PC3H5J00000F

PC3H5J00000F Series
PC3H5J00000F
Series
Mini-flat Half Pitch Package,
Darlington Phototransistor Output
Photocoupler
■ Description
■ Agency approvals/Compliance
PC3H5J00000F Series contains an IRED optically
coupled to a phototransistor.
It is packaged in a 4-pin Mini-flat, Half pitch type.
Input-output isolation voltage(rms) is 2.5kV.
CTR is MIN. 600% at input current of 1mA.
1. Recognized by UL1577 (Double protection isolation),
file No. E64380 (as model No. PC3H5)
2. Approved by VDE, DIN EN60747-5-2 (∗) (as an
option), file No. 40009162 (as model No. PC3H5)
3. Package resin : UL flammability grade (94V-0)
(∗)
DIN EN60747-5-2 : successor standard of DIN VDE0884
■ Features
1. 4-pin Mini-flat Half pitch package (Lead pitch :
1.27mm)
2. Double transfer mold package (Ideal for Flow
Soldering)
3. Darlington phototransistor output (CTR : MIN. 600%
at IF=1mA, VCE=2V)
4. Isolation voltage between input and output (Viso(rms) :
2.5kV)
5. RoHS directive compliant
■ Applications
1. Programmable controllers
2. Facsimiles
3. Telephones
Notice The content of data sheet is subject to change without prior notice.
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP
devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
1
Sheet No.: D2-A01702FEN
Date Jun. 30. 2005
© SHARP Corporation
PC3H5J00000F Series
■ Internal Connection Diagram
4
1
1
2
3
2
3
4
Anode
Cathode
Emitter
Collector
■ Outline Dimensions
(Unit : mm)
VDE option
3 H5
4.4±0.2
Epoxy resin
VDE
Indenfication mark
Epoxy resin
0.2±0.05
(1.7)
0.1±0.1 2.0±0.2
0.2±0.05
3
5.3±0.3
(1.7)
0.5+0.4
−0.2
3H5 4
2
4.4±0.2
5.3±0.3
7.0+0.2
−0.7
4
0.5+0.4
−0.2
7.0+0.2
−0.7
*( ) : Reference Dimensions
0.1±0.1 2.0±0.2
3
2
Date code
1
0.4±0.1
4
2.6±0.3
1
1.27±0.25
SHARP mark "S"
Anode mark
Date code
0.4±0.1
1.27±0.25
2.6±0.3
SHARP mark "S"
Anode mark
*( ) : Reference Dimensions
Product mass : approx. 0.05g
Product mass : approx. 0.05g
Plating material : SnCu (Cu : TYP. 2%)
Sheet No.: D2-A01702FEN
2
PC3H5J00000F Series
Date code (2 digit)
A.D.
1990
1991
1992
1993
1994
1995
1996
1997
1998
1999
2000
2001
1st digit
Year of production
A.D
Mark
2002
A
2003
B
2004
C
2005
D
2006
E
2007
F
2008
H
2009
J
2010
K
2011
L
2012
M
··
N
·
Mark
P
R
S
T
U
V
W
X
A
B
C
··
·
2nd digit
Month of production
Month
Mark
January
1
February
2
March
3
April
4
May
5
June
6
July
7
August
8
September
9
October
O
November
N
December
D
repeats in a 20 year cycle
Country of origin
Japan
Rank mark
There is no rank mark indicator.
