Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK HMC454ST89 / 454ST89E v05.0710 9 InGaP HBT ½ WATT HIGH IP3 AMPLIFIER, 0.4 - 2.5 GHz Typical Applications Features The HMC454ST89 / HMC454ST89E is ideal for applications requiring a high dynamic range amplifier: Output IP3: +40 to +42 dBm • GSM, GPRS & EDGE 50% PAE @ +28 dBm Pout • CDMA & W-CDMA +17.5 dBm W-CDMA Channel Power@ -45 dBc ACP • CATV/Cable Modem Single +5V Supply • Fixed Wireless & WLL Industry Standard SOT89 Package Gain: 12.5 dB @ 2150 MHz AMPLIFIERS - LINEAR & POWER - SMT Included in the HMC-DK002 Designer’s Kit Functional Diagram General Description The HMC454ST89 & HMC454ST89E are high dynamic range GaAs InGaP Heterojunction Bipolar Transistor (HBT) ½ watt MMIC amplifiers operating between 0.4 and 2.5 GHz. Packaged in a low cost industry standard SOT89, the amplifier gain is typically 17.8 dB from 0.8 to 1.0 GHz and 12.5 dB from 1.8 to 2.2 GHz. Utilizing a minimum number of external components and a single +5V supply, the amplifier output IP3 can be optimized to +40 dBm at 0.9 GHz or +42 dBm at 2.0 GHz. The high output IP3 and PAE makes the HMC454ST89 an ideal driver amplifier for Cellular/PCS/3G, WLL, ISM and Fixed Wireless applications. Electrical Specifi cations, TA = +25°C, Vs= +5V [1] Parameter Min. Frequency Range Gain Typ. Max. Min. 824 - 960 16 Gain Variation Over Temperature 17.8 0.008 Typ. Max. Min. 1800 - 2000 11 0.016 12.5 0.008 Typ. Max. 2000 - 2200 11 0.016 MHz 12.5 0.008 Units dB 0.016 dB / °C Input Return Loss 9 7 12 Output Return Loss 13 21 19 dB 27.5 dBm Output Power for 1dB Compression (P1dB) 22 Saturated Output Power (Psat) Output Third Order Intercept (IP3) [2] Noise Figure Supply Current (Icq) 24.5 24 25.5 37 24 28.5 40 38 8 150 27 41 38 6.5 175 150 dB 28.5 dBm 42 dBm 5.2 175 150 dB 175 mA [1] Specifications and data reflect HMC454ST89 measured using the respective application circuits for each designated frequency band found herein. Contact the HMC Applications Group for assistance in optimizing performance for your application. [2] Two-tone input power of 0 dBm per tone, 1 MHz spacing. 9 - 190 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC454ST89 / 454ST89E v05.0710 InGaP HBT ½ WATT HIGH IP3 AMPLIFIER, 0.4 - 2.5 GHz Gain vs. Temperature @ 900 MHz 25 20 20 19 15 18 17 S21 S11 S22 5 0 -5 13 -15 11 0.6 0.7 0.8 0.9 1 1.1 FREQUENCY (GHz) 1.2 1.3 1.4 0.7 0.8 0.9 1 FREQUENCY (GHz) 1.1 1.2 1.1 1.2 Output Return Loss vs. Temperature @ 900 MHz 0 0 RETURN LOSS (dB) -5 -10 -15 +25 C +85 C -40 C -20 -25 +25 C +85 C -40 C -5 -10 -15 -20 0.8 0.9 1 FREQUENCY (GHz) 1.1 1.2 P1dB vs. Temperature @ 900 MHz 0.7 0.8 0.9 1 FREQUENCY (GHz) Psat vs. Temperature @ 900 MHz 30 30 29 29 28 28 +25 C +85 C -40 C 27 PSAT (dBm) 27 26 25 24 26 25 24 23 23 22 22 21 21 20 0.7 +25 C +85 C -40 C 10 0.5 Input Return Loss vs. Temperature @ 900 MHz 0.7 9 14 12 0.4 RETURN LOSS (dB) 15 -10 -20 P1dB (dBm) 16 AMPLIFIERS - LINEAR & POWER - SMT 10 GAIN (dB) RESPONSE (dB) Broadband Gain & Return Loss @ 900 MHz +25 C +85 C -40 C 20 0.8 0.9 1 FREQUENCY (GHz) 1.1 1.2 0.7 0.8 0.9 1 FREQUENCY (GHz) 1.1 1.2 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 9 - 191 HMC454ST89 / 454ST89E v05.0710 InGaP HBT ½ WATT HIGH IP3 AMPLIFIER, 