Data Sheet Complete Quad, 16-Bit, High Accuracy, Serial Input, ±5 V DAC AD5765 FEATURES GENERAL DESCRIPTION Complete quad, 16-bit digital-to-analog converter (DAC) Programmable output range: ±4.096 V, ±4.201 V, or ±4.311 V ±1 LSB maximum INL error, ±1 LSB maximum DNL error Low noise: 70 nV/√Hz Settling time: 10 μs maximum Integrated reference buffers On-chip die temperature sensor Output control during power-up/brownout Programmable short-circuit protection Simultaneous updating via LDAC Asynchronous CLR to zero code Digital offset and gain adjustment Logic output control pins DSP-/microcontroller-compatible serial interface Temperature range: −40°C to +105°C iCMOS® process technology1 The AD5765 is a quad, 16-bit, serial input, bipolar voltage output, digital-to-analog converter (DAC) that operates from supply voltages of ±4.75 V to ±5.25 V. The nominal full-scale output range is ±4.096 V. The AD5765 provides integrated output amplifiers, reference buffers, and proprietary powerup/power-down control circuitry. The part also features a digital I/O port, which is programmed via the serial interface. The part incorporates digital offset and gain adjustment registers per channel. APPLICATIONS Industrial automation Open-/closed-loop servo control Process control Data acquisition systems Automatic test equipment Automotive test and measurement High accuracy instrumentation The AD5765 is a high performance converter that offers guaranteed monotonicity, integral nonlinearity (INL) of ±1 LSB, low noise, and 10 μs settling time. During power-up (when the supply voltages are changing), the outputs are clamped to 0 V via a low impedance path. The AD5765 uses a serial interface that operates at clock rates of up to 30 MHz and is compatible with DSP and microcontroller interface standards. Double buffering allows the simultaneous updating of all DACs. The input coding is programmable to either a twos complement or an offset binary format. The asynchronous clear function clears all DAC registers to either bipolar zero or zero scale, depending on the coding used. The AD5765 is ideal for both closed-loop servo control and openloop control applications. The AD5765 is available in a 32-lead TQFP and offers guaranteed specifications over the −40°C to +105°C industrial temperature range. Figure 1 contains a functional block diagram of the AD5765. Table 1. Related Devices Part No. AD5764 AD5763 1 Description Complete quad, 16-bit, high accuracy, serial input, ±10 V DAC Complete dual, 16-bit, high accuracy, serial input, ±5 V DAC For analog systems designers within industrial/instrumentation equipment OEMs who need high performance ICs at higher voltage levels, iCMOS is a technology platform that enables the development of analog ICs capable of 30 V and operating at ±15 V supplies, allowing dramatic reductions in power consumption and package size and increased ac and dc performance. Rev. C Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2009–2011 Analog Devices, Inc. All rights reserved. AD5765 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Data Register ............................................................................... 20 Applications ....................................................................................... 1 Coarse Gain Register ................................................................. 20 General Description ......................................................................... 1 Fine Gain Register ...................................................................... 21 Revision History ............................................................................... 2 Offset Register ............................................................................ 21 Functional Block Diagram .............................................................. 3 Offset and Gain Adjustment Worked Example...................... 22 Specifications..................................................................................... 4 Design Features ............................................................................... 23 AC Performance Characteristics ................................................ 6 Analog Output Control ............................................................. 23 Timing Characteristics ................................................................ 7 Digital Offset and Gain Control ............................................... 23 Absolute Maximum Ratings.......................................................... 10 Programmable Short-Circuit Protection ................................ 23 Thermal Resistance .................................................................... 10 Digital I/O Port ........................................................................... 23 ESD Caution ................................................................................ 10 Die Temperature Sensor ............................................................ 23 Pin Configuration and Function Descriptions ........................... 11 Local-Ground-Offset Adjustment ........................................... 23 Typical Performance Characteristics ........................................... 13 Power-On Status ......................................................................... 24 Terminology .................................................................................... 16 Applications Information .............................................................. 25 Theory of Operation ...................................................................... 17 Typical Operating Circuit ......................................................... 25 DAC Architecture ....................................................................... 17 Precision Voltage Reference Selection ..................................... 25 Reference Buffers ........................................................................ 17 Layout Guidelines ........................................................................... 26 Serial Interface ............................................................................ 17 Galvanically Isolated Interface ................................................. 26 Simultaneous Updating via LDAC ........................................... 18 Microprocessor Interfacing ....................................................... 26 Transfer Function ....................................................................... 19 Outline Dimensions ....................................................................... 27 Asynchronous Clear (CLR) ....................................................... 19 Ordering Guide .......................................................................... 27 Function Register ....................................................................... 20 REVISION HISTORY 10/11—Rev. B to Rev. C Changed 50 MHz to 30 MHz ....................................... Throughout Changes to t1, t2, and t3 Parameters, Table 4 .................................. 7 7/11—Rev. A to Rev. B Changed 30 MHz to 50 MHz Throughout.................................... 1 Changes to t1, t2, and t3 Parameters, Table 4 .................................. 7 Changes to Table 21 ........................................................................ 25 Changes to Ordering Guide .......................................................... 27 10/09—Rev. 0 to Rev. A Deleted Endnote 1, Table 2 .............................................................. 4 Deleted Endnote 1, Table 3 .............................................................. 6 Deleted Endnote 1, Table 4 .............................................................. 