PR36MF12NSZF

PR26MF1xNSZ Series
PR36MF1xNSZ Series
IT(rms)≤0.6A, Non-Zero Cross type
DIP 8pin
Triac output SSR
PR26MF1xNSZ Series
PR36MF1xNSZ Series
∗
Zero cross type is also available. (PR26MF21NSZ Series/
PR36MF2xNSZ Series)
■ Description
■ Agency approvals/Compliance
PR26MF1xNSZ Series and PR36MF1xNSZ Series
Solid State Relays (SSR) are an integration of an
infrared emitting diode (IRED), a Phototriac Detector
and a main output Triac. These devices are ideally
suited for controlling high voltage AC loads with solid
state reliability while providing 4.0kV isolation
(Viso(rms)) from input to output.
1. Recognized by UL508, file No. E94758 (as model No.
R26MF1/R36MF1)
2. Approved by CSA 22.2 No.14, file No. LR63705 (as
model No. R26MF1/R36MF1)
3. Optionary available VDE approved (∗)(DIN EN 60747-52), file No. 40008898 (only for PR36MF1xNSZ Series
as model No. R36MF1)
4. Package resin : UL flammability grade (94V-0)
(∗)
■ Features
1. Output current, IT(rms)≤0.6A
2. Non-zero crossing functionary
3. 8 pin DIP package (SMT gullwing also available)
4. High repetitive peak off-state voltage
(VDRM : 600V, PR36MF1xNSZ Series)
(VDRM : 400V, PR26MF1xNSZ Series)
5. I FT ranks available (see Model Line-up in this
datasheet)
6. Superior noise immunity (dV/dt : MIN. 100V/µs)
7. Response time, ton : MAX. 100µs
8. High isolation voltage between input and output
(V iso (rms) : 4.0kV)
DIN EN60747-5-2 : successor standard of DIN VDE0884.
Up to Date code "RD" (December 2003), approval of DIN
VDE0884.
From Date code "S1" (January 2004), approval of DIN
EN60747-5-2.
■ Applications
1. Isolated interface between high voltage AC devices
and lower voltage DC control circuitry.
2. Switching motors, fans, heaters, solenoids, and
valves.
3. Phase or power control in applications such as
lighting and temperature control equipment.
(
Notice The content of data sheet is subject to change without prior notice.
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP
devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
1
Sheet No.: D4-A00401FEN
Date Mar. 31. 2004
© SHARP Corporation
PR26MF1xNSZ Series
PR36MF1xNSZ Series
■ Internal Connection Diagram
8
5
6
1
2
3
4
1
2
3
Cathode
Anode
Cathode
Cathode
5
6
8
Gate
Output (T1)
Output (T2)
4
■ Outline Dimensions
(Unit : mm)
1.2±0.3
1.2±0.3
1.05±0.2
6
5
Model No.
SHARP
mark
"S"
R26MF1
Rank mark
CSA mark
θ:0 to 13˚
0.26±0.1
0.5TYP. 3.5±0.5
3.25±0.5
θ
1.2±0.3
SHARP
mark
"S"
Rank mark
3
5
R36MF1
Model No.
Rank mark
1
2
3
7.62±0.3
0.26±0.1
9.66±0.5
Epoxy resin
2.54±0.25
0.26±0.1
0.5±0.1
θ
Product mass : approx. 0.56g
4
Date code (2 digit)
Factory identification mark
Anode
mark
7.62±0.3
0.5TYP. 3.5±0.5
3.25±0.5
6
4
9.66±0.5
2.54±0.25
8
1.05±0.2
CSA mark
Date code (2 digit)
Factory identification mark
Anode
mark
1.0+0.4
−0
4. SMT Gullwing Lead-Form [ex. PR36MF11NIPF]
Model No.
CSA mark
Epoxy resin
Product mass : approx. 0.54g
6.5±0.5
R36MF1
1.0+0.4
−0
10.0+0
−0.5
1.05±0.2
5
7.62±0.3
2.54±0.25
0.26±0.1
0.5±0.1
6
4
Date code (2 digit)
Factory identification mark
Epoxy resin
3. Through-Hole [ex. PR36MF11NSZF]
8
3
9.66±0.5
θ
1.2±0.3
2
0.35±0.25
1
Anode
mark
7.62±0.3
Product mass : approx. 0.56g
2
Rank mark
4
2.54±0.25
1
R26MF1
CSA mark
Date code (2 digit)
Factory identification mark
9.66±0.5
SHARP
mark
"S"
Model No.