0.4 - 2.5 GHz Output IP3 vs. Temperature @ 900 MHz Noise Figure vs. Temperature @ 900 MHz 15 43 14 42 13 NOISE FIGURE (dB) 44 9 IP3 (dBm) 41 40 39 38 37 +25 C +85 C -40 C 36 9 8 5 0.8 0.9 1 FREQUENCY (GHz) 1.1 1.2 0.7 0 -5 -10 +25 C +85 C -40 C -15 -20 -25 -30 -35 -40 0.8 0.8 0.9 1 FREQUENCY (GHz) 1.1 1.2 Gain, Power & Output IP3 vs. Supply Voltage @ 900 MHz GAIN (dB), P1dB (dBm), PSAT (dBm), IP3 (dBm) Reverse Isolation vs. Temperature @ 900 MHz 0.9 1 FREQUENCY (GHz) 1.1 1.2 45 40 35 30 25 20 15 GAIN P1dB 10 PSAT IP3 5 4.5 4.75 5 Vs (V) 5.25 5.5 ACPR vs. Supply Voltage @ 880 MHz CDMA IS95, 9 Channels Forward -30 -35 CDMA IS95 Frequency : 880 MHz Integration BW: 1.228 MHz Forward Link, 9 Channels -40 -45 ACPR (dBc) ISOLATION (dB) AMPLIFIERS - LINEAR & POWER - SMT 10 6 34 0.7 +25 C +85 C -40 C 11 7 35 0.7 12 -50 4.5V 5.0V -55 -60 5.5V -65 -70 -75 Source ACPR -80 7 8 9 10 11 12 13 14 15 16 17 18 19 Channel Output Power (dBm) 9 - 192 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC454ST89 / 454ST89E v05.0710 InGaP HBT ½ WATT HIGH IP3 AMPLIFIER, 0.4 - 2.5 GHz Gain vs. Temperature @ 1960 MHz 25 15 20 14 15 13 10 12 S21 S11 S22 0 -5 9 8 -15 7 -20 6 9 +25 C +85 C -40 C 5 1 1.2 1.4 1.6 1.8 2 2.2 2.4 FREQUENCY (GHz) 2.6 2.8 3 Input Return Loss vs. Temperature @ 1960 MHz 1.7 2.1 2.2 2.1 2.2 -5 RETURN LOSS (dB) -10 +25 C +85 C -40 C -15 +25 C +85 C -40 C -10 -15 -20 -25 -20 1.8 1.9 2 FREQUENCY (GHz) 2.1 1.7 2.2 P1dB vs. Temperature @ 1960 MHz 1.8 1.9 2 FREQUENCY (GHz) Psat vs. Temperature @ 1960 MHz 32 32 31 31 30 30 +25 C +85 C -40 C 29 PSAT (dBm) 29 28 27 26 28 27 26 25 25 24 24 23 23 +25 C +85 C -40 C 22 22 1.7 1.9 2 FREQUENCY (GHz) 0 -5 1.7 1.8 Output Return Loss vs. Temperature @ 1960 MHz 0 RETURN LOSS (dB) 10 -10 -25 P1dB (dBm) 11 AMPLIFIERS - LINEAR & POWER - SMT 5 GAIN (dB) RESPONSE (dB) Broadband Gain & Return Loss @ 1960 MHz 1.8 1.9 2 FREQUENCY (GHz) 2.1 2.2 1.7 1.8 1.9 2 FREQUENCY (GHz) 2.1 2.2 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 9 - 193 HMC454ST89 / 454ST89E v05.0710 InGaP HBT ½ WATT HIGH IP3 AMPLIFIER, 0.4 - 2.5 GHz Output IP3 vs. Temperature @ 1960 MHz 10 43 9 42 8 NOISE FIGURE (dB) 44 40 39 38 +25 C +85 C -40 C 37 5 4 +25 C +85 C -40 C 3 2 1 0 1.8 1.9 2 FREQUENCY (GHz) 2.1 2.2 0 -5 +25 C +85 C -40 C -15 -20 -25 1.7 1.8 1.8 1.9 2 FREQUENCY (GHz) 2.1 2.2 Gain, Power & Output IP3 vs. Supply Voltage @ 1960 MHz Reverse Isolation vs. Temperature @ 1960 MHz -10 1.7 1.9 2 FREQUENCY (GHz) 2.1 2.2 ACPR vs. Supply Voltage @ 1.96 GHz CDMA 2000, 9 Channels Forward GAIN (dB), P1dB (dBm), PSAT (dBm), IP3 (dBm) 1.7 ISOLATION (dB) 6 35 45 40 35 30 25 GAIN P1dB 20 PSAT IP3 15 10 5 4.5 4.75 5 Vs (V) 5.25 5.5 ACPR vs. Supply Voltage @ 2.14 GHz W-CDMA, 64 DPCH -30 -40 -45 CDMA2000 Rev. 8 Frequency : 1.96 GHz Integration BW: 1.228 MHz Forward Link, SRI, 9 CHANNELS -50 -35 WCDMA Frequency : 2.14 GHz Integration BW: 3.84 MHz 64 DPCH -40 ACPR (dBc) -55 4.5V -60 5.0V -65 5.5V -70 -45 4.5V -50 5.0V -55 5.5V -60 -75 -65 -80 Source ACPR Source ACPR -70 -85 2 4 6 8 10 12 14 16 Channel Output Power (dBm) 9 - 194 7 36 34 ACPR (dBc) AMPLIFIERS - LINEAR & POWER - SMT IP3 (dBm) 41 9 Noise Figure vs. Temperature @ 1960 MHz 18 20 22 0 2 4 6 8 10 12 14 16 18 20 Channel Output Power (dBm) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC454ST89 / 454ST89E v05.0710 InGaP HBT ½ WATT HIGH IP3 AMPLIFIER, 0.4 - 2.5 GHz Absolute Maximum Ratings +6.0 Vdc RF Input Power (RFIN)(Vs = +5Vdc) +25 dBm Junction Temperature 150 °C Continuous Pdiss (T = 85 °C) (derate 13.6 mW/°C above 85 °C) 0.890 W Thermal Resistance (junction to ground paddle) 73 °C/W Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS 9 Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 4. