ADuM1200-EP Data Sheet

Dual-Channel Digital Isolator
ADuM1200-EP
Data Sheet
FEATURES
GENERAL DESCRIPTION
Narrow body, 8-lead SOIC package
Low power operation
5 V operation
1.1 mA per channel maximum at 0 Mbps to 2 Mbps
3.7 mA per channel maximum at 10 Mbps
8.2 mA per channel maximum at 25 Mbps
3 V operation
0.8 mA per channel maximum at 0 Mbps to 2 Mbps
2.2 mA per channel maximum at 10 Mbps
4.8 mA per channel maximum at 25 Mbps
Precise timing characteristics
High common-mode transient immunity: >25 kV/µs
Safety and regulatory approvals
UL recognition
2500 V rms for 1 minute per UL 1577
CSA Component Acceptance Notice #5A
VDE Certificate of Conformity
DIN V VDE V 0884-10 (VDE V 0884-10): 2006-12
VIORM = 560 V peak
The ADuM1200-EP1 is a dual-channel, digital isolator based on
the Analog Devices, Inc., iCoupler® technology. Combining
high speed CMOS and monolithic transformer technologies,
this isolation component provides outstanding performance
characteristics superior to alternatives, such as optocouplers.
By avoiding the use of LEDs and photodiodes, iCoupler devices
remove the design difficulties commonly associated with optocouplers. The typical optocoupler concerns regarding uncertain
current transfer ratios, nonlinear transfer functions, and temperature and lifetime effects are eliminated with the simple
iCoupler digital interfaces and stable performance characteristics.
The need for external drivers and other discrete components is
eliminated with these iCoupler products. Furthermore, iCoupler
devices consume one-tenth to one-sixth the power of optocouplers
at comparable signal data rates.
The ADuM1200-EP isolator provides two independent isolation
channels with a supply voltage on either side ranging from 3.0 V
to 5.5 V. In addition, the ADuM1200-EP provides low pulse width
distortion and tight channel-to-channel matching. Unlike other
optocoupler alternatives, the ADuM1200-EP isolator has a
patented refresh feature that ensures dc correctness in the absence
of input logic transitions and during power-up/ power-down
conditions.
ENHANCED PRODUCT FEATURES
Supports defense and aerospace applications (AQEC)
Military temperature range (−55°C to +125°C)
Controlled manufacturing baseline
Enhanced product change notification
Qualification data available on request
Full details about this enhanced product are available in the
ADuM1200/ADuM1201 data sheet, which should be consulted
in conjunction with this data sheet.
APPLICATIONS
Size-critical multichannel isolation
SPI interface/data converter isolation
RS-232/RS-422/RS-485 transceiver isolation
Digital field bus isolation
VDD1 1
8
VDD2
VIA 2
ENCODE
DECODE
7
VOA
VIB 3
ENCODE
DECODE
6
VOB
5
GND2
GND1 4
09201-001
FUNCTIONAL BLOCK DIAGRAM
Figure 1.
1
Protected by U.S. Patents 5,952,849; 6,873,065; 6,903,578; and 7,075,329. Other patents are pending.
