TPS25944XEVM

User's Guide
SLUUBC2A – May 2015 – Revised July 2015
TPS25944X635EVM: Evaluation Module for TPS25944X
This user’s guide describes the evaluation module (EVM) for the Texas instruments TPS25944X devices.
TPS25944X devices are circuit breaker with True Reverse Blocking for Power Mux that operates from 2.7
V to 18 V, device has integrated back-to-back FETs with programmable undervoltage, overvoltage,
reverse-voltage, overcurrent and in-rush current protection features.
Important Note to TPS25944XEVM-635 Users
While ordering the TPS25944XEVM-635, customers may receive the EVM with TPS25940XEVM-635 or
TPS25942XEVM-635 labels.
Make the following changes to configure the received EVM as TPS25944XEVM-635, to achieve the
TPS25944X circuit breaker functionality:
1. Please order TPS25944ARVCR and TPS25944LRVCR samples from www.ti.com
2. Replace the U1, as the with TPS25944A
3. Replace the U2, as the with TPS25944L
4. Make sure the following parts are unpopulated:
• R7, R8
1
2
3
4
5
6
Contents
Introduction ................................................................................................................... 2
1.1
EVM Features ....................................................................................................... 2
1.2
EVM Applications ................................................................................................... 2
Description .................................................................................................................... 3
Schematic .................................................................................................................... 4
General Configurations ..................................................................................................... 5
4.1
Physical Access ..................................................................................................... 5
4.2
Test Equipment ..................................................................................................... 6
4.3
Test Setup ........................................................................................................... 7
4.4
Test Procedures .................................................................................................... 8
EVM Assembly Drawings and Layout Guidelines ...................................................................... 13
5.1
PCB Drawings ..................................................................................................... 13
Bill of Materials (BOM) ..................................................................................................... 15
List of Figures
1
2
3
4
5
6
7
8
9
10
11
............................................................................................... 4
EVM Test Setup.............................................................................................................. 7
Vout Ramp-Up Time of Auto-Retry Circuit Breaker (CH1) ............................................................. 9
Vout Ramp-up Time of Latched Circuit Breaker (CH2) ............................................................... 10
Output Short Circuit Behavior of Auto-Retry Circuit Breaker (CH1) ................................................. 11
Circuit Breaking Time Delay (CH1) ...................................................................................... 11
Output Short-Circuit Behavior of Latched Circuit Breaker (CH2) .................................................... 12
Circuit-Breaking Time Delay (CH2) ...................................................................................... 12
Top Side Placement ....................................................................................................... 13
Top Side Routing Layer ................................................................................................... 13
Bottom Side Routing Layer ............................................................................................... 14
TPS25944XEVM Schematic
SLUUBC2A – May 2015 – Revised July 2015
Submit Documentation Feedback
TPS25944X635EVM: Evaluation Module for TPS25944X
Copyright © 2015, Texas Instruments Incorporated
1
Introduction
www.ti.com
List of Tables
1
1
TPS25944X EVM Options and Default Setting .......................................................................... 3
2
Input and Output Connector Functionality ................................................................................ 5
3
Test Points Description
4
Jumper and LEDs Descriptions ............................................................................................ 5
5
Operational Range Setting for VIN1, VIN2 = 12 V, 5 V and 3.3 V .................................................... 8
6
PWR635 DMM Readings at Different Test Points....................................................................... 8
7
PWR635 Oscilloscope Setting for Ramp-Up Voltage Test ............................................................. 9
8
PWR635 Oscilloscope Setting for Current Limit Test
10
9
PWR635 Jumper Setting for Current Limits
10
10
TPS25944XEVM-635 Bill of Material
15
.....................................................................................................
.................................................................
............................................................................
...................................................................................
5
Introduction
The TPS25944X-EVM allows reference circuit evaluation of TI's TPS25944X devices. The TPS25944X
devices are available with both latched and auto-retry operation.
1.1
EVM Features
•
•
•
•
1.2
EVM Applications
•
•
•
•
•
2
General TPS25944XEVM features are:
– 2.7-V to 18.0-V (TYP) operation
• CH1 rising input voltage turn-On threshold – 10.8 V (TYP)
• CH1 falling input voltage turn-off threshold – 10 V (TYP)
• CH2 rising input voltage turn-On threshold – 10.8 V (TYP)
• CH2 falling input voltage turn-off threshold – 2.1 V (TYP)
– 0.6 A to 5.0 A programmable current limit
– Programmable undervoltage lockout/overvoltage
– Programmable VOUT slew rate
– Latched-off TPS25944LRUV (CH2)
– Auto-retry TPS25944ARUV (CH2)
Push button RESET signal
On-board transorb is for overvoltage input protection
Common diode at output prevents negative spike when load is removed
Solid state drives and hard disk drives
PCIe, RAID, and NIC Cards
USB power switch
Industrial:
– PLCs
– Solid state relays and FAN control
Power Path Management:
– Active ORing
– Priority power multiplexing
TPS25944X635EVM: Evaluation Module for TPS25944X
Copyright © 2015, Texas Instruments Incorporated
SLUUBC2A – May 2015 – Revised July 2015
Submit Documentation Feedback
Description
www.ti.com
2
Description
The TPS25944XEVM-635 enables full evaluation of the TPS25944X devices. The EVM supports two
versions (Auto-Retry and Latched) of the devices on two Channels (CH1 and CH2, respectively). Input
power is applied at J3 (CH1) and J8 (CH2), while J2 (CH1)/J7 (CH2) provide the output connection to the
load, refer to the schematic in Figure 1, and test setup in Figure 2.