θ:0 to 13˚
1.0+0.4
−0
Epoxy resin
0.35±0.25
3
5
3.5±0.5
2
6
6.5±0.5
1
Anode
mark
8
1.05±0.2
3.5±0.5
8
6.5±0.5
SHARP
mark
"S"
2. SMT Gullwing Lead-Form [ex. PR26MF11NIPF]
6.5±0.5
1. Through-Hole [ex. PR26MF11NSZF]
1.0+0.4
−0
10.0+0
−0.5
θ
Product mass : approx. 0.54g
Sheet No.: D4-A00401FEN
2
PR26MF1xNSZ Series
PR36MF1xNSZ Series
■ Outline Dimensions
(Unit : mm)
5. Through-Hole VDE option [ex. PR36MF11YSZF]
R36MF1
4
Model No.
5
SHARP
mark
"S"
2
VDE identification mark
1
2
3
Date code (2 digit)
Factory identification mark
Anode
mark
Epoxy resin
2.54±0.25
0.26±0.1
0.5±0.1
θ
Product mass : approx. 0.56g
4
7.62±0.3
9.66±0.5
0.5TYP. 3.5±0.5
3.25±0.5
Rank mark
7.62
9.66
2.54±0.25
R36MF1
±0.3
±0.5
Model No.
0.26±0.1
1
5
CSA mark
VDE identification mark
3
4
Date code (2 digit)
Factory identification mark
Anode
mark
6
4
Rank mark
CSA mark
8
θ:0 to 13˚
1.0+0.4
−0
Epoxy resin
0.35±0.25
6
1.05±0.2
6.5±0.5
8
6.5±0.5
SHARP
mark
"S"
1.2±0.3
1.05±0.2
3.5±0.5
1.2±0.3
6. SMT Gullwing Lead-Form VDE option [ex. PR36MF11YIPF]
1.0+0.4
−0
10.0+0
−0.5
θ
Product mass : approx. 0.54g
Sheet No.: D4-A00401FEN
3
PR26MF1xNSZ Series
PR36MF1xNSZ Series
Date code (2 digit)
A.D.
1990
1991
1992
1993
1994
1995
1996
1997
1998
1999
2000
2001
1st digit
Year of production
A.D
Mark
2002
A
2003
B
2004
C
2005
D
2006
E
2007
F
2008
H
2009
J
2010
K
2011
L
2012
M
··
N
·
2nd digit
Month of production
Month
Mark
January
1
February
2
March
3
April
4
May
5
June
6
July
7
August
8
September
9
October
O
November
N
December
D
Mark
P
R
S
T
U
V
W
X
A
B
C
··
·
repeats in a 20 year cycle
Factory identification mark
Factory identification Mark
Country of origin
no mark
Japan
* This factory marking is for identification purpose only.
Please contact the local SHARP sales representative to see the actural status of the
production.
Rank mark
Please refer to the Model Line-up table.
Sheet No.: D4-A00401FEN
4
PR26MF1xNSZ Series
PR36MF1xNSZ Series
(Ta=25˚C)
Parameter
Symbol Rating
Unit
*3
IF
50
mA
Forward current
Input
VR
6
V
Reverse voltage
*3
I
(rms)
0.6
A
RMS ON-state current
T
*4
Isurge
6
A
Peak one cycle surge current
Output
PR26MF1xNSZ
400
Repetitive
VDRM
V
600
peak OFF-state voltage PR36MF1xNSZ
*1
Viso(rms)
kV
4.0
Isolation voltage
−25 to +85
Topr
˚C
Operating temperature
Tstg −40 to +125
˚C
Storage temperature
*2
Tsol
270 *5
˚C
Soldering temperature
1mm
■ Absolute Maximum Ratings
Soldering area
*1 40 to 60%RH, AC for 1minute, f=60Hz
*2 For 10s
*3 Refer to Fig.1, Fig.2
*4 f=50Hz sine wave
*5 Lead solder plating models: 260˚C
■ Electro-optical Characteristics
Parameter
Forward voltage
Input
Reverse current
Repetitive peak OFF-state current
ON-state voltage
Output
Holding current
Critical rate of rise of OFF-state voltage
Rank 1
Minimum trigger current
Rank 2
Transfer
charac- Isolation resistance
teristics
Rank 1
Turn-on time
Rank 2
(Ta=25˚C)
Symbol
VF
IR
IDRM
VT
IH
dV/dt
Conditions
IF=20mA
VR=3V
VD=VDRM
IT=0.6A
VD=6V
−
VD=1/√2 ·VDRM
IFT
VD=6V, RL=100Ω
RISO
DC500V,40 to 60%RH
VD=6V, RL=100Ω, IF=20mA
VD=6V, RL=100Ω, IF=10mA
ton
MIN. TYP.
