Section 8: Interfacing To DSPs

INTERFACING TO DSPS
SECTION 8
INTERFACING TO DSPs
■
Parallel Interfacing to DSP Processors: Reading Data
From Memory-Mapped Peripheral ADCs
■
Parallel Interfacing to DSP Processors: Writing Data to
Memory-Mapped DACs
■
Serial Interfacing to DSP Processors
■
Interfacing I/O Ports, Analog Front Ends, and Codecs
to DSPs
■
DSP System Interface
8.a
INTERFACING TO DSPS
8.b
INTERFACING TO DSPS
SECTION 8
INTERFACING TO DSPs
Walt Kester, Dan King
INTRODUCTION
As the technology in the rapidly growing field of mixed signal processing evolves,
more highly integrated DSP products are being introduced (such as the ADSP21ESP202) which contain on-chip ADCs and DACs as well as the DSP, thereby
eliminating most component-level interface problems. Stand-alone ADCs and DACs
are now available with interfaces especially designed for DSP chips, thereby
minimizing or eliminating external interface support or glue logic. High
performance sigma-delta ADCs and DACs are currently available in the same
package (called a CODEC or COder/DECcoder) such as the AD73311 and AD73322.
These products are also designed to require minimum glue logic when interfacing to
the most common DSP chips. This section discusses the various data transfer and
timing issues associated with the various interfaces.
PARALLEL INTERFACING TO DSP PROCESSORS:
READING DATA FROM MEMORY-MAPPED PERIPHERAL
ADCS
Interfacing an ADC or a DAC to a fast DSP parallel requires an understanding of
how the DSP processor reads data from a memory-mapped peripheral (the ADC)
and how the DSP processor writes data to a memory-mapped peripheral (the DAC).
We will first consider some general timing requirements for reading and writing
data. It should be noted that the same concepts presented here regarding ADCs and
DACs apply equally when reading and writing from/to external memory.
A block diagram of a typical parallel DSP interface to an external ADC is shown in
Figure 8.1. This diagram has been greatly simplified to show only those signals
associated with reading data from an external memory-mapped peripheral device.
The timing diagram for the ADSP-21xx read-cycle is shown in Figure 8.2.
In this example it is assumed that the ADC is sampling at a continuous rate which
is controlled by the external sampling clock, not the internal DSP clock. Using a
separate clock for the ADC is the preferred method, since the DSP clock may be
noisy and introduce jitter in the ADC sampling process, thereby increasing the noise
level.
Assertion of the sampling clock at the ADC convert start input initiates the
conversion process (step 1). The leading (or trailing) edge of this pulse causes the
internal ADC sample-and-hold to switch from the sampling mode to the hold mode
so that the conversion process can take place. When the conversion is complete, the
conversion complete output of the ADC is asserted (step 2). The read process thus
begins when this signal is applied to the processor interrupt request line ( IRQ ) of
the DSP. The processor then places the address of the peripheral initiating the
8.1
INTERFACING TO DSPS
interrupt request (the ADC) on the memory address bus (A0 - A13) (step 3). At the
same time, the processor asserts a memory select line ( DMS is shown here) (step 4).
The two internal address buses of the ADSP-21xx (program memory address bus
and data memory address bus) share a single external address bus, and the two
internal data buses (program memory data bus and data memory data bus) share a
single external data bus. The boot memory select ( BMS ), data memory select
( DMS ), program memory select ( PMS ) and input/output memory select ( IOMS )
signals indicate which memory space the external buses are being used for. These
signals are typically used to enable an external address decoder as shown in Figure
8.1. The output of the address decoder drives the chip select input of the peripheral
device (step 5).
The memory read ( RD ) is asserted tASR ns after the DMS line is asserted (step 6).
The sum of the address decode delay plus the peripheral chip select setup time
should be less than tASR in order to take full advantage of the RD low-time. The RD
line remains low for tRP ns. The memory read signal is used to enable the three-state
parallel data outputs of the peripheral device (step 7). The RD line is connected to
the appropriate pin on the peripheral device usually called output enable or read.
The rising edge of the RD signal is used to clock the data on the data bus into the
DSP processor (step 8). After the rising edge of the RD signal, the data on the data
bus must remain valid for tRDH ns, the data hold time. In the case of most members
of the ADSP-21xx family, this specification value is 0ns.
The key timing requirements for the peripheral device are shown in Figure 8.3.
Values are given for the ADSP-2189M DSP operating at 75MHz.
