MB/HB SP12T Antenna Switch Module with MIPI I/F CXM3656K Description The CXM3656K is a SP12T antenna switch module for use in a multimode (GSM/UMTS/CDMA/LTE) carrier aggregation (CA) handset or embedded data card application. The CXM3656K consist of an SP12T switch with ten (mid band and high band [MB and HB]) TRx ports and one Tx port with integrated GSM HB LPF and another Tx port supporting GSM HB power and linearity but without integrated LPF. The CXM3656K use MIPI RFFE interface for all device commands and controls. The Sony GaAs junction gate pHEMT (JPHEMT) MMIC process is used for low insertion loss. The device has low BOM with no DC blocking Capacitor. Features Low Insertion Loss: 0.80dB (Typ.) TRx1-4 (2.7GHz) Low Voltage Operation: Vdd=2.5V Supports CMOS control for serial interface No DC Blocking Capacitors except external DC bias Small Package Size: Lead-Free and RoHS Compliant LTCC-24P PKG (2.4mm x 3.2mm x 1.00mm Max.) Structure GaAs Junction Gate pHEMT (JPHEMT) MMIC Switch, CMOS Decoder This IC is ESD sensitive device. Special handling precautions are required. 1 Block Diagram of SP12T Antenna Switch Module 2 Block Diagram of RF Switch Truth Table State 1 2 3 4 5 6 7 8 9 10 11 12 13 Mode Isolation Ant-TRx1 Ant-TRx2 Ant-TRx3 Ant-TRx4 Ant-TRx5 Ant-TRx6 Ant-TRx7 Ant-TRx8 Ant-TRx9 Ant-TRx10 Ant-TxHB2 Ant-TxHB1 Register 0 bits Switch D3 D2 D1 D0 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 F14 F15 F16 F17 F18 F19 F20 F21 F22 F23 F24 0 0 0 0 L L L L L L L L L L L L H H H H H H H H H H H H 0 0 0 1 H L L L L L L L L L L L L H H H H H H H H H H H 0 0 1 0 L H L L L L L L L L L L H L H H H H H H H H H H 0 0 1 1 L L H L L L L L L L L L H H L H H H H H H H H H 0 1 0 0 L L L H L L L L L L L L H H H L H H H H H H H H 0 1 0 1 L L L L H L L L L L L L H H H H L H H H H H H H 0 1 1 0 L L L L L H L L L L L L H H H H H L H H H H H H 0 1 1 1 L L L L L L H L L L L L H H H H H H L H H H H H 1 0 0 0 L L L L L L L H L L L L H H H H H H H L H H H H 1 0 0 1 L L L L L L L L H L L L H H H H H H H H L H H H 1 0 1 0 L L L L L L L L L H L L H H H H H H H H H L H H 1 0 1 1 L L L L L L L L L L H L H H H H H H H H H H L H 1 1 0 0 L L L L L L L L L L L H H H H H H H H H H H H L (*1) State ”L” means a switch “OFF”, State ”H” means a switch “ON” 3 Pin Configuration Absolute Maximum Ratings ◆ Supply voltage VDD 6 V (Ta = 25 °C) VIO, SDATA, SCLK 2.5 V (Ta = 25 °C) [TxHB] 36 dBm (Duty cycle = 12.5 to 50 ) (Ta = 25 °C) [TRx] 32 dBm (Ta = 25 °C) ◆ Operating temperature Topr –35 to +90 °C ◆ Storage temperature Tstg –40 to +125 °C ◆ Control voltage for MIPI ◆ Maximum input 4 Electrical Characteristics Vdd=2.5V , Ta=25degC Item Symbol Path Typ. Max. 1710-1910MHz, 32dBm - 1.54 1.69 Ant - TxHB2 1710-1910MHz, 32dBm - 1.20 1.35 1427-2170MHz, 26dBm - 0.79 0.94 2300-2690MHz, 26dBm - 0.84 1.04 1427-2170MHz, 26dBm - 0.80 0.95 2300-2690MHz, 26dBm - 0.82 1.02 1427-2170MHz, 26dBm - 0.77 0.92 2300-2690MHz, 