Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK HMC487LP5 / 487LP5E v01.0705 LINEAR & POWER AMPLIFIERS - SMT 11 SURFACE MOUNT PHEMT 2 WATT POWER AMPLIFIER, 9 - 12 GHz Typical Applications Features The HMC487LP5 / HMC487LP5E is ideal for use as a power amplifier for: Saturated Power: +33 dBm @ 20% PAE • Point-to-Point Radios Gain: 20 dB • Point-to-Multi-Point Radios +7V @ 1300 mA Supply • Test Equipment and Sensors 50 Ohm Matched Input/Output • Military End-Use 25 mm2 Leadless SMT Package Functional Diagram General Description Output IP3: +36 dBm The HMC487LP5 & HMC487LP5E are high dynamic range GaAs PHEMT MMIC 2 Watt Power Amplifiers housed in leadless 5 x 5 mm surface mount packages. Operating from 9 to 12 GHz, the amplifier provides 20 dB of gain, +33 dBm of saturated power and 20% PAE from a +7V supply voltage. Output IP3 is +36 dBm typical. The RF I/Os are DC blocked and matched to 50 Ohms for ease of use. The HMC487LP5(E) eliminate the need for wire bonding, allowing use of surface mount manufacturing techniques. Electrical Specifi cations, TA = +25° C, Vdd1, 2, 3, 4, 5 = +7V, Idd = 1300 mA* Parameter Min. Frequency Range Gain 17 Gain Variation Over Temperature Max. Min. 19 0.07 32 28 dB 0.07 dB/ °C dB 15 dB 31 dBm Saturated Output Power (Psat) 33 32 dBm Output Third Order Intercept (IP3) 36 35 dBm Noise Figure Supply Current (Idd)(Vdd = +7V, Vgg = -0.3V Typ.) 9 8 dB 1300 1300 mA * Adjust Vgg between -2 to 0V to achieve Idd = 1300 mA typical. 11 - 270 Units GHz 15 7 29 Max. 22 0.05 7 Output Return Loss Typ. 11 - 12 20 0.05 Input Return Loss Output Power for 1 dB Compression (P1dB) Typ. 9 - 11 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC487LP5 / 487LP5E v01.0705 SURFACE MOUNT PHEMT 2 WATT POWER AMPLIFIER, 9 - 12 GHz Broadband Gain and Return Loss Gain vs. Temperature 25 30 25 20 S21 S11 S22 5 GAIN (dB) -5 15 -15 11 +25 C +85 C -40 C 10 5 -25 0 6 7 8 9 10 11 12 13 14 15 8 9 FREQUENCY (GHz) 10 11 12 13 FREQUENCY (GHz) Input Return Loss vs. Temperature Output Return Loss vs. Temperature 0 0 RETURN LOSS (dB) RETURN LOSS (dB) -5 -10 -15 +25 C +85 C -40 C -20 -25 -5 -10 +25 C +85 C -40 C -15 -20 8 9 10 11 12 8 13 9 FREQUENCY (GHz) 11 12 13 12 13 Psat vs. Temperature 36 36 34 34 32 32 Psat (dBm) P1dB (dBm) P1dB vs. Temperature 30 +25 C +85 C -40 C 28 10 FREQUENCY (GHz) 30 +25 C +85 C -40 C 28 26 LINEAR & POWER AMPLIFIERS - SMT RESPONSE (dB) 15 26 24 24 8 9 10 11 FREQUENCY (GHz) 12 13 8 9 10 11 FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 11 - 271 HMC487LP5 / 487LP5E v01.0705 SURFACE MOUNT PHEMT 2 WATT POWER AMPLIFIER, 9 - 12 GHz Output IP3 vs. Temperature Power Compression @ 10.5 GHz 36 Pout (dBm), GAIN (dB), PAE (%) 42 38 30 26 22 +25 C +85 C -40 C 18 10 8 9 10 11 12 24 18 Pout Gain PAE 12 6 0 -10 13 -6 -2 Gain (dB), P1dB (dBm), Psat (dBm), IP3 (dBm) 38 36 34 32 30 Gain P1dB Psat IP3 26 24 22 20 18 6.5 6 10 14 18 Gain, Power and OIP3 vs. Supply Current @ 10.5 GHz 40 28 2 INPUT POWER (dBm) Gain Power and OIP3 vs. Supply Voltage @10.5 GHz 7 7.5 42 38 34 30 Gain P1dB Psat IP3 26 22 18 800 900 Vdd Supply Voltage (Vdc) 1000 1100 1200 1300 Idd Supply Current (mA) Noise Figure vs. Temperature Reverse Isolation vs. Temperature 0 15 -10 ISOLATION (dB) 12 9 6 -20 -30 +25 C +85 C -40 C -40 -50 +25 C +85 C -40 C 3 -60 0 -70 8 9 10 11 FREQUENCY (GHz) 11 - 272 30 FREQUENCY (GHz) NOISE FIGURE (dB) LINEAR & POWER AMPLIFIERS - SMT 14 Gain (dB), P1dB (dBm), Psat (dBm), IP3 (dBm) 11 IP3 (dBm) 34 12 13 8 9 10 11 12 FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 13 HMC487LP5 / 487LP5E v01.0705 SURFACE MOUNT PHEMT 2 WATT POWER AMPLIFIER, 9 - 12 GHz Typical Supply Current vs. Vdd Power Dissipation* Max Pdiss @ +85C 10 Vdd (Vdc) Idd (mA) +6.5 1330 +7.0 1300 +7.5 1285 9 8 Note: Amplifi er will operate over full voltage ranges shown above. Vgg adjusted to achieve Idd= 1300 mA at +7.0V. 11 GHz 11 Absolute Maximum Ratings 7 6 5 -10 -8 -6 -4 -2 0 2 4 6 8 10 12 14 16 INPUT POWER (dBm) * Refer to “Thermal Management for Surface Mount Components” application note herein. ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Drain Bias Voltage (Vdd1, 2, 3, 4, 5) +8 Vdc Gate Bias Voltage (Vgg) -2.0 to 0 Vdc RF Input Power (RFIN)(Vdd = +7.0 Vdc) +20 dBm Channel Temperature 150 °C Continuous Pdiss (T= 85 °C) (derate 154 mW/°C above 85 °C) 10 W Thermal Resistance (channel to ground paddle) 6.5 °C/W Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. LINEAR & POWER AMPLIFIERS - SMT POWER DISSIPATION (W) 11 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC487LP5 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 HMC487LP5E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 Package Marking [3] [1] H487 XXXX [2] H487 XXXX [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 11 - 273 HMC487LP5 / 487LP5E v01.0705 SURFACE MOUNT PHEMT 2 WATT POWER AMPLIFIER, 9 - 12 GHz Pin Descriptions Pin Number Function Description 1 - 3, 5 - 8, 10 - 12, 14, 15, 17 - 20, 22 24, 26, 27, 29 - 31 N/C No connection required. These pins may be connected to RF/DC ground without affecting performance. 4 RFIN This pin is AC coupled and matched to 50 Ohms. 9 Vgg Gate control for amplifier. Adjust to achieve Idd of 1300 mA. Please follow “MMIC Amplifier Biasing Procedure” Application Note. External bypass capacitors of 100 pF and 2.2 μF are required. 21 RFOUT This pin is AC coupled and matched to 50 Ohms. 32, 28, 25, 13, 16 Vdd1, Vdd2, Vdd3, Vdd4, Vdd5 Power Supply Voltage for the amplifier. External bypass capacitors of 100 pF and 2.2 μF are required. GND Ground: Backside of package has exposed metal ground slug that must be connected to ground through a short path. Vias under the device are required LINEAR & POWER AMPLIFIERS - SMT 11 11 - 274 Interface Schematic Application Circuit Component Value C1 100 pF C2 2.2 μF For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC487LP5 / 487LP5E v01.0705 SURFACE MOUNT PHEMT 2 WATT POWER AMPLIFIER, 9 - 12 GHz Evaluation PCB List of Materials for Evaluation PCB 108190 [1] Item Description J1, J2 SRI PC Mount SMA Connector J3, J4 2mm DC Header C1 - C6 100 pF capacitor, 0402 pkg. C7 - C12 2.2μF Capacitor, Tantalum U1 HMC487LP5 / HMC487LP5E Amplifier PCB [2] 108188 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350. The circuit board used in this application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. Copper filled vias under the device are recommended. The evaluation board should be mounted to an appropriate heat sink. The evaluation circuit board shown is available from Hittite upon request. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com LINEAR & POWER AMPLIFIERS - SMT 11 11 - 275