ADC TO ADSP-21xx-FAMILY PARALLEL INTERFACE
ADSP-21xx
3
SAMPLING
CLOCK
MEMORY A0- A13
ADDRESS BUS
DATA MEMORY
DMS
SELECT
PROCESSOR
INTERRUPT
REQUEST
4
ADC
CONVERT START
5
ADDRESS
DECODE
CHIP SELECT
2
CONVERSION
COMPLETE
IRQ
6
MEMORY READ
RD
MEMORY DATA
BUS
D
8
OUTPUT ENABLE
7
OUTPUT DATA
Figure 8.1
8.2
1
INTERFACING TO DSPS
ADSP-21xx FAMILY MEMORY READ TIMING
DSP
CLKOUT
A0- A13
DMS, PMS,
IOMS, CMS
RD
tASR
tCRD
tRP
tRDA
tRWR
D
tRDH
tAA
tRDD
Figure 8.2
PARALLEL PERIPHERAL DEVICE READ INTERFACE
KEY REQUIREMENTS
■ Peripheral Device Data Outputs Must Be Three-State Compatible
■ Address Decode Delay + Peripheral Chip Select Setup Time Must Be
Less Than Address and Memory Select Setup Time tASR (0.325ns min
for ADSP-2189M)
■ For Zero Wait-State Access, the Time from a Negative-Going Edge of
Read Signal (RD) to Output Data Valid Must be Less than tRDD (1.65ns
max for ADSP-2189M Operating at 75MHz) or Software Wait-States
Must be Added, or Processor Clock Frequency Reduced
■ Output Data from Peripheral must Remain Valid for tRDH from the
Rising Edge of Read Signal (RD) (0ns for ADSP-2189M)
■ Peripheral Device Must Accept Minimum Output Enable Pulse Width of
tRP (3.65ns for ADSP-2189M Operating at 75MHz) or Software WaitStates Must be Added, or Processor Clock Frequency Reduced
Figure 8.3
8.3
INTERFACING TO DSPS
The DSP tRDD specification determines the peripheral device data access time
requirement. In the case of the ADSP-2189M, tRDD = 1.65ns minimum at 75MHz. If
the access time of the peripheral is greater than this, wait states must be added or
the processor speed reduced. This is a relatively common situation when interfacing
external memory or ADCs to fast DSPs. The relationship between these timing
parameters for the ADSP-2189M is given by the equations shown in Figure 8.4.
Note that these specifications are dependent on the DSP clock frequency.
ADSP-2189M PARALLEL READ TIMING AT 75MHz
■ tCK = Processor Clock Period (13.3ns)
■ tASR = Address and Memory Select Setup Before Read Low
= 0.25tCK – 3ns Minimum
■ tRDD = Read Low to Data Valid = 0.5tCK – 5ns + # wait states
× tCK Maximum
■ tRDH = Data Hold from Read High = 0ns Minimum
■ tRP = Read Pulse Width = 0.5tCK – 3ns + # wait states × tCK
Minimum
Figure 8.4
The ADSP-2189M can easily be interfaced to slow peripheral devices using its
programmable wait state generation capability. Three registers control wait state
generation for boot, program, data and I/O memory spaces. You can specify 0 to 15
wait states for each parallel memory interface. Each wait state added increases the
allowable external data memory access time by an amount equal to the processor
clock period (13.3ns for the ADSP-2189M operating at 75MHz). In this example, the
data memory address, DMS , and RD lines are all held stable for an additional
amount of time equal to the duration of the wait states.
The AD7854/AD7854L is a 12 bit, 200/100kSPS ADC which operates in the parallel
mode. It operates on a single +3V to +5.5V supply and dissipates only 5.5mW (+3V
supply, AD7854L). An automatic power-down after conversion feature reduces this
to 650µW.
8.4
INTERFACING TO DSPS
A functional block diagram of the AD7854/AD7854L is shown in Figure 8.5. The
AD7854/AD7854L uses a successive approximation architecture which is based on a
charge redistribution (switched capacitor) DAC. A calibration mode removes offset
and gain errors. The key interface timing specifications for the AD7854/AD7854L
and the ADSP-2189M are compared in Figure 8.6. Specifications for the ADSP2189M are given for a clock frequency of 75MHz.
Examining the timing specifications shown in Figure 8.6 reveals that for the timing
between the devices to be compatible, 5 software wait-states must be programmed
into the ADSP-2189M. This increases tRDD to 68.15ns which is greater than the
data access time of the AD7854/AD7854L (t8 = 50ns max.). The read pulse, tRP, is
likewise increased to 70.15ns which meets the ADC’s read pulse width requirement
(t7 = 70ns min.). Unless the memory-mapped peripheral has an extremely short
access time, wait states are generally required, whether interfacing to ADCs, DACs,
or external memory.
AD7854/AD7854L, +3V SINGLE SUPPLY, 12-BIT,
200/100kSPS PARALLEL OUTPUT ADC
AVDD
AIN(+)
AGND
AD7854/AD7854L
T/H
DVDD
AIN(–)
2.5 V
REFERENCE
REFIN /
REFOUT
CREF1
DGND
COMP
BUF
CHARGE
REDISTRIBUTION
DAC
CLKIN
SAR + ADC
CONTROL
CONVST
BUSY
CREF2
CALIBRATION
MEMORY
AND CONTROLLER
PARALLEL INTERFACE/CONTROL REGISTER
DB11 - DB0
CS
RD
WR
HBEN
Figure 8.5
8.5
INTERFACING TO DSPS
ADSP-2189M AND AD7854/AD7854L PARALLEL READ
INTERFACE TIMING SPECIFICATION COMPARISON
ADSP-2189M Processor (75MHz)
AD7854/AD7854L ADC
tASR (Data Address, Memory
Select Setup Time Before RD Low)
= 0.325ns min
t5 (CS to RD Setup Time =
0ns min (Must Add Address
Decode Time to this Value)
tRP (RD Pulse Width) =
3.65ns + # wait states × 13.3ns min
= 70.15ns min
t7 (RD Pulse Width) = 70ns min
tRDD (RD Low to Data Valid) =
1.65ns + # wait states × 13.3ns min
= 68.15ns min
t8 (Data Access Time After RD) =
50ns max
tRDH (Data Hold from RD High) =
0ns min
t9 (Bus Relinquish Time After RD) =
5ns min / 40ns max
NOTES:
(1) Adding 5 wait-states to the ADSP-2189M increases tRP to 70.15ns
which is greater than t7 (70ns) and meets the t8 (50ns) requirement.