D5/C1 (CH1), D9/C7 (CH2) provides input protection for TPS25944X (U1 and U2, respectively) while
D4/C2/C3/C4 (CH1), D8/C8/C9/C10 (CH2) provides output protection.
S1 allows U1 and S2 allows U2 to be RESET or disabled. A power good (PG) indicator is provided by D2
and D6 for CH1 and CH2, respectively, and circuit faults can be observed with D2 and D6. Scaled channel
current can be monitored at TP11 and T22 with a scale factor of 0.842 V/A.
Table 1. TPS25944X EVM Options and Default Setting
UVLO
Part Number
TPS25944XEVM-635
EVM Function
Circuit Breaker
SLUUBC2A – May 2015 – Revised July 2015
Submit Documentation Feedback
Current Limit
Vin Range
2.7 V–18 V
OVP
CH1
CH2
10.8 V
Internal
(2.3 V)
16.5 V
Fault Response
LO
Setting
No Jumper
HI Setting
CH1
CH2
3.6 A
2.1 A
5.3 A
Auto-retry
Latched
TPS25944X635EVM: Evaluation Module for TPS25944X
Copyright © 2015, Texas Instruments Incorporated
3
Schematic
3
www.ti.com
Schematic
Figure 1 illustrates the TPS25944X EVM schematic.
PG-1
1
TP1
SYS_PG
VIN1
3
D1
BAT54C-7-F
TP2
VOUT1
SH-J1
1
2
3
2
PG-2
TP3
VIN1
VOUT1
J1
VOUT1
9
10
11
12
13
TP5
OVP1
TP8
EN_UV1
EN/UVLO-1
IN
IN
IN
IN
IN
14
OVP-1
15
DVDT-118
4
5
6
7
8
OUT
OUT
OUT
OUT
OUT
EN/UVLO
C1
0.1µF
OVP
DEVSLP
DVDT
PGOOD
PGTH
D5
J3
2
1
C5
330pF
R2
100k
P-LOAD
TP6
R4
475k
D2
FLTb-1
Red
TP9
PG1
R5
10.0k
P-LOAD
DNP D3
Green
Q1
CSD17301Q5A
30V
TP7
I-LOAD
R6
0.1
Pin1_CTRL-1
TP10
1
2
3
P-LOAD-RTN
PGTH-1
D4
B320A-13-F
20V
ILIM-1
17
OVP-2
R8
324k
16
GND
PAD
IMON
R9
2
IIN=0.6A-5.0A
19
16V
PG-1
4
20
FLTB
ILIM
VIN=2.7V-18V
R1
TP4
100k FLTb1
U1
1,2,3
R3
475k
5,6,
7,8
VIN1
C2
4.7µF
C3
4.7µF
J2
C4
330µF
1
2
VOUT1
VOUT=2.7V-18V
IOUT=0.6A-5.0A
VOUT2
R7
0.003
TPS25944ARVC
IMON-1
16.9k
TP11
IMON
IMON-1
R11
47k
3
2
1
J4
DNPC6
1nf
R13
32.4k
R10
16.9k
ILIM LO
1
S1
PG-1
FLTb-1
R12
24.9k
ILIM HI
SH-J4
TP12
R14
16.2k
TP13
Pin1_CTRL-2
1
3
Net-Tie
2
4
TP14
J5
Net-Tie
DNP
Net-Tie
SH-J5
SGND1
TP15
VIN2
TP16
VOUT2
VIN2
TP17
EN_UV2
EN/UVLO-2 14
15
C7
1µF
DVDT-2
OVP-2
18
J8
2
1
R17
100k
U2
9
10
11
12
13
IN
IN
IN
IN
IN
OUT
OUT
OUT
OUT
OUT
EN/UVLO
FLTB
OVP
DEVSLP
DVDT
PGOOD
PGTH
D9
ILIM
R22
C11 DNP
48.7k
330pF
2
16V
19
GND
PAD
IMON
4
5
6
7
8
FLTb-2
PG-2
Pin1_CTRL-1
TP20
FLTb2
TP21
PG2
Red
D7
Green
J6
R20
475k
DNP
Q2
20
TP19
1
R21
10k
Pin1_CTRL-2
1
J7
2
3
D8
B320A-13-F
20V
PGTH-2
ILIM-2
17
C8
4.7µF
C9
4.7µF
1
2
C10
330µF
VOUT=2.7V-18V
IOUT=0.6A-5.0A
VIN2
R23
47k
16
SH-J10
R24
100k DNP
TPS25944LRVC
ILIM LO
TP22
IMON2
DNPC12
1nf
TP24
3
2
1
J9
ILIM HI
SH-J9
R28
16.2k
R25
16.9k
R27
24.9k
Pin1_CTRL-2
Net-Tie
1
2
3
J10
3
1
IMON-2
R26
35.7k
TP25
TP26
Net-Tie
DNP
Q3
2
S2
1
2
3
D6
3
R19
475k
TP18
OVP2
IIN=0.6A-5.0A
SH-J6
R15
100k DNP
R16
100k
2
R18
475k
VIN=2.7V-18V
VIN1
VOUT2
1
TP23
R29
10k
Net-Tie
SGND2
Figure 1. TPS25944XEVM Schematic
4
TPS25944X635EVM: Evaluation Module for TPS25944X
SLUUBC2A – May 2015 – Revised July 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
General Configurations
www.ti.com
4
General Configurations
4.1
Physical Access
Table 2 lists the TPS25944XEVM-635 input and output connector functionality, Table 3 describes the test
point availability, and Table 4 describes the jumper functionality.
