4M × 72-Bit Dynamic RAM Module (ECC - Module ) HYM 72V4000GS-50/-60 HYM 72V4010GS-50/-60 • 168 pin 4 194 304 words by 72-bit ECC - mode organization for PC main memory applications • Fast access and cycle time 50 ns access time 90 ns cycle time (-50 version) 60 ns access time 110 ns cycle time (-60 version) • Fast page mode capability with 35 ns cycle time (-50 version) 40 ns cycle time (-60 version) • Single + 3.3V (± 0.3V) supply • Low power dissipation max. 6480 mW active (-50 version) max. 5832 mW active (-60 version) CMOS – 108 mW standby LVTTL – 180 mW standby • CAS-before-RAS refresh, RAS-only-refresh • Decoupling capacitors mounted on substrate • All inputs, outputs and clock fully LVTTL & LVCMOS compatible • 4 Byte interleave enabled, Dual Address inputs (A0/B0) • Buffered inputs excepts RAS and DQ • 168 pin, dual read-out, Single in-Line Memory Module • Utilizes eighteen 4M × 4 -DRAMs and four BiCMOS 8-bit buffers/line drivers LV244A • Two versions : HYM 72V4000GS with TSOPII-components (4 mm thickness) HYM 72V4010GS with SOJ-components (9 mm thickness) • 4096 refresh cycles / 64 ms with 12 / 10 addressing • Gold contact pad • Double sided module with 25.35 mm (1000 mil) height Semiconductor Group 1 11.95 HYM72V4000/10GS-50/-60 4M x 72-ECC Module The HYM 72V4000/10GS-50/-60 is a 32 MByte DRAM module organized as 4 194 430 words by 72bit in a 168-pin, dual read-out, single-in-line package comprising eighteen HYB 3116400BT/BJ 4M × 4 DRAMs in 300 mil wide TSOPII or SOJ- packages mounted together with ceramic decoupling capacitors on a PC board. All inputs except RAS and DQ are buffered by using BiCMOS buffers/line drivers. Each HYB 3116400BT/BJ is described in the data sheet and is fully electrically tested and processed according to Siemens standard quality procedure prior to module assembly. After assembly onto the board, a further set of electrical tests is performed. The density and speed of the module can be detected by the use of presence detect pins. Ordering Information Type Ordering Code HYM 72V4000GS-50 HYM 72V4000GS-60 Q67100-Q2077 HYM 72V4010GS-50 HYM 72V4010GS-60 Q67100-Q2078 Package Descriptions L-DIM-168-5 3.3V 50ns DRAM module L-DIM-168-5 3.3V 60ns DRAM module L-DIM-168-5 3.3V 50ns DRAM module L-DIM-168-5 3.3V 60ns DRAM module Pin Names A0-A11,B0 DQ0 - DQ71 RAS0, RAS2 CAS0 , CAS2 WE0, WE2 OE0, OE2 Vcc Vss PD1 - PD8 PDE ID0 , ID1 N.C. Address Input Data Input/Output Row Address Strobe Column Address Strobe Read / Write Input Output Enable Power (+3.3 Volt) Ground Presence Detect Pins Presence Detect Enable ID indentification bit No Connection Presence-Detect and ID-pin Truth Table: Module ID0 ID1 PD1 PD2 PD3 PD4 PD5 PD6 PD7 PD8 HYM 72V4000GS-50 Vss Vss 1 1 0 1 0 0 0 0 HYM 72V4000GS-60 Vss Vss 1 1 0 1 0 1 1 0 Note: 1 = High Level ( Driver Output) , 0 = Low Level (Driver Output) for PDE active ( ground) . For PDE at a high level all PD terminal are in tri-state. Semiconductor Group 2 HYM72V4000/10GS-50/-60 4M x 72-ECC Module Pin Configuration PIN # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 Symbol VSS DQ0 DQ1 DQ2 DQ3 VCC DQ4 DQ5 DQ6 DQ7 DQ8 VSS DQ9 DQ10 DQ11 DQ12 DQ13 VCC DQ14 DQ15 DQ16 DQ17 VSS NC NC VCC WE0 CAS0 NC RAS0 OE0 VSS A0 A2 A4 A6 A8 A10 NC VCC NC NC Semiconductor Group PIN # 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 Symbol PIN # VSS OE2 RAS2 CAS4 NC WE2 VCC NC NC DQ18 DQ19 VSS DQ20 DQ21 DQ22 DQ23 VCC DQ24 NC NC NC NC DQ25 DQ26 DQ27 VSS DQ28 DQ29 DQ30 DQ31 VCC DQ32 DQ33 DQ34 DQ35 VSS PD1 PD3 PD5 PD7 ID0 (VSS) VCC 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 3 Symbol VSS DQ36 