PDF Data Sheet

Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
HMC486LP5 / 486LP5E
v02.0110
LINEAR & POWER AMPLIFIERS - SMT
11
SURFACE MOUNT PHEMT 2 WATT POWER
AMPLIFIER, 7 - 9 GHz
Typical Applications
Features
The HMC486LP5(E) is ideal for:
Saturated Power: +33 dBm @ 20% PAE
• Point-to-Point Radios
Output IP3: +40 dBm
• Point-to-Multi-Point Radios
Gain: 22 dB
• Test Equipment and Sensors
Supply: +7V @ 1300 mA
• Military End-Use
50 Ohm Matched Input/Output
32 Lead 5x5mm SMT Package: 25mm2
General Description
Functional Diagram
The HMC486LP5(E) is a high dynamic range GaAs
pHEMT MMIC 2 Watt Power Amplifier housed in a
leadless 5x5 mm surface mount packages. Operating
from 7 to 9 GHz, the amplifier provides 22 dB of gain,
+33 dBm of saturated power and 20% PAE from a
+7V supply voltage. Output IP3 is +40 dBm typical.
The RF I/Os are DC blocked and matched to
50 Ohms for ease of use. The HMC486LP5(E)
eliminate the need for wire bonding, allowing use of
surface mount manufacturing techniques.
Electrical Specifi cations, TA = +25° C, Vdd1, 2, 3, 4, 5 = +7V, Idd = 1300 mA*
Parameter
Min.
Frequency Range
Gain
18
Gain Variation Over Temperature
Max.
Min.
19
0.07
32
28
dB
0.07
dB/ °C
dB
5
dB
31
dBm
Saturated Output Power (Psat)
33
32
dBm
Output Third Order Intercept (IP3)
41
38
dBm
Noise Figure
Supply Current (Idd)(Vdd = +7V, Vgg = -0.3V Typ.)
7.0
7.5
dB
1300
1300
mA
* Adjust Vgg between -2 to 0V to achieve Idd = 1300 mA typical.
11 - 256
Units
GHz
17
8
29
Max.
22
0.05
12
Output Return Loss
Typ.
8-9
21
0.05
Input Return Loss
Output Power for 1 dB Compression (P1dB)
Typ.
7-8
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC486LP5 / 486LP5E
v02.0110
SURFACE MOUNT PHEMT 2 WATT POWER
AMPLIFIER, 7 - 9 GHz
Broadband Gain and Return Loss
Gain vs. Temperature
25
30
25
S21
S11
S22
5
GAIN (dB)
-5
20
15
-15
5
-25
0
4
5
6
7
8
9
10
11
6
6.5
7
FREQUENCY (GHz)
8
8.5
9
9.5
10
Output Return Loss vs. Temperature
0
0
+25 C
+85 C
-40 C
+25 C
+85 C
-40 C
-2
RETURN LOSS (dB)
-5
RETURN LOSS (dB)
7.5
FREQUENCY (GHz)
Input Return Loss vs. Temperature
-10
-15
-20
-4
-6
-8
-25
-10
6
6.5
7
7.5
8
8.5
9
9.5
10
6
6.5
7
FREQUENCY (GHz)
8
8.5
9
9.5
9
9.5
10
Psat vs. Temperature
34
32
32
Psat (dBm)
34
30
+25 C
+85 C
-40 C
28
7.5
FREQUENCY (GHz)
P1dB vs. Temperature
P1dB (dBm)
11
+25 C
+85 C
-40 C
10
26
LINEAR & POWER AMPLIFIERS - SMT
RESPONSE (dB)
15
30
+25 C
+85 C
-40 C
28
26
24
24
6
6.5
7
7.5
8
8.5
FREQUENCY (GHz)
9
9.5
10
6
6.5
7
7.5
8
8.5
10
FREQUENCY (GHz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
11 - 257
HMC486LP5 / 486LP5E
v01.0705
SURFACE MOUNT PHEMT 2 WATT POWER
AMPLIFIER, 7 - 9 GHz
Output IP3 vs. Temperature
Power Compression @ 8 GHz
44
Pout (dBm), GAIN (dB), PAE (%)
36
36
+25 C
+85 C
-40 C
32
24
6
6.5
7
7.5
8
8.5
9
9.5
24
18
Pout
Gain
PAE
12
6
0
-10
10
-6
-2
Gain (dB), P1dB (dBm), Psat (dBm), IP3 (dBm)
42
40
38
36
34
32
Gain
P1dB
Psat
IP3
28
26
24
22
20
6.5
6
10
14
18
Gain, Power & OIP3
vs. Supply Current @ 8 GHz
Gain, Power & OIP3
vs. Supply Voltage @ 8 GHz
30
2
INPUT POWER (dBm)
7
7.5
42
40
38
36
34
32
30
28
Gain
P1dB
Psat
IP3
26
24
22
20
700
800
900
Vdd Supply Voltage (Vdc)
1000
1100
1200
1300
Idd Supply Current (mA)
Reverse Isolation vs. Temperature
Noise Figure vs. Temperature
14
0
12
-10
+25 C
+85 C
-40 C
ISOLATION (dB)
10
8
6
4
-20
-30
+25 C
+85 C
-40
-40 C
-50
2
-60
0
-70
6
6.5
7
7.5
8
8.5
FREQUENCY (GHz)
11 - 258
30
FREQUENCY (GHz)
NOISE FIGURE (dB)
LINEAR & POWER AMPLIFIERS - SMT
28
Gain (dB), P1dB (dBm), Psat (dBm), IP3 (dBm)
11
IP3 (dBm)
40
9
9.5
10
6
6.5
7
7.5
8
8.5
9
FREQUENCY (GHz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
9.5
10
HMC486LP5 / 486LP5E
v01.0705
SURFACE MOUNT PHEMT 2 WATT POWER
AMPLIFIER, 7 - 9 GHz
Typical Supply Current vs. Vdd
Power Dissipation*
Max Pdiss @ +85C
10
Vdd (V)
Idd (mA)
+6.5
1330
+7.0
1300
+7.5
1285
9.5
9
Note: Amplifi er will operate over full voltage ranges shown
above. Vgg adjusted to achieve Idd= 1300 mA at +7V.
