Standard Reflow Profile for Standard and Lead-Free Packages The reflow here in provided is for reference only. Users are advised to optimize their own board level parameters to get proper reflow outcome. Per package qualification maximum number of reflow can be done on Microsemi® SoC Products Group packages is 3. Table 1 • SnPb Eutectic Process – Classification Temperature (TC) Volume mm3 <350 Volume mm3 350 <2.5 mm 235 + 0/–5°C 225 + 0/–5°C ³2.5 mm 225 + 0/–5°C 225 + 0/–5°C Package Thickness Table 2 • Pb-Free Process – Classification Temperature (TC) Volume mm3 <350 Volume mm3 350–2,000 Volume mm3 >2,000 <1.6 mm 260 + 0°C 1 260 + 0°C 1 260 + 0°C 1 1.6 mm – 2.5 mm 260 + 0°C 1 250 + 0°C 1 245 + 0°C 1 >2.5 mm 250 + 0°C 1 245 + 0°C 1 245 + 0°C 1 Package Thickness Notes: 1. Tolerance: The device manufacturer/supplier shall assure process compatibility up to and including the stated classification temperature at the rated MSL level (this means peak reflow temperature + 0°C. For example, 260°C +0°C). 2. At the discretion of the device manufacturer, but not the board assembler/user, the maximum peak package body temperature (Tp) can exceed the values specified in Table 2 and Table 3 on page 2. The use of a higher Tp does not change the classification temperature (TC). 3. Package volume excludes external terminals (balls, bumps, lands, leads) and/or nonintegral heat sinks. 4. The maximum component temperature reached during reflow depends on package thickness and volume. The use of convection reflow processes reduces the thermal gradients between packages. However, thermal gradients due to differences in thermal mass of SMD packages may still exist. 5. Moisture sensitivity levels of components intended for use in a Pb-free assembly process shall be evaluated using the Pb-free classification temperatures and profiles defined in Table 2 and Table 3 on page 2, whether or not Pbfree. 6. SMD packages classified to a given moisture sensitivity level by using Procedures or Criteria defined within any previous version of J-STD-020, JESD22-A112 (rescinded), IPC-SM-786 (rescinded) do not need to be reclassified to the current revision unless a change in classification level or a higher peak classification temperature is desired. April 2012 © 2012 Microsemi Corporation 1 Standard Reflow Profile for Standard and Lead-Free Packages Table 3 • Classification Reflow Profile Profile Feature Sn-Pb Eutectic Assembly Pb-Free Assembly 100°C 150°C 60–120 seconds 150°C 200°C 60–120 seconds 3°C/second maximum 3°C/second maximum 183°C 60–150 seconds 217°C 60–150 seconds See classification temperature in Table 1 on page 1. See classification temperature in Table 2 on page 1. Time (tp) 2 within 5°C of the specified classification temperature (TC) 20 2 seconds 30 2 seconds Average ramp-down rate (Tp to Tsmax) 6°C/second maximum 6°C/second maximum 6 minutes maximum 8 minutes maximum Preheat and Soak Temperature minimum (Tsmin) Temperature maximum (Tsmax) Time (Tsmin to Tsmax) (ts) Average ramp-up rate (Tsmax to Tp) Liquidous temperature (TL) Time at liquidous (tL) Peak package body temperature (Tp) 1 Time 25°C to peak temperature Notes: 1. Tolerance for peak profile temperature (Tp) is defined as a supplier minimum and a user maximum. 2. Tolerance for time at peak profile temperature (tp) is defined as a supplier minimum and a user maximum. 3. All temperatures refer to the center of the package, measured on the package body surface that is facing up during assembly reflow (e.g., live-bug). If parts are reflowed in other than the normal live-bug assembly reflow orientation (i.e., dead-bug), Tp shall be within ± 2°C of the live-bug Tp and still meet the To requirements. Otherwise, the profile shall be adjusted to achieve the latter. To accurately measure actual peak package body temperatures, refer to JEP140 for recommended thermocouple use. 4. Reflow profiles in this document are for classification/preconditioning and are not meant to specify board assembly profiles. Actual board assembly profiles should be developed based on specific process needs and board designs and should not exceed the parameters in Table 3. For example, if To is 260°C and time tp is 30 seconds, this means the following for the supplier and the user. For a supplier: The peak temperature must be at least 260°C. The time above 255°C must be at least 30 seconds. For a user: The peak temperature must not exceed 260°C. The time above 255°C must not exceed 30 seconds. 5. All components in the test load shall meet the classification profile requirements. 6. SMD packages classified to a given moisture sensitivity level by using Procedures or Criteria defined within any previous version of J-STD-020, JESD22-A112 (rescinded), IPC-SM-786 (rescinded) do not need to be reclassified to the current revision unless a change in classification level or a higher peak classification temperature is desired. 2 List of Changes User Tp < TC Supplier Tp > TC Tc Tc –5°C Supplier tp User tp Tp tp Max. Ramp-Up Rate = 3°C/s Max. Ramp-Down Rate = 6°C/s Temperature TL Tc –5°C t Tsmax Preheat Area Tsmin tS 25 Time 25°C to Peak Time Figure 1: Reflow Profile List of Changes The following table lists critical changes that were made in each revision of the document. Revision* Revision 5 (April 2012) Changes Added note above Table 1 (SAR 30886). Page 1 Note: *The revision number is located in the part number after the hyphen. The part number is displayed at the bottom of the last page of the document. The digits following the slash indicate the month and year of publication. 3 Microsemi Corporation (NASDAQ: MSCC) offers a comprehensive portfolio of semiconductor solutions for: aerospace, defense and security; enterprise and communications; and industrial and alternative energy markets. Products include high-performance, high-reliability analog and RF devices, mixed signal and RF integrated circuits, customizable SoCs, FPGAs, and complete subsystems. Microsemi is headquartered in Aliso Viejo, Calif. Learn more at www.microsemi.com. Microsemi Corporate Headquarters One Enterprise, Aliso Viejo CA 92656 USA Within the USA: +1 (949) 380-6100 Sales: +1 (949) 380-6136 Fax: +1 (949) 215-4996 © 2012 Microsemi Corporation. All rights reserved. Microsemi and the Microsemi logo are trademarks of Microsemi Corporation. All other trademarks and service marks are the property of their respective owners. 51700033-5/04.12