1.2
−
−
−
−
−
−
−
−
−
−
100
−
−
−
−
10
1011
5×10
−
−
MAX.
1.4
10
100
3.0
25
−
10
5
−
Unit
V
µA
µA
V
mA
V/µs
100
µs
mA
Ω
Sheet No.: D4-A00401FEN
5
PR26MF1xNSZ Series
PR36MF1xNSZ Series
Model Line-up
Lead Form
Shipping Package
DIN
EN60747-5-2
Model No.
Through-Hole
Sleeve
50pcs/sleeve
-
PR36MF11NSZF
PR36MF12NSZF
PR26MF11NSZF
PR26MF12NSZF
Approved
PR36MF11YSZF
PR36MF12YSZF
-
SMT Gullwing
Taping
1 000pcs/reel
PR36MF11NIPF
PR36MF12NIPF
PR26MF11NIPF
PR26MF12NIPF
V DRM
[V]
Rank mark
IFT [mA]
(V D =6V,
R L =100Ω )
1
2
1
2
MAX.10
MAX.5
MAX.10
MAX.5
Approved
PR36MF11YIPF
PR36MF12YIPF
-
600
400
Please contact a local SHARP sales representative to see the actual status of the production.
Sheet No.: D4-A00401FEN
6
PR26MF1xNSZ Series
PR36MF1xNSZ Series
Fig.2 RMS ON-state Current vs.
Ambient Temperature
70
0.7
60
0.6
RMS ON-state current IT (rms) (A)
Forward current IF (mA)
Fig.1 Forward Current vs. Ambient
Temperature
50
40
30
20
10
0
−25
0
50
0.5
0.4
0.3
0.2
0.1
0
−25
100
0
Ambient temperature Ta (˚C)
Fig.3-b Forward Current vs.
Forward Voltage (Rank 2)
0˚C
100
100
Ta=75˚C
50
Forward current IF (mA)
Forward current IF (mA)
Ta=75˚C
−25˚C
50˚C
10
5
1
0
0.5
1
1.5
2
2.5
50
50˚C
25˚C
5
−25˚C
1
0.9
3
1
1.1
Minimum trigger current IFT (mA)
PR26MF11NSZ
8
6
PR36MF11NSZ
4
2
40
1.5
VD=6V
RL=100Ω
10
20
1.4
6
VD=6V
RL=100Ω
0
1.3
Fig.4-b Minimum Trigger Current vs.
Ambient Temperature (Rank 2)
12
−20
1.2
Forward voltage VF (V)
Fig.4-a Minimum Trigger Current vs.
Ambient Temperature (Rank 1)
0
−40
0˚C
10
Forward voltage VF (V)
Minimum trigger current IFT (mA)
100
Ambient temperature Ta (˚C)
Fig.3-a Forward Current vs.
Forward Voltage (Rank 1)
25˚C
50
60
80
5
4
3
2
1
0
−30
100
Ambient temperature Ta (˚C)
0
50
100
Ambient temperature Ta (˚C)
Sheet No.: D4-A00401FEN
7
PR26MF1xNSZ Series
PR36MF1xNSZ Series
Fig.5 ON-state Voltage vs.
Ambient Temperature
Fig.6 Relative Holding Current vs.
Ambient Temperature
1.6
Relative holding current IH (t˚C) / IH (25˚C)×100%
1 000
IT=0.6A
ON-state voltage VT (V)
1.5
1.4
1.3
1.2
1.1
1
−40
−20
0
20
40
60
80
100
VD=6V
100
10
−30
120
Ambient temperature Ta (˚C)
0
20
40
60
100
Ambient temperature Ta (˚C)
Fig.7 ON-state Current vs. ON-state Voltage
Fig.8-a Turn-on Time vs. Forward Current
(Rank 1)
1 000
1.2
VD=6V
RL=100Ω
Ta=25˚C
IF=20mA
Ta=25˚C
Turn-on time tON (µs)
1
ON-state current IT (A)
80
0.8
0.6
0.4
100
PR36MF11NSZ
10
PR26MF11NSZ
0.2
0
0
0.5
1
1.5
1
10
2
ON-state voltage VT (V)
20
30
40
50
100
Forward current IF (mA)
Fig.8-b Turn-on Time vs. Forward Current
(Rank 2)
Turn-on time tON (µs)
1 000
VD=6V
RL=100Ω
Ta=25˚C
100
10
Remarks : Please be aware that all data in the graph
are just for reference.
