PDF Data Sheet

Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
HMC489LP5 / 489LP5E
v01.0705
SURFACE MOUNT PHEMT 1 WATT
POWER AMPLIFIER, 12 - 16 GHz
LINEAR & POWER AMPLIFIERS - SMT
11
Typical Applications
Features
The HMC489LP5 / HMC489LP5E is ideal for use as
a power amplifier for:
Saturated Power: +32 dBm @ 16% PAE
• Point-to-Point Radios
Gain: 13 dB
• Point-to-Multi-Point Radios
+7V @ 1300 mA Supply
• Test Equipment and Sensors
50 Ohm Matched Input/Output
• Military End-Use
25 mm2 Leadless SMT Package
Functional Diagram
General Description
Output IP3: +34 dBm
The HMC489LP5 & HMC489LP5E are high dynamic
range GaAs PHEMT MMIC Power Amplifiers housed
in leadless 5 x 5 mm surface mount packages.
Operating from 12 to 16 GHz, the amplifier provides
13 dB of gain, +32 dBm of saturated power and
16% PAE from a +7V supply voltage. Output IP3 is
+34 dBm typical. The RF I/Os are DC blocked
and matched to 50 Ohms for ease of use. The
HMC489LP5(E)eliminate the need for wire bonding,
allowing use of surface mount manufacturing
techniques.
Electrical Specifi cations, TA = +25° C, Vdd1, 2, 3, 4, 5 = +7V, Idd = 1300 mA*
Parameter
Min.
Frequency Range
Gain
10
Gain Variation Over Temperature
Max.
Min.
10
0.07
29
28
dB
0.07
dB/ °C
dB
15
dB
31
dBm
Saturated Output Power (Psat)
30
32
dBm
Output Third Order Intercept (IP3)
32
34
dBm
Noise Figure
Supply Current (Idd)(Vdd = +7V, Vgg = -0.3V Typ.)
7
9
dB
1300
1300
mA
* Adjust Vgg between -2 to 0V to achieve Idd = 1300 mA typical.
11 - 276
Units
GHz
8
8
24
Max.
13
0.05
12
Output Return Loss
Typ.
14 - 16
13
0.05
Input Return Loss
Output Power for 1 dB Compression (P1dB)
Typ.
12 - 14
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC489LP5 / 489LP5E
v01.0705
SURFACE MOUNT PHEMT 1 WATT
POWER AMPLIFIER, 12 - 16 GHz
Broadband Gain and Return Loss
Gain vs. Temperature
15
20
16
S21
S11
S22
12
GAIN (dB)
RESPONSE (dB)
5
-5
8
11
+25 C
+85 C
-40 C
4
-15
-25
-4
8
9
10
11
12
13
14
15
16
17
18
19
11
12
FREQUENCY (GHz)
0
-5
-5
RETURN LOSS (dB)
RETURN LOSS (dB)
15
16
17
Output Return Loss vs. Temperature
0
-10
+25 C
+85 C
-40 C
-20
-10
-15
+25 C
+85 C
-40 C
-20
-25
-25
11
12
13
14
15
16
17
11
12
FREQUENCY (GHz)
14
15
16
17
16
17
Psat vs. Temperature
34
30
30
26
26
Psat (dBm)
34
+25 C
+85 C
-40 C
22
13
FREQUENCY (GHz)
P1dB vs. Temperature
P1dB (dBm)
14
FREQUENCY (GHz)
Input Return Loss vs. Temperature
-15
13
22
18
18
14
14
10
LINEAR & POWER AMPLIFIERS - SMT
0
+25 C
+85 C
-40 C
10
11
12
13
14
15
FREQUENCY (GHz)
16
17
11
12
13
14
15
FREQUENCY (GHz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
11 - 277
HMC489LP5 / 489LP5E
v01.0705
SURFACE MOUNT PHEMT 1 WATT
POWER AMPLIFIER, 12 - 16 GHz
Output IP3 vs. Temperature
Power Compression @ 15 GHz
36
Pout (dBm), GAIN (dB), PAE (%)
40
35
+25 C
+85 C
-40 C
25
20
15
10
12
13
14
18
12
6
15
16
17
-8
-4
0
FREQUENCY (GHz)
8
12
16
20
24
Gain, Power & OIP3
vs. Supply Current @ 15 GHz
Gain
P1dB
Psat
IP3
7
7.5
Gain (dB), P1dB (dBm), Psat (dBm), IP3 (dBm)
Gain (dB), P1dB (dBm), Psat (dBm), IP3 (dBm)
36
34
32
30
28
26
24
22
20
18
16
14
12
10
6.5
4
INPUT POWER (dBm)
Gain, Power & Output IP3
vs. Supply Voltage @ 15 GHz
40
35
30
25
Gain
P1dB
Psat
IP3
20
15
10
700
800
Vdd Supply Voltage (Vdc)
900
1000
1100
1200
1300
Idd Supply Current (mA)
Reverse Isolation vs. Temperature
Noise Figure vs. Temperature
15
0
12
+25 C
+85 C
-40 C
ISOLATION (dB)
-20
9
6
-40
-60
+25 C
+85 C
-40 C
3
0
-80
11
12
13
14
15
FREQUENCY (GHz)
11 - 278
24
0
11
NOISE FIGURE (dB)
LINEAR & POWER AMPLIFIERS - SMT
11
IP3 (dBm)
30
Pout
Gain
PAE
30
16
17
11
12
13
14
15
16
FREQUENCY (GHz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
17
HMC489LP5 / 489LP5E
v01.0705
SURFACE MOUNT PHEMT 1 WATT
POWER AMPLIFIER, 12 - 16 GHz
Typical Supply Current vs. Vdd
POWER DISSIPATION (W)
10.5
Max Pdiss @ +85C
10
Vdd (Vdc)
Idd (mA)
+6.5
1330
+7.0
1300
+7.5
1285
9.5
9
Note: Amplifi er will operate over full voltage ranges shown
above. Vgg adjusted to achieve Idd= 1300 mA at +7.0V.
