Standard Products Datasheet RadHard-by-Design RHD8544 Dual 16-Channel Analog Multiplexer www.aeroflex.com/RHDseries May 14, 2015 FEATURES 32 Channels provided by two independent 16-channel multiplexers Single power supply operation at +3.3V to +5V Radiation performance - Total dose: >1Mrad(Si), Dose rate = 50 - 300 rads(Si)/s - ELDRS Immune - SEL Immune: >100 MeV-cm2/mg - Neutron Displacement Damage: >1014 neutrons/cm2 Full military temperature range Low power consumption < 11.2mW CMOS analog switching allows rail to rail operation and low switch impedance Separate address buses A(0-3) & B(0-3) and enable EN(0-15) & EN(16-31) Designed for aerospace and high reliability space applications Packaging – Hermetic ceramic - 56 leads, 0.800"Sq x 0.200"Ht quad flat pack - Weight - 6 grams max Aeroflex Plainview’s Radiation Hardness Assurance Plan is DLA Certified to MIL-PRF-38534, Appendix G. GENERAL DESCRIPTION Aeroflex’s RHD8544 is a radiation hardened, single supply, dual 16-Channel Multiplexer MCM (multi-chip module). The RHD8544 design uses specific circuit topology and layout methods to mitigate total ionization dose effects and single event latchup. These characteristics make the RHD8544 especially suited for the harsh environment encountered in Deep Space missions. It is available in a 56 lead High Temperature Co-Fired Ceramic (HTCC) Quad Flatpack (CQFP). It is guaranteed operational from -55°C to +125°C. Available screened in accordance with MIL-PRF-38534 Class K, the RHD8544 is ideal for demanding military and space applications. ORGANIZATION AND APPLICATION The RHD8544 consists of two independent 16-channel multiplexers arranged as shown in the block diagram. A Section Sixteen (16) channels addressable by bus A(0-3), enabled by EN(0-15) and outputted on Output1( 0-15). B Section Sixteen (16) channels addressable by bus B(0-3), enabled by EN(16-31) and outputted on Output2(16-31). SCD8544 Rev C SECTION A CH 0 16 • • • MUX 1 CH 15 OUTPUT1 (0-15) EN (0-15) A0 A1 A2 A3 SECTION B CH 16 16 • • • MUX 2 CH 31 OUTPUT2 (16-31) EN (16-31) B0 B1 B2 B3 +VCC GND RHD8544: DUAL 16-CHANNEL ANALOG MUX BLOCK DIAGRAM SCD8544 Rev C 5/14/15 2 Aeroflex Plainview ABSOLUTE MAXIMUM RATINGS 1/ Parameter Range Units Case Operating Temperature Range -55 to +125 °C Storage Temperature Range -65 to +150 °C +7.0 V Digital Input Over Voltage VEN0-15 (Pin 13), VEN16-31 (Pin 44), VA (Pins 14, 15, 16, 17), VB (Pins 40, 41, 42, 43) < VCC +0.4 > GND -0.4 V V Analog Input Over Voltage VIN (CH0-CH31) < VCC +0.4 > GND -0.4 V Supply Voltage +VCC (Pin 18) Notes: 1/ All measurements are made with respect to ground. NOTICE: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress rating only; functional operation beyond the "Operation Conditions" is not recommended and extended exposure beyond the "Operation Conditions" may affect device reliability. RECOMMENDED OPERATING CONDITIONS 1/ Symbol Typical Units Power Supply Voltage 3.3 to 5.0 V VIL Low Level Input Voltage 30% VCC V VIH High Level Input Voltage 70% VCC V +VCC Parameter DC ELECTRICAL PERFORMANCE CHARACTERISTICS 1/ (Tc = -55°C to +125°C, +VCC = +5V - Unless otherwise specified) Parameter