7 Changes to t6 Parameter, Table 4 .................................................... 7 1/09—Revision 0: Initial Version Rev. C | Page 2 of 28 Data Sheet AD5765 FUNCTIONAL BLOCK DIAGRAM PGND AVDD AVSS AVDD AVSS REFGND DVCC DGND REFERENCE BUFFERS AD5765 16 SDIN SCLK SYNC SDO INPUT SHIFT REGISTER AND CONTROL LOGIC INPUT REG A DAC REG A RSTOUT REFAB RSTIN VOLTAGE MONITOR AND CONTROL ISCC G1 16 DAC A VOUTA G2 GAIN REG A AGNDA OFFSET REG A INPUT REG B DAC REG B G1 16 DAC B VOUTB G2 GAIN REG B AGNDB OFFSET REG B D0 D1 INPUT REG C DAC REG C G1 16 DAC C VOUTC G2 GAIN REG C AGNDC OFFSET REG C BIN/2sCOMP INPUT REG D DAC REG D G1 16 DAC D VOUTD G2 GAIN REG D AGNDD OFFSET REG D LDAC Figure 1. Rev. C | Page 3 of 28 REFERENCE BUFFERS TEMP SENSOR REFCD TEMP 07249-001 CLR AD5765 Data Sheet SPECIFICATIONS AVDD = 4.75 V to 5.25 V, AVSS = −4.75 V to −5.25 V, AGNDx = DGND = REFGND = PGND = 0 V, REFAB = REFCD = 2.048 V, DVCC = 2.7 V to 5.25 V, RLOAD = 5 kΩ, CLOAD = 200 pF. All specifications TMIN to TMAX, unless otherwise noted. Table 2. Parameter ACCURACY Resolution Relative Accuracy (INL) Differential Nonlinearity (DNL) Bipolar Zero Error Bipolar Zero Temperature Coefficient (TC) 2 Zero-Scale Error Zero-Scale Temperature Coefficient (TC)2 Gain Error Gain TC2 DC Crosstalk2 REFERENCE INPUT2 Reference Input Voltage DC Input Impedance Input Current Reference Range OUTPUT CHARACTERISTICS2 Output Voltage Range 3 Output Voltage Drift vs. Time Short-Circuit Current Load Current Capacitive Load Stability RLOAD = ∞ RLOAD = 10 kΩ DC Output Impedance DIGITAL INPUTS2 VIH, Input High Voltage VIL, Input Low Voltage Input Current Pin Capacitance B Grade 1 C Grade1 Unit Test Conditions/Comments Outputs unloaded 16 ±2 ±1 ±2 ±3 ±1 16 ±1 ±1 ±2 ±3 ±1 Bits LSB max LSB max mV max mV max ppm FSR/°C typ ±2 ±3.5 ±1 ±2 ±3.5 ±1 mV max mV max ppm FSR/°C typ At 25°C ±0.03 ±0.04 ±1 0.5 ±0.03 ±0.04 ±1 0.5 % FSR max % FSR max ppm FSR/°C typ LSB max At 25°C, coarse gain register = 0 Coarse gain register = 0 2.048 1 ±10 1 to 2.1 2.048 1 ±10 1 to 2.1 V nominal MΩ min µA max V min to V max ±1% for specified performance Typically, 100 MΩ Typically, ±30 nA ±4.31158 ±4.20103 ±4.096 ±4.42105 ±32 ±37 10 ±1 ±4.31158 ±4.20103 ±4.096 ±4.42105 ±32 ±37 10 ±1 V min/V max V min/V max V min/V max V min/V max ppm FSR/500 hours typ ppm FSR/1000 hours typ mA typ mA max Coarse gain register = 2 Coarse gain register = 1 Coarse gain register = 0 VREFIN = 2.1 V, coarse gain register = 2 200 1000 0.3 200 1000 0.3 pF max pF max Ω max Guaranteed monotonic At 25°C RISCC = 6 kΩ; see Figure 23 For specified performance DVCC = 2.7 V to 5.25 V, JEDEC compliant 2 0.8 ±1 10 2 0.8 ±1 10 V min V max µA max pF max Rev. C | Page 4 of 28 Per pin Per pin Data Sheet Parameter DIGITAL OUTPUTS (D0, D1, SDO)2 Output Low Voltage Output High Voltage Output Low Voltage Output High Voltage High Impedance Leakage Current High Impedance Output Capacitance DIE TEMPERATURE SENSOR Output Voltage at 25°C Output Voltage Scale Factor Output Voltage Range Output Load Current Power-On Time POWER REQUIREMENTS AVDD/AVSS DVCC AIDD AISS DICC Power Supply Sensitivity2 ∆VOUT/∆ΑVDD Power Dissipation AD5765 B Grade 1 C Grade1 Unit Test Conditions/Comments 0.4 DVCC − 1 0.4 DVCC − 0.5 ±1 5 0.4 DVCC − 1 0.4 DVCC − 0.5 ±1 5 V max V min V max V min µA max pF typ DVCC = 5 V ± 5%, sinking 200 µA DVCC = 5 V ± 5%, sourcing 200 µA DVCC = 2.7 V to 3.6 V, sinking 200 µA DVCC = 2.7 V to 3.6 V, sourcing 200 µA SDO only SDO only 1.44 3 1.175 to 1.9 200 10 1.44 3 1.175 to 1.9 200 10 V typ mV/°C typ V min to V max µA max ms typ 4.75 to 5.25 2.7 to 5.25 2.25 1.9 1.2 4.75 to 5.25 2.7 to 5.25 2.25 1.9 1.2 V min to V max V min to V max mA/channel max mA/channel max mA max Outputs unloaded Outputs unloaded VIH = DVCC, VIL = DGND, 750 µA typ −110 76 −110 76 dB typ mW typ ±5 V operation output unloaded Temperature range: −40°C to +105°C; typical at +25°C. Guaranteed by design and characterization; not production tested. 3 Output amplifier headroom requirement is 0.5 V minimum. 1 2 Rev. C | Page 5 of 28 AD5765 Data Sheet AC PERFORMANCE CHARACTERISTICS AVDD = 4.75 V to 5.25 V, AVSS = −4.75 V to −5.25 V, AGNDx = DGND = REFGND = PGND = 0 V, REFAB = REFCD = 2.048 V, DVCC = 2.7 V to 5.25 V, RLOAD = 5 kΩ, CLOAD = 200 pF. All specifications TMIN to TMAX, unless otherwise noted. Table 3. Parameter DYNAMIC PERFORMANCE 1 Output Voltage Settling Time Slew Rate Digital-to-Analog Glitch Energy Glitch Impulse Peak Amplitude Channel-to-Channel Isolation DAC-to-DAC Crosstalk Digital Crosstalk Digital Feedthrough Output Noise, 0.1 Hz to 10 Hz Output Noise, 0.1 Hz to 100 kHz 1/f Corner Frequency Output Noise Spectral Density Complete System Output Noise Spectral Density 2 1 2 B Grade C Grade Unit Test Conditions/Comments 8 10 2 5 20 30 60 8 2 2 0.1 50 300 70 80 8 10 2 5 20 30 60 8 2 2 0.1 50 300 70 80 µs typ µs max µs typ V/µs typ nV-sec typ mV typ dB typ nV-sec typ nV-sec typ nV-sec typ LSB p-p typ µV rms typ Hz typ nV/√Hz typ nV/√Hz typ Full-scale step to ±1 LSB Guaranteed by design and characterization; not production tested. Includes noise contributions from integrated reference buffers, 16-bit DAC, and output amplifier. Rev. C | Page 6 of 28 512 LSB step settling Effect of input bus activity on DAC outputs Measured at 10 kHz Measured at 10 kHz Data Sheet AD5765 TIMING CHARACTERISTICS AVDD = 4.75 V to 5.25 V, AVSS = −4.75 V to −5.25 V, AGNDx = DGND = REFGND = PGND = 0 V, REFAB = REFCD = 2.048 V, DVCC = 2.7 V to 5.25 V, RLOAD = 5 kΩ, CLOAD = 200 pF. All specifications TMIN to TMAX, unless otherwise noted. Table 4. Parameter 1, 2, 3 t1 t2 t3 t4 t5 4 t6 t7 t8 t9 t10 t11 t12 t13 t14 t15 5, 6 t16 t17 t18 Limit at TMIN, TMAX 33 13 13 13 13 90 2 5 1.7 480 10 500 10 10 2 25 13 2 170 Unit ns min ns min ns min ns min ns min ns min ns min ns min µs min ns min ns min ns max µs max ns min µs max ns max ns min µs max ns min Description SCLK cycle time SCLK high time SCLK low time SYNC falling edge to SCLK falling edge setup time 24th SCLK falling edge to SYNC rising edge Minimum SYNC high time Data setup time Data hold time SYNC rising edge to LDAC falling edge when all DACs are updated SYNC rising edge to LDAC falling edge when a single DAC is updated LDAC pulse width low LDAC falling edge to DAC output response time DAC output settling time CLR pulse width low CLR pulse activation time SCLK rising edge to SDO valid SYNC rising edge to SCLK falling edge SYNC rising edge to DAC output response time (LDAC = 0) LDAC falling edge to SYNC rising edge Guaranteed by design and characterization; not production tested. All input signals are specified with tR = tF = 5 ns (10% to 90% of DVCC) and timed from a voltage level of 1.2 V. See Figure 2, Figure 3, and Figure 4. 4 Standalone mode only. 5 Measured with the load circuit of Figure 5. 