LT1027 Precision 5V Reference U FEATURES ■ ■ ■ ■ ■ ■ ■ DESCRIPTIO Very Low Drift: 2ppm/°C Max TC Pin Compatible with LT1021-5, REF-02, (PDIP Package) Output Sources 15mA, Sinks 10mA Excellent Transient Response Suitable for A-to-D Reference Inputs Noise Reduction Pin Excellent Long Term Stability Less Than 1ppm P-P Noise (0.1Hz to 10Hz) The LT ®1027 is a precision reference with extra-low drift, superior accuracy, excellent line and load regulation and low output impedance at high frequency. This device is intended for use in 12- to 16-bit A-to-D and D-to-A systems where demanding accuracy requirements must be met without the use of power hungry, heated substrate references. The fast settling output recovers quickly from load transients such as those presented by A-to-D converter reference inputs. The LT1027 brings together both outstanding accuracy and temperature coefficient specifications. A-to-D and D-to-A Converters Digital Voltmeters Reference Standard Precision Current Source The LT1027 reference is based on LTC’s proprietary advanced subsurface Zener bipolar process which eliminates noise and stability problems associated with surface breakdown devices. U APPLICATIO S ■ ■ ■ ■ , LTC and LT are registered trademarks of Linear Technology Corporation. U TYPICAL APPLICATIO Supplying VREF and VCC to the LTC®1290 12-bit ADC Output Voltage ANALOG INPUTS 8V TO 40V VIN + 2.2µF VCC SCLK ACLK DOUT DIN CS LTC1290 REF + VOUT REF – LT1027 + VTRIM 10k 22µF AGND 5.006 TO µC 5.004 OUTPUT VOLTAGE (V) CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 COM 5.002 5.000 4.998 4.996 V– DGND GND 4.994 –50 –25 50 25 0 TEMPERATURE (°C) 75 100 1027 TA01 1027 TA02 sn1027 1027fcs 1 LT1027 W W W AXI U U ABSOLUTE RATI GS (Note 1) Supply Voltage (VIN) ............................................... 40V Input-Output Voltage Differential ............................ 35V Output to Ground Voltage ......................................... 7V VTRIM to Ground Voltage Positive ................................................................ 5V Negative .......................................................... – 0.3V Output Short-Circuit Duration VIN > 20V ........................................................ 10 sec VIN ≤ 20V ................................................... Indefinite Operating Temperature Range LT1027C ................................................ 0°C to 70°C LT1027M (OBSOLETE) ............... – 55°C to 125°C Storage Temperature Range All Devices ....................................... – 65°C to 150°C Lead Temperature (Soldering, 10 sec)................. 300°C W U U PACKAGE/ORDER I FOR ATIO TOP VIEW NC* TOP VIEW TOP VIEW 8 7 NC* NC* 1 VIN 2 NR 3 6 5 4 VOUT VTRIM NC* NR 1 8 VIN VIN 2 7 NC* GND 2 7 NC* NR 3 6 VOUT VTRIM 3 6 NC* GND 4 5 VTRIM VOUT 4 5 NC* NC* 1 GND H PACKAGE 8-LEAD TO-5 METAL CAN 8 N8 PACKAGE 8-LEAD PDIP S8 PACKAGE 8-LEAD PLASTIC SO TJMAX = 100°C, θJA = 130°C/W TJMAX = 100°C, θJA = 180°C/W ORDER PART NUMBER ORDER PART NUMBER ORDER PART NUMBER LT1027ACH-5 LT1027BCH-5 LT1027CCH-5 LT1027DCH-5 LT1027ECH-5 LT1027BCN8-5 LT1027CCN8-5 LT1027DCN8-5 LT1027ECN8-5 LT1027CCS8-5 LT1027DCS8-5 LT1027ECS8-5 TJMAX = 150°C, θJA = 150°C/W, θJC = 45°C/W S8 PART MARKING 1027C5 1027D5 1027E5 OBSOLETE PACKAGE Consider the N8 or S8 Packages for Alternate Source *Connected internally. Do not connect external circuitry to these pins. Consult LTC Marketing for parts specified with wider operating temperature ranges. ELECTRICAL CHARACTERISTICS The ● denotes specifications which apply over the full operating temperature range otherwise specifications are at TA = 25°C. VIN = 10V, ILOAD = 0, unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN VOUT Output Voltage (Note 