8.5
14 GHz
Absolute Maximum Ratings
8
7.5
7
-10 -8 -6 -4 -2 0
2
4
6
8 10 12 14 16 18 20 22 24
Drain Bias Voltage (Vdd1, 2, 3, 4, 5)
+8 Vdc
Gate Bias Voltage (Vgg)
-2.0 to 0 Vdc
RF Input Power (RFIN)(Vdd = +7.0 Vdc)
+28 dBm
Channel Temperature
150 °C
Continuous Pdiss (T= 85 °C)
(derate 154 mW/°C above 85 °C)
10 W
Thermal Resistance
(channel to ground paddle)
6.5 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-40 to +85 °C
INPUT POWER (dBm)
* Refer to “Thermal Management for Surface Mount
Components” application note herein.
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE.
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
11
LINEAR & POWER AMPLIFIERS - SMT
Power Dissipation*
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST BE
SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED
LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC489LP5
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
HMC489LP5E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
Package Marking [3]
[1]
H489
XXXX
[2]
H489
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
11 - 279
HMC489LP5 / 489LP5E
v01.0705
SURFACE MOUNT PHEMT 1 WATT
POWER AMPLIFIER, 12 - 16 GHz
Pin Descriptions
Pin Number
Function
Description
1 - 3, 5 - 8, 10 - 12,
14, 15, 17 - 20, 22 24, 26, 27, 29 - 31
N/C
No connection required. These pins may be connected to
RF/DC ground without affecting performance.
4
RFIN
This pin is AC coupled and
matched to 50 Ohms.
9
Vgg
Gate control for amplifier. Adjust to achieve Idd of 1300 mA.
Please follow “MMIC Amplifier Biasing Procedure”
Application Note. External bypass capacitors of 100 pF and
2.2 μF are required.
21
RFOUT
This pin is AC coupled and
matched to 50 Ohms.
32, 28, 25,
13, 16
Vdd1, Vdd2,
Vdd3, Vdd4,
Vdd5
Power Supply Voltage for the amplifier. External bypass
capacitors of 100 pF and 2.2 μF are required.
GND
Ground: Backside of package has exposed metal ground
slug that must be connected to ground through a short path.
Vias under the device are required
LINEAR & POWER AMPLIFIERS - SMT
11
11 - 280
Interface Schematic
Application Circuit
Component
Value
C1
100 pF
C2
2.2 μF
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC489LP5 / 489LP5E
v01.0705
SURFACE MOUNT PHEMT 1 WATT
POWER AMPLIFIER, 12 - 16 GHz
Evaluation PCB
List of Materials for Evaluation PCB 108190 [1]
Item
Description
J1, J2
SRI PC Mount SMA Connector
J3, J4
2mm DC Header
C1 - C6
100 pF capacitor, 0402 pkg.
C7 - C12
2.2μF Capacitor, Tantalum
U1
HMC489LP5 / HMC489LP5E Amplifier
PCB [2]
108188 Evaluation PCB
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350.
The circuit board used in this application should use
RF circuit design techniques. Signal lines should
have 50 ohm impedance while the package ground
leads and exposed paddle should be connected
directly to the ground plane similar to that shown.
A sufficient number of via holes should be used to
connect the top and bottom ground planes. Copper
filled vias under the device are recommended. The
evaluation board should be mounted to an appropriate heat sink. The evaluation circuit board shown is
available from Hittite upon request.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
LINEAR & POWER AMPLIFIERS - SMT
11
11 - 281