RT9178

RT9178
200mA, Ultra-Low Noise, Ultra-Fast CMOS LDO Regulator
General Description
The RT9178 is designed for portable RF and wireless
applications with demanding performance and space
requirements.
The RT9178’ s performance is optimized for batterypowered systems to deliver ultra low noise and low
quiescent current. A noise bypass pin is also available for
further reduction of output noise. Regulator ground current
increases only slightly in dropout, further prolonging the
battery life. The RT9178 also works with low-ESR ceramic
capacitors, reducing the amount of board space necessary
for power applications, critical in hand-held wireless
devices.
The RT9178 consumes less than 0.01uA in shutdown mode
and has fast turn-on time less than 100us. The other
features include ultra low dropout voltage, high output
accuracy, current limiting protection, and high ripple
rejection ratio. Available in the SOT-23-5 package.
Ordering Information
RT9178Package Type
B : SOT-23-5
BR : SOT-23-5 (R-Type)
Note :
RoHS compliant and compatible with the current requirements of IPC/JEDEC J-STD-020.
`
Ultra-Low-Noise for RF Application
Ultra-Fast Response in Line/Load Transient
Quick Start-Up (Typically 100us)
< 0.01uA Quiescent Current When Shutdown
Low Dropout : 200mV at 200mA
Wide Operating Voltage Ranges : 2.5V to 6V
TTL-Logic-Controlled Shutdown Input
Low Temperature Coefficient
Current Limiting Protection
Thermal Shutdown Protection
Only 1uF Output Capacitor Required for Stability
High Power Supply Rejection Ratio
Custom Voltage Available
RoHS Compliant and 100% Lead (Pb)-Free
Applications
CDMA/GSM Cellular Handsets
Battery-Powered Equipment
Laptop, Palmtops, Notebook Computers
Hand-Held Instruments
PCMCIA Cards
Portable Information Appliances
Marking Information
For marking information, contact our sales representative
Lead Plating System
P : Pb Free
directly or through a Richtek distributor located in your
G : Green (Halogen Free and Pb Free) area.
Output Voltage
24 : 2.4V
Pin Configurations
25 : 2.5V
:
(TOP VIEW)
31 : 3.1V
32 : 3.2V
BP
EN
VOUT
BP
2H : 2.85V
Richtek products are :
`
Features
Suitable for use in SnPb or Pb-free soldering processes.
5
4
2
3
VIN GND EN
SOT-23-5
5
4
2
3
VOUT GND VIN
R-Type
SOT-23-5
DS9178-18 April 2011
www.richtek.com
1
RT9178
Typical Application Circuit
RT9178
Chip Enable
VIN
VOUT
GND
EN
BP
+
CIN
1uF
+
VIN
COUT
2.2uF
VOUT
CBP
10nF
Functional Pin Description
Pin No.
Pin Name
Pin Function
SOT-23-5
SOT-23-5 (R-Type)
1
3
VIN
Power Input Voltage
5
1
VOUT
Output Voltage
2
2
GND
Ground
3
4
EN
4
5
BP
Enable Input Logic, Active Low. If the Shutdown Feature is not
Required, Connect EN to VIN.
Reference Noise Bypass
Function Block Diagram
EN
Shutdown
and
Logic Control
Quick
Start
BP
VIN
VREF
+
-
Error
Amplifier
MOS Driver
VOUT
Current-Limit
and
Thermal
Protection
GND
www.richtek.com
2
DS9178-18 April 2011
RT9178
Absolute Maximum Ratings
(Note 1)
Supply Input Voltage ----------------------------------------------------------------------------------------------- 7V
Enable Input Voltage ----------------------------------------------------------------------------------------------- 7V
Power Dissipation, PD @ TA = 25°C
SOT-23-5 -------------------------------------------------------------------------------------------------------------- 0.4W
Package Thermal Resistance (Note 2)
SOT-23-5, θJA -------------------------------------------------------------------------------------------------------- 250°C/W
Lead Temperature (Soldering, 10 sec.) ------------------------------------------------------------------------- 260°C
Junction Temperature ----------------------------------------------------------------------------------------------- 150°C
Storage Temperature Range -------------------------------------------------------------------------------------- −65°C to 150°C
ESD Susceptibility (Note 3)
HBM (Human Body Mode) ---------------------------------------------------------------------------------------- 2kV