Rev. B
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2010–2014 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADuM1200-EP
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Regulatory Information ................................................................8
Enhanced Product Features ............................................................ 1
Insulation and Safety-Related Specifications .............................8
Applications ....................................................................................... 1
General Description ......................................................................... 1
DIN V VDE V 0884-10 (VDE V 0884-10): 2006-12
Insulation Characteristics ............................................................9
Functional Block Diagram .............................................................. 1
Recommended Operating Conditions .......................................9
Revision History ............................................................................... 2
Absolute Maximum Ratings ......................................................... 10
Specifications..................................................................................... 3
ESD Caution................................................................................ 10
Electrical Characteristics—5 V operation................................. 3
Pin Configuration and Function Descriptions........................... 11
Electrical Characteristics—3 V operation................................. 5
Typical Performance Characteristics ........................................... 12
Electrical Characteristics—Mixed 5 V/3 V or 3 V/5 V
Operation....................................................................................... 6
Outline Dimensions ....................................................................... 13
Ordering Guide .......................................................................... 13
Package Characteristics ............................................................... 8
REVISION HISTORY
2/14—Rev. A to Rev. B
Changed +105°C to +125°C in Operating Temperature
Range ............................................................................... Throughout
Changed Minimum VDDx from 2.7 V to 3.0 V ........... Throughout
Changes to Table 6 ............................................................................ 8
Changes to Table 7 ............................................................................ 9
Changes to Table 10 ........................................................................ 10
5/12—Rev. 0 to Rev. A
Removed RoHS-Compliant from Features Section .................... 1
Changed ADuM1200WSRZ55 to ADuM1200UR-EP, Table 5... 8
Changes to Ordering Guide .......................................................... 13
7/10—Revision 0: Initial Version
Rev. B | Page 2 of 16
Data Sheet
ADuM1200-EP
SPECIFICATIONS
ELECTRICAL CHARACTERISTICS—5 V OPERATION
All voltages are relative to their respective ground; 4.5 V ≤ VDD1 ≤ 5.5 V, 4.5 V ≤ VDD2 ≤ 5.5 V; all minimum/maximum specifications apply
over the entire recommended operating range, unless otherwise noted; all typical specifications are at TA = 25°C, VDD1 = VDD2 = 5 V.
Table 1.
Parameter
DC SPECIFICATIONS
Input Supply Current per
Channel, Quiescent
Output Supply Current per
Channel, Quiescent
Total Supply Current, Two
Channels1
DC to 2 Mbps
VDD1 Supply Current
VDD2 Supply Current
10 Mbps
VDD1 Supply Current
VDD2 Supply Current
25 Mbps
VDD1 Supply Current
VDD2 Supply Current
Input Currents
Logic High Input Threshold
Logic Low Input Threshold
Logic High Output
Voltages
Logic Low Output Voltages
SWITCHING SPECIFICATIONS
Minimum Pulse Width 2
Maximum Data Rate 3
Propagation Delay 4
Pulse Width Distortion,
|tPLH − tPHL|4
Propagation Delay Skew 5
Channel-to-Channel
Matching 6
Output Rise/Fall Time
(10% to 90%)
Common-Mode Transient
Immunity
Logic High Output7
Logic Low Output7
Refresh Rate
Symbol
Min
Typ
Max
Unit
IDDI (Q)
0.50
0.60
mA
IDDO (Q)
0.19
0.30
mA
IDD1 (Q)
1.1
1.4
mA
IDD2 (Q)
0.5
0.8
mA
IDD1 (Q)
IDD2 (Q)
4.3
1.3
5.5
2.0
mA
mA
5 MHz logic signal frequency
5 MHz logic signal frequency
IDD1 (Q)
IDD2 (Q)
IIA, IIB
VIH
VIL
VOAH, VOBH
10
2.8
+0.01
13
3.4
+10
mA
mA
µA
V
V
V
12.5 MHz logic signal frequency
12.5 MHz logic signal frequency
V
V
V
V
IOx = −4 mA, VIx = VIxH
IOx = 20 µA, VIx = VIxL
IOx = 400 µA, VIx = VIxL
IOx = 4 mA, VIx = VIxL
−10
0.7 (VDD1 or VDD2)
0.3 (VDD1 or VDD2)
(VDD1 or VDD2) − 0.1
5.0
(VDD1 or VDD2) − 0.5
4.8
0.0
0.04
0.2
VOAL, VOBL
PW
tPHL, tPLH
PWD
25
20
20
50
tPSK
tPSKCD/tPSKOD
tR/tF
0.1
0.1
0.4
40
45
3
ns
Mbps
ns
ns
15
3
ns
ns
2.5
ns
|CMH|
25
35
kV/µs
|CML|
25
35
kV/µs
1.2
Mbps
fr
Rev. B | Page 3 of 16
Test Conditions
DC to 1 MHz logic signal
frequency
DC to 1 MHz logic signal
frequency
IOx = −20 µA, VIx = VIxH
VIx = VDD1, VDD2, VCM = 1000 V,
transient magnitude = 800 V
VIx = 0 V, VCM = 1000 V,
transient magnitude = 800 V
ADuM1200-EP
Parameter
Dynamic Supply Current per
Channel 8
Input
Output
Data Sheet
Symbol
Min
Typ
IDDI (D)
0.19
IDDO (D)
0.05
Max
Unit
Test Conditions
mA/
Mbps
mA/
Mbps
The supply current values are for both channels combined when running at identical data rates. Output supply current values are specified with no output load present.