Table 2. Input and Output Connector Functionality
Connector
J3
CH1
J2
J8
CH2
J7
Label
Description
VIN1(+), GND(–)
CH1 Input power supply to the EVM
VOUT1(+),GND(–)
CH1 Output power from the EVM
VIN2(+), GND(–)
CH2 Input power supply to the EVM
VOUT2(+),GND–)
CH2 Output power from the EVM
Table 3. Test Points Description
Channel
CH1
CH2
Test Points
Label
Description
TP3
VIN1
CH1 Input power supply to the EVM
TP8
EN_UV1
CH1 Active high enable and undervoltage input
TP5
OVP1
CH1 Active high overvoltage input (> 16.5 V)
TP11
IMON1
CH1 Current monitor. Load current = 1.187 × voltage on TP11
TP2
VOUT1
CH1 Output from the EVM
TP9
PG1
CH1 Power good test point
TP4
FLTb1
TP12
GND
GND
TP13
GND
GND
TP14
GND
GND
TP15
VIN2
CH2 Input power supply to the EVM
TP17
EN_UV2
CH1 Fault test point
CH2 Active high enable and under voltage input
TP18
OVP2
CH2 Active high overvoltage input
TP22
IMON2
CH2 Current monitor. Load current = 1.187 × voltage on TP22
TP16
VOUT2
CH2 Output from the EVM
TP21
PG2
CH2 Power good test point
TP20
FLTb2
TP24
GND
GND
TP25
GND
GND
TP26
GND
GND
CH2 Fault test point
Table 4. Jumper and LEDs Descriptions
Jumper
Label
Description
J4
LO - HI
J5
J5
J9
LO - HI
D2 (Red)
D2
CH1 circuit fault indicator. LED turns on when the internal MOSFET is disabled due to a fault
condition such as over load , short circuit, under voltage etc.
D3 (Green)
D3
CH1 Power good indicator. LED turns on when the voltage at TP2(VOUT1) is more than 10.8V
D6 (Red)
D6
CH2 circuit fault indicator. LED turns on when the internal MOSFET is disabled due to a fault
condition such as over load , short circuit, under voltage etc.
D7 (Green)
D7
CH2 Power good indicator. LED turns on when the voltage at TP2(VOUT1) is more than 10.8V
CH2 Current Setting
PG1 and FLTb1 setting
CH2 Current Setting
SLUUBC2A – May 2015 – Revised July 2015
Submit Documentation Feedback
TPS25944X635EVM: Evaluation Module for TPS25944X
Copyright © 2015, Texas Instruments Incorporated
5
General Configurations
4.2
4.2.1
www.ti.com
Test Equipment
Power Supplies
One adjustable power supply: 0-V to 20-V output, 0-A to 6-A output current limit.
4.2.2
Meters
One DMM minimum needed and may require more if simultaneous measurements are needed.
4.2.3
Oscilloscope
A DPO2024 or Lecroy 424 oscilloscope or equivalent, three 10X voltage probes, and a DC current probe.
4.2.4
Loads
One resistive load or equivalent which take up to 6 ADC load at 12 V and capable to do the output short.
6
TPS25944X635EVM: Evaluation Module for TPS25944X
Copyright © 2015, Texas Instruments Incorporated
SLUUBC2A – May 2015 – Revised July 2015
Submit Documentation Feedback
General Configurations
www.ti.com
4.3
Test Setup
Figure 2 shows a typical test setup for the TPS25944XEVM. Connect J3/J8 to the power supply and J2/J7
to the load.
xx
xxxx
xxxx
Oscilloscope
x
x
x
x
CIN
NOITAZILITU %
BAT
F I ER DG
7M
DG DG DG
8N
AHPLA
3U
2 T DG
TFIHS
Z Y XW
.
Load
J2
Positive
U1
Positive
Voltmeter
CIN
D2
R7
D3
S1
+
DUT
PWR635
-
UAM/BUH
NOITAZILITU %
BAT
F I ER DG
C L BK
AJ
TNIRP
9O
7M
PLEH
DG DG DG
RETNE
NUR
8N
AHPLA
3U
TFIHS
Z Y XW
.