1
1
10
100
Forward current IF (mA)
Sheet No.: D4-A00401FEN
8
PR26MF1xNSZ Series
PR36MF1xNSZ Series
■ Design Considerations
● Recommended Operating Conditions
Input
Output
Parameter
Symbol
Input signal current
Rank 1
IF(ON)
at ON state
Rank 2
Input signal current at OFF state
IF(OFF)
PR26MF1xNSZ
Load supply voltage
VOUT(rms)
PR36MF1xNSZ
Load supply current
Frequency
Operating temperature
IOUT(rms)
f
Topr
Conditions
−
MIN.
20
10
0
−
−
−
Locate snubber circuit between output terminals
−
(Cs=0.022µF, Rs=47Ω)
50
−
−20
−
MAX.
25
15
0.1
120
240
Unit
IT(rms)×80%(∗)
mA
60
80
Hz
˚C
mA
mA
V
(∗) See Fig.2 about derating curve (IT(rms) vs. ambient temperature).
● Design guide
In order for the SSR to turn off, the triggering current (IF) must be 0.1mA or less.
In phase control applications or where the SSR is being by a pulse signal, please ensure that the pulse width
is a minimum of 1ms.
When the input current (IF) is below 0.1mA, the output Triac will be in the open circuit mode. However, if the
voltage across the Triac, VD, increases faster than rated dV/dt, the Triac may turn on. To avoid this situation,
please incorporate a snubber circuit. Due to the many different types of load that can be driven, we can
merely recommend some circuit values to start with : Cs=0.022µF and Rs=47Ω. The operation of the SSR
and snubber circuit should be tested and if unintentional switching occurs, please adjust the snubber circuit
component values accordingly.
When making the transition from On to Off state, a snubber circuit should be used ensure that sudden drops
in current are not accompanied by large instantaneous changes in voltage across the Triac.
This fast change in voltage is brought about by the phase difference between current and voltage.
Primarily, this is experienced in driving loads which are inductive such as motors and solenods.
Following the procedure outlined above should provide sufficient results.
Any snubber or Varistor used for the above mentioned scenarios should be located as close to the main
output triac as possible.
All pins shall be used by soldering on the board. (Socket and others shall not be used.)
● Degradation
In general, the emission of the IRED used in SSR will degrade over time.
In the case where long term operation and / or constant extreme temperature fluctuations will be applied to
the devices, please allow for a worst case scenario of 50% degradation over 5years.
Therefore in order to maintain proper operation, a design implementing these SSRs should provide at least
twice the minimum required triggering current from initial operation.
Sheet No.: D4-A00401FEN
9
PR26MF1xNSZ Series
PR36MF1xNSZ Series
● Recommended Foot Print (reference)
SMT Gullwing Lead-form
1.7
2.54
2.54
2.54
8.2
2.2
(Unit : mm)
● Standard Circuit
R1
+VCC
2
SSR
D1
3
V1
Load
8
ZS
AC Line
6
Tr1
ZS : Surge absorption circuit (Snubber circuit)
✩ For additional design assistance, please review our corresponding Optoelectronic Application Notes.
Sheet No.: D4-A00401FEN
10
PR26MF1xNSZ Series
PR36MF1xNSZ Series
■ Manufacturing Guidelines
● Soldering Method
Reflow Soldering:
Reflow soldering should follow the temperature profile shown below.
Soldering should not exceed the curve of temperature profile and time.
Please don't solder more than twice.
(˚C)
300
Terminal : 260˚C peak
( package surface : 250˚C peak)
200
Reflow
220˚C or more, 60s or less
Preheat
150 to 180˚C, 120s or less
100
0
0
1
2
3
4
(min)
Flow Soldering :
Flow soldering should be completed below 270˚C and within 10s.
Preheating is within the bounds of 100 to 150˚C and 30 to 80s.
Please don't solder more than twice.
Hand soldering
Hand soldering should be completed within 3s when the point of solder iron is below 400˚C.
Please don't solder more than twice.
Other notices
Please test the soldering method in actual condition and make sure the soldering works fine, since the impact
on the junction between the device and PCB varies depending on the tooling and soldering conditions.