MM (Machine Mode) ----------------------------------------------------------------------------------------------- 200V
Recommended Operating Conditions
(Note 4)
Supply Input Voltage ----------------------------------------------------------------------------------------------- 2.5V to 6V
Enable Input Voltage ----------------------------------------------------------------------------------------------- 0V to 6V
Junction Temperature Range -------------------------------------------------------------------------------------- −40°C to 125°C
Electrical Characteristics
(VIN = VOUT + 1V, CIN =COUT = 1μF, CBP = 1nF, TA = 25° C unless otherwise specified)
Parameter
Symbol
Test Conditions
Min
Typ
Max
Unit
Output Voltage Accuracy
ΔVOUT
IOUT = 1mA
−2
--
+2
%
Current Limit
ILIM
RLOAD = 1Ω
--
400
--
mA
IQ
VEN > 1.0V, IOUT = 0mA
--
90
150
μA
V DROP
IOUT = 200mA
--
200
300
mV
--
--
6
mV/V
Quiescent Current
Dropout Voltage
(Note 5)
(Note 6)
ΔVLINE
Line Regulation
VIN = (VO UT + 0.3V) to 6.0V,
IOUT = 1mA
Load Regulation
(Note 7)
ΔVLOA D 1mA < IO UT < 200mA
--
7
20
mV
Standby Current
(Note 8)
ISTBY
VEN = GND, Shutdown
--
0.01
1
μA
IIBSD
VEN = GND or VIN
--
0
100
nA
V IL
VIN = 3V to 5.5V, Shutdown
--
--
0.4
1.0
--
--
--
50
--
--
−70
--
--
−40
--
--
150
--
EN Input Bias Current
Logic-Low Voltage
EN Threshold
Logic-High Voltage V IH
Output Noise Voltage
Power Supply
Rejection Rate
eNO
f = 100Hz
f = 10kHz
Thermal Shutdown Temperature
DS9178-18 April 2011
PSRR
T SD
VIN = 3V to 5.5V, Start-Up
10Hz to 100kHz, IOUT = 200mA
COUT = 10μF
COUT = 10μF, IOUT = 200mA
V
μV RMS
dB
°C
www.richtek.com
3
RT9178
Note 1. Stresses listed as the above "Absolute Maximum Ratings" may cause permanent damage to the device. These are for
stress ratings. Functional operation of the device at these or any other conditions beyond those indicated in the
operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended
periods may remain possibility to affect device reliability.
Note 2. θ JA is measured in the natural convection at TA = 25°C on a low effective thermal conductivity test board of
JEDEC 51-3 thermal measurement standard.
Note 3. Devices are ESD sensitive. Handling precaution is recommended.
Note 4. The device is not guaranteed to function outside its operating conditions.
Note 5. Quiescent, or ground current, is the difference between input and output currents. It is defined by IQ = IIN - IOUT under
no load condition (IOUT = 0mA). The total current drawn from the supply is the sum of the load current plus the ground
pin current.
Note 6. The dropout voltage is defined as VIN -VOUT, which is measured when VOUT is VOUT(NORMAL) − 100mV.
Note 7. Regulation is measured at constant junction temperature by using a 20ms current pulse. Devices are tested for load
regulation in the load range from 1mA to 200mA.
Note 8. Standby current is the input current drawn by a regulator when the output voltage is disabled by a shutdown signal
(VEN = GND). It is measured with VIN = 6V.
www.richtek.com
4
DS9178-18 April 2011
RT9178
Typical Operating Characteristics
Output Voltage vs. Temperature
Quiescent Current vs. Temperature
100
95
3.3
3.1
2.9
VIN = 4V
CBP = 10nF
CIN = 1uF
COUT = 1uF
2.7
Quiescent Current (uA)
Output Voltage (V)
3.5
90
85
80
VIN = 4V
CBP = 10nF
CIN = 1uF
COUT = 1uF
75
70
2.5
-35
-15
5
25
45
65
85
105
-35
125
-15
5
25
PSRR
-10
-10
-20
-20
-30
100mA
-40
-50
1mA
-60
VIN = 4V
CBP = 10nF
CIN = 1uF
COUT = 1uF
TA = 25°C
-70
-80
-90
0.01
0.1
1
10
105
125
100
-50
VIN = 4V
CBP = 10nF
CIN = 1uF
COUT = 1uF
TA = -35°C
-60
-70
-80
-90
0.01
1000
1mA
100mA
-40
0.1
1
10
100
1000
Frequency (kHz)
Dropout Voltage vs. Load Current
Line Transient Response
Input Voltage
Deviation(V)
0.3
TJ = 125°C
0.2
TJ = 25°C
VIN = 3.2 to 3.8V
CBP = 10nF
CIN = 1uF
COUT = 10uF
3.8
3.2
0.15
0.1
TJ = -35°C
0.05
VIN = 4V
CBP = 10nF
CIN = 1uF
COUT = 1uF
0
0
25
50
75
100
125
150
175
200
Output Voltage
Deviation(mV)
Dropout Voltage (V)
85
-30
Frequency (kHz)
0.25
65
PSRR
0
PSRR (dB)
PSRR(dB)
0
45
Temperature (° C)
Temperature (° C)
20
0