2 T DG
CNB
s/bM4
0V
Voltmeter
Negative
J8
D9
Positive
Negative
Positive
D6
Texas
Instruments
D7
S2
Load
J7
U2
Power
Supply
CNB
s/bM4
0V
TP
13
J3
AJ
9O
PLEH
Negative
D5
Negative
C L BK
TNIRP
RETNE
NUR
TP
12
Power
Supply
UAM/BUH
TP
24
TP
25
Figure 2. EVM Test Setup
SLUUBC2A – May 2015 – Revised July 2015
Submit Documentation Feedback
TPS25944X635EVM: Evaluation Module for TPS25944X
Copyright © 2015, Texas Instruments Incorporated
7
General Configurations
4.4
www.ti.com
Test Procedures
Use the following procedures for testing:
1. The operational voltage range of the two rails VIN1 and VIN2 can be adjusted by changing a few
resistor settings, as listed in Table 5.
Table 5. Operational Range Setting for VIN1, VIN2 = 12 V, 5 V and 3.3 V
VIN Operational Range
Rail: VIN1 or VIN2
R9
R13
R11
R22
R8
12 V: 10.5 V to 16 V
(Default)
VIN1
16.9 kΩ
32.4 kΩ
47 kΩ
5 V: 4.6 V to 5.7 V
VIN1
23.2 kΩ
105 kΩ
137 kΩ
3.3 V: 3 V to 3.8 V
VIN1
48.7 kΩ
187 kΩ
237 kΩ
2.3 V to 15.5 V (Default)
5 V: 4.6 V to 5.7 V
VIN2
No PoP
32.4 kΩ
VIN2
130 kΩ
3.3 V: 3 V to 3.8 V
100 kΩ
VIN2
237 kΩ
169 kΩ
2. Turn on the power supply and set the power supply voltage to 12 V on CH1 and CH2.
3. Turn off the power supply. Hook up CH1 and CH2 of the PWR635 assembly as shown in Figure 3.
4. Ensure that the output load is disabled and the power supply is set properly for the DUT. Connect the
negative probe of DMM to TP12 or TP25 (GND) to the test points in Table 6.
5. Turn on the power supply. Verify that the voltages shown in Table 6 are obtained. Use only one power
supply at a time for this verification.
Table 6. PWR635 DMM Readings at Different Test Points
4.4.1
Voltage Test on
(CH1)
Measured Voltage
Reading
Voltage Tested
on (CH2)
Measured Voltage
Reading
VIN1 (TP3)
12 ±0.3 VDC
VIN2 (TP15)
12 ±0.3 VDC
EN_UV1 (TP8)
1.13 ±0.1 VDC
EN_UV2 (TP17)
12 ±0.3 VDC
OVP1 (TP5)
0.742 ±0.1 VDC
OVP2 (TP18)
0.742 ±0.1 VDC
IMON1 (TP11)
33.8 mV ±5 mVDC
IMON2 (TP22)
33.8 mV ±5 mVDC
VOUT1 (TP2)
12 ±0.3 VDC
VOUT2 (TP16)
12 ±0.3 VDC
PG1 (TP9)
2.40 ±0.1 VDC
PG2 (TP21)
2.4 ±0.1 VDC
FLTb1 (TP4)
10.51 ±0.5 VDC
FLTb2 (TP20)
10.5 ±0.5 VDC
Preliminary Test
Use the steps in the following sections for preliminary testing.
4.4.1.1
For CH1 (J3-J2)
1. With the power supply set to 12 V on CH1, verify that the red LED (D2) is off. Press the EVM RST
switch (S1) and verify that the voltage at VOUT1 (TP2) starts falling slowly below 12 V and that the
FLTb1 red LED (D2) turns ON. Release S1.
2. Reduce the input voltage on VIN1 and monitor VOUT1. Verify that VOUT1 (TP2) starts falling and is
fully turned off when VIN1 (TP3) reaches 9.5 V (±0.5 V). Verify that the FLTb1 red LED (D2) turns ON.
3. Increase the input voltage on VIN1 and monitor VOUT1. Verify that VOUT1(TP2) starts increasing and
is fully turned off when VIN1 (TP3) reaches 16.5 V (±1 V). Verify that the FLTb1 red LED (D2) turns
ON.
4.4.1.2
For CH2 (J8-J7)
1. With the power supply set to 12 V on VIN2, press the EVM RST switch (S2) and verify that the voltage
at VOUT2 (TP16) starts falling slowly below 12 V and that the green PG LED (D7) turns off and the
RED FLTb2 LED (D6) turns on. Release S2.
2. Reduce the input voltage on VIN2 and monitor VOUT2. Verify that VOUT2 (TP16) starts falling and is
8
TPS25944X635EVM: Evaluation Module for TPS25944X
Copyright © 2015, Texas Instruments Incorporated
SLUUBC2A – May 2015 – Revised July 2015
Submit Documentation Feedback
General Configurations
www.ti.com
fully turned off when VIN2 (TP15) reaches 2.1 V (+0.3 V). Verify that the PG2 green LED (D7) turns off
and the FLTb2 red LED (D6) turns ON.