Sheet No.: D2-A01702FEN
3
PC3H5J00000F Series
■ Absolute Maximum Ratings
Output
Input
Parameter
Symbol
IF
Forward current
*1
Peak forward current
IFM
Reverse voltage
VR
P
Power dissipation
Collector-emitter voltage VCEO
Emitter-collector voltage VECO
Collector current
IC
Collector power dissipation
PC
Total power dissipation
Ptot
Operating temperature
Topr
Storage temperature
Tstg
*2
Isolation voltage
Viso (rms)
*3
Soldering temperature
Tsol
Rating
50
1
6
70
35
6
80
150
170
−30 to +100
−40 to +125
2.5
260
(Ta=25˚C)
Unit
mA
A
V
mW
V
V
mA
mW
mW
˚C
˚C
kV
˚C
*1 Pulse width≤100µs, Duty ratio : 0.001
*2 40 to 60%RH, AC for 1 minute
*3 For 10s
■ Electro-optical Characteristics
Input
Output
Transfer
characteristics
Symbol
Parameter
VF
Forward voltage
Reverse current
IR
Terminal capacitance
Ct
Collector dark current
ICEO
Collector-emitter breakdown voltage BVCEO
Emitter-collector breakdown voltage BVECO
Collector current
IC
Collector-emitter saturation voltage VCE (sat)
Isolation resistance
RISO
Floating capacitance
Cf
Rise time
tr
Response time
Fall time
tf
Conditions
IF=20mA
VR=4V
V=0, f=1kHz
VCE=10V, IF=0
IC=0.1mA, IF=0
IE=10µA, IF=0
IF=1mA, VCE=2V
IF=1mA, IC=2mA
DC500V, 40 to 60%RH
V=0, f=1MHz
VCE=2V, IC=2mA, RL=100Ω
MIN.
−
−
−
−
35
6
6
−
5×1010
−
−
−
TYP.
1.2
−
30
−
−
−
16
0.8
1×1011
0.6
60
53
MAX.
1.4
10
250
1000
−
−
75
1.0
−
1.0
300
250
(Ta=25˚C)
Unit
V
µA
pF
nA
V
V
mA
V
Ω
pF
µs
µs
Sheet No.: D2-A01702FEN
4
PC3H5J00000F Series
■ Model Line-up
Taping
3 000pcs/reel
DIN EN60747-5-2
Approved
Model No.
PC3H5J00000F PC3H5YJ0000F
Package
Please contact a local SHARP sales representative to inquire about production status.
Sheet No.: D2-A01702FEN
5
PC3H5J00000F Series
Fig.2 Diode Power Dissipation vs.
Ambient Temperature
Fig.1 Forward Current vs. Ambient
Temperature
100
Diode power dissipation P (mW)
Forward current IF (mA)
50
40
30
20
10
0
−30
0
25
50 55
75
100
80
70
60
40
20
0
−30
125
0
Fig.3 Collector Power Dissipation vs.
Ambient Temperature
100
125
250
Total power dissipation Ptot (mW)
Collector power dissipation PC (mW)
75
Fig.4 Total Power Dissipation vs. Ambient
Temperature
250
200
150
100
50
0
−30
0
25
50
75
100
200
170
150
100
50
0
−30
125
Fig.5 Peak Forward Current vs. Duty Ratio
Forward current IF (mA)
10−2
10−1
50
75
100
125
100
100
10−3
25
Fig.6 Forward Current vs. Forward Voltage
Pulse width≤100µs
Ta=25˚C
1 000
0
Ambient temperature Ta (˚C)
Ambient temperature Ta (˚C)
Peak forward current IFM (mA)
50 55
Ambient temperature Ta (˚C)
Ambient temperature Ta (˚C)
10
25
T a =50˚C
75˚C
100˚C
10
25˚C
0˚C
− 30˚C
1
0.1
1
0
Duty ratio
0.5
1
1.5
2
Forward voltage VF (V)
Sheet No.: D2-A01702FEN
6
PC3H5J00000F Series
Fig.7 Current Transfer Ratio vs. Forward
Current
Fig.8 Collector Current vs. Collector-emitter
Voltage
100
2 000
VCE=2V
Ta=25˚C
Ta=25˚C
90
80
1 600
Collector current IC (mA)
Current transfer ratio CTR(%)
1 800
1 400
1 200
1 000
800
600
IF=10mA
70
PC (MAX.)