DQ37 DQ38 DQ39 VCC DQ40 DQ41 DQ42 DQ43 DQ44 VSS DQ45 DQ46 DQ47 DQ48 DQ49 VCC DQ50 DQ51 DQ52 DQ53 VSS NC NC VCC NC NC NC NC NC VSS A1 A3 A5 A7 A9 A11 NC VCC NC B0 PIN # 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 Symbol VSS NC NC NC NC PDE VCC NC NC DQ54 DQ55 VSS DQ56 DQ57 DQ58 DQ59 VCC DQ60 NC NC NC NC DQ61 DQ62 DQ63 VSS DQ64 DQ65 DQ66 DQ67 VCC DQ68 DQ69 DQ70 DQ71 VSS PD2 PD4 PD6 PD8 ID1 (VSS) VCC HYM72V4000/10GS-50/-60 4M x 72-ECC Module RAS0 CAS0 RAS2 CAS4 WE0 OE0 WE2 OE2 DQ0-DQ3 DQ36-DQ39 I/O1-I/O4 I/O1-I/O4 D0 DQ4-DQ7 D9 I/O1-I/O4 I/O1-I/O4 DQ40-DQ43 D1 DQ8-DQ11 D10 I/O1-I/O4 DQ44-DQ47 I/O1-I/O4 D2 DQ12-DQ15 D11 I/O1-I/O4 I/O1-I/O4 DQ48-DQ51 D3 DQ16-DQ19 D12 I/O1-I/O4 I/O1-I/O4 DQ52-DQ55 D4 DQ20-DQ23 D13 DQ56-DQ59 I/O1-I/O4 I/O1-I/O4 D5 DQ24-DQ27 D14 I/O1-I/O4 I/O1-I/O4 DQ60-DQ63 D6 DQ28-DQ31 D15 DQ64-DQ67 I/O1-I/O4 I/O1-I/O4 D7 DQ32-DQ35 D16 I/O1-I/O4 I/O1-I/O4 DQ68-DQ71 D8 D17 A0 D0 - D8 Vcc B0 D9 - D17 Vss A1-A11 D0 - D17 PDE Vcc or Vss Block Diagram Semiconductor Group 4 D0-D17, buffers PD1-PD8 HYM72V4000/10GS-50/-60 4M x 72-ECC Module Absolute Maximum Ratings Operating temperature range ......................................................................................... 0 to + 70 °C Storage temperature range...................................................................................... – 55 to + 125 °C Input/output voltage ............................................................................... -0.5 to min (Vcc+0.5, 4.6) V Power supply voltage................................................................................................... – 1 to + 4.6 V Power dissipation.................................................................................................................... 8.3 W Data out current (short circuit) ................................................................................................ 50 mA Note: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. DC Characteristics TA = 0 to 70 °C; VCC = 3.3 V ± 0.3V Parameter Symbol Limit Values min. max. Unit Test Condition Input high voltage VIH 2.0 Vcc+0.5 V 1) Input low voltage VIL – 1.0 0.8 V 1) Output high voltage (LVTTL) Output „H“ voltage level ( IOUT = – 2 mA) VOH 2.4 – V 1) Output low voltage (LVTTL) Output „L“ voltage level ( IOUT = 2 mA) VOL – 0.4 V 1) Output high voltage (LVCMOS) Output „H“voltage level ( IOUT = – 100 µA) VOH Vcc-0.2 – V 1) Output low voltage (LVCMOS) Output „L“ voltage level ( IOUT = 100 µA) VOL – 0.2 V 1) Input leakage current (0 V < VIN < Vcc, all other pins = 0 V) II(L) – 20 20 µA 1) Output leakage current (DO is disabled, 0 V < VOUT < Vcc) IO(L) – 20 20 µA 1) – – 1800 1620 mA mA 2)3)4) – 50 mA – Average VCC supply current: ICC1 -50 version -60 version (RAS, CAS, address cycling, tRC = tRC min.) Standby VCC supply current (RAS = CAS =2.4V, one address change within 15,6 µs trc) ICC2 Semiconductor Group 5 HYM72V4000/10GS-50/-60 4M x 72-ECC Module Parameter Symbol Average VCC supply current during RAS ICC3 only refresh cycles: -50 version -60 version Limit Values Unit Test Condition min. max. – – 1800 1620 mA mA – – – 720 630 mA mA 2)3)4) – 30 mA – – – 1800 1620 mA mA 2)4) 2)4) (RAS cycling, CAS = VIH , t RC = tRC min.) ICC4 Average VCC supply current during fast page mode: -50 version -60 version (RAS = VIL, CAS, address cycling tPC = tPC min.) Standby VCC supply current (RAS = CAS = VCC – 0.2 V, one address change within 15,6 µs trc) ICC5 Average VCC supply current during CAS-before-RAS refresh mode: ICC6 -50 version -60 version (RAS, CAS cycling, tRC = tRC min.) Capacitance TA = 0 to 70 °C; VCC = 3.3 V ± 0.3V; f = 1 MHz Parameter Symbol Limit Values min. max. Unit Input capacitance (A0 to A11,B0) CI1 – 10 pF Input capacitance (RAS0, RAS2) CI2 – 50 pF Input capacitance (CAS0-CAS7) CI3 – 15 pF Input capacitance (WE0,WE2,OE0,OE2) CI4 – 15 pF I/O capacitance (DQ0-DQ71) CIO1 – 15 pF Semiconductor Group 6 HYM72V4000/10GS-50/-60 4M x 72-ECC Module AC Characteristics (note: 5,6,7,8) TA = 0 to 70 °C,VCC = 3.3 ± 0.3 V Parameter Symbol -50 -60 min. max. min. max. Unit Note common parameters Random read or write cycle time tRC 90 – 110 – ns RAS precharge time tRP 30 – 40 – ns RAS pulse width tRAS 50 100k 60 100k ns CAS pulse width tCAS 13 100k 15 100k ns Row address setup time tASR 5 – 5 – ns 9 Row address hold time tRAH 8 – 8 – ns 10 Column address setup time tASC 2 – 2 – ns 11 Column address hold time tCAH 15 – 15 – ns 9 RAS to CAS delay time tRCD 16 32 18 40 RAS to column address delay time tRAD 11 20 13 25 ns 12 RAS hold time tRSH 18 – 20 – ns 9 CAS hold time tCSH 48 – 58 – ns 10 CAS to RAS precharge time tCRP 10 – 10 – ns 9 Transition time (rise and fall) tT 3 30 3 30 ns 7 Refresh period tREF – 64 – 64 ms Access time from RAS tRAC – 50 – 60 ns 13,14 Access time from CAS tCAC – 18 – 20 ns 9,13,14 Access time from column address tAA – 30 – 35 ns 9,13, 15 OE access time tOEA – 18 – 20 ns 9,13 Column address to RAS lead time tRAL 30 – 35 – ns 9 Read command setup time tRCS 2 – 2 – ns 11 Read command hold time tRCH 2 – 2 – ns 11,16 Read command hold time referenced to RAS tRRH 0 – 0 – ns 16 tCLZ 2 – 2 – ns 11,13 tOFF – 18 – 20 ns 9,17 12 Read Cycle CAS to output in low-Z Output buffer turn-off delay Semiconductor Group 7 HYM72V4000/10GS-50/-60 4M x 72-ECC Module AC Characteristics (cont’d) (note: 5,6,7,8) TA = 0 to 70 °C,VCC = 3.3 ± 0.3 V Parameter Symbol -50 -60 min. max. min. max. Unit Note Output buffer turn-off delay from OE tOEZ – 18 – 20 ns 9,17 CAS delay time from Din tDZC 0 – 0 – ns 18 Data to OE low delay tDZO 0 – 0 – ns 18 CAS high to data delay tCDD 18 – 20 – ns 9,19 OE high to data delay tODD 18 – 20 – ns 9,19 Write command hold time tWCH 13 – 15 – ns 9 Write command pulse width tWP 8 – 10 – ns Write command setup time tWCS 2 – 2 – ns 11,20 Write command to RAS lead time tRWL 18 – 20 – ns 9 Write command to CAS lead time tCWL 13 – 15 – ns Data setup time tDS -2 – -2 – ns 10,21 Data hold time tDH 15 – 15 – ns 9,21 Read-write cycle time tRWC 131 – 155 – ns 9 RAS to WE delay time tRWD 70 – 82 – ns 11,21 CAS to WE delay time tCWD 33 – 37 – ns 11,21 Column address to WE delay time tAWD 45 – 52 – ns 11,21 OE command hold time tOEH 11 – 13 – ns 10 Fast page mode cycle time tPC 35 – 40 – ns CAS precharge time tCP 10 – 10 – ns Access time from CAS precharge tCPA – 35 – 40 ns tRAS 50 200k 60 200k ns tRHCP 35 – 40 – ns Write Cycle Read-Modify-Write Cycle Fast Page Mode Cycle RAS pulse width CAS precharge to RAS Delay Semiconductor Group 8 9,13 9 HYM72V4000/10GS-50/-60 4M x 72-ECC Module AC Characteristics (cont’d) (note: 5,6,7,8) TA = 0 to 70 °C,VCC = 3.3 ± 0.3 V Parameter Symbol -50 -60 min. max. min. max. Unit Note Fast Page Mode Read-Modify-Write Cycle Fast page mode read-write cycle time tPRWC 73 – 82 – ns 11 CAS precharge to WE tCPWD 50 – 57 – ns 11,21 CAS setup time tCSR 7 – 7 – ns 11 CAS hold time tCHR 8 – 8 – ns 10 RAS to CAS precharge time tRPC 5 – 5 – ns Write to RAS precharge time tWRP 12 – 12 – ns 11 Write hold time referenced to RAS tWRH 8 – 8 – ns 10 PDE to valid presence detect data tPD – 10 – 10 ns PDE inactive to presence detects inactive tPDOFF 0 10 0 10 ns CAS-before-RAS Refresh Cycle Presence Detect Read Cycle Semiconductor Group 9 HYM72V4000/10GS-50/-60 4M x 72-ECC Module Notes: 1) 2) 3) 4) All voltages are referenced to VSS. ICC1, ICC3, ICC4 and ICC6 depend on cycle rate. ICC1 and ICC4 depend on output loading. Specified values are measured with the output open. Address can be changed once or less while RAS = Vil.In the case of ICC4 it can be changed once or less during a fast page mode cycle ( tpc). 