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 5. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND. AMPLIFIERS - LINEAR & POWER - SMT Collector Bias Voltage (Vcc) Package Information Part Number Package Body Material Lead Finish MSL Rating HMC454ST89 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 HMC454ST89E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 Package Marking [3] [1] H454 XXXX [2] H454 XXXX [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 9 - 195 HMC454ST89 / 454ST89E v05.0710 InGaP HBT ½ WATT HIGH IP3 AMPLIFIER, 0.4 - 2.5 GHz Pin Descriptions AMPLIFIERS - LINEAR & POWER - SMT 9 Pin Number Function Description 1 RFIN This pin is AC coupled. Off chip matching components are required. See Application Circuit herein. 3 RFOUT RF output and DC Bias input for the output amplifier stage. Off chip matching components are required. See Application Circuit herein. 2,4 GND These pins & package bottom must be connected to RF/DC ground. 900 MHz Application Circuit, Compact Layout This circuit was used to specify the performance for 894-960 MHz operation. This circuit will satisfy many applications from 700 to 1200 MHz. Contact the HMC Applications Group for assistance in optimizing performance for your application. TL1 Recommended Component Values 50 Ohm L1, L2 1 nH Physical Length 0.050” L3 36 nH Electrical Length 2.5° R1 5.1 Ohms PCB Material: 10 mil Rogers 4350, Er = 3.48 C1 8 pF Impedance 9 - 196 Interface Schematic C2 22 pF C3 2.7 pF C4, C6 100 pF C5 2.2 μF For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC454ST89 / 454ST89E v05.0710 InGaP HBT ½ WATT HIGH IP3 AMPLIFIER, 0.4 - 2.5 GHz 900 MHz Evaluation PCB List of Materials for Evaluation PCB 107755 [1] Item Description J1 - J2 PCB Mount SMA Connector J3 -J4 DC Pins C1 8 pF Capacitor, 0402 Pkg. C2 22 pF Capacitor, 0402 Pkg. C3 2.7 pF Capacitor, 0402 Pkg. C4, C6 100 pF Capacitor, 0402 Pkg. C5 2.2 μF Capacitor, Tantalum L1, L2 1 nH Inductor, 0402 Pkg. L3 36 nH Inductor, 0402 Pkg. R1 5.1 Ohms U1 HMC454ST89 / HMC454ST89E Linear Amp PCB [2] 107753 Evaluation PCB, 10 mils The circuit board used in this application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation board should be mounted to an appropriate heat sink. The evaluation circuit board shown is available from Hittite upon request. AMPLIFIERS - LINEAR & POWER - SMT 9 [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350, Er = 3.48 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 9 - 197 HMC454ST89 / 454ST89E v05.0710 InGaP HBT ½ WATT HIGH IP3 AMPLIFIER, 0.4 - 2.5 GHz 1960 & 2140 MHz Application Circuit This circuit was used to specify the performance for 1800-2000 and 2000-2200 MHz operation. This circuit will satisfy many applications from 1700 to 2500 