6 Daisy-chain mode only. 1 2 3 Rev. C | Page 7 of 28 AD5765 Data Sheet t1 SCLK 1 2 24 t3 t6 t2 t4 t5 SYNC t8 t7 SDIN DB23 DB0 t10 t9 LDAC t10 t18 t12 t11 VOUTx LDAC = 0 t12 t17 VOUTx t13 CLR t14 07249-002 VOUTx Figure 2. Serial Interface Timing Diagram t1 SCLK 24 t3 t6 48 t2 t5 t16 t4 SYNC t7 SDIN t8 DB23 DB0 INPUT WORD FOR DAC N DB23 DB0 t15 INPUT WORD FOR DAC N – 1 DB23 SDO UNDEFINED DB0 INPUT WORD FOR DAC N t9 t10 07249-003 LDAC Figure 3. Daisy-Chain Timing Diagram Rev. C | Page 8 of 28 Data Sheet AD5765 SCLK 24 48 SYNC DB0 DB23 DB0 NOP CONDITION INPUT WORD SPECIFIES REGISTER TO BE READ DB23 SDO UNDEFINED DB0 SELECTED REGISTER DATA CLOCKED OUT Figure 4. Readback Timing Diagram 200µA TO OUTPUT PIN IOL VOH (MIN) OR VOL (MAX) CL 50pF 200µA IOH Figure 5. Load Circuit for SDO Timing Diagram Rev. C | Page 9 of 28 07249-004 DB23 07249-005 SDIN AD5765 Data Sheet ABSOLUTE MAXIMUM RATINGS TA = 25°C, unless otherwise noted. Transient currents of up to 100 mA do not cause SCR latch-up. Table 5. Parameter AVDD to AGNDx, DGND AVSS to AGNDx, DGND DVCC to DGND DVCC to AVDD Digital Inputs to DGND Digital Outputs to DGND REFx to AGNDx, PGND VOUTx to AGNDx AGNDx to DGND Operating Temperature Range (TA) Industrial Storage Temperature Range Junction Temperature (TJ max) Power Dissipation Lead Temperature Soldering Rating −0.3 V to +7 V +0.3 V to −7 V −0.3 V to +7 V −DVCC to +0.25 V −0.3 V to DVCC + 0.3 V or 7 V (whichever is less) −0.3 V to DVCC + 0.3 V −0.3 V to AVDD + 0.3 V AVSS to AVDD −0.3 V to +0.3 V −40°C to +105°C −65°C to +150°C 150°C (TJ max – TA)/θJA JEDEC industry standard J-STD-020 Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. THERMAL RESISTANCE θJA is specified for the worst-case conditions, that is, a device soldered in a circuit board for surface-mount packages. Table 6. Thermal Resistance Package Type 32-Lead TQFP ESD CAUTION Rev. C | Page 10 of 28 θJA 65 θJC 12 Unit °C/W Data Sheet AD5765 REFAB REFCD NC REFGND TEMP AVSS AVDD BIN/2sCOMP PIN CONFIGURATION AND FUNCTION DESCRIPTIONS 24 AGNDA 23 VOUTA 22 VOUTB 21 AGNDB 20 AGNDC LDAC 6 19 VOUTC D0 7 18 VOUTD D1 8 17 AGNDD PIN 1 SCLK 2 SDIN 3 AD5765 SDO 4 TOP VIEW (Not to Scale) ISCC AVSS PGND AVDD DVCC 10 11 12 13 14 15 16 DGND 9 RSTIN NC = NO CONNECT RSTOUT CLR 5 07249-006 32 31 30 29 28 27 26 25 SYNC 1 Figure 6. Pin Configuration Table 7. Pin Function Descriptions Pin No. 1 Mnemonic SYNC 2 SCLK 3 4 51 6 SDIN SDO CLR LDAC 7, 8 D0, D1 9 RSTOUT 10 RSTIN 11 12 13, 31 14 15, 30 16 DGND DVCC AVDD PGND AVSS ISCC 17 18 AGNDD VOUTD Description Active Low Input. This is the frame synchronization signal for the serial interface. While SYNC is low, data is transferred in on the falling edge of SCLK. Serial Clock Input. Data is clocked into the shift register on the falling edge of SCLK. This operates at clock speeds of up to 30 MHz. Serial Data Input. Data must be valid on the falling edge of SCLK. Serial Data Output. This is used to clock data from the serial register in daisy-chain or readback mode. Negative Edge Triggered Input. Asserting this pin sets the DAC registers to 0x0000. Load DAC. Logic input. This is used to update the DAC registers and consequently the analog outputs. When tied permanently low, the addressed DAC register is updated on the rising edge of SYNC. If LDAC is held high during the write cycle, the DAC input register is updated but the output update is held off until the falling edge of LDAC. In this mode, all analog outputs can be updated simultaneously on the falling edge of LDAC. The LDAC pin must not be left unconnected. D0 and D1 form a digital I/O port. The user can set up these pins as inputs or outputs that are configurable and readable over the serial interface. When configured as inputs, these pins have weak internal pull-ups to DVCC. When programmed as outputs, D0 and D1 are referenced by DVCC and DGND. Reset Logic Output. This is the output from the on-chip voltage monitor used in the reset circuit. If desired, it can be used to control other system components. Reset Logic Input. This input allows external access to the internal reset logic. Applying a Logic 0 to this input clamps the DAC outputs to 0 V. In normal operation, RSTIN should be tied to Logic 1. Register values remain unchanged. Digital Ground Pin. Digital Supply Pin. Voltage ranges from 2.7 V to 5.25 V. Positive Analog Supply Pins. Voltage ranges from 4.75 V to 5.25 V. Ground Reference Point for Analog Circuitry. Negative Analog Supply Pins. Voltage ranges from –4.75 V to –5.25 V. This pin is used in association with an optional external resistor to AGND to program the short-circuit current of the output amplifiers. See the Design Features section for additional details. Ground Reference Pin for the DAC D Output Amplifier. Analog Output Voltage of DAC D. This provides buffered output with a nominal full-scale output range of ±4.096 V. The output amplifier is capable of directly driving a 5 kΩ, 200 pF load. Rev. C | Page 11 of 28 AD5765 Pin No. 19 Mnemonic VOUTC 20 21 22 AGNDC AGNDB VOUTB 23 VOUTA 24 25 AGNDA REFAB 26 REFCD 27 28 29 NC REFGND TEMP 32 BIN/2sCOMP 1 Data Sheet Description Analog Output Voltage of DAC C. This provides buffered output with a nominal full-scale output range of ±4.096 V. The output amplifier is capable of directly driving a 5 kΩ, 200 pF load. Ground Reference Pin for the DAC C Output Amplifier. Ground Reference Pin for the DAC B Output Amplifier. Analog Output Voltage of DAC B. This provides buffered output with a nominal full-scale output range of ±4.096 V. The output amplifier is capable of directly driving a 5 kΩ, 200 pF load. Analog Output Voltage of DAC A. This provides buffered output with a nominal full-scale output range of ±4.096 V. The output amplifier is capable of directly driving a 5 kΩ, 200 pF load. Ground Reference Pin for the DAC A Output Amplifier. External Reference Voltage Input for Channel A and Channel B. The reference input range is 1 V to 2.1 V; this programs the full-scale output voltage. VREFIN = 2.048 V for specified performance. External Reference Voltage Input for Channel C and Channel D. The reference input range is 1 V to 2.1 V; this programs the full-scale output voltage. VREFIN = 2.048 V for specified performance. No Connect. Reference Ground Return for the Reference Generator and Buffers. This pin provides an output voltage proportional to temperature. The output voltage is 1.4 V, typical, at 25°C die temperature; variation with temperature is 5 mV/°C. Determines the DAC Coding. This pin should be hardwired to either DVCC or DGND. When hardwired to DVCC, input coding is offset binary. When hardwired to DGND, input coding is twos complement (see Table 8). Internal pull-up device on this logic input. Therefore, it can be left floating and defaults to a logic high condition. Rev. C | Page 12 of 28 Data Sheet AD5765 TYPICAL PERFORMANCE CHARACTERISTICS 0.30 1.0 0.25 TA = 25°C 0.8 0.20 0.15 0.4 DNL ERROR (LSBs) 0.2 0 –0.2 –0.4 0.10 0.05 0 0.05 0.10 –0.6 07249-007 –0.15 –0.8 –1.0 0 10,000 20,000 30,000 40,000 CODE 50,000 07249-010 INL ERROR (LSBs) 0.6 –0.20 –0.25 –40 60,000 Figure 7. Integral Nonlinearity Error vs. Code –20 0 20 40 60 TEMPERATURE (°C) 80 100 Figure 10. Differential Nonlinearity Error vs. Temperature 8.7 1.0 AIDD 8.6 TA = 25°C 0.8 0.6 8.5 0.4 8.4 AIDD /AISS (mA) 0 –0.2 8.3 8.2 8.1 –0.4 8.0 –0.6 7.9 –0.8 AISS –1.0 0 10,000 20,000 30,000 40,000 CODE 50,000 7.8 7.7 4.5 60,000 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 AVDD/AVSS (V) Figure 11. AIDD/AISS vs. AVDD/AVSS Figure 8. Differential Nonlinearity Error vs. Code 0.80 0.3 0.75 ZERO-SCALE ERROR (mV) 0.4 0.2 0.1 0 –0.1 0.70 0.65 0.60 –0.3 –40 –20 0 20 40 60 TEMPERATURE (°C) 80 0.50 –40 100 Figure 9. Integral Nonlinearity Error vs. Temperature 07249-017 0.55 –0.2 07249-009 INL ERROR (LSBs) 07249-016 0.2 07249-008 DNL ERROR (LSBs) TA = 25°C –20 0 20 40 60 TEMPERATURE (°C) 80 Figure 12. Zero-Scale Error vs. Temperature Rev. C | Page 13 of 28 100 Data Sheet 0.20 2.0 0.18 1.5 OUTPUT VOLTAGE DELTA (mV) 0.16 0.14 0.12 0.10 –20 0 20 40 60 TEMPERATURE (°C) 80 0 –0.5 –1.0 –2.0 –8 100 –0.009 3 OUTPUT VOLTAGE DELTA (mV) 4 –0.010 –0.011 –0.012 –0.013 –0.014 0 20 40 60 TEMPERATURE (°C) –2 0 2 4 6 8 10 80 AVDD = +5V AVSS = –5V TA = 25°C 2 1 0 –1 –2 –3 07249-019 –0.015 –20 –4 Figure 16. Source and Sink Capability of Output Amplifier with Positive Full-Scale Loaded –0.008 –0.016 –40 –6 SOURCE/SINK CURRENT (mA) Figure 13. Bipolar Zero Error vs. Temperature GAIN ERROR (%FSR) 0.5 07249-021 0.06 –40 1.0 –1.5 07249-018 0.08 AVDD = +5V AVSS = –5V TA = 25°C –4 –10 100 07249-022 BIPOLAR ZERO ERROR (mV) AD5765 –8 –6 –4 –2 0 2 4 6 8 10 SOURCE/SINK CURRENT (mA) Figure 14. Gain Error vs. Temperature Figure 17. Source and Sink Capability of Output Amplifier with Negative FullScale Loaded 4.0 TA = 25°C 3.5 3.0 1 2.0 1.5 0.5 07249-023 1.0 07249-020 DICC (mA) 2.5 0 0 1 2 3 4 LOGIC INPUT VOLTAGE (V) CH1 1.25V 5 Figure 15. DICC vs. Logic Input Voltage M1.00µs CH1 Figure 18. Positive Full-Scale Step Rev. C | Page 14 of 28 –175mV Data Sheet AD5765 1 2 1 CH1 1.25V M1.00µs CH1 07249-024 07249-024 3 175mV CH1 5.00V CH3 50.0mV M25.0ms CH1 4.1V Figure 22. VOUT vs. AVDD/AVSS on Power-Up Figure 19. Negative Full-Scale Step 40 10 0x7FFF TO 0x8000 0x8000 TO 0x7FFF 20 10 0 –10 –20 07249-026 –30 –40 –1.0 –0.5 0 0.5 1.0 TIME (µs) 1.5 2.0 2.5 TA = 25°C 9 SHORT-CIRCUIT CURRENT (mA) 30 8 7 6 5 4 3 2 07249-029 TA = 25°C 1 0 3.0 1 Figure 20. Major Code Transition Glitch Energy 2 3 4 5 6 RISCC (kΩ) 7 8 9 10 Figure 23. Short-Circuit Current vs. RISCC 1.8 TEMP OUTPUT VOLTAGE (V) AVDD = +5V AVSS = –5V 4 CH4 50µV M1.00µs CH4 1.7 1.6 1.5 1.4 1.2 –40 26µV Figure 21. Peak-to-Peak Noise (100 kHz Bandwidth) 07249-030 1.3 07249-027 OUTPUT VOLTAGE (mV) CH2 5.00V –20 0 20 40 60 TEMPERATURE (°C) 80 Figure 24. TEMP Output Voltage vs. Temperature Rev. C | Page 15 of 28 100 AD5765 Data Sheet TERMINOLOGY Relative Accuracy or Integral Nonlinearity (INL) For the DAC, relative accuracy or integral nonlinearity (INL) is a measure of the maximum deviation, in LSBs, from a straight line passing through the endpoints of the DAC transfer function. A typical INL vs. code plot can be seen in Figure 7. Differential Nonlinearity (DNL) Differential nonlinearity is the difference between the measured change and the ideal 1 LSB change between any two adjacent codes. A specified differential nonlinearity of ±1 LSB maximum ensures monotonicity. This DAC is guaranteed monotonic. A typical DNL vs. code plot can be seen in Figure 8. Monotonicity A DAC is monotonic if the output either increases or remains constant for increasing digital input code. The AD5765 is monotonic over its full operating temperature range. Bipolar Zero Error Bipolar zero error is the deviation of the analog output from the ideal half-scale output of 0 V when the DAC register is loaded with 0x8000 (offset binary coding) or 0x0000 (twos complement coding). A plot of bipolar zero error vs. temperature can be seen in Figure 13. Bipolar Zero Temperature Coefficient (TC) Bipolar zero temperature coefficient is the measure of the change in the bipolar zero error with a change in temperature. It is expressed as (ppm FSR)/°C. Full-Scale Error Full-scale error is a measure of the output error when full-scale code is loaded to the DAC register. Ideally, the output voltage should be 2 × VREF − 1 LSB. Full-scale error is expressed as a percentage of the full-scale range. Negative Full-Scale Error/Zero Scale Error Negative full-scale error is the error in the DAC output voltage when 0x0000 (offset binary coding) or 0x8000 (twos complement coding) is loaded to the DAC register. Ideally, the output voltage is −2 × VREF. A plot of zero-scale error vs. temperature can be seen in Figure 12. Output Voltage Settling Time Output voltage settling time is the amount of time it takes for the output to settle to a specified level for a full-scale input change. Slew Rate The slew rate of a device is a limitation in the rate of change of the output voltage. The output slewing speed of a voltageoutput DAC is usually limited by the slew rate of the amplifier used at its output. Slew rate is measured from 10% to 90% of the output signal and is given in V/µs. Gain Error Gain error is a measure of the span error of the DAC. It is the deviation in slope of the DAC transfer characteristic from the ideal, expressed as a percentage of the full-scale range. A plot of gain error vs. temperature can be seen in Figure 14. Total Unadjusted Error (TUE) Total unadjusted error (TUE) is a measure of the output error considering all the various errors. Zero-Scale Error Temperature Coefficient Zero-scale error temperature coefficient is a measure of the change in zero-scale error with a change in temperature. Zeroscale error TC is expressed as (ppm FSR)/°C. Gain Error Temperature Coefficient Gain error temperature coefficient is a measure of the change in gain error with changes in temperature. Gain error temperature coefficient is expressed as (ppm of FSR)/°C. Digital-to-Analog Glitch Impulse Digital-to-analog glitch impulse is the impulse injected into the analog output when the input code in the DAC register changes state. It is normally specified as the area of the glitch in nV-sec and is measured when the digital input code is changed by 1 LSB at the major carry transition, 0x7FFF to 0x8000 (see Figure 20). Digital Feedthrough Digital feedthrough is a measure of the impulse injected into the analog output of the DAC from the digital inputs of the DAC but is measured when the DAC output is not updated. It is specified in nV-sec and is measured with a full-scale code change on the data bus, that is, from all 0s to all 1s and vice versa. Power Supply Sensitivity Power supply sensitivity indicates how the output of the DAC is affected by changes in the power supply voltage. DC Crosstalk DC crosstalk is the dc change in the output level of one DAC in response to a change in the output of another DAC. It is measured with a full-scale output change on one DAC while monitoring another DAC and is expressed in LSBs. DAC-to-DAC Crosstalk DAC-to-DAC crosstalk is the glitch impulse transferred to the output of one DAC due to a digital code change and subsequent output change of another DAC. This includes both digital and analog crosstalk. It is measured by loading one of the DACs with a full-scale code change (all 0s to all 1s and vice versa) with LDAC low and monitoring the output of another DAC. The energy of the glitch is expressed in nV-sec. Channel-to-Channel Isolation Channel-to-channel isolation is the ratio of the amplitude of the signal at the output of one DAC to a sine wave on the reference input of another DAC. It is measured in decibels. Digital Crosstalk Digital crosstalk is a measure of the impulse injected into the analog output of one DAC from the digital inputs of another DAC but is measured when the DAC output is not updated. It is specified in nV-sec and measured with a full-scale code change on the data bus, that is, from all 0s to all 1s and vice versa. Rev. C | Page 16 of 28 Data Sheet AD5765 THEORY OF OPERATION The AD5765 is a quad, 16-bit, serial input, bipolar voltage output DAC that operates from supply voltages of ±4.75 V to ±5.25 V and has a buffered output voltage of up to ±4.311 V. Data is written to the AD5765 in a 24-bit word format, via a 3-wire serial interface. The device also offers an SDO pin, which is available for daisychaining or readback. The AD5765 incorporates a power-on reset circuit, which ensures that the DAC registers power up loaded with 0x0000. The AD5765 features a digital I/O port that can be programmed via the serial interface, on-chip reference buffers and per channel digital gain, and offset registers. DAC ARCHITECTURE The DAC architecture of the AD5765 consists of a 16-bit current mode segmented R-2R DAC. The simplified circuit diagram for the DAC section is shown in Figure 25. The four MSBs of the 16-bit data-word are decoded to drive 15 switches, E1 to E15. Each of these switches connects one of the 15 matched resistors to either AGNDx or IOUT. The remaining 12 bits of the data-word drive switches S0 to S11 of the 12-bit R-2R ladder network. R VREF 2R 2R E15 E14 R 2R 2R R 2R 2R 2R S11 S10 S0 IOUT VOUTx 07249-060 AGNDx 4 MSBs DECODED INTO 15 EQUAL