(2) t9 max (40ns) may cause bus contention if a write cycle immediately follows
the read cycle.
Figure 8.6
A simplified interface diagram for the two devices is shown in Figure 8.7. The
conversion complete signal from the AD7854/AD7854L corresponds to the BUSY
output pin. Notice that the configuration allows the DSP to write data to the
AD7854/AD7854L parallel interface control register. This is needed in order to set
various options in the AD7854/AD7854L and perform the calibration routines. In
normal operation, however, data is read from the AD7854/AD7854L as described
above. Writing to external parallel memory-mapped peripherals is discussed later in
this section.
Parallel interfaces between other DSP processors and external peripherals can be
designed in a similar manner by carefully examining the timing specifications for all
appropriate signals for each device. The data sheets for most ADCs contain
sufficient information in the application section to interface them to the DSPs.
8.6
INTERFACING TO DSPS
AD7854/AD7854L ADC PARALLEL INTERFACE
TO ADSP-2189M
SAMPLING
CLOCK
CONVST
ADSP-2189M
75MHz
AD7854/AD7854L
ADC
DMS
A0
CS
(LOW = READ DB11 - DB0)
HBEN
IRQ
BUSY
WR
WR
RD
RD
D23 - D8
Notes:
DATA
DB11 - DB0
5 Software Wait-States
HBEN and WR required for writing to ADC
Sampling clock may come from DSP
Figure 8.7
PARALLEL INTERFACING TO DSP PROCESSORS:
WRITING DATA TO MEMORY-MAPPED DACS
A simplified block diagram of a typical DSP interface to a parallel peripheral device
(such as a DAC is shown in Figure 8.8. The memory-write cycle timing diagram for
the ADSP-21xx-family is shown in Figure 8.9.
In most real-time applications, the DAC is operated continuously from a stable
sampling clock. Most DACs for these applications have double buffering: an input
latch to handle the asynchronous DSP interface, followed by a second latch (called
the DAC latch) which drives the DAC current switches. The DAC latch strobe is
derived from an external stable sampling clock. In addition to clocking the DAC
latch, the DAC latch strobe is also used to generate a processor interrupt to the DSP
which indicates that the DAC is ready for a new input data word.
8.7
INTERFACING TO DSPS
DAC TO ADSP-21xx-FAMILY PARALLEL INTERFACE
ADSP-21xx
SAMPLING
CLOCK
MEMORY A0- A13
ADDRESS BUS
3
DATA MEMORY
DMS
SELECT
PROCESSOR
INTERRUPT
REQUEST
MEMORY DATA
BUS
DAC LATCH
STROBE
5
ADDRESS
DECODE
CHIP SELECT
1
IRQ
7
4
MEMORY WRITE
DAC
1
2
INPUT LATCH
STROBE
WR
6
PARALLEL DATA
INPUT
D
Figure 8.8
ADSP-21xx FAMILY MEMORY WRITE TIMING
DSP
CLKOUT
A0- A13
DMS, PMS,
BMS, CMS
tWP
WR
tWRA
tAW
tWWR
tASW
tDH
tCWR
D
tWDE
Figure 8.9
8.8
tDW
tDDR
INTERFACING TO DSPS
The write process is thus initiated by the peripheral device asserting the DSP
interrupt request line indicating that the peripheral is ready to accept a new parallel
data word (step 1). The DSP then places the address of the peripheral device on the
address bus (step 2) and asserts a memory select line ( DMS is shown here) (step 3).
This causes the output of the address decoder to assert the chip select input to the
peripheral (step 5). The write ( WR ) output of the DSP is asserted tASW ns after the
negative-going edge of the DMS signal (step 4). The width of the WR pulse is tWP
ns. Data is placed on the data bus (D) and is valid tDW ns before the WR line goes
high (step 6). The positive-going transition of the WR line is used to clock the data
on the data bus (D) into the external parallel memory (step 7). The data on the data
bus remains valid for tDH ns after the positive-going edge of the WR signal.
The key timing requirements for writing to the peripheral device are shown in
Figure 8.10. The key specification is tWP , the write pulse width. All but the fastest
peripheral devices will require wait states to be added due to their longer data
access times. Figure 8.11 shows the key timing specifications for the ADSP-2189M.
Note that they are all related to the processor clock frequency.
