Evaluation Board User Guide UG-068 One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com Setting Up the Evaluation Board for the ADCLK948 PACKAGE LIST The data sheet contains full technical details about the specifications and operation of this device. Evaluation board with ADCLK948 component installed Applicable documents (schematic, layout) GENERAL DESCRIPTION This user guide describes how to set up and use the evaluation board for the ADCLK948. The ADCLK948 data sheet should be used in conjunction with this user guide. The ADCLK948 is a very high performance clock fanout buffer. The evaluation board is fabricated using a high quality Rogers dielectric material. Transmission line paths are kept as close to 50 Ω as possible. 08667-101 DIGITAL PICTURE OF EVALUATION BOARD Figure 1. ADCLK948 Evaluation Board Please see the last page for an important warning and disclaimers. Rev. 0 | Page 1 of 8 UG-068 Evaluation Board User Guide TABLE OF CONTENTS Package List ....................................................................................... 1 Recommended Board Setup ........................................................3 General Description ......................................................................... 1 Clock Outputs ................................................................................4 Digital Picture of Evaluation Board ............................................... 1 Evaluation Board Schematic and Artwork.....................................5 Revision History ............................................................................... 2 ESD Caution...................................................................................8 Evaluation Board Hardware ............................................................ 3 REVISION HISTORY 11/09—Revision 0: Initial Version Rev. 0 | Page 2 of 8 Evaluation Board User Guide UG-068 EVALUATION BOARD HARDWARE common-mode voltage for both inputs is provided by tying VREF1 and VT1 together. This connection is made with R14 installed at the factory. RECOMMENDED BOARD SETUP The recommended setup for the ADCLK948 evaluation board is shown in Figure 2. VCC is set to 3.3 V and VEE is set to GND. The CLKSEL jumper (P2) is provided to select the desired input configuration. The range of the peak-to-peak input voltage swing at CLK1 is 0.2 V p-p to 1.7 V p-p. Note that output jitter performance is degraded by an input slew rate, as shown in the data sheet. On the evaluation board, Input CLK0 and Input CLK0 are set up for dc-coupled operation to the ADCLK948 via J2 and J4. This input configuration requires the user to provide the appropriate ac swing and common-mode voltage to both inputs. Refer to the ADCLK948 data sheet for input specifications. Table 1. Basic Equipment Required Quantity 1 1 1 1 4 CLK1 is set up to evaluate with a single-ended source via the balun on the evaluation board. In addition, series capacitors in the path provide ac-coupled inputs to the ADCLK948. The Description Single power supply Signal source High bandwidth oscilloscope High bandwidth Differential Probe (Optional) Matched high speed cables POWER SUPPLY +3.3V GND VCC VEE CH 1 CLK1 CLK1 Qx ADCLK948 EVALUATION BOARD OSCILLOSCOPE CLK0 Qx CH 2 CLK0 VREF 1 VT1 VREF 0 VT0 Figure 2. Recommended Setup for Device Evaluation Rev. 0 | Page 3 of 8 08667-002 CLOCK SOURCE GND UG-068 Evaluation Board User Guide CLOCK OUTPUTS Table 2. Power Connections via P1 The ADCLK948 has eight differential outputs. Four of the differential clock outputs on the evaluation board are biased to GND via 200 Ω and ac-coupled to the SMAs. From the SMAs, use matched 50 Ω coaxial cables into the oscilloscope for evaluation. The other four differential outputs on the evaluation board are not launched. Use a high bandwidth differential probe and oscilloscope close to the ADCLK948 device for evaluation. See the evaluation board schematic in Figure 4 for more details. Label GND VCC VEE ADCLK948 Connect to GND Connect to 3.3 V Connect to GND LVPECL ADCLK948 Q0 Q0 Q1 Q1 Q2 Q2 Q3 VREF 0 