60
5mA
50
40
2mA
30
400
20
200
0
0.1
10
1mA
0
1
0
10
1
Fig.9 Relative Current Transfer Ratio vs.
Ambient Temperature
Collector-emitter saturation voltage VCE(sat) (V)
Relative current transfer ratio (%)
4
1.3
IF=1mA
VCE=2V
100
50
0
25
50
5
75
100
IF=1mA
IC=2mA
1.2
1.1
1
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
−30
0
Ambient temperature Ta (˚C)
25
50
75
100
Ambient temperature Ta (˚C)
Fig.12 Collector-emitter Saturation Voltage
vs. Forward Current
Fig.11 Collector Dark Current vs. Ambient
Temperature
10−4
8
VCE=10V
Collector-emitter Saturation Voltage
VCE (sat) (V)
10−5
Collector dark current ICEO (A)
3
Fig.10 Collector - emitter Saturation Voltage
vs. Ambient Temperature
150
0
−30
2
Collector-emitter voltage VCE (V)
Forward current IF (mA)
−6
10
10−7
−8
10
−9
10
10−10
Ta=25˚C
IC=0.5mA
7
1mA
6
3mA
5
5mA
7mA
4
50mA
3
2
30mA
1
10−11
−30
0
20
40
60
80
0
100
0
0.5
1
1.5
2
2.5
3
3.5
4
Forward current IF (mA)
Ambient temperature Ta (˚C)
Remarks : Please be aware that all data in the graph are just for reference and not for guarantee.
Sheet No.: D2-A01702FEN
7
PC3H5J00000F Series
■ Design Considerations
● Design guide
While operating at IF<1.0mA, CTR variation may increase.
Please make design considering this fact.
This product is not designed against irradiation and incorporates non-coherent IRED.
● Degradation
In general, the emission of the IRED used in photocouplers will degrade over time.
In the case of long term operation, please take the general IRED degradation (50% degradation over 5
years) into the design consideration.
● Recommended Foot Print (reference)
0.8
1.27
6.3
1.5
(Unit : mm)
✩ For additional design assistance, please review our corresponding Optoelectronic Application Notes.
Sheet No.: D2-A01702FEN
8
PC3H5J00000F Series
■ Manufacturing Guidelines
● Soldering Method
Reflow Soldering:
Reflow soldering should follow the temperature profile shown below.
Soldering should not exceed the curve of temperature profile and time.
Please don't solder more than twice.
(˚C)
300
Terminal : 260˚C peak
( package surface : 250˚C peak)
200
Reflow
220˚C or more, 60s or less
Preheat
150 to 180˚C, 120s or less
100
0
0
1
2
3
4
(min)
Flow Soldering :
Due to SHARP's double transfer mold construction submersion in flow solder bath is allowed under the below
listed guidelines.
Flow soldering should be completed below 260˚C and within 10s.
Preheating is within the bounds of 100 to 150˚C and 30 to 80s.
Please don't solder more than twice.
Hand soldering
Hand soldering should be completed within 3s when the point of solder iron is below 400˚C.
Please don't solder more than twice.
Other notices
Please test the soldering method in actual condition and make sure the soldering works fine, since the impact
on the junction between the device and PCB varies depending on the tooling and soldering conditions.
Sheet No.: D2-A01702FEN
9
PC3H5J00000F Series
● Cleaning instructions
Solvent cleaning:
Solvent temperature should be 45˚C or below Immersion time should be 3 minutes or less
Ultrasonic cleaning:
The impact on the device varies depending on the size of the cleaning bath, ultrasonic output, cleaning time,
size of PCB and mounting method of the device.
Therefore, please make sure the device withstands the ultrasonic cleaning in actual conditions in advance of
mass production.
Recommended solvent materials:
Ethyl alcohol, Methyl alcohol and Isopropyl alcohol
In case the other type of solvent materials are intended to be used, please make sure they work fine in
actual using conditions since some materials may erode the packaging resin.
● Presence of ODC
This product shall not contain the following materials.