PARALLEL PERIPHERAL DEVICES WRITE INTERFACE
KEY REQUIREMENTS
■ Address Decode Delay + Peripheral Chip Select Setup Time Must
Be Less Than Address and Memory Select Setup Time tASW
(0.325ns for ADSP-2189M Operating at 75MHz)
■ For Zero Wait-State Access, Input Data Setup Time Must be Less
Than tDW (2.65ns for ADSP-2189M Operating at 75MHz) or Software
Wait-States Must be Added, or Processor Clock Frequency
Reduced
■ Input Data Hold Time Must be Less Than tDH (2.325ns for ADSP2189M Operating at 75MHz)
■ Peripheral Device Must Accept Input Write Clock Pulse of Width
tWP (3.65ns min for ADSP-2189M Operating at 75MHz) or SoftwareWait States Must be Added, or Processor Clock Frequency
Reduced
Figure 8.10
8.9
INTERFACING TO DSPS
ADSP-2189M PARALLEL WRITE TIMING
■ tCK = Processor Clock Period (13.3ns)
■ tASW = Address and Memory Select Before WR Low
= 0.25tCK – 3ns Minimum
■ tDW = Data Setup Before WR High = 0.5tCK – 4ns + # Wait States × tCK
■ tDH = Data Hold After WR High = 0.25tCK – 1ns
■ tWP = WR Pulse Width = 0.5tCK – 3ns + # Wait States × tCK Minimum
Figure 8.11
The AD5340 is a 12 bit 100kSPS DAC which has a parallel data interface. It
operates on a single +2.5V to +5.5V supply and dissipates only 345µW (+3V supply).
A power-down mode further reduces the power to 0.24µW. The part incorporates an
on-chip output buffer which can drive the output to both supply rails. The AD5340
allows the choice of a buffered or unbuffered reference input. The device has a
power-on reset circuit that ensures that the DAC output powers on at 0V and
remains there until valid data is written to the part. A block diagram is shown in
Figure 8.12. The input is double buffered. The key interface timing specifications for
the two devices are compared in Figure 8.13. Specifications for the ADSP-2189M are
given for a clock frequency of 75MHz.
AD5340 12-BIT, 100kSPS PARALLEL INPUT DAC
VREF
POWER-ON
RESET
DB0
BUF
GAIN
CS
WR
INTERFACE LOGIC
DB11
INPUT
REGISTER
DAC
REGISTER
12-BIT
DAC
RESET
CLR
POWER-DOWN
LOGIC
LDAC
PD
Figure 8.12
8.10
VOUT
BUF
GND
INTERFACING TO DSPS
ADSP-2189M AND AD5340 PARALLEL WRITE INTERFACE
TIMING SPECIFICATIONS
ADSP-2189M PROCESSOR (75MHz)
AD5340 DAC
tASW (Address and Data Memory
Select Setup Before WR Low)
= 0.325ns min
t1 (CS to WR Setup Time)
= 0ns min
tWP (WR Pulse Width) =
3.65ns + # Wait States × 13.3ns min
= 30.25ns min
t3 (WR Pulse Width)
= 20ns min
tDW (Data Setup Before WR High) =
2.65ns + # Wait States × 13.3ns min
= 29.25ns min
t4 (Data Valid to WR Setup Time)
= 5ns min
tDH (Data Hold After WR High)
= 2.325ns min
t5 (Data Valid to WR Hold Time)
= 4.5ns min
NOTE: Adding 2 wait states to the ADSP-2189M increases tWP to 30.25ns
and tDW to 29.25ns which is greater than t3 (20ns) and t4 (5ns) respectively.
Figure 8.13
Examining the timing specifications shown in Figure 8.13 reveals that for the
timing between the devices to be compatible, two software wait states must be
programmed into the ADSP-2189M. This increases the width of WR to 30.25ns
which is greater than the minimum required AD5340 write pulse width (20ns). The
data setup time of 5ns for the AD5340 is also met by adding two wait states. A
simplified interface diagram for the two devices is shown in Figure 8.14.
Parallel interfaces with other DSP processors can be designed in a similar manner
by carefully examining the timing specifications for all appropriate signals for each
device.
8.11
INTERFACING TO DSPS
AD5340 DAC PARALLEL INTERFACE TO ADSP-2189M
SAMPLING
CLOCK
LDAC
AD5340
DAC
ADSP-2189M
75MHz
DMS
CS
IRQ
WR
WR
D
Notes:
DB0 - DB11
2 Software Wait-States
Sampling clock may come from DSP
Figure 8.14
SERIAL INTERFACING TO DSP PROCESSORS
DSP processors which have serial ports (such as the ADSP-21xx family) provide a
simple interface to peripheral ADCs and DACs. Use of the serial port eliminates the
need for using large parallel buses to connect the ADCs and DACs to the DSP. In
order to understand serial data transfer better, we will first examine the serial port
operation of the ADSP-21xx series.
A block diagram of one of the two serial ports of the ADSP-21xx is shown in Figure
8.15. The Transmit (TX) and Receive (RX) registers are identified by name in the
ADSP-21xx assembly language, and are not memory mapped.
8.12
INTERFACING TO DSPS
ADSP-21xx FAMILY SERIAL PORT BLOCK DIAGRAM
DMD BUS
16
16
16
TXn
TRANSMIT DATA
REGISTER
COMPANDING
HARDWARE
(µ-LAW or A-LAW)
RXn
RECEIVE DATA
REGISTER
16
16
TRANSMIT SHIFT
REGISTER
SERIAL
CONTROL
RECEIVE SHIFT
REGISTER
INTERNAL
SERIAL
CLOCK
GEN.