3. Increase the input voltage on VIN2 and monitor VOUT2. Verify that VOUT2 (TP16) starts increasing
and is fully turned off when VIN2 (TP15) reaches 15.5 V (±1 V). Verify that the PG2 green LED (D7)
turns off and the FLTb2 red LED (D6) turns ON.
4. Turn off the power supply.
4.4.1.3
Ramp-Up Time Test (CH1 and CH2)
1. Verify ramp-up time (CH1 and CH2, with only 1 channel powered at a time). Set up the oscilloscope as
shown in Table 7.
Table 7. PWR635 Oscilloscope Setting for Ramp-Up Voltage Test
Oscilloscope Setting
CH1 Probe Points
CH2 Probe Points
Channel 1 = 5 V/div
TP2 = VOUT1
TP16 = VOUT2
Channel 2 = 5 V/div
TP3 = VIN1
TP15 = VIN2
Channel 3 = 5 V/div
TP8 = EN/UVLO1
TP17 = EN/UVLO2
Channel 4 = 2 A/div
Current probe in input +Ve wire
Current probe in input +Ve wire
Trigger source = Channel 1
Trigger level = 6.0 ±0.5 V
Trigger polarity = Positive
Trigger Mode = Single Sequence
Time base = 1 ms/div
2. Set the output load at 5 Ω on CH1 and then enable the load. Turn on the power supply, Press the EVM
RST switch (S1) and release, verify that VOUT1 (TP2) ramps up as shown in Figure 3.
Figure 3. Vout Ramp-Up Time of Auto-Retry Circuit Breaker (CH1)
3. Set the output load at 5 Ω on CH2 and then enable the load. Turn on the power supply, Press the EVM
RST switch (S2) and release, verify that VOUT2 (TP16) ramps up as shown in Figure 4.
SLUUBC2A – May 2015 – Revised July 2015
Submit Documentation Feedback
TPS25944X635EVM: Evaluation Module for TPS25944X
Copyright © 2015, Texas Instruments Incorporated
9
General Configurations
www.ti.com
Figure 4. Vout Ramp-up Time of Latched Circuit Breaker (CH2)
4.4.1.4
Circuit Breaker Current Limit Test
1. Verify all three current limits (CH1 and CH2, with only 1 channel powered at a time) and verify the
Latch and auto-retry feature. Setup the oscilloscope as shown in Table 8.
Table 8. PWR635 Oscilloscope Setting for Current Limit Test (1)
Oscilloscope Setting
CH1 Probe Points
CH2 Probe Points
Channel 1 = 5 V/div
TP2 = VOUT1
TP16 = VOUT2
Channel 2 = 5 V/div
TP3 = VIN1
TP15 = VIN2
Channel 4 = 5 A/div
Input current into J3 +Ve wire
Input current into J8 +Ve wire
Trigger source = Channel 4
Trigger level = 1.0 ±0.2 A
Trigger polarity = +Ve
Trigger Mode = Single Sequence
Time base
(1)
40 ms/div
If an electronic load is used, ensure that the output load is set to constant resistance mode and not constant current mode.
2. The jumper setting for the different current limit test is shown in Table 9.
Table 9. PWR635 Jumper Setting for Current Limits
Jumper Position
J4 (CH1)
10
J9 (CH2)
Load Current Limit
HI
HI
5.3 A
LO
LO
3.6 A
No Jumper
No Jumper
2.1 A
TPS25944X635EVM: Evaluation Module for TPS25944X
Copyright © 2015, Texas Instruments Incorporated
SLUUBC2A – May 2015 – Revised July 2015
Submit Documentation Feedback
General Configurations
www.ti.com
3. Set the output load at 1.0 ±0.1 Ω on CH1 and current limit to 5.3 A, and then enable the load. Turn on
the power supply, verify that input current is limited as per the setting in Table 9 and the device goes in
auto retry mode and FLTb1, RED LED (D2) turns ON. Observe from Figure 7 that the circuit breaking
time delay is 4.36 ms
Figure 5. Output Short Circuit Behavior of Auto-Retry Circuit Breaker (CH1)
Figure 6. Circuit Breaking Time Delay (CH1)
4. Set the output load at 1.0 ±0.1 Ω on CH1 and current limit to 5.3 A and then enable the load. Turn on
the VIN2 power supply and verify that the input current is limited as per the setting in Table 9 and the
device is in latched-off mode and FLTb2 RED LED (D6) turns ON.
SLUUBC2A – May 2015 – Revised July 2015
Submit Documentation Feedback
TPS25944X635EVM: Evaluation Module for TPS25944X
Copyright © 2015, Texas Instruments Incorporated
11
General Configurations
www.ti.com
Figure 7. Output Short-Circuit Behavior of Latched Circuit Breaker (CH2)
Figure 8. Circuit-Breaking Time Delay (CH2)
5. Set the input power supply to zero volts and disconnect all equipment from the DUT
12
TPS25944X635EVM: Evaluation Module for TPS25944X
Copyright © 2015, Texas Instruments Incorporated
SLUUBC2A – May 2015 – Revised July 2015
Submit Documentation Feedback
EVM Assembly Drawings and Layout Guidelines
www.ti.com
5
EVM Assembly Drawings and Layout Guidelines
5.1
PCB Drawings
Figure 9 through Figure 11 show component placement and layout of the EVM.