SEGMENTS The AD5765 is controlled over a versatile 3-wire serial interface that operates at clock rates of up to 30 MHz and is compatible with SPI, QSPI™, MICROWIRE™, and DSP standards. Input Shift Register The input shift register is 24 bits wide. Data is loaded into the device MSB first as a 24-bit word under the control of a serial clock input, SCLK. The input register consists of a read/write bit, three register select bits, three DAC address bits, and 16 data bits as shown in Table 9. The timing diagram for this operation is shown in Figure 2. At power-up, the DAC registers are loaded with zero code (0x0000), and the outputs are clamped to 0 V via a low impedance path. The outputs can be updated with the zero code value at this time by asserting either LDAC or CLR. The corresponding output voltage depends on the state of the BIN/2sCOMP pin. If the BIN/2sCOMP pin is tied to DGND, the data coding is twos complement, and the outputs update to 0 V. If the BIN/2sCOMP pin is tied to DVCC, the data coding is offset binary, and the outputs update to negative full scale. To have the outputs power up with zero code loaded to the outputs, the CLR pin should be held low during power-up. Standalone Operation R/8 E1 SERIAL INTERFACE 12-BIT, R-2R LADDER Figure 25. DAC Ladder Structure REFERENCE BUFFERS The AD5765 operates with an external reference. The reference inputs (REFAB and REFCD) have an input range up to 2.1 V. This input voltage is then used to provide a buffered positive and negative reference for the DAC cores. The positive reference is given by +VREF = 2 VREF The negative reference to the DAC cores is given by −VREF = −2 VREF These positive and negative reference voltages (along with the gain register values) define the output ranges of the DACs. The serial interface works with both a continuous and noncontinuous serial clock. A continuous SCLK source can be used only if SYNC is held low for the correct number of clock cycles. In gated clock mode, a burst clock containing the exact number of clock cycles must be used, and SYNC must be taken high after the final clock to latch the data. The first falling edge of SYNC starts the write cycle. Exactly 24 falling clock edges must be applied to SCLK before SYNC is brought high again. If SYNC is brought high before the 24th falling SCLK edge, the data written is invalid. If more than 24 falling SCLK edges are applied before SYNC is brought high, the input data is also invalid. The input register addressed is updated on the rising edge of SYNC. In order for another serial transfer to take place, SYNC must be brought low again. After the end of the serial data transfer, data is automatically transferred from the input shift register to the addressed register. When the data has been transferred into the chosen register of the addressed DAC, all DAC registers and outputs can be updated by taking LDAC low. Rev. C | Page 17 of 28 AD5765 Data Sheet 68HC11 1 The remaining data bits in the write sequence are don’t care. During the next SPI write, the data appearing on the SDO output is the data from the previously addressed register. For a read of a single register, the NOP command can be used in clocking out the data from the selected register on SDO. The readback diagram in Figure 4 shows the readback sequence. For example, to read back the fine gain register of Channel A on the AD5765, implement the following sequence: AD57651 MOSI SDIN SCK SCLK PC7 SYNC PC6 LDAC MISO SDO SDIN AD57651 1. SCLK SYNC LDAC SDO 2. SDIN AD57651 SCLK SYNC Write 0xA0XXXX to the AD5765 input register. This configures the AD5765 for read mode with the fine gain register of Channel A selected. Note that all the data bits, DB15 to DB0, are don’t cares. Follow this with a second write, an NOP condition, 0x00XXXX. During this write, the data from the fine gain register is clocked out on the SDO line; that is, data clocked out contains the data from the fine gain register in Bit DB5 to Bit DB0. LDAC SIMULTANEOUS UPDATING VIA LDAC PINS OMITTED FOR CLARITY. Figure 26. Daisy-Chaining the AD5765 Daisy-Chain Operation For systems that contain several devices, the SDO pin can be used to daisy-chain several devices together. This daisy-chain mode can be useful in system diagnostics and in reducing the number of serial interface lines. The first falling edge of SYNC starts the write cycle. The SCLK is continuously applied to the input shift register when SYNC is low. If more than 24 clock pulses are applied, the data ripples out of the shift register and appears on the SDO line. This data is clocked out on the rising edge of SCLK and is valid on the falling edge. By connecting the SDO of the first device to the SDIN input of the next device in the chain, a multidevice interface is constructed. Each device in the system requires 24 clock pulses. Therefore, the total number of clock cycles must equal 24 N, where N is the total number of AD5765 devices in the chain. When the serial transfer to all devices is complete, SYNC is taken high. This latches the input data in each device in the daisy chain and prevents additional data from being clocked into the input shift register. The serial clock can be a continuous or a gated clock. Depending on the status of both SYNC and LDAC, and after data has been transferred into the input register of the DACs, there are two ways in which the DAC registers and DAC outputs can be updated: individually and simultaneously Individual DAC Updating In this mode, LDAC is held low while data is clocked into the input shift register. The addressed DAC output is updated on the rising edge of SYNC. Simultaneous Updating of All DACs In this mode, LDAC is held high while data is clocked into the input shift register. All DAC outputs are updated by taking LDAC low any time after SYNC has been taken high. The update now occurs on the falling edge of LDAC. A continuous SCLK source can be used only if SYNC is held low for the correct number of clock cycles. In gated clock mode, a burst clock containing the exact number of clock cycles must be used, and SYNC must be taken high after the final clock to latch the data. Readback Operation Before a readback operation is initiated, the SDO pin must be enabled by writing to the function register and clearing the SDO disable bit; this bit is cleared by default. Readback mode is invoked by setting the R/W bit to 1 in the serial input register write. With R/W = 1, Bit A2 to Bit A0, in association with Bit REG2, Bit REG1, and Bit REG0, select the register to be read. Rev. C | Page 18 of 28 OUTPUT I/V AMPLIFIER VREFIN LDAC 16-BIT DAC VOUTx DAC REGISTER INPUT REGISTER SCLK SYNC SDIN INTERFACE LOGIC SDO 07249-062 1ADDITIONAL 07249-061 SDO Figure 27. Simplified Serial Interface of Input Loading Circuitry for One DAC Channel Data Sheet AD5765 TRANSFER FUNCTION The output voltage expression for the AD5765 is given by Table 8 shows the ideal input-code-to-output-voltage relationship for the AD5765 for both offset binary and twos complement data coding. D VOUT = −2 × V REFIN + 4 × V REFIN 65,536 where: D is the decimal equivalent of the code loaded to the DAC. VREFIN is the reference voltage applied at the REFAB and REFCD pins. Table 8. Ideal Output Voltage to Input Code Relationship Digital Input Offset Binary Data Coding Analog Output MSB 1111 1000 1000 0111 0000 LSB 1111 0001 0000 1111 0000 VOUTx 2 VREF × (32,767/32,768) 2 VREF × (1/32,768) 0V −2 VREF × (1/32,768) −2 VREF × (32,767/32,768) Twos Complement Data Coding MSB LSB 0111 1111 1111 1111 0000 0000 0000 0001 0000 0000 0000 0000 1111 1111 1111 1111 1000 0000 0000 0000 VOUTx 2 VREF × (32,767/32,768) 2 VREF × (1/32,768) 0V −2 VREF × (1/32,768) −2 VREF × (32,767/32,768) 1111 0000 0000 1111 0000 1111 0000 0000 1111 0000 ASYNCHRONOUS CLEAR (CLR) CLR is a negative edge triggered clear that allows the outputs to be cleared to either 0 V (twos complement coding) or negative full scale (offset binary coding). It is necessary to maintain CLR low for a minimum amount of time (see Figure 2) for the operation to complete. When the CLR signal is returned high, the output remains at the cleared value until a new value is programmed. If, at power-on, CLR is at 0 V, then all DAC outputs are updated with the clear value. A clear can also be initiated through software by writing the command 0x04XXXX to the AD5765. Table 9. AD5765 Input Register Format MSB DB23 R/W LSB DB22 0 DB21 REG2 DB20 REG1 DB19 REG0 DB18 A2 DB17 A1 DB16 A0 DB15:DB0 Data Table 10. Input Register Bit Functions Bit R/W Description Indicates a read from or a write to the addressed register REG2, REG1, REG0 Used in association with the address bits to determine if a read or write operation is to the data register, offset register, gain register, or function register REG2 REG1 REG0 Function 0 0 0 Function register 0 1 0 Data register 0 1 1 Coarse gain register 1 0 0 Fine gain register 1 0 1 Offset register Used to decode the DAC channels A2 A1 A0 Channel Address 0 0 0 DAC A 0 0 1 DAC B 0 1 0 DAC C 0 1 1 DAC D 1 0 0 All DACs Data bits A2, A1, A0 D15:D0 Rev. C | Page 19 of 28 AD5765 Data Sheet FUNCTION REGISTER The function register is addressed by setting the three REG bits to 000. The values written to the address bits and the data bits determine the function addressed. The functions available via the function register are outlined in Table 11 and Table 12. Table 11. Function Register Options REG2 0 0 REG1 0 0 REG0 0 0 A2 0 0 A1 0 0 A0 0 1 0 0 0 0 0 0 1 1 0 0 0 1 DB15:DB6 Don’t care DB5 DB4 DB3 DB2 No operation, data = don’t care Local ground D1 D1 D0 offset adjustment direction value direction DB1 DB0 D0 value SDO disable Clear, data = don’t care Load, data = don’t care Table 12. Explanation of Function Register Options Option NOP Local Ground Offset Adjustment D0/D1 Direction D0/D1 Value SDO Disable Clear Load Description No operation instruction used in readback operations. Set by the user to enable the local ground offset adjustment function. Cleared by the user to disable the local ground offset adjustment function (default). See the Design Features section for additional details. Set by the user to enable D0/D1 as outputs. Cleared by the user to enable D0/D1 as inputs (default). See the Design Features section for additional details. I/O port status bits. Logic values written to these locations determine the logic outputs on the D0 and D1 pins when configured as outputs. These bits indicate the status of the D0 and D1 pins when the I/O port is active as an input. When enabled as inputs, these bits are don’t cares during a write operation. Set by the user to disable the SDO output. Cleared by the user to enable the SDO output (default). Addressing this function resets the DAC outputs to 0 V in twos complement mode and negative full scale in binary mode. Addressing this function updates the DAC registers and, consequently, the analog outputs. DATA REGISTER The data register is addressed by setting the three REG bits to 010. The DAC address bits select the DAC channel with which the data transfer is to take place (see Table 10). The data bits are in the DB15 to DB0 positions, as shown in Table 13. Table 13. Programming the AD5765 Data Register REG2 0 REG1 1 REG0 0 A2 A1 DAC address A0 DB15:DB0 16-bit DAC data COARSE GAIN REGISTER The coarse gain register is addressed by setting the three REG bits to 011. The DAC address bits select the DAC channel with which the data transfer is to take place (see Table 10). The coarse gain register is a 2-bit register and allows the user to select the output range of each DAC, as shown in Table 14 and Table 15. Table 14. Programming the AD5765 Coarse Gain Register REG2 0 REG1 1 REG0 1 A2 A1 A0 DAC address DB15:DB2 Don’t care DB1 CG1 Table 15. Output Range Selection Output Range ±4.096 V (default) ±4.20103 V ±4.31158 V CG1 0 0 1 Rev. C | Page 20 of 28 CG0 0 1 0 DB0 CG0 Data Sheet AD5765 FINE GAIN REGISTER The fine gain register is addressed by setting the three REG bits to 100. The DAC address bits select the DAC channel with which the data transfer is to take place (see Table 10). The fine gain register is a 6-bit register and allows the user to adjust the gain of each DAC channel by −32 LSBs to +31 LSBs in 1 LSB increments as shown in Table 16 and Table 17. The adjustment is made to both the positive full-scale and negative full-scale points simultaneously, each point being adjusted by ½ of one step. The fine gain register coding is twos complement. Table 16. Programming AD5765 Fine Gain Register REG2 1 REG1 0 REG0 0 A2 A1 A0 DAC address DB15:DB6 Don’t care DB5 FG5 DB4 FG4 DB3 FG3 DB2 FG2 DB1 FG1 DB0 FG0 Table 17. AD5765 Fine Gain Register Options Gain Adjustment +31 LSBs +30 LSBs … No Adjustment (Default) … −31 LSBs −32 LSBs FG5 0 0 … 0 … 1 1 FG4 1 1 … 0 … 0 0 FG3 1 1 … 0 … 0 0 FG2 1 1 ... 0 … 0 0 FG1 1 1 … 0 … 0 0 FG0 1 0 … 0 … 1 0 OFFSET REGISTER The offset register is addressed by setting the three REG bits to 101. The DAC address bits select the DAC channel with which the data transfer is to take place (see Table 10). The AD5765 offset register is an 8-bit register and allows the user to adjust the offset of each channel by −16 LSBs to +15.875 LSBs in increments of ⅛ LSB as shown in Table 18 and Table 19. The offset register coding is twos complement. Table 18. Programming the AD5765 Offset Register REG2 1 REG1 0 REG0 1 A2 A1 A0 DAC address DB15:DB8 Don’t care DB7 OF7 DB6 OF6 DB5 OF5 DB4 OF4 DB3 OF3 DB2 OF2 DB1 OF1 Table 19. AD5765 Offset Register Options Offset Adjustment +15.875 LSBs +15.75 LSBs … No Adjustment (Default) … −15.875 LSBs −16 LSBs OF7 0 0 … 0 … 1 1 OF6 1 1 … 0 … 0 0 OF5 1 1 … 0 … 0 0 Rev. C | Page 21 of 28 OF4 1 1 … 0 … 0 0 OF3 1 1 … 0 … 0 0 OF2 1 1 … 0 … 0 0 OF1 1 1 … 0 … 0 0 OF0 1 0 … 0 … 1 0 DB0 OF0 AD5765 Data Sheet 2. OFFSET AND GAIN ADJUSTMENT WORKED EXAMPLE Using the information provided in the Theory of Operation section, the following worked example demonstrates how the AD5765 functions can be used to eliminate both offset and gain errors. Because the AD5765 is factory calibrated, offset and gain errors should be negligible. However, errors can be introduced by the system that the AD5765 is operating within; for example, a voltage reference value that is not equal to 2.048 V introduces a gain error. An output range of ±4.096 V and twos complement data coding are assumed. Removing Offset Error The AD5765 can eliminate an offset error in the range of −2 mV to +1.98 mV with a step size of ⅛ of a 16-bit LSB. 1. 2. 3. 11011000 is the value that should be programmed to the offset register. Note that this twos complement conversion is not necessary in the case of a positive offset adjustment. The value to be programmed to the offset register is simply the binary representation of the adjustment value. Removing Gain Error The AD5765 can eliminate a gain error at negative full-scale output in the range of −2 mV to +1.94 mV with a step size of ½ of a 16-bit LSB. 1. Calculate the step size of the offset adjustment. Offset Adjust Step Size = Convert the binary number to a negative twos complement number by inverting all bits and adding 1: 11011000. Calculate the step size of the gain adjustment. Gain Adjust Step Size = 8.192 = 15.625 μV 216 × 8 2. Measure the offset error by programming 0x0000 to the data register and measuring the resulting output voltage; for this example, the measured value is 614 µV. Calculate the number of offset adjustment steps that this value represents. 