DT
TFS SCLK
Polarity of TFS and RFS
is software programmable
RFS
DR
Figure 8.15
ADSP-21xx FAMILY SERIAL PORT FEATURES
■ Separate Transmit and Receive Sections for Each Port
■ Double-Buffered Transmit and Receive Registers
■ Serial Clock Can be Internally or Externally Generated
■ Transmit and Receive Frame Sync Signals Can be Internally or
Externally Generated
■ Serial Data Words of 3 to 16 Bits Supported
■ Automatically Generated Processor Interrupts
■ Hardware Companding Requires no Software Overhead
Figure 8.16
8.13
INTERFACING TO DSPS
In the receiving portion of the serial port, the receive frame sync (RFS) signal
initiates reception. The serial receive data (DR) from the external device (ADC) is
transferred into the receive shift register one bit at a time. The negative-going edge
of the serial clock (SCLK) is used to clock the serial data from the external device
into the receive shift register. When a complete word has been received, it is written
to the receive data register (RX), and the receive interrupt for that serial port is
generated. The receive data register is then read by the processor.
Writing to the transmit data register readies the serial port for transmission. The
transmit frame sync (TFS) signal initiates transmission. The value in the transmit
data register (TX) is then written to the internal transmit shift register. The data in
the transmit shift register is sent to the peripheral device (DAC) one bit at a time,
and the positive-going edge of the serial clock (SCLK) is used to clock the serial
transmit data (DT) into the external device. When the first bit has been transferred,
the serial port generates the transmit interrupt. The transmit data register can then
be written with new data, even though the transmission of the previous data is not
complete.
In the normal framing mode, the frame sync signal (RFS or TFS) is checked at the
falling edge of SCLK. If the framing signal is asserted, data is available (transmit
mode) or latched (receive mode) on the next falling edge of SCLK. The framing
signal is not checked again until the word has been transmitted or received. In the
alternate framing mode, the framing signal is asserted in the same SCLK cycle as
the first bit of a word. The data bits are latched on the falling edge of SCLK, but the
framing signal is checked only on the first bit. Internally-generated framing signals
remain asserted for the length of the serial word. The alternate framing mode of the
serial port in the ADSP-21xx is normally used to receive data from ADCs and
transmit data to DACs.
The serial ports of the ADSP-21xx family are extremely versatile. The TFS, RFS, or
SCLK signals can be generated from the ADSP-21xx clock (master mode) or
generated externally (slave mode). The polarity of these signals can be reversed
with software, thereby allowing more interface flexibility. The port also contains µlaw and A-law companding hardware for voiceband telecommunications
applications.
SERIAL ADC TO DSP INTERFACE
A timing diagram of the ADSP-2189M serial port operating in the receive mode
(alternate framing) is shown in Figure 8.17. The first negative-going edge of the
SCLK to occur after the negative-going edge of the RFS , clocks the MSB data from
the ADC into the serial input latch. The process continues until all serial bits have
been transferred into the serial input latch. The key timing specifications of concern
are the serial data setup (tSCS) and hold times (tSCH) with respect to the negativegoing edge of the SCLK. In the case of the ADSP-2189M, these values are 4ns and
7ns, respectively . The latest generation ADCs with high speed serial clocks will
have no trouble meeting these specifications, even at the maximum serial data
transfer rate.
8.14
INTERFACING TO DSPS
ADSP-2189M SERIAL PORT RECEIVE TIMING
ADC
SCLK
RFS IN
tSCS
≥ 4ns
DR IN
tSCS
tSCH
≥ 7ns
MSB
BIT n
LSB
ALTERNATE FRAMING MODE, ADC IS MASTER
Figure 8.17
The AD7853/AD7853L is a 12 bit, 200/100kSPS ADC which operates on a single
+3V to +5.5V supply and dissipates only 4.5mW (+3V supply, AD7853L). After each
conversion, the device automatically powers down to 25µW. The AD7853/AD7853L
is based on a successive approximation architecture and uses a charge
redistribution (switched capacitor) DAC. A calibration feature removes gain and
offset errors. A block diagram of the device is shown in Figure 8.18.
The AD7853 operates on a 4MHz maximum external clock frequency. The AD7853L
operates on a 1.8MHz maximum external clock frequency. The timing diagram for
AD7853L is shown in Figure 8.19. The AD7853/AD7853L has modes which
configure the SYNC and SCLK as inputs or outputs. In the example shown here
they are generated by the AD7853L. The AD7853L serial clock operates at a
maximum frequency of 1.8MHz (556ns period). The data bits are valid 330ns after
the positive-going edges of SCLK. This allows a setup time of approximately 330ns
minimum before the negative-going edges of SCLK, easily meeting the ADSP2189M 4ns tSCS requirement. The hold-time after the negative-going edge of SCLK
is approximately 226ns, again easily meeting the ADSP-2189M 7ns tSCH timing
requirement. These simple calculations show that the data and RFS setup and hold
requirements of the ADSP-2189M are met with considerable margin.