Figure 9. Top Side Placement
Figure 10. Top Side Routing Layer
SLUUBC2A – May 2015 – Revised July 2015
Submit Documentation Feedback
TPS25944X635EVM: Evaluation Module for TPS25944X
Copyright © 2015, Texas Instruments Incorporated
13
EVM Assembly Drawings and Layout Guidelines
www.ti.com
Figure 11. Bottom Side Routing Layer
14
TPS25944X635EVM: Evaluation Module for TPS25944X
Copyright © 2015, Texas Instruments Incorporated
SLUUBC2A – May 2015 – Revised July 2015
Submit Documentation Feedback
Bill of Materials (BOM)
www.ti.com
6
Bill of Materials (BOM)
Table 10. TPS25944XEVM-635 Bill of Material (1)
Designator
QTY
Part Number
Manufacturer
Alternate Part
Number
Alternate
Manufacturer
!PCB
1
C1
1
0.1uF
CAP, CERM, 0.1uF, 25V, +/-10%, X7R, 0603
0603
PWR635
Any
-
-
06033C104KAT2A
AVX
C2, C3, C8, C9
4
4.7uF
CAP, CERM, 4.7uF, 25V, +/-10%, X7R, 1206
C4, C10
2
330uF
CAP, AL, 330uF, 25V, +/-20%, 0.16 ohm, SMD
1206
C3216X7R1E475K
TDK
HA0
EMZA250ADA331MHA0G
C5, C11
2
330pF
Nippon Chemi-Con
CAP, CERM, 330pF, 100V, +/-5%, X7R, 0603
0603
06031C331JAT2A
C7
1
AVX
1uF
CAP, CERM, 1uF, 25V, +/-10%, X5R, 0603
0603
C1608X5R1E105K080AC
D1
TDK
1
30V
Diode, Schottky, 30V, 0.2A, SOT-23
SOT-23
BAT54C-7-F
Diodes Inc.
D2, D6
2
Red
LED, Red, SMD
Power TOPLED w/lens
LS E63F-DBFA-1-Z
OSRAM
-
-
D4, D8
2
20V
Diode, Schottky, 20V, 3A, SMA
SMA
B320A-13-F
Diodes Inc.
D5, D9
2
16V
Diode, TVS, Uni, 16V, 600W, SMB
SMB
SMBJ16A-13-F
Diodes Inc.
D7
1
Green
LED, Green, SMD
Power TOPLED w/lens
LT E63C-CADB-35-L-Z
OSRAM
-
-
FID1, FID2,
FID3
0
Fiducial mark. There is nothing to buy or mount.
Fiducial
N/A
N/A
H1, H2, H3, H4
4
Bumpon, Cylindrical, 0.312 X 0.200, Black
Black Bumpon
SJ61A1
3M
J1, J4, J6, J9,
J10
5
Header, TH, 100mil, 1x3, Gold plated, 230 mil above insulator
PBC03SAAN
PBC03SAAN
Sullins Connector
Solutions
Equivalent
Any
J2, J3, J7, J8
4
Terminal Block, 2x1, 5.08mm, TH
10.16x15.2x9mm
282841-2
TE Connectivity
J5
1
Header, TH, 100mil, 2x2, Gold plated, 230 mil above insulator
TSW-102-07-G-D
TSW-102-07-G-D
Samtech Inc
Equivalent
Any
LBL1
1
Thermal Transfer Printable Labels, 0.650" W x 0.200" H - 10,000 per
roll
PCB Label 0.650"H x
0.200"W
THT-14-423-10
Brady
-
-
Q1
1
30V
MOSFET, N-CH, 30V, 100A, SON 5x6mm
SON 5x6mm
CSD17301Q5A
Texas Instruments
None
None
R1, R2, R16,
R17
4
100k
RES, 100k ohm, 5%, 0.1W, 0603
0603
CRCW0603100KJNEA
Vishay-Dale
R3, R4, R18,
R19, R20
5
475k
RES, 475k ohm, 1%, 0.1W, 0603
0603
CRCW0603475KFKEA
Vishay-Dale
Equivalent
Any
R5
1
10.0k
RES, 10.0k ohm, 1%, 0.1W, 0603
0603
CRCW060310K0FKEA
Vishay-Dale
Equivalent
Any
R6
1
0.1
RES, 0.1 ohm, 1%, 3W, 2512
2512
CRA2512-FZ-R100ELF
Bourns
R9, R10, R25
3
16.9k
RES, 16.9k ohm, 1%, 0.1W, 0603
0603
CRCW060316K9FKEA
Vishay-Dale
[NoValue], [NoValue],
Equivalent
[NoValue], [NoValue],
Any
R11, R23
2
47k
RES, 47k ohm, 5%, 0.1W, 0603
0603
CRCW060347K0JNEA
Vishay-Dale
R12, R27
2
24.9k
RES, 24.9k ohm, 1%, 0.1W, 0603
0603
CRCW060324K9FKEA
Vishay-Dale
R13
1
32.4k
RES, 32.4k ohm, 1%, 0.1W, 0603
0603
CRCW060332K4FKEA
Vishay-Dale
R14, R28
2
16.2k
RES, 16.2k ohm, 1%, 0.1W, 0603
0603
CRCW060316K2FKEA
Vishay-Dale
R15, R24
2
100k
RES, 100k ohm, 1%, 0.1W, 0603
0603
CRCW0603100KFKEA
Vishay-Dale
R21, R29
2
10k
RES, 10k ohm, 5%, 0.1W, 0603
0603
CRCW060310K0JNEA
Vishay-Dale
R26
1
35.7k
RES, 35.7k ohm, 1%, 0.1W, 0603
0603
RC0603FR-0735K7L
Yageo America
S1, S2
2
Switch, Push Button, SMD
2.9x2x3.9mm SMD
SKRKAEE010
Alps
Equivalent
Any
SH-J1, SH-J4,
SH-J9
3
Shunt, 100mil, Gold plated, Black
Shunt
969102-0000-DA
3M
SNT-100-BK-G
Samtec
(1)
Value
Description
Package Reference
Printed Circuit Board
1x3
1x2
Unless otherwise noted in the Alternate Part Number and/or Alternate Manufacturer columns, all parts may be substituted with equivalents.