Sheet No.: D4-A00401FEN
11
PR26MF1xNSZ Series
PR36MF1xNSZ Series
● Cleaning instructions
Solvent cleaning :
Solvent temperature should be 45˚C or below. Immersion time should be 3minutes or less.
Ultrasonic cleaning :
The impact on the device varies depending on the size of the cleaning bath, ultrasonic output, cleaning time,
size of PCB and mounting method of the device.
Therefore, please make sure the device withstands the ultrasonic cleaning in actual conditions in advance of
mass production.
Recommended solvent materials :
Ethyl alcohol, Methyl alcohol and Isopropyl alcohol.
In case the other type of solvent materials are intended to be used, please make sure they work fine in
actual using conditions since some materials may erode the packaging resin.
● Presence of ODC
This product shall not contain the following materials.
And they are not used in the production process for this device.
Regulation substances : CFCs, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methylchloroform)
Specific brominated flame retardants such as the PBBOs and PBBs are not used in this product at all.
Sheet No.: D4-A00401FEN
12
PR26MF1xNSZ Series
PR36MF1xNSZ Series
■ Package specification
● Sleeve package
Through-Hole
Package materials
Sleeve : HIPS (with anti-static material)
Stopper : Styrene-Elastomer
Package method
MAX. 50pcs of products shall be packaged in a sleeve.
Both ends shall be closed by tabbed and tabless stoppers.
The product shall be arranged in the sleeve with its anode mark on the tabless stopper side.
MAX. 20 sleeves in one case.
Sleeve outline dimensions
12.0
±2
5.8
10.8
520
6.7
(Unit : mm)
Sheet No.: D4-A00401FEN
13
PR26MF1xNSZ Series
PR36MF1xNSZ Series
● Tape and Reel package
SMT Gullwing
Package materials
Carrier tape : A-PET (with anti-static material)
Cover tape : PET (three layer system)
Reel : PS
Carrier tape structure and Dimensions
F
J
D
E
G
MA
X.
H
H
A
B
C
I
5˚
K
Dimensions List
A
B
16.0±0.3
7.5±0.1
H
I
10.4±0.1
0.4±0.05
C
1.75±0.1
J
4.2±0.1
D
12.0±0.1
K
10.2±0.1
E
2.0±0.1
(Unit : mm)
F
G
+0.1
4.0±0.1
φ1.5−0
Reel structure and Dimensions
e
d
c
g
Dimensions List
a
b
330
17.5±1.5
e
f
23±1.0
2.0±0.5
f
a
b
(Unit : mm)
c
d
±1.0
100
13±0.5
g
2.0±0.5
Direction of product insertion
Pull-out direction
[Packing : 1 000pcs/reel]
Sheet No.: D4-A00401FEN
14
PR26MF1xNSZ Series
PR36MF1xNSZ Series
■ Important Notices
with equipment that requires higher reliability such as:
--- Transportation control and safety equipment (i.e.,
aircraft, trains, automobiles, etc.)
--- Traffic signals
--- Gas leakage sensor breakers
--- Alarm equipment
--- Various safety devices, etc.
(iii) SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as:
--- Space applications
--- Telecommunication equipment [trunk lines]
--- Nuclear power control equipment
--- Medical and other life support equipment (e.g.,
scuba).
· The circuit application examples in this publication are
provided to explain representative applications of
SHARP devices and are not intended to guarantee any
circuit design or license any intellectual property rights.
SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices.
· Contact SHARP in order to obtain the latest device
specification sheets before using any SHARP device.
SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure,
and other contents described herein at any time without
notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice.
· If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Law of Japan, it is
necessary to obtain approval to export such SHARP devices.
· Observe the following points when using any devices
in this publication. SHARP takes no responsibility for
damage caused by improper use of the devices which
does not meet the conditions and absolute maximum
ratings to be used specified in the relevant specification
sheet nor meet the following conditions:
(i) The devices in this publication are designed for use
in general electronic equipment designs such as:
--- Personal computers
--- Office automation equipment
--- Telecommunication equipment [terminal]
--- Test and measurement equipment
--- Industrial control
--- Audio visual equipment
--- Consumer electronics
(ii) Measures such as fail-safe function and redundant
design should be taken to ensure reliability and safety
when SHARP devices are used for or in connection
· This publication is the proprietary product of SHARP
and is copyrighted, with all rights reserved. Under the
copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in
part, without the express written permission of SHARP.
Express written permission is also required before any
use of this publication may be made by a third party.
· Contact and consult with a SHARP representative if
there are any questions about the contents of this publication.
Sheet No.: D4-A00401FEN
15