TE Analog Devices Welcomes Hittite Microwave Corporation O B SO LE NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com TE O B SO LE THIS PAGE INTENTIONALLY LEFT BLANK HMC203 v03.1007 GaAs MMIC DOUBLE-BALANCED MIXER, 14 - 23 GHz Typical Applications Features The HMC203 is ideal for: Conversion Loss: 10 dB • DBS & SATCOM LO / RF Isolation: 38 dB • Microwave Radio Passive: No DC Bias Required • Military & Space Die Size: 1.49 x 0.89 x 0.1 mm • Radar & EW 4 - 32 TE • Test Equipment & Sensors Functional Diagram General Description B SO LE The HMC203 chip is a miniature double-balanced mixer which can be used as an upconverter or downconverter. Excellent isolations are provided by on-chip baluns, which require no external components and no DC bias. The mixer chip can be integrated directly into MMIC hybrid applications. Unless otherwise stated, all data was measured with the mixer mounted in a MMIC test fixture. The MMIC was connected to thin film 50 ohm transmission lines with 1 mil diameter wirebonds of <10 mils in length. Electrical Specifi cations, TA = +25° C, LO Drive = +15 dBm O MIXERS - DOUBLE-BALANCED - CHIP 4 Parameter Min. Typ. Frequency Range, RF & LO 14 - 23 Frequency Range, IF DC - 2 Max. Min. Typ. Max. 15 - 21 Units GHz DC -2 GHz Conversion Loss 10 12 8.5 10 dB Noise Figure (SSB) 10 12 8.5 10 dB LO to RF Isolation 30 38 30 38 dB LO to IF Isolation 35 45 35 45 dB RF to IF Isolation 12 17 12 17 dB IP3 (Input) 18 18 dBm IP2 (Input) 40 40 dBm 1 dB Gain Compression (Input) 7 7 dBm For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC203 v03.1007 GaAs MMIC DOUBLE-BALANCED MIXER, 14 - 23 GHz Conversion Loss vs LO Drive Isolation, LO = +15 dBm 0 -10 +8 dBm +10 dBm +12 dBm +15 dBm -20 -30 -40 -60 -70 13 15 17 19 21 23 25 13 15 17 19 21 23 25 FREQUENCY (GHz) LE FREQUENCY (GHz) Conversion Loss @ +85 C vs. LO Drive IF Bandwidth LO = 18 GHz @ +15 dBm 0 0 -10 B SO -5 +8 dBm +10 dBm +12 dBm +15 dBm -15 -20 13 15 17 19 21 23 -5 -10 -15 +8 dBm +10 dBm +12 dBm +15 dBm -20 -25 0 25 2 -5 -10 +8 dBm +10 dBm +12 dBm +15 dBm -20 13 15 17 19 21 FREQUENCY (GHz) 23 25 CONVERSION LOSS AND ISOLATION (dB) 0 -15 6 RF Coplanar Probe Data LO = +12 dBm O Conversion Loss @ -55 C vs LO Drive 4 IF FREQUENCY (GHz) FREQUENCY (GHz) CONVERSION LOSS (dB) 4 -50 TE -15 LO/RF 0 CONVERSION LOSS -10 -20 MIXERS - DOUBLE-BALANCED - CHIP ISOLATION (dB) -5 -20 CONVERSION LOSS (dB) RF/IF LO/IF -10 CONVERSION LOSS (dB) CONVERSION LOSS (dB) 0 RF/IF ISO -30 LO/RF ISO -40 -50 LO/IF ISO -60 10 15 20 25 30 35 40 FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 4 - 33 HMC203 v03.1007 GaAs MMIC DOUBLE-BALANCED MIXER, 14 - 23 GHz Absolute Maximum Ratings RF / IF Input +13 dBm LO Drive +27 dBm Storage Temperature -65 to +150 °C Operating Temperature -55 to +85 °C ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS 4 - 34 TE B SO LE Outline Drawing Die Packaging Information [1] Standard O MIXERS - DOUBLE-BALANCED - CHIP 4 WP-8 (Waffle Pack) Alternate [2] [1] Refer to the “Packaging Information” section for die packaging dimensions. [2] For alternate packaging information contact Hittite Microwave Corporation. NOTES: 1. ALL DIMENSIONS ARE IN INCHES [MM]. 2. DIE THICKNESS IS .004”. 3. BOND PADS ARE .004” SQUARE. 4. BOND PAD SPACING CENTER TO CENTER IS .006”. 5. BACKSIDE METALLIZATION: GOLD. 6. BOND PAD METALLIZATION: GOLD. 7. BACKSIDE METAL IS GROUND. 8. CONNECTION NOT REQUIRED FOR UNLABELED BOND PADS. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC203 v03.1007 GaAs MMIC DOUBLE-BALANCED MIXER, 14 - 23 GHz Pad Descriptions Description 1 RF This pin is AC coupled and matched to 50 Ohms. 2 LO This pin is AC coupled and matched to 50 Ohms. 3 IF This pin is DC coupled. For applications not requiring operation to DC, this port should be DC blocked externally using a series capacitor whose value has been chosen to pass the necessary IF frequency range. For operation to DC, this pin must not source/sink more than 2 mA of current or die non-function and possible die failure will result. Die Bottom GND Die bottom must be connected to RF/DC ground. LE Handling Precautions Interface Schematic B SO Follow these precautions to avoid permanent damage. Storage: All bare die are placed in either Waffle or Gel based ESD protective containers, and then sealed in an ESD protective bag for shipment. Once the sealed ESD protective bag has been opened, all die should be stored in a dry nitrogen environment. Cleanliness: Handle the chips in a clean environment. DO NOT attempt to clean the chip using liquid cleaning systems. Static Sensitivity: Follow ESD precautions to protect against ESD strikes. Transients: Suppress instrument and bias supply transients while bias is applied. Use shielded signal and bias cables to minimize inductive pick-up. General Handling: Handle the chip along the edges with a vacuum collet or with a sharp pair of bent tweezers. The surface of the chip has fragile air bridges and should not be touched with vacuum collet, tweezers, or fingers. Mounting O The chip is back-metallized and can be die mounted with AuSn eutectic preforms or with electrically conductive epoxy. The mounting surface should be clean and flat. Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work surface temperature of 255 °C and a tool temperature of 265 °C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 °C. DO NOT expose the chip to a temperature greater than 320 °C for more than 20 seconds. No more than 3 seconds of scrubbing should be required for attachment. Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule. 4 MIXERS - DOUBLE-BALANCED - CHIP Function TE Pad Number Wire Bonding RF bonds made with 0.003” x 0.0005” ribbon are recommended. These bonds should be thermosonically bonded with a force of 40-60 grams. DC bonds of 0.001” (0.025 mm) diameter, thermosonically bonded, are recommended. Ball bonds should be made with a force of 40-50 grams and wedge bonds at 18-22 grams. All bonds should be made with a nominal stage temperature of 150 °C. A minimum amount of ultrasonic energy should be applied to achieve reliable bonds. All bonds should be as short as possible, less than 12 mils (0.31 mm). For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 4 - 35