CL330 3-Channel 30mA Linear LED Driver Features General Description ► ±6.0% current accuracy @ 4.0 -15V ► 90V standoff voltage ► Separate enable pins for each channel allow for PWM dimming ► Over-temperature protection ► 8-Lead SOIC (w/Heat Slug) package The CL330 is designed to drive 3 strings of LEDs at a constant current of 30mA. Other drivers with currents in the range of 20 - 30mA are available. The drive current is fixed, with a ±6% tolerance over a VOUT range of 4.0 - 15V. Separate enable pins for each channel allow for PWM dimming, 3-step linear dimming, or individual disconnection of faulty LED strings. Applications ► LCD backlighting ► Indicator lamps Over-temperature protection circuitry shuts down all 3 channels when the nominal die temperature reaches 135°C. Normal operation resumes when the die temperature drops by 30°C. The CL330 is available in the 8-Lead SOIC (w/Heat Slug) package and requires a single ceramic bypass capacitor which may be shared among several drivers. Block Diagram and Typical Application Circuit 6.5 - 90V CIN 100nF 8 7 6 5 VIN OUT1 OUT2 OUT3 REG Host Controller 1 EN1 2 EN2 3 EN3 VDD GND CL330 4 ● 1235 Bordeaux Drive, Sunnyvale, CA 94089 ● Tel: 408-222-8888 ● www.supertex.com CL330 Ordering Information 8-Lead SOIC (w/Heat Slug) Device 4.90x3.90mm body 1.70mm height (max) 1.27mm pitch CL330 CL330SG-G -G indicates package is RoHS compliant (‘Green’) Pin Configuration Absolute Maximum Ratings Parameter OUT3 OUT2 OUT1 VIN Value Supply voltage, VIN -0.5V to +100V Output voltage, VOUT -0.5V to +100V Enable voltage, VEN -0.5V to +6.5V Operating temperature1 -40°C Storage temperature Underside plate is ground -65°C to +150°C EN1 Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied. Continuous operation of the device at the absolute rating level may affect device reliability. All voltages are referenced to device ground. EN2 EN3 GND 8-Lead SOIC (w/Heat Slug) (SG) Product Marking Note: 1. Maximum junction temperature internally limited. YY = Year Sealed WW = Week Sealed L = Lot Number = “Green” Packaging YYWW CL330 LLLL 8-Lead SOIC (w/Heat Slug) (SG) Recommended Operating Conditions (all voltages with respect to GND pin) Sym Parameter Min Typ Max Units VIN Supply voltage 6.5 - 90 V --- VOUT Output voltage 4.0 - 15 V EN = 0 90 V EN = 1 0 - 100 kHz --- -40 - 119 C --- - 100 - nF --- Min Typ Max - 48 - 120 135 150 O - 30 - O fEN Enable toggling frequency TJ Junction temperature CIN VIN capacitor o Conditions Thermal Characteristics Sym Parameter θJA Thermal resistance, junction to ambient TLIM Over-temperature limit THYS Over-temperature hysteresis Units Conditions C/W Mounted on JEDEC test PCB (2s 2p) O C --- C --- ● 1235 Bordeaux Drive, Sunnyvale, CA 94089 ● Tel: 408-222-8888 ● www.supertex.com 2 CL330 Electrical Characteristics (Over recommended operating conditions. TA @ 25OC unless otherwise specified.) Sym Parameter IIN VIN supply current IOUT(OFF) Output current, off IOUT(ON) Output current, on Min Typ Max Units Conditions - 220 250 µA EN1-3 = 1 - 2.2 2.3 mA EN1-3 = 0 - 4.0 10 µA ENX = 1 - - 31.8 28.2 30.0 31.8 27.0 30.0 33.0 ENX = 0, VOUT = 0 - 4.0V mA ENX = 0, VOUT = 4.0 - 15V ENX = 0, VOUT = 15 - 90V VEN(ON) Enable voltage, on - - 0.8 V --- VEN(OFF) Enable voltage, off 2.4 - - V --- CEN Enable input capacitance - 5.0 10 pF --- IENL Enable low input current - - 1.0 µA VEN = 0V IENH Enable high input current - - 1.0 µA VEN = 5.0V tON Enable on delay - 2.0 2.4 µs --- tRISE Output current rise time - 1.0 1.2 µs --- tOFF Enable off delay - 440 800 ns --- tFALL Output current fall time - 170 250 ns --- Timing EN VEN(OFF) VEN(ON) tON tOFF tRISE tFALL 90% IOUT(ON) IOUT 10% IOUT(ON) Current (Normalized to 25°C) Temperature Effects 1.05 1.00 0.95 0.90 0.85 0.80 -50 -40 0 25 50 100 120 150 Junction Temperature (°C) ● 1235 Bordeaux Drive, Sunnyvale, CA 94089 ● Tel: 408-222-8888 ● www.supertex.com 3 CL330 IOUT (normalized to nominal) Load Regulation 1.20 1.00 0.80 0.60 0.40 0.20 0 scale change 0 