26dBm - 0.75 0.95 1427-2170MHz, 26dBm - 0.79 0.94 2300-2690MHz, 26dBm - 0.89 1.09 1427-2170MHz, 26dBm - 1.10 1.25 2300-2690MHz, 26dBm - 1.38 1.58 1427-2170MHz, 26dBm - 1.15 1.30 2300-2690MHz, 26dBm - 1.39 1.59 1427-2170MHz, 26dBm - 1.14 1.29 2300-2690MHz, 26dBm - 1.40 1.60 1427-2170MHz, 26dBm - 1.15 1.30 2300-2690MHz, 26dBm - 1.39 1.59 1427-2170MHz, 26dBm - 1.13 1.28 2300-2690MHz, 26dBm - 1.42 1.62 1427-2170MHz, 26dBm - 1.19 1.34 2300-2690MHz, 26dBm - 1.36 1.56 Ant - TRx2 Ant - TRx3 Ant - TRx4 IL Min. Ant - TxHB1 Ant - TRx1 Insertion Loss Condition Ant - TRx5 Ant - TRx6 Ant - TRx7 Ant - TRx8 Ant - TRx9 Ant - TRx10 5 Unit dB Tx/TRx to Tx/TRx Isolation Matrix Vdd=2.5V , Ta=25degC State TxHB1 TxHB1 TxHB1 TxHB1 TxHB2 TxHB2 TxHB2 TxHB2 TRx1 TRx1 TRx1 TRx1 TRx2 TRx2 TRx2 TRx2 TRx3 TRx3 TRx3 TRx3 TRx4 TRx4 TRx4 TRx4 TRx5 TRx5 TRx5 TRx5 TRx6 TRx6 TRx6 TRx6 TRx7 TRx7 TRx7 TRx7 TRx8 TRx8 TRx8 TRx8 TRx9 TRx9 TRx9 TRx9 TRx10 TRx10 TRx10 TRx10 Freq. (GHz) <0.9 <1.9 <2.2 <2.7 <0.9 <1.9 <2.2 <2.7 <0.9 <1.9 <2.2 <2.7 <0.9 <1.9 <2.2 <2.7 <0.9 <1.9 <2.2 <2.7 <0.9 <1.9 <2.2 <2.7 <0.9 <1.9 <2.2 <2.7 <0.9 <1.9 <2.2 <2.7 <0.9 <1.9 <2.2 <2.7 <0.9 <1.9 <2.2 <2.7 <0.9 <1.9 <2.2 <2.7 <0.9 <1.9 <2.2 <2.7 TxHB1 33 32 32 35 40 40 40 39 40 40 40 40 40 40 40 40 40 40 40 40 40 39 37 36 40 40 37 37 40 40 37 37 40 39 37 37 40 39 36 36 40 35 33 32 TxHB2 37 28 28 25 40 38 36 33 40 40 40 37 40 40 40 38 40 40 40 40 40 37 33 30 40 38 33 30 40 38 34 31 40 37 33 30 40 36 32 28 34 29 26 22 TRx1 37 35 36 36 36 32 32 31 40 33 32 32 40 32 31 31 40 33 31 31 39 32 31 29 39 32 31 29 39 33 31 29 40 33 31 29 39 33 31 29 40 33 31 29 TRx2 40 40 39 38 40 40 37 34 40 35 34 31 29 23 22 22 34 27 26 26 40 40 37 33 40 40 37 33 40 40 37 33 40 40 38 34 40 40 38 34 40 40 38 34 TRx3 40 40 40 38 40 40 38 34 40 34 32 31 31 25 25 24 28 22 21 21 40 38 35 32 40 38 36 32 40 39 37 33 40 40 37 33 40 40 38 33 40 40 38 34 Isolation Min. (dB) TRx4 TRx5 TRx6 40 40 40 38 32 34 35 31 32 34 31 32 40 40 40 38 31 34 34 31 32 31 31 31 40 40 40 37 40 40 34 36 38 30 35 37 36 40 40 29 40 40 28 37 39 27 36 37 32 40 40 26 40 40 25 39 40 23 36 36 40 40 40 40 40 40 35 36 40 30 36 25 32 22 29 18 40 35 37 27 32 24 29 20 40 40 28 37 31 23 33 27 21 30 24 17 40 40 38 38 32 30 33 29 27 31 27 24 40 40 40 38 32 33 34 30 30 31 29 27 40 40 40 38 32 34 34 30 31 31 30 29 6 TRx7 40 35 33 33 40 35 33 33 40 40 39 38 40 40 40 38 40 40 40 38 40 40 40 38 36 30 27 24 26 22 20 16 34 28 26 22 40 33 29 26 40 34 32 30 TRx8 40 33 32 31 40 33 32 31 40 40 38 36 40 40 38 36 40 40 39 37 40 40 40 37 40 33 29 26 38 30 27 23 33 27 24 20 33 27 24 20 40 32 29 26 TRx9 40 33 32 31 40 33 31 30 40 40 36 35 40 40 36 35 40 40 38 36 40 40 39 37 40 33 29 26 40 31 28 25 39 30 27 24 30 25 22 19 35 28 25 22 TRx10 40 33 32 32 40 31 29 26 40 40 36 34 40 40 36 35 40 40 37 35 40 40 37 35 40 33 30 27 40 33 29 26 40 32 29 26 39 30 27 24 32 25 23 20 Vdd=2.5V , Ta=25degC Item Symbol VSWR VSWR 2fo 