MHz. Contact the HMC Applications Group for assistance in optimizing performance for your application. AMPLIFIERS - LINEAR & POWER - SMT 9 9 - 198 TL1 TL2 T3 TL4 Recommended Component Values 50 Ohm 50 Ohm 50 Ohm 50 Ohm L1 8.2 nH Physical Length 0.32” 0.10” 0.07” 0.17” C1 1 pF Electrical Length 34° 11° 8° 18.5° C2 1.2 pF C3 3 pF C4 100 pF C5 2.2 μF Impedance PCB Material: 10 mil Rogers 4350, Er = 3.48 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC454ST89 / 454ST89E v05.0710 InGaP HBT ½ WATT HIGH IP3 AMPLIFIER, 0.4 - 2.5 GHz 1960 & 2140 MHz Evaluation PCB List of Materials for Evaluation PCB 107749 [1] Item Description J1 - J2 PCB Mount SMA Connector J3 - J4 DC Pins C1 1.0 pF Capacitor, 0402 Pkg. C2 1.2 pF Capacitor, 0402 Pkg. C3 3.0 pF Capacitor, 0402 Pkg. C4 100 pF Capacitor, 0402 Pkg. C5 2.2 μF Capacitor, Tantalum L1 8.2 nH Inductor, 0402 Pkg. U1 HMC454ST89 / HMC454ST89E PCB [2] 107747 Evaluation PCB, 10 mils The circuit board used in this application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation board should be mounted to an appropriate heat sink. The evaluation circuit board shown is available from Hittite upon request. AMPLIFIERS - LINEAR & POWER - SMT 9 [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350, Er = 3.48 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 9 - 199 HMC454ST89 / 454ST89E v05.0710 InGaP HBT ½ WATT HIGH IP3 AMPLIFIER, 0.4 - 2.5 GHz Alternative 900 MHz Application Circuit, Optimal OIP3 Layout This alternate application circuit for 900 MHz applications features a resonating I/O structure on the PCB that, while using more PCB area, will improve output IP3 from +40 dBm to +42 dBm. This circuit will satisfy many applications from 700 to 1200 MHz as the typical performance below demonstrates. Contact the HMC Applications Group for assistance in optimizing performance for your application. Recommended Component Values TL1 TL2 TL3 50 Ohm 50 Ohm 50 Ohm Physical Length 0.35” 0.05” 0.53” Electrical Length 18° 2.5° 27° Impedance PCB Material: 10 mil Rogers 4350, Er = 3.48 Broadband Gain & Return Loss IP3 (dBm), P1dB (dBm) 15 10 S21 S11 S22 5 0 -5 4 pF C2, C6 10 pF C3 3 pF C4 100 pF C5 2.2 μF 45 40 IP3 P1dB 35 30 25 -10 -15 9 - 200 18 nH 50 20 0.4 L1 C1 Output IP3 & P1dB 25 RESPONSE (dB) AMPLIFIERS - LINEAR & POWER - SMT 9 20 0.5 0.6 0.7 0.8 0.9 1 1.1 FREQUENCY (GHz) 1.2 1.3 1.4 0.7 0.8 0.9 1 FREQUENCY (GHz) 1.1 1.2 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC454ST89 / 454ST89E v05.0710 InGaP HBT ½ WATT HIGH IP3 AMPLIFIER, 0.4 - 2.5 GHz Alternate 900 MHz Evaluation PCB List of Materials Item Description J1 - J2 PCB Mount SMA Connector J3 - J4 DC Pins C1 4 pF Capacitor, 0402 Pkg. C2, C6 10 pF Capacitor, 0402 Pkg. C3 3.0 pF Capacitor, 0402 Pkg. C4 100 pF Capacitor, 0402 Pkg L1 18 nH Inductor, 0402 Pkg. U1 HMC454ST89 / HMC454ST89E PCB* 107750 Evaluation PCB, 10 mils The circuit board used in this application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation board should be mounted to an appropriate heat sink. The evaluation circuit board shown is available from Hittite upon request. AMPLIFIERS - LINEAR & POWER - SMT 9 * Circuit Board Material: Rogers 4350, Er = 3.48 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 9 - 201