-20
Time (500us/Div)
Load Current (mA)
DS9178-18 April 2011
www.richtek.com
5
RT9178
CIN = 1uF, Ceramic
COUT = 1uF, Ceramic
100
VIN = 4V
CBP = 10nF
IOUT = 100 to 200mA
20
0
-20
100
20
0
-20
Time (1ms/Div)
EN Pin
Input Voltage (V)
Start Up
4
2
0
3
2
VIN = 4V
CBP = 10nF
CIN = 1uF, Ceramic
COUT = 1uF, Ceramic
1
6
6
4
2
0
2
0
Time (5us/Div)
Time (10us/Div)
Start Up
Noise
2
100
Noise (uV)
VIN = 4V
150 CBP = 10nF
0
3
VIN = 4V
CBP = 100nF
CIN = 1uF, Ceramic
COUT = 1uF, Ceramic
Time (25us/Div)
www.richtek.com
6
CIN = 1uF, Ceramic
COUT = 1uF, Ceramic
50
0
-50
2
0
VIN = 4V
CBP = 10nF
CIN = 1uF, Ceramic
COUT = 10uF, Ceramic
1
4
1
Start Up
3
0
Output
EN Pin
Voltage(V) Input Voltage (V)
Time (1ms/Div)
Output
Voltage(V)
Output
EN Pin
Voltage(V) Input Voltage (V)
6
CIN = 1uF, Ceramic
COUT = 1uF, Ceramic
200
Output Voltage
Deviation (mV)
0
Load Transient Response
Load
Current (mA)
VIN = 4V
CBP = 10nF
IOUT = 1 to 100mA
Output Voltage
Deviation (mV)
Load
Current (mA)
Load Transient Response
-100
f = 10Hz to 100kHz
Time (10ms/Div)
DS9178-18 April 2011
RT9178
Application Information
Input Capacitor
An input capacitance of ≅1μF is required between the
device input pin and ground directly (the amount of the
capacitance may be increased without limit). The input
capacitor MUST be located less than 1 cm from the device
to assure input stability (see PCB Layout Section). A lower
ESR capacitor allows the use of less capacitance, while
higher ESR type (like aluminum electrolytic) require more
capacitance.
Capacitor types (aluminum, ceramic and tantalum) can
be mixed in parallel, but the total equivalent input
capacitance/ESR must be defined as above to stable
operation.
There are no requirements for the ESR on the input
capacitor, but tolerance and temperature coefficient must
be considered when selecting the capacitor to ensure the
capacitance will be ≅1μF over the entire operating
temperature range.
Output Capacitor
The RT9178 is designed specifically to work with very
small ceramic output capacitors. The recommended
minimum capacitance (temperature characteristics
X7R, X5R, Z5U or Y5V) is 1μF to 10μF range with 5mΩ to
50mΩ range ceramic capacitor between LDO output and
GND for transient stability, but it may be increased without
limit. Higher capacitance values help to improve transient.
The output capacitor's ESR is critical because it forms a
zero to provide phase lead which is required for loop
stability.
DS9178-18 April 2011
Region of Stable COUT ESR vs. Load Current
100
100.00
Unstable
10
10.00
COUT ESR (Ω)
The RT9178 is ideal for mobile phone and similar batterypowered wireless applications. It provides up to 200mA,
from a 2.5V to 6V input. Like any low-dropout regulator,
the device requires input and output decoupling capacitors.
These capacitors must be correctly selected for good
performance (see Capacitor Characteristics Section).
Please note that linear regulators with a low dropout
voltage have high internal loop gains which require care in
guarding against oscillation caused by insufficient
decoupling capacitance.
1.00
Stable
0.10
0.01
Unstable
0.00
0
40
80
120
160
200
Load Current (mA)
Reference Bypass Capacitor (BP)
Connecting a 10nF between the BP (reference bypass)
pin and GND significantly reduces noise on the regulator
output. It should be noted that the capacitor is connected
directly to a high impedance circuit in the band gap
reference. Because this circuit has only a few microamperes flowing into it, any significantly loading on this
node will cause a change on the regulated output voltage.
For this reason, DC leakage current through the noise
bypass capacitor must never exceed 100nA, and should
be kept as low as possible for best output voltage
accuracy. The type of capacitors best suited for the noise
bypass capacitor with either NP0 or C0G dielectric
typically have very low leakage. 10nF polypropylene and
polycarbonate film capacitors are available in small
surface mount packages and typically have extremely low
leakage current.