614 μV Measured Offset Value = = 13 Steps Number of Steps = 15.625 μV Offset Step Size 3. 8.192 = 62.5 μV 216 × 2 Measure the gain error by programming 0x8000 to the data register and measuring the resulting output voltage. The gain error is the difference between this value and −4.096 V; for this example, the gain error is −0.8 mV. Calculate how many gain adjustment steps this value represents. Number of Steps = Measured Gain Value 0.8 mV = = 13 Steps 62.5 μV Gain Step Size The offset error measured is positive; therefore, a negative adjustment of 40 steps is required. The offset register is 8-bits wide and the coding is twos complement. The gain error measured is negative (in terms of magnitude); therefore, a positive adjustment of 13 steps is required. The gain register is six bits wide and the coding is twos complement. The required gain register value can be determined as follows: The required offset register value can be calculated as follows: 1. 1. Convert the adjustment value to binary: 00101000. Convert the adjustment value to binary: 001101. The value to be programmed to the gain register is simply this binary number. Rev. C | Page 22 of 28 Data Sheet AD5765 DESIGN FEATURES ANALOG OUTPUT CONTROL In many industrial process control applications, it is vital that the output voltage be controlled during power-up and during brownout conditions. When the supply voltages are changing, the output pins are clamped to 0 V via a low impedance path. To prevent the output amp being shorted to 0 V during this time, transmission gate G1 is also opened (see Figure 28). These conditions are maintained until the power supplies stabilize and a valid word is written to the DAC register. At this time, G2 opens and G1 closes. Both transmission gates are also externally controllable via the reset logic (RSTIN) control input. For instance, if RSTIN is driven from a battery supervisor chip, the RSTIN input is driven low to open G1 and close G2 on power-down or during a brownout. Conversely, the on-chip voltage detector output (RSTOUT) is also available to the user to control other parts of the system. The basic transmission gate functionality is shown in Figure 28. RSTOUT RSTIN VOLTAGE MONITOR AND CONTROL G1 VOUTA AGNDA 07249-063 G2 If the ISCC pin is left unconnected, the short-circuit current limit defaults to 5 mA. It should be noted that limiting the short-circuit current to a small value can affect the slew rate of the output when driving into a capacitive load; therefore, the value of the short-circuit current programmed should take into account the size of the capacitive load being driven. DIGITAL I/O PORT The AD5765 contains a 2-bit digital I/O port (D1 and D0). These bits can be configured as inputs or outputs independently and can be driven or have their values read back via the serial interface. The I/O port signals are referenced to DVCC and DGND. When configured as outputs, they can be used as control signals to multiplexers or can be used to control calibration circuitry elsewhere in the system. When configured as inputs, the logic signals from limit switches, for example, can be applied to D0 and D1 and can be read back via the digital interface. DIE TEMPERATURE SENSOR The on-chip die temperature sensor provides a voltage output that is linearly proportional to the centigrade temperature scale. Its nominal output voltage is 1.44 V at +25°C die temperature, varying at 3 mV/°C and resulting in a typical output range of 1.175 V to 1.9 V over the full temperature range. Its low output impedance and linear output simplify interfacing to temperature control circuitry and ADCs. The temperature sensor is provided as more of a convenience than a precise feature; it is intended to indicate a die temperature change for recalibration purposes. LOCAL-GROUND-OFFSET ADJUSTMENT Figure 28. Analog Output Control Circuitry DIGITAL OFFSET AND GAIN CONTROL The AD5765 incorporates a digital offset adjustment function with a ±16 LSB adjustment range and 0.125 LSB resolution. The gain register allows the user to adjust the AD5765 full-scale output range. The full-scale output can be programmed to achieve full-scale ranges of ±4.096 V, ±4.201 V, and ±4.311 V. A fine gain trim is also provided. PROGRAMMABLE SHORT-CIRCUIT PROTECTION The AD5765 incorporates a local-ground-offset adjustment feature that, when enabled in the function register, adjusts the DAC outputs for voltage differences between the individual DAC ground pins and the REFGND pin, ensuring that the DAC output voltages are always referenced with respect to the local DAC ground pin. For instance, if Pin AGNDA is at +5 mV with respect to the REFGND pin and VOUTA is measured with respect to AGNDA, a −5 mV error results, enabling the localground-offset adjustment feature to adjust VOUTA by +5 mV, thereby eliminating the error. The short-circuit current of the output amplifiers can be programmed by inserting an external resistor between the ISCC pin and PGND. The programmable range for the current is 500 µA to 10 mA, corresponding to a resistor range of 120 kΩ to 6 kΩ. The resistor value is calculated as follows: R≈ 60 I SC Rev. C | Page 23 of 28 AD5765 Data Sheet POWER-ON STATUS The AD5765 has multiple power supply and digital input pins. It is important to consider the sequence in which the pins are powered up to ensure that the AD5765 powers on in the required state. The outputs power on either clamped to AGNDx, driving 0 V, or driving negative full-scale output (−4.096 V), depending on how the BIN/2sCOMP, CLR, and LDAC pins are configured during power-up. The CLR pin, if connected to DGND, causes the DAC registers to be loaded with 0x0000 and the outputs to be updated; consequently, the outputs are loaded with 0 V if BIN/2sCOMP is connected to DGND or with negative full-scale (−4.096 V) if BIN/2sCOMP is connected to DVCC, corresponding respectively to the twos complement and binary voltages for the digital code 0x0000. During power-up, the state of the LDAC pin has an identical effect to that of the CLR pin. If both the CLR and LDAC pins are connected to DVCC during power-up, the outputs power on clamped to AGNDx and remain so until a valid write is made to the device. Table 20 outlines the possible output power-on states. Table 20. Output Power-On States BIN/2sCOMP DGND DGND DGND DGND DVCC DVCC DVCC DVCC Rev. C | Page 24 of 28 CLR LDAC VOUT at Power-On DGND DGND DVCC DVCC DGND DGND DVCC DVCC DGND DVCC DGND DVCC DGND DVCC DGND DVCC 0V 0V 0V Clamped to AGNDx −4.096 V −4.096 V −4.096 V Clamped to AGNDx Data Sheet AD5765 APPLICATIONS INFORMATION TYPICAL OPERATING CIRCUIT PRECISION VOLTAGE REFERENCE SELECTION Figure 29 shows the typical operating circuit for the AD5765. The only external components needed for this precision 16-bit DAC are a reference voltage source, decoupling capacitors on the supply pins and reference inputs, and an optional shortcircuit current setting resistor. Because the device incorporates reference buffers, it eliminates the need for an external bipolar reference and associated buffers. This leads to an overall savings in both cost and board space. To achieve the optimum performance from the AD5765 over its full operating temperature range, a precision voltage reference must be used. Thought should be given to the selection of a precision voltage reference. The AD5765 has two reference inputs, REFAB and REFCD. The voltages applied to the reference inputs are used to provide a buffered positive and negative reference for the DAC cores. Therefore, any error in the voltage reference is reflected in the outputs of the device. In Figure 29, AVDD is connected to +5 V and AVSS is connected to −5 V. In Figure 29, AGNDx is connected to REFGND. There are four possible sources of error to consider when choosing a voltage reference for high accuracy applications: initial accuracy, temperature coefficient of the output voltage, long-term drift, and output voltage noise. +5V 10µF ADR420 100nF 2 VOUT 6 GND VIN Initial accuracy error on the output voltage of an external reference may lead to a full-scale error in the DAC. Therefore, to minimize these errors, a reference with low initial accuracy error specification is preferred. Choosing a reference with an output trim adjustment, such as the ADR430, allows a system designer to trim system errors out by setting the reference voltage to a voltage other than the nominal. The trim adjustment can also be used at temperature to trim out any error. 