3fo Harmonics 2fo 3fo 2fo 3fo Attenuation ATT IMD2 IMD3 Inter Modulation IIP2 Distortion IIP3 Switching Time Supply Current Ts Idd Ivio Path Condition Min. Typ. Max. Unit - - 1.50 - - - -36 - - -36 - - -60 - - -60 - - -70 - - -80 3420 to 3820MHz 25 - - 5130 to 5730MHz 25 - - 6840 to 12750MHz 20 - - - - -105 - - -105 All Ports Pass band through in Active Paths 1427 to 2690MHz Ant - TxHB1, TxHB2 1910MHz, 32dBm Ant - TRx5-10 1427-2690MHz, 25dBm Ant - TRx1-4 1427-2690MHz, 25dBm Ant - TxHB1 dBm dB Ant - TRx5-10 Table.1 Ant - TRx1-4 Table.2 118 - - Ant - TRx5-10 Table.2 - 118 - Ant - TRx1-4 Table.3 - 80 - Ant – TRx9 Table.3 Ant - TRx5, 6, 7, 8, 10 Table.3 - 73 - TRx1-4 50% Ctl to 90% RF - 6.8 10 us TRx5-10, TxHB1, TxHB2 50% Ctl to 90% RF - 3.7 5 us Active mode Vdd=2.50V - 200 400 uA Low power (Idle) mode Vdd=2.50V - 1 10 uA Stable state Vio=1.80V - 3 10 uA 77 Electrical Characteristics are measured with the recommended circuit with all RF ports terminated in 50 Ohms. 7 dBm Table.1 fRx on TRx Band Band I fTx +20dBm on TRx 2140MHz Band II 1950MHz 1960MHz Band VII 1880MHz 2655MHz 2535MHz fBlocker -15dBm on Ant IMD2(fRx - fTx) 190MHz IMD2(fRx + fTx) 4090MHz IMD3(2fTx - fRx) 1760MHz IMD3(2fTx + fRx) 6040MHz IMD2(fRx - fTx) 80MHz IMD2(fRx + fTx) 3840MHz IMD3(2fTx - fRx) 1800MHz IMD3(2fTx + fRx) 5720MHz IMD2(fRx - fTx) 120Hz IMD2(fRx + fTx) 5190MHz IMD3(2fTx - fRx) 2415MHz IMD3(2fTx + fRx) 7725MHz Table.2 Band Victim band (MHz) CW tone 1 (MHz) CW tone 1 (dBm) CW tone 2 (MHz) CW tone 2 (dBm) B3 742 1715 24.7 2457 7 Band Victim band (MHz) CW tone 1 (MHz) CW tone 1 (dBm) CW tone 2 (MHz) CW tone 2 (dBm) B3 958 1715 24.7 2472 7 B1 965 1975 24.7 4915 2 B34 1578 2020 24.7 2462 7 Table.3 8 Triple Beat Ratio (VDD = 2.5 V, Ta = 25 °C) Condition *1 Item Symbol Path Triple Beat Ratio TBR All TRx port Input power at RF [dBm] Tx1 at RF Tx2 at RF Jammer at Ant -30dBm Triple Beat Product at RF Min. Typ. Max. 21.5 1880MHz 1881MHz 1960MHz 1960±1MHz 81 - - 13.5 1732MHz 1733MHz 2132MHz 2132±1MHz 81 - - Unit dBc Electrical characteristics are measured with all RF ports terminated in 50 . Measured with the recommended circuit IIP2 (VDD = 2.5 V, Ta = 25 °C) Condition Item Input IP2 *1 Symbol IIP2 Path All TRx port Min. Typ. Max. 1965 95.5 - - 80 1965 95.5 - - 1732.5 3865 2132.5 95.5 - - 1732.5 400 2132.5 95.5 - - Tx at TRx* 24dBm Jammer at Ant -20dBm IM2 Product at TRx* 1885 3850 1885 Electrical characteristics are measured with all RF ports terminated in 50 . Measured with the recommended circuit 9 Unit dBm MIPI Specification Parameter Symbol Min. Typ. Max. Unit Supply Voltage VDD 2.5 2.8 3.0 V IDD - 200 400 uA IDD - 1 10 uA VIO 1.65 1.8 1.95 V 3 10 uA Supply current (ACTIVE) *Vdd=2.8V Supply current Low Power(disable) *Vdd=2.8V Interface Supply Voltage Supply current Stable state *Vio=1.8V Ivio Signal level low Vcl 0 - 0.2xVIO V Signal level high Vch 0.8xVIO - VIO V SCLK write Frequency fSCLKw 0.032 