5) An initial pause of 100 µs is required after power-up followed by 8 RAS-only-refresh cycles, before proper device operation is achieved. In case of using internal refresh counter, a minimum of 8 CAS-before-RAS initialization cycles instead of 8 RAS cycles are required. 6) AC measurements assume tT = 5 ns. 7) VIH (min.) and VIL (max.) are reference levels for measuring timing of input signals. Also, transition times are measured between VIH and VIL. 8) The specified timings include buffer, loading and skew delay adders: 2ns minimum, 5ns (CAS, WE, OE, addresses) maximum delay, no pulse shrinkage to the DRAM device timings. The data and RAS signals are not buffered, which preserves the DRAMs access specification of 50ns and 60ns. 9) A +5ns timing skew from the DRAM to the module resulted from the addition of line drivers. 10) A -2ns timing skew from the DRAM to the module resulted from the addition of line drivers. 11) A +2ns timing skew from the DRAM to the module resulted from the addition of line drivers. 12) A -2ns (min.) and a -5ns (max.) timing skew from the DRAM to the module resulted from the addition of line drivers. 13) Measured with the specified current load and 100 pF at Voh = 2.0 V and Vol = 0.8 V. 14) Operation within the tRCD (max.) limit ensures that tRAC (max.) can be met. tRCD (max.) is specified as a reference point only: If tRCD is greater than the specified tRCD (max.) limit, then access time is controlled by tCAC. 15) Operation within the tRAD (max.) limit ensures that tRAC (max.) can be met. tRAD (max.) is specified as a reference point only: If tRAD is greater than the specified tRAD (max.) limit, then access time is controlled by tAA. 16) Either tRCH or tRRH must be satisfied for a read cycle. 17) tOFF (max.) and tOEZ (max.) define the time at which the outputs achieve the open-circuit condition and are not referenced to output voltage levels. 18) Either tDZC or tDZO must be satisfied. 19) Either tCDD or tODD must be satisfied. 20) tWCS, tRWD, tCWD, tAWD and tCPWD are not restrictive operating parameters. They are included in the data sheet as electrical characteristics only. If tWCS > tWCS (min.), the cycle is an early write cycle and the I/O pin will remain open-circuit (high impedance) through the entire cycle; if tRWD > tRWD (min.), tCWD > tCWD (min.), tAWD > tAWD (min.) and tCPWD > tCPWD (min.) , the cycle is a read-write cycle and I/O pins will contain data read from the selected cells. If neither of the above sets of conditions is satisfied, the condition of the I/O pins (at access time) is indeterminate. 21) These parameters are referenced to CAS leading edge in early write cycles and to WE leading edge in ReadModify-Write cycles. Semiconductor Group 10 HYM72V4000/10GS-50/-60 4M x 72-ECC Module L-DIM-168-5 Module package (dual read-out, single in-line memory module) 133,35 3,0 1 10 11 40 84 41 25,40 17,78 *) 127,35 B A 95 96 124 168 6,35 1,27 3,125 3,125 6,35 125 2,0 Detail A 1,0 +- 0.5 2,54 min. 85 2,0 0,2 + - 0,15 Detail C Detail B 4Mx72 3.3V DM168-5.WMF preliminary drawing *) 9 mm thickness for modules assembled with SOJ-devices 4mm thickness for modules assembled with TSOPII-devices Semiconductor Group 11