REVISIONS LTR DESCRIPTION APPROVED DATE (YR-MO-DA) REV SHEET REV SHEET REV STATUS OF SHEETS PMIC N/A STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A REV SHEET 1 2 3 4 5 PREPARED BY Gary Zahn 6 7 8 9 10 11 12 13 14 DEFENSE SUPPLY CENTER COLUMBUS P. O. BOX 3990 COLUMBUS, OHIO 43216-5000 CHECKED BY Michael C. Jones APPROVED BY Kendall A. Cottongim MICROCIRCUIT, HYBRID, DIGITAL, SINGLE CHANNEL, DRIVER-RECEIVER DRAWING APPROVAL DATE 97-10-29 SIZE REVISION LEVEL A SHEET DSCC FORM 2233 APR 97 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. CAGE CODE 5962-96741 67268 1 OF 14 5962-E006-98 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes, class D (lowest reliability), class E, (exceptions), class G (lowest high reliability), class H (high reliability), and class K, (highest reliability) and a choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 01 H X A 96741 Federal stock class designator \ RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator (see 1.2.3) Case outline (see 1.2.4) Lead finish (see 1.2.5) / \/ Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. Device classes H and K RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) shall identify the circuit function as follows: Device type 01 02 Generic number ACT4455 ACT4459 Circuit function +5 V, single channel, MIL-STD-1553 transceiver (standby low) +5 V, single channel, MIL-STD-1553 transceiver (standby high) 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level as follows: Device class Device performance documentation D, E, G, H or K Certification and qualification to MIL-PRF-38534 1.2.4 Case outline(s). The case outline(s) shall be as designated in MIL-STD-1835 and as follows: Outline letter 3 Descriptive designator Terminals Package style CQCC1-N28 28 Leadless chip carrier 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. SIZE STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 5962-96741 A REVISION LEVEL SHEET 2 1.3 Absolute maximum ratings. 1/ Supply voltage range (VCC ) . . . . . . . . . . . . . . . . . . . . . . . . . . Logic input voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Receiver differential input voltage . . . . . . . . . . . . . . . . . . . . . . Driver peak output current . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power dissipation (PD): Total hybrid (standby) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Total hybrid (100% duty cycle) . . . . . . . . . . . . . . . . . . . . . . . Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . Lead temperature (soldering, 10 seconds) . . . . . . . . . . . . . . . . Junction temperature (TJ ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . Thermal resistance, junction-to-case (JC ) . . . . . . . . . . . . . . . Thermal resistance, case-to-air (CA) . . . . . . . . . . . . . . . . . . . -0.3 V dc to +7.0 V dc -0.3 V dc to +5.5 V dc 10 Vp-p +1.0 A 200 mW 2W -65(C to +150(C +300(C +135(C 5(C/W 20(C/W (still air) 1.4 Recommended operating conditions. Supply voltage range (VCC ) . . . . . . . . . . . . . . . . . . . . . . . . . . Logic input voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Receiver differential voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . Driver peak output current . . . . . . . . . . . . . . . . . . . . . . . . . . . . Maximum serial data rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Case operating temperature range (TC ) . . . . . . . . . . . . . . . . . +4.75 V dc to +5.5 V dc 0 V dc to +5.0 V dc 8.0 Vp-p 800 mA 1.0 MHz -55(C to +125(C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbook. The following specification, standards, and handbook form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solitation. SPECIFICATION DEPARTMENT OF DEFENSE MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-883 - Test Methods and Procedures for Microelectronics. MIL-STD-973 - Configuration Management. MIL-STD-1835 - Microcircuit Case Outlines. HANDBOOK DEPARTMENT OF DEFENSE MIL-HDBK-780 - Standard Microcircuit Drawings. (Unless otherwise indicated, copies of the specification, standards, and handbook are available from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. SIZE STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 5962-96741 A REVISION LEVEL SHEET 3 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturer's Quality Management (QM) plan or as designated for applicable device class. Therefore, the tests and inspections herein may not be performed for applicable device class (see MIL-PRF-38534). Futhermore, the manufacturers may take exceptions or use alternate methods to the tests and inspections herein and not perform them. However, the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. The modification in the QM plan shall not affect the form, fit, or function as described herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Timing waveform(s). The timing waveform(s) shall be as specified on figure 2. 3.2.4 Typical bus connections. The typical bus connections shall be as specified on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of Device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked as listed in QML-38534. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DSCC-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturer's product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. QUALITY ASSURANCE PROVISIONS 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. SIZE STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 5962-96741 A REVISION LEVEL SHEET 4 TABLE I. Electrical performance characteristics. Test Conditions 1/ Symbol -55(C T C +125(C unless otherwise specified Group A subgroups Device type 1, 2, 3 1, 2, 3 4, 5, 6 9,10,11 Limits Min Max Unit RECEIVER Output low voltage Output high voltage Threshold voltage Receiver delay VOL VOH VTH tDR IOL = 4.0 mA IOH = -0.4 mA 1 MHz sine wave From input zero crossing to DATA or DATA. See figure 2. 01,02 01,02 01,02 01,02 2.5 0.56 0.5 1.1 500 0.7 40.0 200.0 V V V ns RECEIVER STROBE Input low voltage Input high voltage Input low current Input high current Strobe delay VSIL VSIH ISIL ISIH tDS VSIL = 0.4 V VSIH = 2.7 V From strobe rising or falling edge to DATA or DATA. See figure 2. 1, 2, 3 1, 2, 3 1, 2, 3 9,10,11 1, 2, 3 01,02 01,02 01,02 01,02 01,02 2.0 -0.4 V V mA µA ns See footnotes at end of table. SIZE STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 5962-96741 A REVISION LEVEL SHEET 5 TABLE I. Electrical performance characteristics - Continued. Test Conditions 1/ Symbol -55(C T C +125(C unless otherwise specified Group A subgroups Device type Limits Min Max Unit TRANSMITTER Input low voltage Input high voltage Input low current Input high current Differential output voltage Differential input impedence Differential output noise Differential offset voltage Rise time Fall time Driver delay VIL VIH IIL IIH VO Zoi VON VOS tr tf tDT VIL = 0.4 V VIH = 2.7 V 356 load, see point A on figure 3. 1406 load, see point B on figue 3. 1 MHz sine wave. In accordance with MIL-STD1553B, paragraph 4.5.2.2.2.3, see figure 3. Inhibited 356 load, see point A on figure 3. 1406 load, see point B on figure 3. 356 load, see figure 2. 356 load, see figure 2. TX IN to TX OUT, see figure 2. 1, 2, 3 1, 2, 3 1, 2, 3 4, 5, 6 4, 5, 6 4, 5, 6 4, 5, 6 9,10,11 9,10,11 9,10,11 1, 2, 3 01,02 01,02 01,02 01,02 01,02 01,02 01,02 01,02 01,02 01,02 01,02 2.0 -0.4 6.5 26.0 2.0 -90.0 -360.0 100.0 100.0 0.7 40.0 9.0 36.0 10.0 +90.0 +360.0 300.0 300.0 250.0 V V mA µA VP-P k6 mVP-P mV-pk ns ns ns See footnotes at end of table. SIZE STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 5962-96741 A REVISION LEVEL SHEET 6 TABLE I. Electrical performance characteristics - Continued. Test Conditions 1/ Symbol -55(C T C +125(C unless otherwise specified Group A subgroups Device type Limits Min Max Unit TRANSMITTER INHIBIT Input low voltage Input high voltage Input low current Input high current Inhibit delay VIIL VIIH IIIL IIIH tDI-H tDI-L VIIL = 0.4 V VIIH = 2.7 V Inhibited output, see figure 2. Active output, see figure 2. 1, 2, 3 1, 2, 3 1, 2, 3 9,10,11 1, 2, 3 01,02 01,02 01,02 01,02 01,02 2.0 -0.4 0.7 40.0 450.0 250.0 V V mA µA ns POWER SUPPLY Supply current 2/ ICC1 ICC2 ICC3 ICC4 Standby, data applied, Inhibit high 25% duty cycle, 1 MHz 50% duty cycle, 1 MHz 100% duty cycle, 1 MHz 1, 2, 3 4, 5, 6 4, 5, 6 4, 5, 6 01,02 01,02 01,02 01,02 30.0 220.0 395.0 745.0 mA mA mA mA 1/ VCC = +5.0 V dc ±0.1 V dc unless otherwise specified. 2/ Use Technitrol part number 1553-45, turns ratio 1 : 2.5 or equivalent. SIZE STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 5962-96741 A REVISION LEVEL SHEET 7 Device type All Device type All Terminal number Terminal symbol Terminal number Terminal symbol 1 TX DATA OUT 15 +5 V supply 2 +5 V supply 16 Ground 3 3 +5 V supply 17 No connect 18 RX DATA IN 4 TX DATA OUT 5 TX DATA OUT 19 RX DATA IN 6 Ground 1 20 No connect 7 No connect 21 No connect 8 No connect 22 Ground 4 9 +5 V supply 23 +5 V supply 10 RX DATA OUT 24 INHIBIT 11 Strobe 25 TX DATA IN 12 No connect 26 TX DATA IN 27 Ground 2 28 TX DATA OUT 13 RX DATA OUT 14 No connect FIGURE 1. Terminal connections. SIZE STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 5962-96741 A REVISION LEVEL SHEET 8 Device type 01. NOTE: Both inputs "TX DATA IN" and "TX DATA IN" must be in the same logic states during off times. FIGURE 2. Timing waveforms. SIZE STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 5962-96741 A REVISION LEVEL SHEET 9 Device type 02. NOTE: Both inputs "TX DATA IN" and "TX DATA IN" must be in the same logic states during off times. FIGURE 2. Timing waveforms - Continued. SIZE STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 5962-96741 A REVISION LEVEL SHEET 10 NOTE: 1. Transformer is a Technitrol, part number 1553-45 or equivalent. FIGURE 3. Typical bus connections. SIZE STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 5962-96741 A REVISION LEVEL SHEET 11 TABLE II. Electrical test requirements. MIL-PRF-38534 test requirements Subgroups (in accordance with MIL-PRF-38534, group A test table) Interim electrical parameters 3, 6, 11 Final electrical parameters 1*, 2, 3, 4, 5, 6, 9, 10, 11 Group A test requirements 1, 2, 3, 4, 5, 6, 9, 10, 11 Group C end-point electrical parameters 1, 2, 3 MIL-STD-883, group E end-point electrical parameters for RHA devices Subgroups** (in accordance with method 5005, group A test table) * PDA applies to subgroup 1. ** When applicable to this standard microcircuit drawing, the subgroups shall be defined. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. b. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1015 of MIL-STD-883. (2) T C as specified in accordance with table I of method 1015 of MIL-STD-883. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. 4.3 Conformance and periodic inspections. Conformance inspection (CI) and periodic inspection (PI) shall be in accordance with MIL-PRF-38534 and as specified herein. 4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF-38534 and as follows: a. Tests shall be as specified in table II herein. b. Subgroups 7 and 8 shall be omitted. SIZE STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 5962-96741 A REVISION LEVEL SHEET 12 4.3.2 Group B inspection (PI). Group B inspection shall be in accordance with MIL-PRF-38534. 4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows: a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1005 of MIL-STD-883. (2) T C as specified in accordance with table I of method 1005 of MIL-STD-883. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 4.3.4 Group D inspection (PI). Group D inspection shall be in accordance with MIL-PRF-38534. 4.3.5 Group E inspection. Group E inspection is required only for parts intended to be marked as radiation hardness assured (see 3.5 herein). RHA levels for device classes H and K shall be M, D, R, and H. RHA quality conformance inspection sample tests shall be performed at the RHA level specified in the acquisition document. a. RHA tests for device classes H and K for levels M, D, R, and H shall be performed through each level to determine at what levels the devices meet the RHA requirements. These RHA tests shall be performed for initial qualification and after design or process changes which may affect the RHA performance of the device. b. End-point electrical parameters shall be as specified in table II herein. c. Prior to total dose irradiation, each selected sample shall be assembled in its qualified package. It shall pass the specified group A electrical parameters in table I for subgroups specified in table II herein. d. For device classes H and K, the devices shall be subjected to radiation hardness assured tests as specified in MIL-PRF-38534 for RHA level being tested, and meet the postirradiation end-point electrical parameter limits as defined in table I at T A = +25(C ±5 percent, after exposure. e. Prior to and during total dose irradiation testing, the devices shall be biased to establish a worst case condition as specified in the radiation exposure circuit. f. For device classes H and K, subgroups 1 and 2 in table V, method 5005 of MIL-STD-883 shall be tested as appropriate for device construction. g. When specified in the purchase order or contract, a copy of the RHA delta limits shall be supplied. SIZE STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 5962-96741 A REVISION LEVEL SHEET 13 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38534. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-prepared specification or drawing. 6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for the individual documents. This coordination will be accomplished in accordance with MIL-STD-973 using DD Form 1692, Engineering Change Proposal. 6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus when a system application requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-7603. 6.5 Comments. Comments on this drawing should be directed to DSCC-VA, P. O. Box 3990, Columbus, Ohio 43216-5000, or telephone (614) 692-0676. 6.6 Sources of supply for device classes H and K. Sources of supply for device classes H and K are listed in QML-38534. The vendors listed in QML-38534 have submitted a certificate of compliance (see 3.7 herein) to DSCC-VA and have agreed to this drawing. SIZE STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 5962-96741 A REVISION LEVEL SHEET 14 STANDARD MICROCIRCUIT DRAWING SOURCE APPROVAL BULLETIN DATE: 97-10-29 Approved sources of supply for SMD 5962-96741 are listed below for immediate acquisition only and shall be added to QML-38534 during the next revision. QML-38534 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DSCC-VA. This bulletin is superseded by the next dated revision of QML-38534. 1/ 2/ Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9674101H3A 5962-9674101H3C 88379 88379 ACT 4455 ACT 4455 5962-9674102H3A 5962-9674102H3C 88379 88379 ACT 4459 ACT 4459 The lead finish shown for each PIN, representing a hermetic package, is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the Vendor to determine availability. Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. Vendor CAGE number 88379 Vendor name and address Aeroflex Circuit Technology Corporation 35 South Service Road Plainview, NY 11803-4193 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in this information bulletin.