No Load Stability
The device will remain stable and in regulation with no
external load. This is specially important in CMOS RAM
keep-alive applications
Shutdown Input Operation
The RT9178 is shutdown by pulling the EN pin low, and
turned on by driving the input high. If the shutdown feature
is not required, the EN pin should be tied to VIN to keep
the regulator on at all times (the EN pin MUST NOT be
left floating).
www.richtek.com
7
RT9178
To assure proper operation, the signal source used to
drive the EN pin must be able to swing above and below
the specified turn-on/off voltage thresholds listed in the
“Electrical Characteristics” under VIH and VIL.The ON/
OFF signal may comes from either CMOS output, or an
open-collector output with pull-up resistor to the device
input voltage or another logic supply. The high-level voltage
may exceed the device input voltage, but must remain
within the absolute maximum ratings for the EN pin.
Quick Start-Up Time
The start-up time is determined by the time constant of
the bypass capacitor. The smaller the capacitor value, the
shorter the power up time, but less noise gets reduced.
As a result, start-up time and noise reduction need to be
taken into design consideration when choosing the value
of the bypass capacitor.
Input-Output (Dropout) Voltage
A regulator's minimum input-to-output voltage differential
(dropout voltage) determines the lowest usable supply
voltage. In battery-powered systems, this determines the
useful end-of-life battery voltage. Because the device uses
a PMOS, its dropout voltage is a function of drain-tosource on-resistance, RDS(ON), multiplied by the load
current:
VDROPOUT = VIN - VOUT = RDS(ON) × IOUT
Current Limit
The RT9178 monitors and controls the PMOS’ gate
voltage, limiting the output current to 400mA (typ). The
output can be shorted to ground for an indefinite period of
time without damaging the part.
Short-Circuit Protection
The device is short circuit protected and in the event of a
peak over-current condition, the short-circuit control loop
will rapidly drive the output PMOS pass element off. Once
the power pass element shuts down, the control loop will
rapidly cycle the output on and off until the average power
dissipation causes the thermal shutdown circuit to
respond to servo the on/off cycling to a lower frequency.
Please refer to the section on thermal information for power
dissipation calculations.
www.richtek.com
8
Capacitor Characteristics
It is important to note that capacitance tolerance and
variation with temperature must be taken into
consideration when selecting a capacitor so that the
minimum required amount of capacitance is provided over
the full operating temperature range. In general, a good
tantalum capacitor will show very little capacitance
variation with temperature, but a ceramic may not be as
good (depending on dielectric type).
Aluminum electrolytics also typically have large temperature
variation of capacitance value.
Equally important to consider is a capacitor's ESR change
with temperature: this is not an issue with ceramics, as
their ESR is extremely low. However, it is very important
in Tantalum and aluminum electrolytic capacitors. Both
show increasing ESR at colder temperatures, but the
increase in aluminum electrolytic capacitors is so severe
they may not be feasible for some applications.
Ceramic:
For values of capacitance in the 10μF to 100μF range,
ceramics are usually larger and more costly than tantalums
but give superior AC performance for by-passing high
frequency noise because of very low ESR (typically
less than 10mΩ). However, some dielectric types do not
have good capacitance characteristics as a function of
voltage and temperature.
Z5U and Y5V dielectric ceramics have capacitance that
drops severely with applied voltage. A typical Z5U or Y5V
capacitor can lose 60% of its rated capacitance with
half of the rated voltage applied to it. The Z5U and Y5V
also exhibit a severe temperature effect, losing more than
50% of nominal capacitance at high and low limits of the
temperature range.
X7R and X5R dielectric ceramic capacitors are strongly
recommended if ceramics are used, as they typically
maintain a capacitance range within ± 20% of nominal
over full operating ratings of temperature and voltage. Of
course, they are typically larger and more costly than Z5U/
Y5U types for a given voltage and capacitance.
DS9178-18 April 2011
RT9178
Tantalum:
Thermal Considerations
Solid tantalum capacitors are recommended for use on
the output because their typical ESR is very close to the
ideal value required for loop compensation. They also work
well as input capacitors if selected to meet the ESR
requirements previously listed.
The RT9178 series can deliver a current of up to 200mA
over the full operating junction temperature range. However,
the maximum output current must be derated at higher
ambient temperature to ensure the junction temperature
does not exceed 125°C.
Tantalums also have good temperature stability: a good
quality tantalum will typically show a capacitance value
that varies less than 10 to 15% across the full temperature
range of 125°C to −40°C. ESR will vary only about 2X
going from the high to low temperature limits.