REFERENCE Q3 Q4 VT0 Q4 CLK0 CLK0 Q5 VT1 Q5 CLK1 Q6 CLK1 Q6 Q7 IN_SEL REFERENCE Figure 3. ADCLK948 1:8 Clock/Data Buffer Block Diagram Rev. 0 | Page 4 of 8 08667-001 VREF 1 Q7 LABEL CLK1B LABEL CLK1 LABEL CLK0B CLK0 GND J3 J1 GND CLK1B CLK1 GND J2 CLK0B GND LABEL CLK0 GND 0 OUT0B C2 1 2 T2 GND R10 100 LABEL "OUTPUT 7" GND J6 GND J5 GND LABEL "OUTPUT 7B" 1 2 R09 0 DNI 4 3 MABA-007159-000000 1 SEC 5 PRI 1 2 R08 0 DNI OUT7 OUT7B 0.1UF DNI R52 49.9 DNI R51 49.9 0.1UF C4 1 2 DNI R68 0.1UF C3 1 2 DNI R67 VEE 0 0 1 2 3 VREF0 4 VT0 5 6 7 VT1 VREF1 8 VEE VEE VCC 50 OHMS 50 OHMS VEE VCC VEE VCC VEE VEE VCC VEE 0 C12 1 2 0.1UF 0 0.1UF DNI R62 0 OHMS OHMS OHMS OHMS OHMS TP12 DNI 1 OUT6B LABEL "OUTPUT 6B" R30 49.9 R29 49.9 50 OHMS TP11 DNI 1 LABEL "OUTPUT 6" OUT6 50 OHMS 50 OHMS 50 50 50 50 50 0.1UF C7 OUT1B 49.9 49.9 0 R15 R28 OUT1 OUT1B TP9 TP10 DNI DNI 1 1 DNI R64 0.1UF C6 DNI R63 C11 DNI R61 24 Q2 23 CLK0 Q2B 22 CLK0B Q3 U1 21 VREF0 Q3B 20 VT0 ADCLK948_PRELIM Q4 19 CLK1 Q4B 18 CLK1B Q5 17 VT1 Q5B VREF1 INSEL VCC CLKSEL 50 OHMS VEE 50 OHMS C03 50 OHMS 0.1UF C04 1 2 1 2 50 OHMS 50 OHMS P2 1 2 3 0.1UF LABEL "CLKSEL CONNECTS (CLKSEL)" LABEL "VEE CONNECTS (CLK0)" LABEL "VCC CONNECTS (CLK1)" GND J7 DNI R50 49.9 DNI R66 0 VEE R1 R2 GND 200 200 LABEL "OUTPUT 0" 1 J4 R07 R11 2 49.9 DNI R12 50 OHMS R19 49.9 200 DNI 0.1UF R49 49.9 50 OHMS 50 OHMS 200R7 R9 200 R18 PAD 32 31 30 29 28 27 26 25 VEE VEE VEE VEE VEE VEE DNI 4 3 2 R55 49.9 GND 0.1UF 0.1UF C14 0 0 0.1UF C18 1 2 DNI R60 0.1UF C17 DNI R59 DNI R69 0 0.1UF C13 0 0.1UF C16 1 2 DNI R58 DNI R70 0 0 0.1UF C15 1 2 DNI R57 0.1UF C9 DNI TP7 R43 DNI R54 49.9 VCC GND GND 4 3 2 R45 R46 VT0 1 VREF1 DNI TP2 VREF1 1 VT1 DNI TP4 VEE GND GND BYPASS CAPACITORS (SUPPLY) VCC VEE VREF0 VT1 1 VT0 TP3 R47 R48 BYPASS CAPACITORS VT1 VREF0 VREF1 VT0 LABEL "OUTPUT 5B" LABEL "OUTPUT 5" LABEL "OUTPUT 4B" 4 3 2 J11 1 J12 OUT5B1 OUT5 DNI R53 49.9 R44 BYPASS CAPACITORS (DUT) VEE LABEL "OUTPUT 4" DNI TP8 R17 1 49.9 OUT4B R16 49.9 1 OUT4 Z5.531.3425.0 ORDER WEILAND 25.600.5453.0 PLU LABEL "VCC" LABEL "GND" LABEL "VEE" STITCHING RESISTORS (O OHM) GND DNI TP5 GND LABEL "OUTPUT 3"VEE 1 OUT3 DNI TP1 R25 49.9 DNI 1 TP6 VREF0 LABEL "OUTPUT 3B" R27 49.9 1 OUT3B 4 3 2 DNI R56 49.9 J10 LABEL "OUTPUT 2B" OUT2B1 POWER P1 C8 LABEL "OUTPUT 2" J9 OUT2 1 DNI R71 0 DNI R72 0 VEE R26 VEE R21 200 0 R3 R4 R20 200 EPAD IN_SEL VCC_6 Q0 Q0B Q1 Q1B VCC_5 VCC_4 NC VCC_1 Q7B Q7 Q6B Q6 VCC_2 VCC_3 9 10 11 12 13 14 15 16 200 R24 200 R8 200 R22 VCC GND C31 200 200 200 200 C34 C1 1 2 200 200 C32 VEE C36 R23 1 2 3 4 VEE 0.1UF DNI R13 2 0 1 0.1UF C35 2 R14 1 10UF C33 0.1UF C38 OUT0 0.1UF LABEL "OUTPUT 0B" 08667-004 DNI R65 0.1UF 0 R5 0 200 0 0 0.1UF C37 C5 0.1UF C41 10UF 0.1UF C39 10UF 0 Rev. 0 | Page 5 of 8 R6 0.1UF C40 0 Figure 4. ADCLK948 Evaluation Board Schematic 0.1UF C42 0 J8 Evaluation Board User Guide UG-068 EVALUATION BOARD SCHEMATIC AND ARTWORK Evaluation Board User Guide 08667-005 UG-068 08667-006 Figure 5. Top Trace Layer Figure 6. Ground Plane Layer Rev. 0 | Page 6 of 8 UG-068 08667-007 Evaluation Board User Guide 08667-008 Figure 7. VCC and VEE Power Plane Layer Figure 8. Bottom Trace Layer Rev. 0 | Page 7 of 8 UG-068 Evaluation Board User Guide NOTES ESD CAUTION Evaluation boards are only intended for device evaluation and not for production purposes. Evaluation boards are supplied “as is” and without warranties of any kind, express, implied, or statutory including, but not limited to, any implied warranty of merchantability or fitness for a particular purpose. No license is granted by implication or otherwise under any patents or other intellectual property by application or use of evaluation boards. Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Analog Devices reserves the right to change devices or specifications at any time without notice. Trademarks and registered trademarks are the property of their respective owners. Evaluation boards are not authorized to be used in life support devices or systems. ©2009 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. UG08667-0-11/09(0) Rev. 0 | Page 8 of 8