The minimum pulse width is the shortest pulse width at which the specified pulse width distortion is guaranteed.
3
The maximum data rate is the fastest data rate at which the specified pulse width distortion is guaranteed.
4
tPHL propagation delay is measured from the 50% level of the falling edge of the VIx signal to the 50% level of the falling edge of the VOx signal. tPLH propagation delay is
measured from the 50% level of the rising edge of the VIx signal to the 50% level of the rising edge of the VOx signal.
5
tPSK is the magnitude of the worst-case difference in tPHL and/or tPLH that is measured between units at the same operating temperature, supply voltages, and output
load within the recommended operating conditions.
6
Codirectional channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels with inputs on the same side of
the isolation barrier. Opposing directional channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels with
inputs on opposing sides of the isolation barrier.
7
CMH is the maximum common-mode voltage slew rate that can be sustained while maintaining VOx > 0.8 VDD2. CML is the maximum common-mode voltage slew rate
that can be sustained while maintaining VOx < 0.8 V. The common-mode voltage slew rates apply to both rising and falling common-mode voltage edges. The
transient magnitude is the range over which the common mode is slewed.
8
Dynamic supply current is the incremental amount of supply current required for a 1 Mbps increase in the signal data rate.
1
2
Rev. B | Page 4 of 16
Data Sheet
ADuM1200-EP
ELECTRICAL CHARACTERISTICS—3 V OPERATION
All voltages are relative to their respective ground; 3.0 V ≤ VDD1 ≤ 3.6 V, 3.0 V ≤ VDD2 ≤ 3.6 V; all minimum/maximum specifications apply
over the entire recommended operating range, unless otherwise noted; all typical specifications are at TA = 25°C, VDD1 = VDD2 = 3 V.
Table 2.
Parameter
DC SPECIFICATIONS
Input Supply Current per Channel,
Quiescent
Output Supply Current per Channel,
Quiescent
Total Supply Current, Two Channels 1
DC to 2 Mbps
VDD1 Supply Current
VDD2 Supply Current
10 Mbps
VDD1 Supply Current
VDD2 Supply Current
25 Mbps
VDD1 Supply Current
VDD2 Supply Current
Input Currents
Logic High Input Threshold
Logic Low Input Threshold
Logic High Output Voltages
Logic Low Output Voltages
SWITCHING SPECIFICATIONS
Minimum Pulse Width 2
Maximum Data Rate 3
Propagation Delay 4
Pulse Width Distortion, |tPLH − tPHL|4
Propagation Delay Skew 5
Channel-to-Channel Matching 6
Output Rise/Fall Time (10% to 90%)
Common-Mode Transient Immunity
Logic High Output 7
Logic Low Output7
Refresh Rate
Dynamic Supply Current per Channel 8
Input
Output
Symbol
Min
Typ
Max
Unit
IDDI (Q)
0.26
0.35
mA
IDDO (Q)
0.11
0.20
mA
IDD1 (Q)
IDD2 (Q)
0.6
0.2
1.0
0.6
mA
mA
DC to 1 MHz logic signal frequency
DC to 1 MHz logic signal frequency
IDD1 (Q)
IDD2 (Q)
2.2
0.7
3.4
1.1
mA
mA
5 MHz logic signal frequency
5 MHz logic signal frequency
IDD1 (Q)
IDD2 (Q)
IIA, IIB
VIH
VIL
VOAH, VOBH
5.2
1.5
+0.01
7.7
2.0
+10
mA
mA
µA
V
V
V
V
V
V
V
12.5 MHz logic signal frequency
12.5 MHz logic signal frequency
−10
0.7 (VDD1 or VDD2)
0.3 (VDD1 or VDD2)
(VDD1 or VDD2) − 0.1
(VDD1 or VDD2) − 0.5
VOAL, VOBL
PW
tPHL, tPLH
PWD
tPSK
tPSKCD/tPSKOD
tR/tF
25
20
3.0
2.8
0.0
0.04
0.2
20
50
0.1
0.1
0.4
40
2.5
ns
Mbps
ns
ns
ns
ns
ns
55
3
16
3
|CMH|
25
35
kV/µs
|CML|
25
35
kV/µs
fr
1.1
Mbps
IDDI (D)
0.10
IDDO (D)
0.03
mA/
Mbps
mA/
Mbps
Test Conditions
IOx = −20 µA, VIx = VIxH
IOx = −4 mA, VIx = VIxH
IOx = 20 µA, VIx = VIxL
IOx = 400 µA, VIx = VIxL
IOx = 4 mA, VIx = VIxL
VIx = VDD1, VDD2, VCM = 1000 V,
transient magnitude = 800 V
VIx = 0 V, VCM = 1000 V,
transient magnitude = 800 V
The supply current values are for both channels combined when running at identical data rates. Output supply current values are specified with no output load present.