8.15
INTERFACING TO DSPS
AD7853/AD7853L +3V SINGLE-SUPPLY 12-BIT
200/100kSPS SERIAL OUTPUT ADC
AVDD
AIN(+)
AGND AGND
DVDD
AD7853L
T/H
AIN(–)
2.5 V
REFERENCE
REFIN /
REFOUT
DGND
COMP
BUF
CHARGE
REDISTRIBUTION
DAC
CREF1
CLKIN
CONVST
SAR + ADC
CONTROL
CREF2
BUSY
CALIBRATION
MEMORY
AND CONTROLLER
CAL
SLEEP
SERIAL INTERFACE/CONTROL REGISTER
SM1
SM2
SYNC
DIN
DOUT
SCLK
POLARITY
Figure 8.18
AD7853L SERIAL ADC OUTPUT TIMING
+3V SUPPLY, SCLK = 1.8MHz
SYNC (O/P)
SCLK
(O/P)
1
5
6
16
330ns min
THREE-STATE
DB15
DOUT (O/P)
226ns
DB11
556ns
Figure 8.19
8.16
DB0
THREE-STATE
INTERFACING TO DSPS
Figure 8.20 shows the AD7853L interfaced to the ADSP-2189M connected in a mode
to transmit data from the ADC to the DSP (alternate/master mode). The
AD7853/AD7853L contains internal registers which can be accessed by writing from
the DSP to the ADC via the serial port. These registers are used to set various
modes in the AD7853/AD7853L as well as to initiate the calibration routines. These
connections are not shown in the diagram.
AD7853/AD7853L SERIAL ADC
INTERFACE TO ADSP-2189M
ADSP-2189M
75MHz
DSP
CLOCK
INPUT
4MHz / 1.8MHz max
CLKIN
SAMPLING
CLOCK
(OPTIONAL)
CONVST
SCLK
SCLK
RFS
SYNC
DR
DOUT
AD7853/
AD7853L
ADC
SERIAL
PORT
Figure 8.20
SERIAL DAC TO DSP INTERFACE
Interfacing serial input DACs to the serial ports of DSPs such as the ADSP-21xx
family is also relatively straightforward and similar to the previous discussion
regarding serial output ADCs. The details will not be repeated here, but a simple
interface example will be shown.
The AD5322 is a 12-bit, 100kSPS dual DAC with a serial input interface. It operates
on a single +2.5V to +5.5V supply, and a block diagram is shown in Figure 8.21.
Power dissipation on a +3V supply is 690µW. A power-down feature reduces this to
0.15µW. Total harmonic distortion is greater than 70dB below full scale for a 10kHz
output. The references for the two DACs are derived from two reference pins (one
per DAC). The reference inputs may be configured as buffered or unbuffered inputs.
The outputs of both DACs may be updated simultaneously using the asynchronous
LDAC input. The device contains a power-on reset circuit that ensures that the
DAC outputs power up to 0V and remain there until a valid write takes place to the
device.
8.17
INTERFACING TO DSPS
AD5322 12-BIT, 100kSPS DUAL DAC
VREFA
VDD
POWERON
RESET
AD5322
INPUT
REGISTER A
DAC
REGISTER A
STRING
DAC A
VOUTA
SCLK
INTERFACE LOGIC
SYNC
DIN
RESISTOR
NETWORK
POWER-DOWN
LOGIC
INPUT
REGISTER B
DAC
REGISTER B
STRING
DAC B
VOUTB
RESISTOR
NETWORK
LDAC
GND
VREFB
Figure 8.21
Data is normally input to the AD5322 via the SCLK, DIN, and SYNC pins from the
serial port of the DSP. When the SYNC signal goes low, the input shift register is
enabled. Data is transferred into the AD5322 on the falling edges of the following 16
clocks. A typical interface between the ADSP-2189M and the AD5322 is shown in
Figure 8.22. Notice that the clocks to the AD5322 are generated from the ADSP2189M clock. It is also possible to generate the SCLK and SYNC signals externally
to the AD5322 and use them to drive the ADSP-2189M. The serial interface of the
AD5322 is not fast enough to handle the ADSP-2189M maximum master clock
frequency. However, the serial interface clocks are programmable and can be set to
generate the proper timing for fast or slow DACs.
The input shift register in the AD5322 is 16-bits wide. The 16-bit word consists of
four control bits followed by 12 bits of DAC data. The first bit loaded determines
whether the data is for DAC A or DAC B. The second bit determines if the reference
input will be buffered or unbuffered. The next two bits control the operating modes
of the DAC (normal, power-down with 1kΩ to ground, power-down with 100kΩ to
ground, or power-down with a high impedance output).
8.18
INTERFACING TO DSPS
AD5322 DAC SERIAL INTERFACE TO ADSP-2189M
ADSP-2189M
75MHz
AD5322
DAC
SCLK
SCLK
TFS
SYNC
DIN
DT
SERIAL
PORT
Figure 8.22
INTERFACING I/O PORTS, ANALOG FRONT ENDS,
AND CODECS TO DSPS
Since most DSP applications require both an ADC and a DAC, I/O Ports and
CODECs have been developed which integrate the two functions on a single chip as
well as provide easy-to-use interfaces to standard DSPs. These devices also go by
the name of analog front ends.