2) LT1027A LT1027B, C, D LT1027E 4.9990 4.9975 4.9950 TCVOUT Output Voltage Temperature Coefficient (Note 3) LT1027A, B LT1027C LT1027D LT1027E ● ● ● ● TYP MAX 5.000 5.0010 5.000 5.0025 5.000 5.0050 1 2 2 3 2 3 5 7.5 UNITS V ppm/°C sn1027 1027fcs 2 LT1027 ELECTRICAL CHARACTERISTICS The ● denotes specifications which apply over the full operating temperature range otherwise specifications are at TA = 25°C. VIN = 10V, ILOAD = 0, unless otherwise specified. SYMBOL PARAMETER CONDITIONS Line Regulation (Note 4) 8V ≤ VIN ≤ 10V MIN TYP MAX UNITS 6 12 25 ppm/V ppm/V 3 6 8 ppm/V ppm/V –3 6 8 ppm/mA ppm/mA 30 120 ppm/mA 2.2 3.1 3.5 mA mA ● 10V ≤ VIN ≤ 40V ● Load Regulation (Notes 4, 6) Sourcing Current 0 ≤ IOUT ≤ 15mA ● Sinking Current 0 ≥ IOUT ≥ – 10mA –8 –10 ● Supply Current ● VTRIM Adjust Range en ● ±30 ±50 mV 0.1Hz ≤ f ≤ 10Hz 3 10Hz ≤ f ≤ 1kHz 2.0 Temperature Hysteresis H package; ∆T = 25°C 10 ppm Long Term Stability H package 20 ppm/month Output Noise (Note 5) Note 1: Absolute Maximum Ratings are those values beyond which the life of the part may be impaired. Note 2: Output voltage is measured immediately after turn-on. Changes due to chip warm-up are typically less than 0.005%. Note 3: Temperature coefficient is determined by the "box" method in which the maximum ∆VOUT over the temperature range is divided by ∆T. Note 4: Line and load regulation measurements are done on a pulse basis. Output voltage changes due to die temperature change must be taken into account separately. Package thermal resistance is 150°C/W for TO-5 (H), 130°C/W for PDIP (N8), and 180°C/W for plastic SO (SO-8). µVP-P µVRMS 6.0 Note 5: RMS noise is measured with an 8-pole bandpass filter with a center frequency of 30Hz and a Q of 1.5. The filter output is then rectified and integrated for a fixed time period, resulting in an average, as opposed to RMS voltage. A correction factor is used to convert average to RMS. This value is then used to obtain RMS noise voltage in the 10Hz to 1000Hz frequency band. This test also screens for low frequency "popcorn" noise within the bandwidth of the filter. Consult factory for 100% 0.1Hz to 10Hz noise testing. Note 6: Devices typically exhibit a slight negative DC output impedance of – 0.015Ω. This compensates for PC trace resistance, improving regulation at the load. U W TYPICAL PERFOR A CE CHARACTERISTICS Output Impedance vs Frequency Ripple Rejection OUTPUT IMPEDANCE (Ω) 110 REJECTION (dB) ∆I = ±3mA AC ISOURCE = 5mA VIN = 10V 120 100 90 80 70 5.004 10 OUTPUT VOLTAGE (V) 100 Output Voltage 5.006 100 1 0.1 5.002 5.000 4.998 4.996 60 0.01 50 10 100 1k FREQUENCY (Hz) 10k 1027 G01 10 100 1k 10k FREQUENCY (Hz) 100k 1M 1027 G02 4.994 –50 –25 50 25 0 TEMPERATURE (°C) 75 100 1027 G03 sn1027 1027fcs 3 LT1027 U W TYPICAL PERFOR A CE CHARACTERISTICS Start-Up and Turn-Off (No Load) Start-Up and Turn-Off Quiescent Current 2.5 SUPPLY CURRENT (mA) 2.0 VOUT 1V/DIV VOUT 1V/DIV 10V 10V VIN VIN RL = 1k, CL = 4.7µF 1µs/DIV 1027 G04 500µs/DIV 1027 G05 1.5 1.0 0.5 0 0 5 10 15 20 25 30 INPUT VOLTAGE (V) 35 40 1027 G06 Load Regulation 200 400 0 –400 –800 –1200 400 180 OUTPUT NOISE DENSITY (nV/√Hz) CHANGE IN OUTPUT VOLTAGE (µV) CHANGE IN OUTPUT VOLTAGE (µV) Output Noise Voltage Density Line Regulation 500 800 300 200 100 0 –100 –200 –300 8 12 100 80 CNR = 0 60 CNR = 1µF 40 16 20 24 28 32 INPUT VOLTAGE (V) 36 40 10 100 1k FREQUENCY (Hz) 10k 1027 G08 1027 G09 0.1Hz to 10Hz Output Noise Filtering = 1 zero at 0.1Hz 2 poles at 10Hz 5µV/DIV Output Settling Time (Sinking) Output Settling Time (Sourcing) VOUT 400µV/DIV AC COUPLED 10mA LOAD STEP 120 0 –500 1027 G07 VOUT 400µV/DIV AC COUPLED 140 20 –400 –1600 –10 –8 –6 –4 –2 0 2 4 6 8 10 12 14 16 Sink Source IOUT (mA) 160 –10mA LOAD STEP 2µs/DIV 