The minimum pulse width is the shortest pulse width at which the specified pulse width distortion is guaranteed.
The maximum data rate is the fastest data rate at which the specified pulse width distortion is guaranteed.
4
tPHL propagation delay is measured from the 50% level of the falling edge of the VIx signal to the 50% level of the falling edge of the VOx signal. tPLH propagation delay is
measured from the 50% level of the rising edge of the VIx signal to the 50% level of the rising edge of the VOx signal.
5
tPSK is the magnitude of the worst-case difference in tPHL and/or tPLH that is measured between units at the same operating temperature, supply voltages, and output
load within the recommended operating conditions.
6
Codirectional channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels with inputs on the same side of
the isolation barrier. Opposing directional channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels with
inputs on opposing sides of the isolation barrier.
7
CMH is the maximum common-mode voltage slew rate that can be sustained while maintaining VOx > 0.8 VDD2. CML is the maximum common-mode voltage slew rate
that can be sustained while maintaining VOx < 0.8 V. The common-mode voltage slew rates apply to both rising and falling common-mode voltage edges. The
transient magnitude is the range over which the common mode is slewed.
8
Dynamic supply current is the incremental amount of supply current required for a 1 Mbps increase in the signal data rate.
1
2
3
Rev. B | Page 5 of 16
ADuM1200-EP
Data Sheet
ELECTRICAL CHARACTERISTICS—MIXED 5 V/3 V OR 3 V/5 V OPERATION
All voltages are relative to their respective ground; 5 V/3 V operation: 4.5 V ≤ VDD1 ≤ 5.5 V, 3.0 V ≤ VDD2 ≤ 3.6 V. 3 V/5 V operation: 3.0 V
≤ VDD1 ≤ 3.6 V, 4.5 V ≤ VDD2 ≤ 5.5 V; all minimum/maximum specifications apply over the entire recommended operating range, unless
otherwise noted; all typical specifications are at TA = 25°C, VDD1 = 3.0 V, VDD2 = 5.0 V; or VDD1 = 5.0 V, VDD2 = 3.0 V.
Table 3.