SLUUBC2A – May 2015 – Revised July 2015
Submit Documentation Feedback
TPS25944X635EVM: Evaluation Module for TPS25944X
Copyright © 2015, Texas Instruments Incorporated
15
Bill of Materials (BOM)
www.ti.com
Table 10. TPS25944XEVM-635 Bill of Material (1) (continued)
Designator
QTY
Value
Description
Package Reference
Part Number
Manufacturer
Alternate Part
Number
Alternate
Manufacturer
TP1, TP4, TP5,
TP8, TP9,
TP11, TP17,
TP18, TP20,
TP21, TP22
11
White
Test Point, TH, Multipurpose, White
Keystone5012
5012
Keystone
Equivalent
Any
TP2, TP3,
TP15, TP16
4
Red
Test Point, TH, Multipurpose, Red
Keystone5010
5010
Keystone
Equivalent
Any
TP6, TP19,
TP23
3
Orange
Test Point, Multipurpose, Orange, TH
Orange Multipurpose
Testpoint
5013
Keystone
TP7
1
White
Test Point, Multipurpose, White, TH
White Multipurpose
Testpoint
5012
Keystone
TP10, TP14,
TP26
3
Black
Test Point, TH, Multipurpose, Black
Keystone5011
5011
Keystone
Equivalent
Any
TP12, TP13,
TP24, TP25
4
SMT
Test Point, SMT, Compact
Testpoint_Keystone_Com
pact
5016
Keystone
Equivalent
Any
U1
1
2.7V-18V eFuse with True Reverse Blocking for Power Mux,
RVC0020A
RVC0020A
TPS25944ARVC
Texas Instruments
None
U2
1
2.7V-18V eFuse with True Reverse Blocking for Power Mux,
RVC0020A
RVC0020A
TPS25944LRVC
Texas Instruments
None
C6, C12
0
1000pF
CAP, CERM, 1000pF, 100V, +/-20%, X7R, 0603
0603
06031C102MAT2A
AVX
-
-
D3
0
Green
LED, Green, SMD
Power TOPLED w/lens
LT E63C-CADB-35-L-Z
OSRAM
-
-
Q2, Q3
0
60V
MOSFET, N-CH, 60V, 0.31A, SOT-323
SOT-323
2N7002KW
Fairchild
Semiconductor
R22
0
48.7k
RES, 48.7k ohm, 1%, 0.1W, 0603
0603
CRCW060348K7FKEA
Vishay-Dale
SH-J5, SH-J6,
SH-J10
0
1x2
Shunt, 100mil, Gold plated, Black
Shunt
969102-0000-DA
3M
16
TPS25944X635EVM: Evaluation Module for TPS25944X
None
SNT-100-BK-G
Samtec
SLUUBC2A – May 2015 – Revised July 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Revision History
www.ti.com
Revision History
Changes from Original (May 2015) to A Revision ........................................................................................................... Page
•
Added Important Note to TPS25944XEVM-635 Users. .............................................................................. 1
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
SLUUBC2A – May 2015 – Revised July 2015
Submit Documentation Feedback
Revision History
Copyright © 2015, Texas Instruments Incorporated
17
STANDARD TERMS AND CONDITIONS FOR EVALUATION MODULES
1.
Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, or
documentation (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms and conditions set forth herein.
Acceptance of the EVM is expressly subject to the following terms and conditions.
1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility
evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not
finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For
clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions
set forth herein but rather shall be subject to the applicable terms and conditions that accompany such Software
1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,
or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production
system.
2
Limited Warranty and Related Remedies/Disclaimers:
2.1 These terms and conditions do not apply to Software. The warranty, if any, for Software is covered in the applicable Software
License Agreement.