19.2 26 MHz SCLK read Frequency fSCLr 0.032 9.6 13 MHz SDATA/SCLK input capacitance Vcl 2 3 pF Data setup time Ts 2 SDATA/SCLK load capacitance Cl 10 Data hold time Th 5 Switching Time * Tsw - - 10 us Turn on Time ** Ton - - 100 us TD - - 10.25 ns TD - - 22 ns ns - 50 pF ns Delay of data line at the slave’s pad output with respect to SCLK for full-rate Delay of data line at the slave’s pad output with respect to SCLK for half-rate 10 Parameter Symbol Min. Typ. Max. Unit TSDataOTR (full-rate) TSDataOTR 2.1 - 6.5 ns TSDataOTR (half-rate) TSDataOTR 2.1 - 10 ns Interface OFF state leakage current ISIG-OFF -1 1 5 uA VVIO-RST 200 400 450 mV VVIO-RST (final at powerdown) VVIO-RST 0 200 mV TVIO-RST(transitionary powerup) TVIO-RST 0.05 20 20 ms TVIO-RST 0.1 1 3 ms TVIO-RST(final phase) TVIO-RST 50 - 450 us TSILOL (final phase) TSILOL 0.12 10 1000 us VVIO-RST(transitionary powerup and powerdown) TVIO-RST (transitionary at powerdown) * Switching Time: Timing for switching from an arbitrary state to the next state. **Turn on time: Time to guarantee RF performance after switch activation. 11 Features PM_TRIG with three triggers Software reset and debug using the RFFE_STATUS register Register 0 write Full speed write, Half speed read GSID Programmable USID Initial power mode : Low power Explanation of Register Slave Address: 1001 Register Address 0x0000 0x0010 0x001A Register Name Data Bits 6:0 Antenna switch states (see Truth Table) Register 0 Write command sequence use. Trigger Support. 7:0 Antenna switch states (see Truth Table) Read/Write command sequence use. Trigger Support. 7:6 MAJOR REV 5:4 MINOR REV 3:0 MISC REV REGISTER_0 (Table A or B) REVISION_ID (Table C) RFFE_STATUS (Table D) 0x001B GROUP_ID (Table E) 0x001C PM_TRIG (Table F) Notes 7 SOFTWARE RESET 6 COMMAND_FRAME_PARITY_ERR 5 COMMAND_LENGTH_ERR 4 ADDRESS_FRAME_PARITY_ERR 3 DATA_FRAME_PARITY_ERR 2 READ_UNUSED_REG 1 WRITE_UNUSED_REG 0 BID_GID_ERR 7:4 RESERVED 3:0 GROUP_SID 7:6 Power mode 5:3 Trigger_Mask_[2:0] 2:0 Trigger_[2:0] Read Write W R/W R R/W R/W R/W 0x001D PRODUCT_ID (Table G) 7:0 PRODUCT_ID R 0x001E MANUFACTURER_ID (Table H) 7:0 MANUFACTURER_ID[7:0] R 7:6 SPARE R 0x001F SPARE MANUFACTURER_ID USID (Table I) 5:4 MANUFACTURER_ID[9:8] R 3:0 USID R/W MANUFACTURER_ID[9:0] is defined by SONY ID (0x01B0) 12 Write and Read command sequence 13 Antenna switch state command sequences 14 Register Map 15 16 17 Recommended Circuit *1: No DC blocking capacitors are required on all RF ports. (Except external DC bias) *2: DC levels of all RF ports are GND. *3: C1(100pF) is recommended. *4: C2(0.1uF) is recommended. *5: C3(22pF) is recommended. *6: L1(22nH) is recommended. 18 Recommended Land Pattern 19 Recommended PCB Design 20 Package Outline (Unit: mm) 21 Marking 22 Tape and Reel Size 23 Moisture Sensitivity Moisture Sensitivity Level for this part is MSL = 2 24 Note Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits 25