With all possible conditions, the junction temperature must
be within the range specified under operating conditions.
Power dissipation can be calculated based on the output
current and the voltage drop across regulator.
The increasing ESR at lower temperatures can cause
oscillations when marginal quality capacitors are used (if
the ESR of the capacitor is near the upper limit of the
stability range at room temperature).
The final operating junction temperature for any set of
conditions can be estimated by the following thermal
equation:
Aluminum:
Where TJ (MAX) is the maximum junction temperature of
the die (125°C) and T A is the maximum ambient
temperature. The junction to ambient thermal resistance
(θJA) for SOT-23-5 package at recommended minimum
footprint is 250°C/W (θJA is layout dependent). Visit our
website in which “Recommended Footprints for Soldering
Surface Mount Packages” for detail.
This capacitor type offers the most capacitance for the
money. The disadvantages are that they are larger in
physical size, not widely available in surface mount, and
have poor AC performance (especially at higher frequencies)
due to higher ESR and ESL.
Compared by size, the ESR of an aluminum electrolytic
is higher than either Tantalum or ceramic, and it also varies
greatly with temperature. A typical aluminum electrolytic
can exhibit an ESR increase of as much as 50X when
going from 25°C down to −40°C.
It should also be noted that many aluminum electrolytics
only specify impedance at a frequency of 120Hz, which
indicates they have poor high frequency performance.
Only aluminum electrolytics that have an impedance
specified at a higher frequency (between 20kHz and
100kHz) should be used for the device. Derating must be
applied to the manufacturer's ESR specification, since it
is typically only valid at room temperature.
Any applications using aluminum electrolytics should be
thoroughly tested at the lowest ambient operating
temperature where ESR is maximum.
DS9178-18 April 2011
PD = (VIN − VOUT) IOUT + VIN IGND
PD (MAX) = ( TJ (MAX) − TA ) / θJA
PCB Layout
Good board layout practices must be used or instability
can be induced because of ground loops and voltage drops.
The input and output capacitors MUST be directly
connected to the input, output, and ground pins of the
device using traces which have no other currents flowing
through them.
The best way to do this is to layout CIN and COUT near the
device with short traces to the VIN, VOUT, and ground pins.
The regulator ground pin should be connected to the
external circuit ground so that the regulator and its
capacitors have a “single point ground”.
www.richtek.com
9
RT9178
It should be noted that stability problems have been seen
in applications where “vias” to an internal ground plane
were used at the ground points of the device and the input
and output capacitors. This was caused by varying ground
potentials at these nodes resulting from current flowing
through the ground plane. Using a single point ground
technique for the regulator and it’ s capacitors fixed the
problem. Since high current flows through the traces going
into VIN and coming from VOUT, Kelvin connect the capacitor
leads to these pins so there is no voltage drop in series
with the input and output capacitors.
Optimum performance can only be achieved when the
device is mounted on a PC board according to the diagram
below:
BP
VOUT
VIN
GND
EN
SOT-23-5 Board Layout
www.richtek.com
10
DS9178-18 April 2011
RT9178
Outline Dimension
H
D
L
B
C
b
A
A1
e
Dimensions In Millimeters
Dimensions In Inches
Symbol
Min
Max
Min
Max
A
0.889
1.295
0.035
0.051
A1
0.000
0.152
0.000
0.006
B
1.397
1.803
0.055
0.071
b
0.356
0.559
0.014
0.022
C
2.591
2.997
0.102
0.118
D
2.692
3.099
0.106
0.122
e
0.838
1.041
0.033
0.041
H
0.080
0.254
0.003
0.010
L
0.300
0.610
0.012
0.024
SOT-23-5 Surface Mount Package
Richtek Technology Corporation
Richtek Technology Corporation
Headquarter
Taipei Office (Marketing)
5F, No. 20, Taiyuen Street, Chupei City
5F, No. 95, Minchiuan Road, Hsintien City
Hsinchu, Taiwan, R.O.C.
Taipei County, Taiwan, R.O.C.
Tel: (8863)5526789 Fax: (8863)5526611
Tel: (8862)86672399 Fax: (8862)86672377
Email: [email protected]
Information that is provided by Richtek Technology Corporation is believed to be accurate and reliable. Richtek reserves the right to make any change in circuit
design, specification or other related things if necessary without notice at any time. No third party intellectual property infringement of the applications should be
guaranteed by users when integrating Richtek products into any application. No legal responsibility for any said applications is assumed by Richtek.
DS9178-18 April 2011
www.richtek.com
11