DB101S-107S(DB-S)2015.08_B 02

ϭϬϭ^
THRU
ϭϬϳ^
^/E'>ͲW,^'>^^W^^/sd^hZ&DKhEdZ/'Zd/&/Z
PRIMARY CHARACTERISTICS
DB-S
VRRM
50V,100V,200V,400V
600V,800V,1000V
IO
1.0A
I2t
6.6A2S
VF
1.1V
TJ,Max
150℃
PACKAGE
Marking Code :
DB101S~DB107S
Ex :DB104S
1
2
3
4
DB104S
FEATURES
MECHANICAL DATA
Plastic material has Underwriters

Case:Molded plastic,DB-S
Laboratory

Polarity:Shown above

Flammability Classification 94V-0

Terminals :Plated terminals,

High surge overload rating of 50
solderable per MIL-STD-750,Method
Amperes peak
2026


Ideal for printed circuit board

Glass passivated chip junction

Moisture Sensitivity Level 1

Epoxy : UL94-V0 rated flame
retardant
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25 o C ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
MAXIMUM RATINGS (At TA = 25℃ unless otherwise noted)
RATINGS
SYMBOL
Marking Code
DB101S
DB102S
DB103S
DB104S
DB105S
DB106S
DB107S
DB101S
DB102S
DB103S
DB104S
DB105S
DB106S
DB107S
UNITS
Maximum Recurrent Peak Reverse Voltage
VRRM
50
100
200
400
600
800
1000
Maximum RMS Bridge Input Voltage
VRMS
35
70
140
280
420
560
700
Volts
Maximum DC Blocking Voltage
VDC
50
100
200
400
600
800
1000
Volts
Maximum Average Forward Output Current at TA = 40℃
Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on
rated load (JEDEC method)
Rating for fusing (t<8.3ms)
Typical Thermal Resistance (Note 2)
Typical Junction Capacitance (Note 1)
Operating and Storage Temperature Range
Volts
IO
1
Amps
IFSM
40
Amps
I2 t
6.6
A2 S
R θ JA
40
R θ JL
15
CJ
25
pF
TJ,TSTG
-55 to + 150
℃
℃/W
ELECTRICAL CHARACTERISTICS (At TA = 25℃ unless otherwise noted)
CHARACTERISTICS
SYMBOL
Element at 1.0A DC Maximum Forward Voltage Drop per Bridge
Maximum Reverse Current at rated
@TA = 25℃
DC Blocking Voltage per element
@TA = 125℃
DB101S
DB102S
VF
IR
DB103S
DB104S
1.1
DB105S
DB106S
DB107S
UNITS
Volts
5
uAmps
0.5
mAmps
NOTE: 1.Measured at 1 MHZ and applied reverse voltage of 4.0 VDC
2.Units mounted on P.C.B.with 0.5x0.5” (13x13mm) copper pads.
2015.0ϴ
www.willas.com.tw
Rev.0Ϯ
P1
^/E'>ͲW,^'>^^W^^/sd^hZ&DKhEdZ/'Zd/&/Z
ϭϬϭ^
THRU
ϭϬϳ^
RATINGS AND CHARACTERISTIC CURVES
2015.0ϴ
www.willas.com.tw
Rev.0Ϯ
P2
ϭϬϭ^
THRU
ϭϬϳ^
^/E'>ͲW,^'>^^W^^/sd^hZ&DKhEdZ/'Zd/&/Z
Outline Drawing
DB-S
.310(7.90)
.290(7.40)
.255(6.50)
.245(6.22)
.009
(0.23)
.049(1.25)
.038(0.95)
.060(1.52)
.040(1.02)
.013(0.33)
.003(0.08)
.410(10.4)
.360(9.40)
.346(8.80)
.307(7.80)
.135(3.40)
.102(2.60)
.205(5.2)
.195(5.0)
Dimensions in inches and (millimeters)
2015.0ϴ
www.willas.com.tw
Rev.C
Rev.0Ϯ
P3
^/E'>ͲW,^'>^^W^^/sd^hZ&DKhEdZ/'Zd/&/Z
ϭϬϭ^
THRU
ϭϬϳ^
DB-S
Suggested Soldering Pad Layout
.404(10.26)Max.
.137(3.48)Min.
.047(1.20)Min.
.060(1.52)Min.
Dimensions in inches and (millimeters)
2015.0ϴ
www.willas.com.tw
RevA
Rev.0Ϯ
P4
^/E'>ͲW,^'>^^W^^/sd^hZ&DKhEdZ/'Zd/&/Z
ϭϬϭ^
THRU
ϭϬϳ^
Ordering Information: Device PN Part Number ‐T(1)G(2)‐WS Note: (1) Packing code, Tape & Reel Packing Tape&Reel: 1 Kpcs/Reel (2) RoHS product for packing code suffix ”G”;Halogen free product for packing code suffix “H” ***Disclaimer*** WILLAS reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. WILLAS or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on WILLAS data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. WILLAS does not assume any liability arising out of the application or use of any product or circuit. WILLAS products are not designed, intended or authorized for use in medical, life‐saving implant or other applications intended for life‐sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of WILLAS. Customers using or selling WILLAS components for use in such applications do so at their own risk and shall agree to fully indemnify WILLAS Inc and its subsidiaries harmless against all claims, damages and expenditures. 2015.0ϴ
www.willas.com.tw
Rev.0Ϯ
P5