4 +5V –5V 10µF 10µF 100nF 100nF 100nF BIN/2sCOMP 1 SYNC SCLK 2 SCLK SDIN 3 SDIN SDO 4 SDO REFAB NC REFCD AVSS TEMP AVDD REFGND SYNC BIN/2sCOMP 32 31 30 29 28 27 26 25 +5V VOUTA 23 VOUTA VOUTB 22 VOUTB AGNDB 21 AD5765 AGNDC 20 LDAC VOUTC 19 VOUTC D0 7 D0 VOUTD 18 VOUTD D1 8 D1 AGNDD 17 10µF ISCC AVSS PGND The temperature coefficient of a reference output voltage affects INL, DNL, and TUE. A reference with a tight temperature coefficient specification should be chosen to reduce the dependence of the DAC output voltage on ambient conditions. 10µF 100nF 100nF RSTIN AVDD 10 11 12 13 14 15 16 DVCC 9 DGND RSTIN CLR 6 RSTOUT 5 LDAC RSTOUT Long-term drift is a measure of how much the reference output voltage drifts over time. A reference with a tight long-term drift specification ensures that the overall solution remains relatively stable over its entire lifetime. AGNDA 24 100nF NC = NO CONNECT +5V –5V 07249-035 10µF +5V Figure 29. Typical Operating Circuit In high accuracy applications (which have a relatively low noise budget), reference output voltage noise needs to be considered. Choosing a reference with as low an output noise voltage as practical for the system resolution required is important. Precision voltage references such as the ADR420 (XFET® design) produce low output noise in the 0.1 Hz to 10 Hz region. However, as the circuit bandwidth increases, filtering the output of the reference may be required to minimize the output noise. Table 21. Some Precision References Recommended for Use with the AD5765 Part No. ADR430 ADR420 Initial Accuracy (mV Max) ±1 ±1 Long-Term Drift (ppm Typ) 40 50 Temp Drift (ppm/°C Max) 3 3 Rev. C | Page 25 of 28 0.1 Hz to 10 Hz Noise (µV p-p Typ) 3.5 1.75 AD5765 Data Sheet LAYOUT GUIDELINES The power supply lines of the AD5765 should use as large a trace as possible to provide low impedance paths and reduce the effects of glitches on the power supply line. Fast switching signals, such as clocks, should be shielded with digital ground to avoid radiating noise to other parts of the board and should never be run near the reference inputs. A ground line routed between the SDIN and SCLK lines helps reduce crosstalk between them (this is not required on a multilayer board, which has a separate ground plane; however, it is helpful to separate the lines). It is essential to minimize noise on the reference inputs because such noise couples through to the DAC output. Avoid crossover of digital and analog signals. Traces on opposite sides of the board should run at right angles to each other. This reduces the effects of feedthrough on the board. A microstrip technique is recommended but not always possible with a double-sided board. In this technique, the component side of the board is dedicated to the ground plane, and signal traces are placed on the solder side. isolated interfaces because the number of interface lines is kept to a minimum. Figure 30 shows a 4-channel isolated interface to the AD5765 using an ADuM1400. For more information, go to www.analog.com. MICROCONTROLLER ADuM14001 VIA SERIAL DATA OUT VIB VIC SYNC OUT CONTROL OUT 1ADDITIONAL VID ENCODE DECODE ENCODE DECODE ENCODE DECODE ENCODE DECODE VOA TO SCLK VOB TO SDIN VOC TO SYNC VOD TO LDAC PINS OMITTED FOR CLARITY. 07249-065 SERIAL CLOCK OUT Figure 30. Isolated Interface MICROPROCESSOR INTERFACING Microprocessor interfacing to the AD5765 is via a serial bus that uses a standard protocol that is compatible with microcontrollers and DSP processors. The communications channel is a 3-wire (minimum) interface consisting of a clock signal, a data signal, and a synchronization signal. The AD5765 requires a 24-bit data-word with data valid on the falling edge of SCLK. For all the interfaces, the DAC output update can be done automatically when all the data is clocked in, or it can be done under the control of LDAC. The contents of the DAC register can be read using the readback function. AD5765 to Blackfin DSP Interface Figure 31 shows how the AD5765 can be interfaced to an Analog Devices, Inc., Blackfin® DSP. The Blackfin has an integrated SPI port that can be connected directly to the SPI pins of the AD5765 and programmable I/O pins that can be used to set the state of a digital input such as the LDAC pin. GALVANICALLY ISOLATED INTERFACE In many process control applications, it is necessary to provide an isolation barrier between the controller and the unit being controlled to protect and isolate the controlling circuitry from any hazardous common-mode voltages that may occur. Isocouplers provide voltage isolation in excess of 2.5 kV. The serial loading structure of the AD5765 makes it ideal for Rev. C | Page 26 of 28 ADSP-BF531 AD57651 SPISELx SYNC SCK SCLK MOSI SDIN PF10 LDAC 1ADDITIONAL PINS OMITTED FOR CLARITY. Figure 31. AD5765 to Blackfin Interface 07249-037 For any circuit in which accuracy is important, careful consideration of the power supply and ground return layout helps to ensure the rated performance. The printed circuit board on which the AD5765 is mounted should be designed so that the analog and digital sections are separated and confined to certain areas of the board. If the AD5765 is in a system in which multiple devices require an AGND-to-DGND connection, the connection should be made at one point only. The star ground point should be established as close as possible to the device. The AD5765 should have ample supply bypassing of 10 µF in parallel with 0.1 µF on each supply located as close to the package as possible, ideally right up against the device. The 10 µF capacitors are the tantalum bead type. The 0.1 µF capacitor should have low effective series resistance (ESR) and low effective series inductance (ESI) such as the common ceramic types, which provide a low impedance path to ground at high frequencies to handle transient currents due to internal logic switching. Data Sheet AD5765 OUTLINE DIMENSIONS 0.75 0.60 0.45 1.20 MAX 9.00 BSC SQ 25 32 24 1 PIN 1 7.00 BSC SQ TOP VIEW (PINS DOWN) 0° MIN 0.15 0.05 0.20 0.09 7° 3.5° 0° 0.08 MAX COPLANARITY SEATING PLANE 17 8 16 9 VIEW A VIEW A 0.80 BSC LEAD PITCH ROTATED 90° CCW 0.45 0.37 0.30 COMPLIANT TO JEDEC STANDARDS MS-026-AB A 020607-A 1.05 1.00 0.95 Figure 32. 32-Lead Thin Plastic Quad Flat Package [TQFP] (SU-32-2) Dimensions shown in millimeters ORDERING GUIDE Model 1 AD5765BSUZ AD5765BSUZ-REEL7 AD5765CSUZ AD5765CSUZ-REEL7 EVAL-AD5765EBZ 1 INL ± 2 LSB ± 2 LSB ± 1 LSB ± 1 LSB Temperature Range −40°C to +105°C −40°C to +105°C −40°C to +105°C −40°C to +105°C Z = RoHS Compliant Part. Rev. C | Page 27 of 28 Package Description 32-Lead TQFP 32-Lead TQFP 32-Lead TQFP 32-Lead TQFP Evaluation Board Package Option SU-32-2 SU-32-2 SU-32-2 SU-32-2 AD5765 Data Sheet NOTES ©2009–2011 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D07249-0-10/11(C) Rev. C | Page 28 of 28