And they are not used in the production process for this product.
Regulation substances : CFCs, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methylchloroform)
Specific brominated flame retardants such as the PBBOs and PBBs are not used in this product at all.
This product shall not contain the following materials banned in the RoHS Directive (2002/95/EC).
•Lead, Mercury, Cadmium, Hexavalent chromium, Polybrominated biphenyls (PBB), Polybrominated
diphenyl ethers (PBDE).
Sheet No.: D2-A01702FEN
10
PC3H5J00000F Series
■ Package specification
● Tape and Reel package
Package materials
Carrier tape : PS
Cover tape : PET (three layer system)
Reel : PS
Carrier tape structure and Dimensions
F
G
D
J
I
L
K
Dimensions List
A
B
12.0±0.3
5.5±0.1
H
I
7.5±0.1
0.3±0.05
C
1.75±0.1
J
2.3±0.1
D
8.0±0.1
K
3.1±0.1
E
2.0±0.1
L
+0.1
φ1.6−0
5˚
MAX
.
H
H
A
B
C
E
(Unit : mm)
F
G
+0.1
4.0±0.1
φ1.5−0
Reel structure and Dimensions
e
d
c
g
Dimensions List
a
b
330
13.5±1.5
e
f
±1.0
23
2.0±0.5
f
a
b
(Unit : mm)
c
d
±1.0
100
13±0.5
g
2.0±0.5
Direction of product insertion
Pull-out direction
[Packing : 3 000pcs/reel]
Sheet No.: D2-A01702FEN
11
PC3H5J00000F Series
■ Important Notices
with equipment that requires higher reliability such as:
--- Transportation control and safety equipment (i.e.,
aircraft, trains, automobiles, etc.)
--- Traffic signals
--- Gas leakage sensor breakers
--- Alarm equipment
--- Various safety devices, etc.
(iii) SHARP devices shall not be used for or in
connection with equipment that requires an extremely
high level of reliability and safety such as:
--- Space applications
--- Telecommunication equipment [trunk lines]
--- Nuclear power control equipment
--- Medical and other life support equipment (e.g.,
scuba).
· The circuit application examples in this publication are
provided to explain representative applications of
SHARP devices and are not intended to guarantee any
circuit design or license any intellectual property rights.
SHARP takes no responsibility for any problems
related to any intellectual property right of a third party
resulting from the use of SHARP's devices.
· Contact SHARP in order to obtain the latest device
specification sheets before using any SHARP device.
SHARP reserves the right to make changes in the
specifications, characteristics, data, materials,
structure, and other contents described herein at any
time without notice in order to improve design or
reliability. Manufacturing locations are also subject to
change without notice.
· If the SHARP devices listed in this publication fall
within the scope of strategic products described in the
Foreign Exchange and Foreign Trade Law of Japan, it
is necessary to obtain approval to export such SHARP
devices.
· Observe the following points when using any devices
in this publication. SHARP takes no responsibility for
damage caused by improper use of the devices which
does not meet the conditions and absolute maximum
ratings to be used specified in the relevant specification
sheet nor meet the following conditions:
(i) The devices in this publication are designed for use
in general electronic equipment designs such as:
--- Personal computers
--- Office automation equipment
--- Telecommunication equipment [terminal]
--- Test and measurement equipment
--- Industrial control
--- Audio visual equipment
--- Consumer electronics
(ii) Measures such as fail-safe function and redundant
design should be taken to ensure reliability and safety
when SHARP devices are used for or in connection
· This publication is the proprietary product of SHARP
and is copyrighted, with all rights reserved. Under the
copyright laws, no part of this publication may be
reproduced or transmitted in any form or by any
means, electronic or mechanical, for any purpose, in
whole or in part, without the express written permission
of SHARP. Express written permission is also required
before any use of this publication may be made by a
third party.
· Contact and consult with a SHARP representative if
there are any questions about the contents of this
publication.
[E206]
Sheet No.: D2-A01702FEN
12