5 10 15 20 40 60 80 100 VOUT (V) Recommended PCB Layout 1cm2 exposed copper Underside plate soldered to copper area Exposed copper area may be plated 1cm2 exposed copper Higher LED Current VLL CIN 100nF 8 VIN REG Host Controller 1 EN1 2 EN2 3 EN3 7 6 5 OUT1 OUT2 OUT3 VDD GND CL330 4 By paralleling outputs, higher LED currents can be achieved. In addition, linear dimming in 3 discrete steps may be obtained by enabling 1, 2, or 3 outputs. ● 1235 Bordeaux Drive, Sunnyvale, CA 94089 ● Tel: 408-222-8888 ● www.supertex.com 4 CL330 Lowering CL330 Power Dissipation: Separate VIN Supply VLL VIN CIN 100nF 8 7 6 5 VIN OUT1 OUT2 OUT3 REG Host Controller 1 EN1 2 EN2 3 EN3 VDD GND 4 CL330 CL330 power dissipation may be lowered by supplying the CL330 from a voltage source (VIN) that is lower in voltage than the LED supply (VLL). Lowering CL330 Power Dissipation: Dropping Resistor VLL RDROP CIN 100nF 8 7 6 5 VIN OUT1 OUT2 OUT3 REG Host Controller 1 EN1 2 EN2 3 EN3 RDROP < VLL(MIN) - 6.5V 2.3mA where: RDROP = Dropping resistance VLL(MIN) = minimum supply voltage VDD GND CL330 4 ● 1235 Bordeaux Drive, Sunnyvale, CA 94089 ● Tel: 408-222-8888 ● www.supertex.com 5 CL330 Lowering CL330 Power Dissipation: Zener Diode VLL ZDROP CIN 100nF 8 7 6 5 VIN OUT1 OUT2 OUT3 REG Host Controller 1 EN1 2 EN2 3 EN3 VDD VZ < (VLL(MIN) - 6.5V) where: VZ = Zener Voltage VLL(MIN) = minimum supply voltage GND CL330 4 Pin Description Pin # Name Description 1 EN1 2 EN2 3 EN3 4 GND 5 OUT3 6 OUT2 7 OUT1 8 VIN Supply voltage. 6.5 to 90V. Bypass locally with a 100nF capacitor to ground. Underside Plate GND The exposed underside plate is internally connected to the GND pin. The plate may either be left floating or connected to ground. Solder the plate to an exposed copper area on the PCB for heatsinking purposes (see recommended layout). Output enable, active low. Circuit common. Constant current output (sinking). Connect the cathodes of the LEDs to these pins. ● 1235 Bordeaux Drive, Sunnyvale, CA 94089 ● Tel: 408-222-8888 ● www.supertex.com 6 CL330 8-Lead SOIC (Narrow Body w/Heat Slug) Package Outline (SG) 4.90x3.90mm body, 1.70mm height (max), 1.27mm pitch D1 D 8 8 Exposed Thermal Pad Zone E2 E E1 Note 1 (Index Area D/2 x E1/2) 1 1 Top View Bottom View A θ1 View B h h A A2 Note 1 Seating Plane e A1 b L1 A Side View View A - A L L2 Gauge Plane θ Seating Plane View B Notes: 1. A Pin 1 identifier must be located in the index area indicated. The Pin 1 identifier can be: a molded mark/identifier; an embedded metal marker; or a printed indicator. Symbol MIN Dimension NOM (mm) MAX A A1 A2 b 1.25* 0.00 1.25 0.31 - - - - 1.70 0.15 1.55* 0.51 D D1 E E1 E2 e 4.80* 3.30† 5.80* 3.80* 2.29† 4.90 - 5.00* 3.81 6.00 † 3.90 - 6.20* 4.00* 2.79 † 1.27 BSC h L 0.25 0.40 - - 0.50 1.27 L1 1.04 REF L2 0.25 BSC θ θ1 0O 5O - - 8 15O O JEDEC Registration MS-012, Variation BA, Issue E, Sept. 2005. * This dimension is not specified in the original JEDEC drawing. The value listed is for reference only. † This dimension is a non-JEDEC dimension. Drawings not to scale. Supertex Doc. #: DSPD-8SOSG, Version C090408. (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to http://www.supertex.com/packaging.html.) Supertex inc. does not recommend the use of its products in life support applications, and will not knowingly sell them for use in such applications unless it receives an adequate “product liability indemnification insurance agreement.” Supertex inc. does not assume responsibility for use of devices described, and limits its liability to the replacement of the devices determined defective due to workmanship. No responsibility is assumed for possible omissions and inaccuracies. Circuitry and specifications are subject to change without notice. For the latest product specifications refer to the Supertex inc. website: http//www.supertex.com. ©2008 Doc.# DSFP-CL330 A091508 All rights reserved. Unauthorized use or reproduction is prohibited. 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 7