A functional block diagram of the AD73322 is shown in Figure 8.23. This device is a
dual analog front end (AFE) with two 16-bit ADCs and two 16-bit DACs capable of
sampling at 64KSPS. It is designed for general purpose applications including
speech and telephony using sigma-delta ADCs and sigma-delta DACs. Each channel
provides 77dB signal-to-noise ratio over a voiceband signal bandwidth.
The ADC and DAC channels feature programmable input/output gains with ranges
of 38dB and 21dB, respectively. An on-chip voltage reference is included to allow
single supply operation on +2.7V to +5.5V. Power dissipation is 73mW with a +3V
supply.
8.19
INTERFACING TO DSPS
AD73322 SINGLE SUPPLY 16-BIT, 64kSPS
CODEC WITH SERIAL INTERFACE
AVDD1
VFBP1
VINP1
VINN1
VFBN1
VOUTP1
VOUTN1
SDI
Σ∆ DAC
CHANNEL 1
SCLK
REFERENCE
VFBP2
VINP2
VINN2
VFBN2
Σ∆ ADC
CHANNEL 2
VOUTN2
DVDD
Σ∆ ADC
CHANNEL 1
REFOUT
REFCAP
VOUTP2
AVDD2
SDIFS
SE
SERIAL
PORT
MCLK
SDOFS
Σ∆ DAC
CHANNEL 2
AGND1
RESET
SDO
AGND2
DGND
Figure 8.23
The sampling rate of the CODECs is programmable with four separate settings of
64kHz, 32kHz, 16kHz, and 8kHz when operating from a master clock of
16.384MHz. The serial port allows easy interfacing of single or cascaded devices to
industry standard DSP engines, such as the ADSP-21xx family. The SPORT
transfer rate is programmable to allow interfacing to both fast and slow DSP
engines. The interface to the ADSP-218x family is shown in Figure 8.24. The SE pin
(SPORT enable) may be controlled from a parallel output pin or a flag pin such as
FL1, or where SPORT power down is not required, it can be permanently strapped
high using a suitable pull-up resistor. The RESET pin may be connected to the
system hardware reset, or it may be controlled with another flag bit.
In the program mode, data is transferred from the DSP to the AD73322 control
registers to set up the device for desired operation. Once the device has been
configured by programming the correct settings to the various control registers, the
device may exit the program mode and enter the data mode. The dual ADC data is
transmitted to the DSP in two blocks of 16-bit words. Similarly, the dual DAC data
is transmitted from the DSP to the AD73322 in two blocks of 16-bit words.
Simplified interface timing is also shown in Figure 8.24.
8.20
INTERFACING TO DSPS
AD73322 INTERFACE TO ADSP-218x SERIES
(DATA TRANSFER MODE)
TFS
SDIFS
DT
SDI
ADSP-218x
DSP
SCLK
SCLK
DR
AD73322
CODEC
CLOCK
16.384MHz
SDO
RFS
SDOFS
FL0
RESET
FL1
SE
SE
SCLK
SDOFS
SDO
ADC SAMPLE WORD, DEVICE 2 ADC SAMPLE WORD, DEVICE 1
SDIFS
SDI
DAC DATA WORD, DEVICE 2
DAC DATA WORD, DEVICE 1
Figure 8.24
The AD73422 is the first product in the dspConverter™ family of products which
integrate a dual analog front end (AD73322) and a DSP (52MIPS ADSP-2185L/86L).
The entire functionality of the dual-channel CODEC and the DSP fits into a small,
119-ball 14mm by 22mm plastic ball grid array (PBGA) package. The obvious
advantage is the saving of circuit board real estate. ADC and DAC signal-to-noise
ratios are approximately 77dB over voiceband frequencies.
The AD74222-80 integrates 80K bytes of on-chip memory configured as 16K words
(24-bit) of program RAM, and 16K words (16-bit) of data RAM. The AD73422-40
integrates 40K bytes of on-chip memory configured as 8K words (24-bit) of program
RAM, and 8K words (16-bit) of data RAM. Power-down circuitry is also provided to
meet the low power needs of battery operated portable equipment. The AD73422
operates on a +3V supply and dissipates approximately 120mW with all functions
operational.
8.21
INTERFACING TO DSPS
AD73422 dspConverter™
■
■
■
■
■
Complete Dual CODEC (AD73322) and DSP (ADSP-2185L/86L)
14mm by 22mm BGA package
+3V Single-Supply Operation, 73mW Power Dissipation
Power-Down Mode
CODEC:
◆ Dual 16-bit Sigma-Delta ADCs and DACs
◆ Data Rates: 8, 16, 32, and 64KSPS
◆ 77dB SNR
■ DSP:
◆ 52MIPS
◆ ADSP-218x Code Compatible
◆ 80K Byte and 40K Byte On-Chip Memory Options
Figure 8.25
HIGH-SPEED INTERFACING
With the advent of ever faster DSP clock rates and newer architectures it has
become possible to acquire and process high speed signals. The programmability of
DSPs makes it possible to run different algorithms on the same hardware, while
providing different system functionality. Figure 8.26 shows a simplified ADSP21065L system connected to a high-speed ADC and high-speed DAC. The ADC and
DAC both have parallel interfaces connected to the External Port of the DSP. With
the SHARC family of DSPs there are several ways of connecting the converters to
this port. The access to the converters can be done using the direct memory access
(DMA) controller of the DSP or it can be done under program control using the core
of the DSP. Using the DMA places no load on the DSP core so it can continue
processing (executing program instructions) while the data is transferred to from
the on-chip memory.