2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM
to User. Notwithstanding the foregoing, TI shall not be liable for any defects that are caused by neglect, misuse or mistreatment
by an entity other than TI, including improper installation or testing, or for any EVMs that have been altered or modified in any
way by an entity other than TI. Moreover, TI shall not be liable for any defects that result from User's design, specifications or
instructions for such EVMs. Testing and other quality control techniques are used to the extent TI deems necessary or as
mandated by government requirements. TI does not test all parameters of each EVM.
2.3 If any EVM fails to conform to the warranty set forth above, TI's sole liability shall be at its option to repair or replace such EVM,
or credit User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the
warranty period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to
repair or replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall
be warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day
warranty period.
3
Regulatory Notices:
3.1 United States
3.1.1
Notice applicable to EVMs not FCC-Approved:
This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with the kit
to determine whether to incorporate such items in a finished product and software developers to write software applications for
use with the end product. This kit is not a finished product and when assembled may not be resold or otherwise marketed unless
all required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product not cause
harmful interference to licensed radio stations and that this product accept harmful interference. Unless the assembled kit is
designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must operate under the authority of
an FCC license holder or must secure an experimental authorization under part 5 of this chapter.
3.1.2
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:
CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
FCC Interference Statement for Class A EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
FCC Interference Statement for Class B EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3.2 Canada
3.2.1
For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210
Concerning EVMs Including Radio Transmitters:
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Concernant les EVMs avec appareils radio:
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concerning EVMs Including Detachable Antennas:
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types
listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited
for use with this device.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le
présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le
manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur
3.3 Japan
3.3.1
Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に
輸入される評価用キット、ボードについては、次のところをご覧ください。
http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page
3.3.2
Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified
by TI as conforming to Technical Regulations of Radio Law of Japan.
If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required by Radio Law of
Japan to follow the instructions below with respect to EVMs:
1.
2.
3.
Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for
Enforcement of Radio Law of Japan,
Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to
EVMs, or
Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan
with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note
that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.
SPACER
SPACER
SPACER
SPACER
SPACER
【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて
いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの
措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用
いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ
ンスツルメンツ株式会社
東京都新宿区西新宿6丁目24番1号
西新宿三井ビル
3.3.3
Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧くださ
い。http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
SPACER
4
EVM Use Restrictions and Warnings:
4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT
LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.
4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling
or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information
related to, for example, temperatures and voltages.
4.3 Safety-Related Warnings and Restrictions:
4.3.1
User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user
guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and
customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input
and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or
property damage. If there are questions concerning performance ratings and specifications, User should contact a TI
field representative prior to connecting interface electronics including input power and intended loads. Any loads applied
outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible
permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any
load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative.
During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit
components may have elevated case temperatures. These components include but are not limited to linear regulators,
switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the
information in the associated documentation. When working with the EVM, please be aware that the EVM may become
very warm.
4.3.2
EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the
dangers and application risks associated with handling electrical mechanical components, systems, and subsystems.
User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees,
affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic
and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely
limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and
liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or
designees.
4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal,
state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all
responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and
liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local
requirements.
5.
Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate
as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as
accurate, complete, reliable, current, or error-free.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
6.
Disclaimers:
6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY WRITTEN DESIGN MATERIALS PROVIDED WITH THE EVM (AND THE
DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL FAULTS." TI DISCLAIMS ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY
THIRD PARTY PATENTS, COPYRIGHTS, TRADE SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS.
6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS AND
CONDITIONS SHALL BE CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY
OTHER INDUSTRIAL OR INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD
PARTY, TO USE THE EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY
INVENTION, DISCOVERY OR IMPROVEMENT MADE, CONCEIVED OR ACQUIRED PRIOR TO OR AFTER DELIVERY OF
THE EVM.
7.
USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS
LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES,
EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY
HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS AND CONDITIONS. THIS OBLIGATION
SHALL APPLY WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY
OTHER LEGAL THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED.
8.
Limitations on Damages and Liability:
8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE,
INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE
TERMS ANDCONDITIONS OR THE USE OF THE EVMS PROVIDED HEREUNDER, REGARDLESS OF WHETHER TI HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED
TO, COST OF REMOVAL OR REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES, RETESTING, OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS,
LOSS OF SAVINGS, LOSS OF USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL
BE BROUGHT AGAINST TI MORE THAN ONE YEAR AFTER THE RELATED CAUSE OF ACTION HAS OCCURRED.
8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY WARRANTY OR OTHER OBLIGATION
ARISING OUT OF OR IN CONNECTION WITH THESE TERMS AND CONDITIONS, OR ANY USE OF ANY TI EVM
PROVIDED HEREUNDER, EXCEED THE TOTAL AMOUNT PAID TO TI FOR THE PARTICULAR UNITS SOLD UNDER
THESE TERMS AND CONDITIONS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE CLAIMED. THE EXISTENCE
OF MORE THAN ONE CLAIM AGAINST THE PARTICULAR UNITS SOLD TO USER UNDER THESE TERMS AND
CONDITIONS SHALL NOT ENLARGE OR EXTEND THIS LIMIT.
9.
Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s)
will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in
a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable
order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s),
excluding any postage or packaging costs.
10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas,
without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to
these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas.
Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief
in any United States or foreign court.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
spacer
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated