
1 1%
0.1
Single Pulse (SOIC−8)
0.01
0.001
Psi LA (SOIC−8)
0.000001 0.00001
0.0001
0.001
0.01
0.1
1
10
Pulse Time (sec)
Figure 45. Transient Thermal Response Simulation to a Single Pulse with Duty Cycles Applied (Log−Log)
(PCB = 50 mm2 1 oz)
R(t) (°C/W)
1000
100 50% Duty Cycle
20%
10%
10
5%
2%
1 1%
0.1
Single Pulse (SOIC−8)
0.01
0.001
Psi LA (SOIC−8)
0.000001 0.00001
0.0001
0.001
0.01
0.1
1
10
100
Pulse Time (sec)
Figure 46. Transient Thermal Response Simulation to a Single Pulse with Duty Cycles Applied (Log−Log)
(PCB = 250 mm2 1 oz)
http://onsemi.com
19
1000
NCV4299
SOIC 14 LEAD
1000
Cu Area = 10 mm2, 1.0 oz
R(t) (°C/W)
100
25 mm2, 1.0 oz
100 mm2, 1.0 oz
10
250 mm2, 1.0 oz
500 mm2, 1.0 oz
1
0.1
0.000001 0.00001
0.0001
0.001
0.01
0.1
1
10
100
1000
100
1000
Time (sec)
Figure 47. Transient Thermal Response Simulation to a Single Pulse 1 oz (Log−Log)
R(t) (°C/W)
1000
100 50% Duty Cycle
20%
10%
10 5%
2%
1
1%
0.1 Single Pulse (SOIC−14)
0.01
0.001
Psi LA (SOIC−14)
0.000001 0.00001
0.0001
0.001
0.01
0.1
1
10
Pulse Time (sec)
Figure 48. Transient Thermal Response Simulation to a Single Pulse with Duty Cycles Applied (Log−Log)
(PCB = 50 mm2 1 oz)
100
R(t) (°C/W)
50% Duty Cycle
10 20%
10%
5%
1 2%
1%
0.1 Single Pulse (SOIC−14)
0.01
0.001
Psi LA (SOIC−14)
0.000001 0.00001
0.0001
0.001
0.01
0.1
1
10
100
Pulse Time (sec)
Figure 49. Transient Thermal Response Simulation to a Single Pulse with Duty Cycles Applied (Log−Log)
(PCB = 250 mm2 1 oz)
http://onsemi.com
20
1000
NCV4299
ORDERING INFORMATION
Package
Shipping†
NCV4299D1G
SO−8
(Pb−Free)
98 Units/Rail
NCV4299D1R2G
SO−8
(Pb−Free)
2500 Tape & Reel
NCV4299D2G
SO−14
(Pb−Free)
55 Units/Rail
NCV4299D2R2G
SO−14
(Pb−Free)
2500 Tape & Reel
NCV4299D233G
SO−14
(Pb−Free)
55 Units/Rail
NCV4299D233R2G
SO−14
(Pb−Free)
2500 Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
21
NCV4299
PACKAGE DIMENSIONS
SOIC−8 NB
CASE 751−07
ISSUE AJ
−X−
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. 751−01 THRU 751−06 ARE OBSOLETE. NEW
STANDARD IS 751−07.
A
8
5
S
B
0.25 (0.010)
M
Y
M
1
4
−Y−
K
G
C
N
DIM
A
B
C
D
G
H
J
K
M
N
S
X 45 _
SEATING
PLANE
−Z−
0.10 (0.004)
H
D
0.25 (0.010)
M
Z Y
S
X
M
J
S
SOLDERING FOOTPRINT*
1.52
0.060
7.0
0.275
4.0
0.155
0.6
0.024
1.270
0.050
SCALE 6:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
22
MILLIMETERS
MIN
MAX
4.80
5.00
3.80
4.00
1.35
1.75
0.33
0.51
1.27 BSC
0.10
0.25
0.19
0.25
0.40
1.27
0_
8_
0.25
0.50
5.80
6.20
INCHES
MIN
MAX
0.189
0.197
0.150
0.157
0.053
0.069
0.013
0.020
0.050 BSC
0.004
0.010
0.007
0.010
0.016
0.050
0 _
8 _
0.010
0.020
0.228
0.244
NCV4299
PACKAGE DIMENSIONS
SOIC−14
CASE 751A−03
ISSUE H
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE
DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.127
(0.005) TOTAL IN EXCESS OF THE D
DIMENSION AT MAXIMUM MATERIAL
CONDITION.
−A−
14
8
−B−
P 7 PL
0.25 (0.010)
B
M
7
1
G
−T−
0.25 (0.010)
M
T B
S
A
DIM
A
B
C
D
F
G
J
K
M
P
R
J
M
K
D 14 PL
F
R X 45 _
C
SEATING
PLANE
M
S
MILLIMETERS
MIN
MAX
8.55
8.75
3.80
4.00
1.35
1.75
0.35
0.49
0.40
1.25
1.27 BSC
0.19
0.25
0.10
0.25
0_
7_
5.80
6.20
0.25
0.50
INCHES
MIN
MAX
0.337 0.344
0.150 0.157
0.054 0.068
0.014 0.019
0.016 0.049
0.050 BSC
0.008 0.009
0.004 0.009
0_
7_
0.228 0.244
0.010 0.019
SOLDERING FOOTPRINT
7X
7.04
14X
1.52
1
14X
0.58
1.27
PITCH
DIMENSIONS: MILLIMETERS
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
23
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCV4299/D