1027 G10 2µs/DIV 1027 G11 1sec/DIV 1027 G12 sn1027 1027fcs 4 LT1027 U W U UO APPLICATI S I FOR ATIO MAXIMUM TEMPERATURE COEFFICIENT FOR 0.5LSB ERROR (ppm/°C) Effect of Reference Drift on System Accuracy A large portion of the temperature drift error budget in many systems is the system reference voltage. Figure 1 indicates the maximum temperature coefficient allowable if the reference is to contribute no more than 0.5LSB error to the overall system performance. The example shown is a 12-bit system designed to operate over a temperature range from 25°C to 65°C. Assuming the system calibration is performed at 25°C, the temperature span is 40°C. It can be seen from the graph that the temperature coefficient of the reference must be no worse than 3ppm/°C if it is to contribute less than 0.5LSB error. For this reason, the LT1027 has been optimized for low drift. 100 8-BIT 10-BIT 10 12-BIT 14-BIT 1.0 0 10 20 30 40 50 60 70 80 90 100 TEMPERATURE SPAN (°C) 1027 AI01 Figure 1. Maximum Allowable Reference Drift Trimming Output Voltage The LT1027 has an adjustment pin for trimming output voltage. The impedance of the VADJ pin is about 20kΩ with an open-circuit voltage of 2.5V. A ±30mV guaranteed trim range is achievable by tying the VADJ pin to the wiper of a 10k potentiometer connecting between the output and ground. Trimming output voltage does not affect the TC of the device. Noise Reduction The positive input of the internal scaling amplifier is brought out as the Noise Reduction (NR) pin. Connecting a 1µF Mylar capacitor between this pin and ground will reduce the wideband noise of the LT1027 from 2.0µVRMS to approximately 1.2µVRMS in a 10Hz to 1kHz bandwidth. Transient response is not affected by this capacitor. Startup settling time will increase to several milliseconds due to the 7kΩ impedance looking into the NR pin. The capacitor must be a low leakage type. Electrolytics are not suitable for this application. Just 100nA leakage current will result in a 150ppm error in output voltage. This pin is the most sensitive pin on the device. For maximum protection a guard ring is recommended. The ring should be driven from a resistive divider from VOUT set to 4.4V (the open-circuit voltage on the NR pin). Transient Response The LT1027 has been optimized for transient response. Settling time is under 2µs when an AC-coupled 10mA load transient is applied to the output. The LT1027 achieves fast settling by using a class B NPN/PNP output stage. When sinking current, the device may oscillate with capacitive loads greater than 100pF. The LT1027 is stable with all capacitive loads when at no DC load or when sourcing current, although for best settling time either no output bypass capactor or a 4.7µF tantalum unit is recommended. An 0.1µF ceramic output capacitor will maximize output ringing and is not recommended. Kelvin Connections Although the LT1027 does not have true force-sense capability, proper hook-up can improve line loss and ground loop problems significantly. Since the ground pin of the LT1027 carries only 2mA, it can be used as a lowside sense line, greatly reducing ground loop problems on the low side of the reference. The VOUT pin should be close to the load or connected via a heavy trace as the resistance of this trace directly affects load regulation. It is important to remember that a 1.22mV drop due to trace resistance is equivalent to a 1LSB error in a 5VFS, 12-bit system. The circuits in Figures 2 and 3 illustrate proper hook-up to minimize errors due to ground loops and line losses. Losses in the output lead can be further reduced by adding a PNP boost transistor if load current is 5mA or higher. R2 can be added to further reduce current in the output