8.5
8 GHz
7.5
7
-10
11
Absolute Maximum Ratings
8
-6
-2
2
6
10
14
18
INPUT POWER (dBm)
* Please refer to “Thermal Management for Surface Mount
Components” application note at www.hittite.com/
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Drain Bias Voltage (Vdd1, 2, 3, 4, 5)
+8V
Gate Bias Voltage (Vgg)
-2 to 0V
RF Input Power (RFIN)(Vdd = +7V)
+20 dBm
Channel Temperature
150 °C
Continuous Pdiss (T = 85 °C)
(derate 154 mW/°C above 85 °C)
10 W
Thermal Resistance
(channel to ground paddle)
6.5 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-40 to +85 °C
Outline Drawing
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE.
LINEAR & POWER AMPLIFIERS - SMT
POWER DISSIPATION (W)
10.5
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC486LP5
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
HMC486LP5E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
Package Marking [3]
[1]
H486
XXXX
[2]
H486
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
11 - 259
HMC486LP5 / 486LP5E
v01.0705
SURFACE MOUNT PHEMT 2 WATT POWER
AMPLIFIER, 7 - 9 GHz
Pin Descriptions
Pin Number
Function
Description
1-3, 5-8, 10-12, 14,
15, 17-20, 22-24,
26, 27, 29-31
N/C
No connection required. These pins may be connected to
RF/DC ground without affecting performance.
4
RFIN
This pin is AC coupled
and matched to 50 Ohms.
9
Vgg
Gate control for amplifier. Adjust to achieve Idd of 1300
mA. Please follow “MMIC Amplifier Biasing Procedure”
Application Note. External bypass capacitors of 100 pF
and 2.2 μF are required.
21
RFOUT
This pin is AC coupled
and matched to 50 Ohms.
32, 28, 25,
13, 16
Vdd1, Vdd2,
Vdd3, Vdd4,
Vdd5
Power Supply Voltage for the amplifier. External bypass
capacitors of 100 pF and 2.2 μF are required.
Package Bottom
GND
Ground: Backside of package has exposed metal ground
slug that must be connected to ground through a short
path. Vias under the device are required
LINEAR & POWER AMPLIFIERS - SMT
11
11 - 260
Interface Schematic
Application Circuit
Component
Value
C1
100 pF
C2
2.2 μF
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC486LP5 / 486LP5E
v01.0705
SURFACE MOUNT PHEMT 2 WATT POWER
AMPLIFIER, 7 - 9 GHz
Evaluation PCB
List of Materials for Evaluation PCB 108190 [1]
Item
Description
J1, J2
SRI PC Mount SMA Connector
J3, J4
2mm DC Header
C1 - C6
100 pF Capacitor, 0402 Pkg.
C7 - C12
2.2μF Capacitor, Tantalum
U1
HMC486LP5(E) Amplifier
PCB [2]
108188 Evaluation PCB
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350.
The circuit board used in this application should use
RF circuit design techniques. Signal lines should
have 50 Ohm impedance while the package ground
leads and exposed paddle should be connected
directly to the ground plane similar to that shown.
A sufficient number of via holes should be used to
connect the top and bottom ground planes. Copper
filled vias under the device are recommended. The
evaluation board should be mounted to an appropriate heat sink. The evaluation circuit board shown is
available from Hittite upon request.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
LINEAR & POWER AMPLIFIERS - SMT
11
11 - 261