Parameter
DC SPECIFICATIONS
Input Supply Current per Channel,
Quiescent
5 V/3 V Operation
3 V/5 V Operation
Output Supply Current per Channel,
Quiescent
5 V/3 V Operation
3 V/5 V Operation
Total Supply Current, Two Channels 1
DC to 2 Mbps
VDD1 Supply Current
5 V/3 V Operation
3 V/5 V Operation
VDD2 Supply Current
5 V/3 V Operation
3 V/5 V Operation
10 Mbps
VDD1 Supply Current
5 V/3 V Operation
3 V/5 V Operation
VDD2 Supply Current
5 V/3 V Operation
3 V/5 V Operation
25 Mbps
VDD1 Supply Current
5 V/3 V Operation
3 V/5 V Operation
VDD2 Supply Current
5 V/3 V Operation
3 V/5 V Operation
Input Currents
Logic High Input Threshold
Logic Low Input Threshold
Logic High Output Voltages
Logic Low Output Voltages
SWITCHING SPECIFICATIONS
Minimum Pulse Width 2
Maximum Data Rate 3
Propagation Delay 4
Pulse Width Distortion, |tPLH − tPHL|4
Propagation Delay Skew 5
Channel-to-Channel Matching 6
Output Rise/Fall Time (10% to 90%)
5 V/3 V Operation
3 V/5 V Operation
Symbol
Min
Typ
Max
Unit
Test Conditions
0.50
0.26
0.6
0.35
mA
mA
0.11
0.19
0.20
0.25
mA
mA
1.1
0.6
1.4
1.0
mA
mA
DC to 1 MHz logic signal frequency
DC to 1 MHz logic signal frequency
0.2
0.5
0.6
0.8
mA
mA
DC to 1 MHz logic signal frequency
DC to 1 MHz logic signal frequency
4.3
2.2
5.5
3.4
mA
mA
5 MHz logic signal frequency
5 MHz logic signal frequency
0.7
1.3
1.1
2.0
mA
mA
5 MHz logic signal frequency
5 MHz logic signal frequency
10
5.2
13
7.7
mA
mA
12.5 MHz logic signal frequency
12.5 MHz logic signal frequency
1.5
2.8
+0.01
2.0
3.4
+10
mA
mA
µA
V
V
V
V
V
V
V
12.5 MHz logic signal frequency
12.5 MHz logic signal frequency
IDDI (Q)
IDDO (Q)
IDD1 (Q)
IDD2 (Q)
IDD1 (Q)
IDD2 (Q)
IDD1 (Q)
IDD2 (Q)
IIA ,IIB
VIH
VIL
VOAH, VOBH
−10
0.7 (VDD1 or VDD2)
0.3 (VDD1 or VDD2)
(VDD1 or VDD2) − 0.1
(VDD1 or VDD2) − 0.5
VOAL, VOBL
PW
tPHL, tPLH
PWD
tPSK
tPSKCD/tPSKOD
tR/tF
25
20
3.0
2.8
0.0
0.04
0.2
20
50
0.1
0.1
0.4
40
50
3
15
3
3.0
2.5
Rev. B | Page 6 of 16
ns
Mbps
ns
ns
ns
ns
ns
ns
IOx = −20 µA, VIx = VIxH
IOx = −4 mA, VIx = VIxH
IOx = 20 µA, VIx = VIxL
IOx = 400 µA, VIx = VIxL
IOx = 4 mA, VIx = VIxL
Data Sheet
Parameter
Common-Mode Transient Immunity
Logic High Output 7
Logic Low Output7
Refresh Rate
5 V/3 V Operation
3 V/5 V Operation
Input Dynamic Supply Current per
Channel 8
5 V/3 V Operation
ADuM1200-EP
Symbol
Min
Typ
|CMH|
25
|CML|
25
3 V/5 V Operation
Unit
Test Conditions
35
kV/µs
35
kV/µs
VIx = VDD1, VDD2, VCM = 1000 V,
transient magnitude = 800 V
VIx = 0 V, VCM = 1000 V,
transient magnitude = 800 V
1.2
1.1
Mbps
Mbps
0.19
mA/
Mbps
mA/
Mbps
fr
IDDI (D)
3 V/5 V Operation
Output Dynamic Supply Current per
Channel8
5 V/3 V Operation
Max
0.10
IDDO(D)
0.03
0.05
mA/
Mbps
mA/
Mbps
The supply current values are for both channels combined when running at identical data rates. Output supply current values are specified with no output load present.
The minimum pulse width is the shortest pulse width at which the specified pulse width distortion is guaranteed.
3
The maximum data rate is the fastest data rate at which the specified pulse width distortion is guaranteed.
4
tPHL propagation delay is measured from the 50% level of the falling edge of the VIx signal to the 50% level of the falling edge of the VOx signal. tPLH propagation delay is
measured from the 50% level of the rising edge of the VIx signal to the 50% level of the rising edge of the VOx signal.
5
tPSK is the magnitude of the worst-case difference in tPHL and/or tPLH that is measured between units at the same operating temperature, supply voltages, and output
load within the recommended operating conditions.
6
Codirectional channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels with inputs on the same side of
the isolation barrier. Opposing directional channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels with
inputs on opposing sides of the isolation barrier.
7
CMH is the maximum common-mode voltage slew rate that can be sustained while maintaining VOx > 0.8 VDD2. CML is the maximum common-mode voltage slew rate
that can be sustained while maintaining VOx < 0.8 V. The common-mode voltage slew rates apply to both rising and falling common-mode voltage edges. The
transient magnitude is the range over which the common mode is slewed.
8
Dynamic supply current is the incremental amount of supply current required for a 1 Mbps increase in the signal data rate.
1
2
Rev. B | Page 7 of 16
ADuM1200-EP
Data Sheet
PACKAGE CHARACTERISTICS
Table 4.
Parameter
Resistance (Input-to-Output) 1
Capacitance (Input-to-Output)1
Input Capacitance
IC Junction-to-Case Thermal Resistance, Side 1
Symbol
RI-O
CI-O
CI
θJCI
IC Junction-to-Case Thermal Resistance, Side 2
θJCO
1
Min
Typ
1012
1.0
4.0
46
Max
41
Unit
Ω
pF
pF
°C/W
Test Conditions
f = 1 MHz
Thermocouple located at
center of package underside
°C/W
The device is considered a 2-terminal device; Pin 1, Pin, 2, Pin 3, and Pin 4 are shorted together, and Pin 5, Pin 6, Pin 7, and Pin 8 are shorted together.
REGULATORY INFORMATION
The ADuM1200-EP is approved by the organizations listed in Table 5. See Table 10 for details regarding recommended maximum
working voltages for specific cross-isolation waveforms and insulation levels.
Table 5.
UL
Recognized Under 1577 Component
Recognition Program 1
Single/Basic 2500 V rms Isolation Voltage
File E214100
1
2
CSA
Approved under CSA Component Acceptance
Notice #5A
Basic insulation per CSA 60950-1-03 and
IEC 60950-1, 400 V rms (566 peak) maximum
working voltage
Functional insulation per CSA 60950-1-03 and
IEC 60950-1, 800 V rms (1131 V peak) maximum
working voltage
File 205078
VDE
Certified according to DIN V VDE
V 0884-10 (VDE V 0884-10): 2006-12 2
Reinforced insulation, 560 V peak
File 2471900-4880-0001
In accordance with UL 1577, each ADuM1200UR-EP is proof tested by applying an insulation test voltage ≥ 3000 V rms for 1 second (current leakage detection
limit = 5 µA).
In accordance with DIN V VDE V 0884-10, each ADuM1200UR-EP is proof tested by applying an insulation test voltage ≥1050 V peak for 1 second (partial discharge
detection limit = 5 pC). The * marking branded on the component designates DIN V VDE V 0884-10 approval.
INSULATION AND SAFETY-RELATED SPECIFICATIONS
Table 6.
Parameter
Rated Dielectric Insulation Voltage
Clearance in the Plane of the PCB
Symbol
CLPCB
Value
2500
4.5
Unit
V rms
mm min
Minimum External Air Gap (Clearance)
L(I01)
4.0
mm min
Minimum External Tracking (Creepage)
L(I02)
4.0
mm min
Minimum Internal Gap (Internal Clearance)
Tracking Resistance (Comparative Tracking Index)
Isolation Group
CTI
0.017
>400
II
mm min
V
Rev. B | Page 8 of 16
Conditions
1 minute duration
Measured from input terminals to output terminals,
shortest line of sight distance through air in the
plane of the PCB
Measured from input terminals to output terminals,
shortest distance through air
Measured from input terminals to output terminals,
shortest distance path along body
Insulation distance through insulation
DIN IEC 112/VDE 0303 Part 1
Material Group (DIN VDE 0110, 1/89, Table 1)
Data Sheet
ADuM1200-EP
DIN V VDE V 0884-10 (VDE V 0884-10): 2006-12 INSULATION CHARACTERISTICS
This isolator is suitable for reinforced isolation within the safety limit data only. Maintenance of the safety data is ensured by protective
circuits. Note that the * marking on the package denotes DIN V VDE V 0884-10 approval for a 560 V peak working voltage.
Table 7.
Description
Installation Classification per DIN VDE 0110
For Rated Mains Voltage ≤ 150 V rms
For Rated Mains Voltage ≤ 300 V rms
For Rated Mains Voltage ≤ 400 V rms
Climatic Classification
Pollution Degree per DIN VDE 0110, Table 1
Maximum Working Insulation Voltage
Input-to-Output Test Voltage, Method B1
Input-to-Output Test Voltage, Method A
After Environmental Tests Subgroup 1
After Input and/or Safety Test Subgroup 2
and Subgroup 3
Highest Allowable Overvoltage
Safety-Limiting Values
Case Temperature
Side 1 Current
Side 2 Current
Insulation Resistance at TS
Conditions
VIORM × 1.875 = VPR, 100% production test,
tm = 1 second, partial discharge < 5 pC
VIORM × 1.6 = VPR, tm = 60 seconds,
partial discharge < 5 pC
VIORM × 1.2 = VPR, tm = 60 seconds,
partial discharge < 5 pC
Transient overvoltage, tTR = 10 seconds
Maximum value allowed in the event of a failure
(see Figure 2)
VIO = 500 V
Characteristic
Unit
VIORM
VPR
I to IV
I to III
I to II
40/125/21
2
560
1050
V peak
V peak
896
672
V peak
V peak
VTR
4000
V peak
TS
IS1
IS2
RS
150
160
170
>109
°C
mA
mA
Ω
VPR
RECOMMENDED OPERATING CONDITIONS
200
180
Table 8.
160
Parameter
Operating Temperature (TA)
Supply Voltages (VDD1, VDD2) 1
Input Signal Rise and Fall Times
140
SIDE 2
SIDE 1
120
100
1
80
40
20
0
0
50
100
150
CASE TEMPERATURE (°C)
200
Rating
−55°C to +125°C
3.0 V to 5.5 V
1.0 ms
All voltages are relative to their respective ground.
60
09201-002
SAFETY-LIMITING CURRENT (mA)
Symbol
Figure 2. Thermal Derating Curve, Dependence of SafetyLimiting Values on Case Temperature per DIN V VDE V 0884-10
Rev. B | Page 9 of 16
ADuM1200-EP
Data Sheet
ABSOLUTE MAXIMUM RATINGS
Ambient temperature = 25°C, unless otherwise noted.
Table 9.
Parameter
Storage Temperature (TST)
Ambient Operating Temperature (TA)
Supply Voltages (VDD1, VDD2) 1
Input Voltages (VIA, VIB)1, 2
Output Voltages (VOA, VOB)1, 2
Average Output Current per Pin (IO) 3
Common-Mode Transients (CML, CMH)4
Rating
−55°C to +150°C
−55°C to +125°C
−0.5 V to +7.0 V
−0.5 V to VDDI + 0.5 V
−0.5 V to VDDO + 0.5 V
−11 mA to +11 mA
−100 kV/µs to +100 kV/µs
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
All voltages are relative to their respective ground.
VDDI and VDDO refer to the supply voltages on the input and output sides of a
given channel, respectively.
3
See Figure 2 for maximum rated current values for various temperatures.
4
Refers to common-mode transients across the insulation barrier.
Common-mode transients exceeding the absolute maximum ratings
can cause latch-up or permanent damage.
1
2
Table 10. Maximum Continuous Working Voltage1
Parameter
AC Voltage,
Bipolar Waveform
Unipolar Waveform
DC Voltage
Max
Unit
Constraint
565
1131
1131
VPEAK
VPEAK
VPEAK
50-year minimum lifetime
50-year minimum lifetime
50-year minimum lifetime
Refers to continuous voltage magnitude imposed across the isolation barrier.
1
Table 11. Truth Table (Positive Logic)
VIA Input 1
H
L
H
L
X
VIB Input1
H
L
L
H
X
VDD1 State
Powered
Powered
Powered
Powered
Unpowered
VDD2 State
Powered
Powered
Powered
Powered
Powered
VOA Output1
H
L
H
L
H
VOB Output1
H
L
L
H
H
X
X
Powered
Unpowered
Indeterminate
Indeterminate
1
H = high, L = low, X = undetermined/not relevant.