sense load. sn1027 1027fcs 5 LT1027 W U U UO APPLICATI S I FOR ATIO INPUT R1 91Ω KEEP THIS LINE RESISTANCE LOW INPUT LT1027 IN 2N4403 OUT + IN LOAD GND LT1027 GROUND RETURN OUT R2* 2.4k GND 1027 F02 + 4.7µF LOAD Figure 2. Standard Hook-Up GROUND RETURN 1027 F03 *OPTIONAL–REDUCES CURRENT IN OUTPUT SENSE LEAD Figure 3. Driving Higher Load Currents U TYPICAL APPLICATIONS 10V Reference 10V Reference VIN VIN IN VIN + OUT 7 10.00V OUTPUT LT1097 LT1027 LT1027 – VTRIM VOUT 1µF OUT 12 5k* GND 11 1µF 5k 8 LTC1043 GND 5k* 13 14 16 17 * 0.1% METAL FILM 1027 TA03 0.01µF 1027 TA04 Operating 5V Reference from 5V Supply 5V LOGIC SUPPLY CMOS LOGIC GATE** 1N914 + fIN ≥ 2kHz* C1 5µF* 1N914 ≈8.5V + C2 5µF* IN LT1027 5V REFERENCE OUT GND 1027 TA05 *FOR HIGHER FREQUENCIES C1 AND C2 MAY BE DECREASED **PARALLEL GATES FOR HIGHER REFERENCE CURRENT LOADING sn1027 1027fcs 6 LT1027 U W EQUIVALE T SCHE ATIC VIN VOUT NR VADJ 1027 ES OUTPUT CURRENT LIMIT AND BIAS CIRCUITS NOT SHOWN GND U PACKAGE DESCRIPTIO H Package 8-Lead TO-5 Metal Can (.230 Inch PCD) (Reference LTC DWG # 05-08-1321) 0.335 – 0.370 (8.509 – 9.398) DIA 0.305 – 0.335 (7.747 – 8.509) 0.040 (1.016) MAX 0.050 (1.270) MAX SEATING PLANE 0.165 – 0.185 (4.191 – 4.699) GAUGE PLANE 0.010 – 0.045* (0.254 – 1.143) REFERENCE PLANE 0.500 – 0.750 (12.700 – 19.050) 0.016 – 0.021** (0.406 – 0.533) 0.027 – 0.045 (0.686 – 1.143) 45°TYP 0.028 – 0.034 (0.711 – 0.864) PIN 1 0.230 (5.842) TYP 0.110 – 0.160 (2.794 – 4.064) INSULATING STANDOFF *LEAD DIAMETER IS UNCONTROLLED BETWEEN THE REFERENCE PLANE AND 0.045" BELOW THE REFERENCE PLANE 0.016 – 0.024 **FOR SOLDER DIP LEAD FINISH, LEAD DIAMETER IS (0.406 – 0.610) H8 (TO-5) 0.230 PCD 1197 OBSOLETE PACKAGE sn1027 1027fcs Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 7 LT1027 U PACKAGE DESCRIPTIO N8 Package 8-Lead PDIP (Narrow .300 Inch) (Reference LTC DWG # 05-08-1510) 0.300 – 0.325 (7.620 – 8.255) 0.009 – 0.015 (0.229 – 0.381) ( 0.130 ± 0.005 (3.302 ± 0.127) 0.045 – 0.065 (1.143 – 1.651) 0.065 (1.651) TYP 8 7 6 5 1 2 3 4 0.255 ± 0.015* (6.477 ± 0.381) +0.035 0.325 –0.015 +0.889 8.255 –0.381 0.400* (10.160) MAX ) 0.125 (3.175) 0.020 MIN (0.508) MIN 0.018 ± 0.003 (0.457 ± 0.076) 0.100 (2.54) BSC N8 1098 *THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm) S8 Package 8-Lead Plastic Small Outline (Narrow .150 Inch) (Reference LTC DWG # 05-08-1610) 0.189 – 0.197* (4.801 – 5.004) 0.010 – 0.020 × 45° (0.254 – 0.508) 0.008 – 0.010 (0.203 – 0.254) 0.053 – 0.069 (1.346 – 1.752) 0°– 8° TYP 0.016 – 0.050 (0.406 – 1.270) 0.014 – 0.019 (0.355 – 0.483) TYP *DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE **DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE 8 7 6 5 0.004 – 0.010 (0.101 – 0.254) 0.050 (1.270) BSC 0.150 – 0.157** (3.810 – 3.988) 0.228 – 0.244 (5.791 – 6.197) 1 2 3 4 SO8 1298 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT1019 Precision Series Bandgap Reference, 0.05%, 5ppm/°C Drift 2.5V, 4.5V, 5V, 10V Outputs; Industrial, Military Grades Available LT1021 Precision Buried Zener Diode Reference, 0.5%, 5ppm/°C Drift 5V, 7V, 10V Outputs; 8-Pin PDIP, SO, TO-5 Packages; Military Grades Available LT1236 Precision Series Reference, 0.05%, 5ppm/°C Drift 5V, 10V Outputs; 8-Pin PDIP, SO Packages; Industrial Grade Available LT1460 Micropower Precision Series Bandgap Reference, 0.075%, 10ppm/°C Drift 2.5V, 5V, 10V Outputs; 8-Pin PDIP, SO, MSOP; TO-92 and SOT-23 Packages LT1461 Low Dropout 3ppm/°C Drift, 0.04% Series Reference 2.5V, SO-8 Package LT1798 Low Dropout, Micropower Reference 2.5V, 3V, 4.096V, 5V, Adjustable in SO-8 sn1027 1027fcs 8 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com LT/CPI 1101 1.5K REV C • PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 1992