Supply Current +VCC Symbol Conditions Max Units +ICC EN = 30% VCC 0 1.6 mA +ISBY EN = 70% VCC 0 400 A +25°C -5 5 nA +125°C -50 50 nA +25°C -5 5 nA +125°C -50 50 nA +25°C -5 5 nA +125°C -50 50 nA +25°C -5 5 nA +125°C -50 50 nA +25°C -5 5 nA +125°C -50 50 nA +25°C -5 5 nA +125°C -50 50 nA IAL VA = 30% VCC Address Input Current A(0-3), B(0-3) IAH IENL VA = 70% VCC VEN = 30% VCC Enable Input Current EN(0-15), EN(16-31) IENH VEN = 70%VCC High Input Leakage Current (CH0-CH31) IINLK5 VIN = +5V, VEN =70% VCC, Output and all unused MUX inputs under test = 0V Low Input Leakage Current (CH0-CH31) IINLK0 VIN = 0V, VEN =70% VCC Output and all unused MUX inputs under test = +5V SCD8544 Rev C 5/14/15 Min 3 Aeroflex Plainview DC ELECTRICAL PERFORMANCE CHARACTERISTICS 1/ (continued) (Tc = -55°C to +125°C, +VCC = +5V - Unless otherwise specified) Parameter Output Leakage Current VOUT (pins 12 & 45) Switch ON Resistance OUTPUTS (pins 12 & 45) Symbol Conditions VOUT = +5V, VEN = 70% VCC , All inputs grounded except channel being tested 3/, 4/ IOUTLK Min Max Units +25°C -5 5 nA +125°C -50 50 nA -55°C - 500 +25°C - 750 +125°C - 1000 VIN = 0V, VEN = 30% VCC IOUT = +1mA RDSON VIN = +2.5V, VIN = +5V, VEN = 30% VCC IOUT = -1mA 2/, 3/, 5/, 6/ Notes: 1/ Measure inputs sequentially. Ground all unused inputs of the device under test. VA is the applied input voltage to the address lines A(0-3). VB is the applied input voltage to the address lines B(0-3). 2/ VIN is the applied input voltage to the input channels (CH0-CH31). 3/ VEN 0-15 is the applied input voltage to the enable line EN (0-15). VEN 16-31 is the applied input voltage to the enable line EN (16-31) 4/ VOUT is the applied input voltage to the output lines OUTPUT1 (0-15), OUTPUT2 (16-31) 5/ Negative current is the current flowing out of each of the MUX pins. Positive current is the current flowing into each MUX pin. 6/ The RHD8544 cannot be operated with analog inputs below 0 volts. SWITCHING CHARACTERISTICS (Tc = -55°C to +125°C, +VCC = +5V - Unless otherwise specified) Parameter Symbol tAHL Conditions VOUT High to Low Transition Address to Output Delay tALH Enable to Output Delay SCD8544 Rev C 5/14/15 VOUT Low to High Transition tONEN VEN = 30% VCC (Enabled) tOFFEN VEN = 70% VCC (Disabled) 4 Temp Min Max Units -55°C 10 150 ns +25°C 10 150 ns +125°C 10 200 ns -55°C 10 150 ns +25°C 10 150 ns +125°C 10 200 ns -55°C 10 150 ns +25°C 10 150 ns +125°C 10 200 ns ALL 10 200 ns Aeroflex Plainview TRUTH TABLE (CH0–CH15) A3 A2 A1 A0 EN (0-15) "ON" CHANNEL, 1/ (OUTPUT 1) X X X X H NONE L L L L L CH0 L L L H L CH1 L L H L L CH2 L L H H L CH3 L H L L L CH4 L H L H L CH5 L H H L L CH6 L H H H L CH7 H L L L L CH8 H L L H L CH9 H L H L L CH10 H L H H L CH11 H H L L L CH12 H H L H L CH13 H H H L L CH14 H H H H L CH15 1/ Between (CH0-CH15) and OUTPUT1 (0-15) TRUTH TABLE (CH16–CH31) B3 B2 B1 B0 EN (16-31) "ON" CHANNEL, 2/ (OUTPUT 2) X X X X H NONE L L L L L CH16 L L L H L CH17 L L H L L CH18 L L H H L CH19 L H L L L CH20 L H L H L CH21 L H H L L CH22 L H H H L CH23 H L L L L CH24 H L L H L CH25 H L H L L CH26 H L H H L CH27 H H L L L CH28 H H L H L CH29 H H H L L CH30 H H H H L CH31 2/ Between (CH16-CH31) and OUTPUT2 (16-31) SCD8544 Rev C 5/14/15 5 Aeroflex Plainview VIH Address Lines (A0 - A3) 50% VIL VIN(CH A0-3’) Output VOUT 50% VIN(CH A0-3) t AHL VIH Address Lines (A0 - A3) 50% VIL VIN(CH A0-3’) Output VOUT 50% VIN(CH A0-3) t ALH VIH Enable Lines EN 50% VIL VIN(HIGH) Output VOUT SELECTED CHANNEL HI-Z HI-Z 50% VIN(LOW) tONEN tOFFEN NOTE: f = 10KHz, Duty cycle = 50%. RHD8544 SWITCHING DIAGRAMS SCD8544 Rev C 5/14/15 6 Aeroflex Plainview PIN NUMBERS & FUNCTIONS RHD8544 – 56 Leads Ceramic QUAD Flat Pack Pin # Function Pin # Function 1 CH0 29 CH31 2 CH1 30 CH30 3 CH2 31 CH29 4 CH3 32 CH28 5 CH4 33 CH27 6 CH5 34 CH26 7 GND 35 GND 8 GND 36 GND 9 CH6 37 CH25 10 CH7 38 CH24 11 CASE GND 39 NC 12 OUTPUT1 (0-15) 40 B3 13 EN (0-15) 41 B2 14 A0 42 B1 15 A1 43 B0 16 A2 44 EN (16-31) 17 A3 45 OUTPUT2 (16-31) 18 +VCC 46 GND 19 CH15 47 CH16 20 CH14 48 CH17 21 GND 49 GND 22 GND 50 GND 23 CH13 51 CH18 24 CH12 52 CH19 25 CH11 53 CH20 26 CH10 54 CH21 27 CH9 55 CH22 28 CH8 56 CH23 Notes: 1. It is recommended that all "NC" or "no connect pin", be grounded. This eliminates or minimizes any ESD or static buildup. 2. Package lid is internally connected to circuit ground (Pins 7, 8, 11, 21, 22, 35, 36, 46, 49, 50). SCD8544 Rev C 5/14/15 7 Aeroflex Plainview ORDERING INFORMATION Model DLA SMD # Screening Package RHD8544-7 - Commercial Flow, +25°C testing only RHD8544-S - Military Temperature, -55°C to +125°C Screened in accordance with the individual Test Methods of MIL-STD-883 for Space Applications RHD8544-201-1S 5962-1220901KXC In accordance with DLA SMD RHD8544-901-1S 5962H1220901KXC In accordance with DLA Certified RHA Program Plan to RHA Level "H", 1Mrads(Si) QUAD Flat Pack Note: Outside ceramic tie bars not shown for clarity. Contact factory for details. 0.650 ±.005 (13 Spaces at .050) Tol Non-Cum 4 Sides Pin 1 Pin 7 .200 MAX Pin 50 Pin 49 Pin 8 .0165 ±.003 0.800 SQ ±.010 Pin 21 (.650) Pin 36 Pin 35 Pin 22 .006 ±.002 FLAT PACKAGE OUTLINE EXPORT CONTROL: This product is controlled for export under the U.S. Department of Commerce (DoC). A license may be required prior to the export of this product from the United States. www.aeroflex.com/HiRel [email protected] Datasheet Definitions: Advanced Preliminary Datasheet Product in Development Shipping Non-Flight Prototypes Shipping QML and Reduced HiRel Aeroflex Plainview, Inc. reserves the right to make changes to any products and services described herein at any time without notice. Consult Aeroflex or an authorized sales representative to verify that the information in this data sheet is current before using this product. Aeroflex does not assume any responsibility or liability arising out of the application or use of any product or service described herein, except as expressly agreed to in writing by Aeroflex; nor does the purchase, lease, or use of a product or service from Aeroflex convey a license under any patent rights, copyrights, trademark rights, or any other of the intellectual rights of Aeroflex or of third parties. SCD8544 Rev C 5/14/15 8 Our passion for performance is defined by three attributes. Solution-Minded Performance-Driven Customer-Focused