Rev. B | Page 10 of 16
Notes
Outputs return to the input state within
1 µs of VDDI power restoration.
Outputs return to the input state within
1 µs of VDDO power restoration.
Data Sheet
ADuM1200-EP
VDD1 1
VIA 2
VIB 3
GND1 4
ADuM1200-EP
TOP VIEW
(Not to Scale)
8
VDD2
7
VOA
6
VOB
5
GND2
09201-003
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 3. Pin Configuration
Table 12. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
Mnemonic
VDD1
VIA
VIB
GND1
GND2
VOB
VOA
VDD2
Description
Supply Voltage for Isolator Side 1.
Logic Input A.
Logic Input B.
Ground 1. Ground reference for Isolator Side 1.
Ground 2. Ground reference for Isolator Side 2.
Logic Output B.
Logic Output A.
Supply Voltage for Isolator Side 2.
Rev. B | Page 11 of 16
ADuM1200-EP
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
20
10
15
CURRENT (mA)
CURRENT/CHANNEL (mA)
8
6
4
5V
3V
10
5V
5
2
3V
30
0
0
4
3
3
CURRENT (mA)
4
2
5V
1
30
2
5V
3V
1
3V
0
0
10
20
DATA RATE (Mbps)
30
Figure 5. Typical Output Supply Current per Channel vs.
Data Rate for 5 V and 3 V Operation (No Output Load)
3
5V
2
0
0
10
20
DATA RATE (Mbps)
30
09201-006
3V
1
0
0
10
20
DATA RATE (Mbps)
Figure 8. Typical VDD2 Supply Current vs.
Data Rate for 5 V and 3 V Operation
4
CURRENT/CHANNEL (mA)
30
Figure 7. Typical VDD1 Supply Current vs.
Data Rate for 5 V and 3 V Operation
09201-005
CURRENT/CHANNEL (mA)
Figure 4. Typical Input Supply Current per Channel vs.
Data Rate for 5 V and 3 V Operation
10
20
DATA RATE (Mbps)
09201-007
10
20
DATA RATE (Mbps)
09201-008
0
09201-004
0
Figure 6. Typical Output Supply Current per Channel vs.
Data Rate for 5 V and 3 V Operation (15 pF Output Load)
Rev. B | Page 12 of 16
Data Sheet
ADuM1200-EP
OUTLINE DIMENSIONS
5.00 (0.1968)
4.80 (0.1890)
1
5
6.20 (0.2441)
5.80 (0.2284)
4
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0040)
COPLANARITY
0.10
SEATING
PLANE
1.75 (0.0688)
1.35 (0.0532)
0.51 (0.0201)
0.31 (0.0122)
0.50 (0.0196)
0.25 (0.0099)
45°
8°
0°
0.25 (0.0098)
0.17 (0.0067)
1.27 (0.0500)
0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-012-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
012407-A
8
4.00 (0.1574)
3.80 (0.1497)
Figure 9. 8-Lead Standard Small Outline Package [SOIC_N]
Narrow Body (R-8)
Dimensions shown in millimeters (inches)
ORDERING GUIDE
Model
ADuM1200UR-EP
ADuM1200UR-EP-RL7
Number
of Inputs,
VDD1 Side
2
2
Number
of Inputs,
VDD2 Side
0
0
Maximum
Data Rate
(Mbps)
25
25
Maximum
Propagation
Delay, 5 V (ns)
45
45
Maximum
Pulse Width
Distortion (ns)
3
3
Rev. B | Page 13 of 16
Temperature
Range
−55°C to +125°C
−55°C to +125°C
Package
Description
8-Lead SOIC_N
8-Lead SOIC_N
Package
Option
R-8
R-8
ADuM1200-EP
Data Sheet
NOTES
Rev. B | Page 14 of 16
Data Sheet
ADuM1200-EP
NOTES
Rev. B | Page 15 of 16
ADuM1200-EP
Data Sheet
NOTES
©2010–2014 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D09201-0-2/14(B)
Rev. B | Page 16 of 16