The AD9201 is a dual-channel, 10-bit, 20MSPS ADC which operates on a single
+2.7V to +5.5V supply and dissipates only 215mW (+3V supply). The AD9201 offers
closely matched ADCs needed for many applications such as I/Q communications.
Input buffers, an internal voltage reference and multiplexed digital outputs buffers
make interfacing to the AD9201 very simple.
The companion part to the AD9201 ADC is the AD9761 DAC. The AD9761 is a dual
10-bit, 20MSPS per channel DAC operating on a single +2.7V to +5.5V supply and
dissipating only 200mW (+3V supply). A voltage reference, digital latches and 2x
interpolation make the AD9761 useful for I/Q transmitter applications.
8.22
INTERFACING TO DSPS
AD9201 ADC AND AD9761 DAC
INTERFACE TO ADSP-21065L
ADSP21065L
A0
D0 - D9
RD
WR
TCLK
DUAL 10-BIT
20MSPS ADCs
AD9201
ADC
AD9761
DAC
D0 - D9
D0 - D9
CLOCK
CLOCK
SELECT
SELECT
CHIP-SELECT
DUAL 10-BIT
20MSPS DACs
WRITE
Figure 8.26
DSP SYSTEM INTERFACE
Figure 8.26 shows a simplified ADSP-2189M system using the full memory mode
configuration with two serial devices, a byte-wide EPROM, and optional external
program and data overlay memories. Programmable wait state generation allows
the fast processor to connect easily to slower peripheral devices. The ADSP-2189M
also provides four external interrupts, seven general-purpose input/output pins and
two serial ports. One of the serial ports can be configured as two additional
interrupts, a general-purpose input and a general-purpose output pin for a total of
six external interrupts, 9 IOs and one serial port. The ADSP-2189M can also be
operated in the host memory mode which allows access to the full external data bus,
but limits addressing to a single address bit. Additional system peripherals can be
added in the host memory mode through the use of external hardware to generate
and latch address signals.
8.23
INTERFACING TO DSPS
ADSP-2189M SYSTEM INTERFACE:
FULL MEMORY MODE
ADSP-2189M
CLKIN
1/2 X CLOCK
OR
CRYSTAL
INTERRUPTS
GENERAL
PURPOSE IO
XTAL
4
7
14
14
ADDR
8
24
MODE x
5
SPORT1
DATA
11
WR
16
IOMS
SPORT0
PMS
ADDR
DATA
I/O SPACE
(PERIPHERALS)
2048 LOCATIONS
OVERLAY
MEMORY
TWO 8K PM SEGMENTS
TWO 8K DM SEGMENTS
DMS
CMS
BR
BG
BGH
PWD
PWDACK
BUS REQUEST/
GRANT/HUNG
POWER DOWN INPUT
POWER DOWN OUTPUT
Figure 8.27
8.24
DATA
CS
24
SERIAL
DEVICE
ADDR
14
5
BYTE
MEMORY
CS
BMS
RD
SERIAL
DEVICE
ADDR
8
DATA
IRQ x
22
INTERFACING TO DSPS
REFERENCES
1.
Steven W. Smith, The Scientist and Engineer’s Guide to Digital Signal
Processing, Second Edition, 1999, California Technical Publishing,
P.O. Box 502407, San Diego, CA 92150. Also available for free download at:
http://www.dspguide.com or http://www.analog.com
2.
C. Britton Rorabaugh, DSP Primer, McGraw-Hill, 1999.
3.
Richard J. Higgins, Digital Signal Processing in VLSI, Prentice-Hall,
1990.
4.
DSP Designer’s Reference (DSP Solutions) CDROM, Analog Devices,
1999.
5.
DSP Navigators: Interactive Tutorials about Analog Devices’ DSP
Architectures (Available for ADSP-218x family and SHARC family):
http://www.analog.com/industry/dsp/training/index.html#Navigator
6.
General DSP Training and Workshops:
http://www.analog.com/industry/dsp/training
The following DSP Reference Manuals and documentation are available
for free download from: http://www.analog.com/industry/dsp/tech_docs.html
7.
ADSP-2100 Family Users Manual, 3rd Edition, Sept., 1995.
8.
ADSP-2100 Family EZ Tools Manual.
9.
ADSP-2100 EZ-KIT Lite Reference Manual.
10.
Using the ADSP-2100 Family, Vol. 1, Vol. 2.
11.
ADSP-2106x SHARC User’s Manual, 2nd Edition, July, 1996.
12.
ADSP-2106x SHARC EZ-KIT Lite Manual.
13.
ADSP-21065L SHARC User’s Manual, Sept. 1, 1998.
14.
ADSP-21065L SHARC EZ-LAB User’s Manual.
15.
ADSP-21160 SHARC DSP Hardware Reference.
8.25
INTERFACING TO DSPS
8.26