Freescale Semiconductor, Inc.
User’s Guide
Document Number: KT34FS6407-34FS6408UG
Rev. 1.0, 8/2015
KIT34FS6407EVB and KIT34FS6408EVB
Evaluation Board
Figure 1. KIT34FS6407EVB and KIT34FS6408EVB Board
© Freescale Semiconductor, Inc., 2015. All rights reserved.
Contents
1
Important Notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
2
Getting Started. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
3
Terms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
4
Getting to Know the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
5
Accessory Interface Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
6
Installing the Software and Setting up the Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
7
Initialization and Configuration Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
8
Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
9
Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
10 References. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
11 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
2
Freescale Semiconductor, Inc.
Important Notice
1
Important Notice
Freescale provides the enclosed product(s) under the following conditions:
This evaluation kit is intended for use of ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES
ONLY. It is provided as a sample IC pre-soldered to a printed circuit board to make it easier to access inputs,
outputs, and supply terminals. This evaluation kit may be used with any development system or other source
of I/O signals by simply connecting it to the host MCU or computer board via off-the-shelf cables. Final device
in an application will be heavily dependent on proper printed circuit board layout and heat sinking design as
well as attention to supply filtering, transient suppression, and I/O signal quality.
The goods provided may not be complete in terms of required design, marketing, and or manufacturing related
protective considerations, including product safety measures typically found in the end product incorporating
the goods. Due to the open construction of the product, it is the user's responsibility to take any and all
appropriate precautions with regard to electrostatic discharge. In order to minimize risks associated with the
customers applications, adequate design and operating safeguards must be provided by the customer to
minimize inherent or procedural hazards. For any safety concerns, contact Freescale sales and technical
support services.
Should this evaluation kit not meet the specifications indicated in the kit, it may be returned within 30 days from
the date of delivery and will be replaced by a new kit.
Freescale reserves the right to make changes without further notice to any products herein. Freescale makes
no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor
does Freescale assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages.
“Typical” parameters can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typical”, must be validated for each customer application by customer’s
technical experts.
Freescale does not convey any license under its patent rights nor the rights of others. Freescale products are
not designed, intended, or authorized for use as components in systems intended for surgical implant into the
body, or other applications intended to support or sustain life, or for any other application in which the failure
of the Freescale product could create a situation where personal injury or death may occur.
Should the Buyer purchase or use Freescale products for any such unintended or unauthorized application,
the Buyer shall indemnify and hold Freescale and its officers, employees, subsidiaries, affiliates, and
distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising
out of, directly or indirectly, any claim of personal injury or death associated with such unintended or
unauthorized use, even if such claim alleges that Freescale was negligent regarding the design or manufacture
of the part. Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other
product or service names are the property of their respective owners. © Freescale Semiconductor, Inc. 2015
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
Freescale Semiconductor, Inc.
3
Getting Started
2
Getting Started
2.1
Kit Contents/Packing List
The KIT34FS6407EVB and KIT34FS6408EVB contents include:
• Assembled and tested evaluation board/module in anti-static bag
• Warranty card
2.2
Jump Start
Freescale’s analog product development boards help to easily evaluate Freescale products. These tools support analog mixed signal and
power solutions including monolithic ICs using proven high-volume SMARTMOS mixed signal technology, and system-in-package devices
utilizing power, SMARTMOS and MCU dies. Freescale products enable longer battery life, smaller form factor, component count reduction,
ease of design, lower system cost and improved performance in powering state of the art systems.
• Click on the appropriate link for your board
KIT34FS6407EVB:
www.freescale.com/KIT34FS6407EVB
KIT34FS6408EVB: www.freescale.com/KIT34FS6408EVB
• Review your Tool Summary Page
• Look for
Jump Start Your Design
• Download documents, software, and other information
Once the files are downloaded, review the user guide in the bundle. Jump start bundles are available on each tool summary page with the
most relevant and current information. The information includes everything needed for design.
2.3
Required Equipment and Software
To use this kit, you need
• 2.7 V to 40 V power supply, 3.0 A capability
• Freescale’s KITUSBSPIDGLVME interface dongle
• SPIGen Graphical User Interface or MC3390X_GUI
When not connected to an evaluation board, the KITUSBSPIDGLVME can be used in standalone mode to program its
onboard MC68HC908JW32 microcontroller. In this case, the interface dongle and USB cable are required. For more
information, see the “SPIGen 7 User Guide”.
2.4
System Requirements
The kit requires the following:
• USB-enabled PC with Windows® XP or higher
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
4
Freescale Semiconductor, Inc.
Terms
3
Terms
Part Number or
Parameter
CAN_5V
EVB
Definition
5.0 V CAN voltage
Evaluation Board
FCCU
Fault Collection and Control Unit
FS0B
Fail-safe Output Number 0
INTB
Interrupt
IO
LDO
Input/Output
Low-dropout Regulator
RSTB
Reset
SMPS
Switching Mode Power Supply
SPIGen
Software utility (installed on a PC) provides communication functions between the PC and a Freescale evaluation board
VAUX
Auxiliary power supply
VCCA
Power supply for ADC
VPRE
Pre-regulator voltage
WD
Watchdog
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
Freescale Semiconductor, Inc.
5
Getting to Know the Hardware
4
Getting to Know the Hardware
4.1
Board Overview
KIT34FS6407EVB and KIT34FS6408EVB evaluation boards demonstrate the functionality of the SMARTMOS MC34FS6407 and
MC34FS6408 power system basis chips, respectively. These ICs are equipped with an intelligent power management system including
safety features targeting the latest ISO26262 automotive functional safety standard. The EVB is a standalone board that can be used
either with a compatible microcontroller or with a PC. The latter case requires a KITUSBSPIDGLEVME accessory interface board. See
Section 2.3 "Required Equipment and Software".
4.2
Board Features
This EVB comes mounted with either an MC34FS6407 or an MC34FS6408 IC. The main features of the board are:
• VBAT power supply either through power jack (2.0 mm) or phoenix connector
• VCORE configuration:1.2 V or 3.3 V
• VCCA configuration: 5.0 V/3.3 V
• Internal transistor or external PNP
• VAUX configuration: 3.3 V or 5.0 V
• Enabled or disabled at startup
• Ignition key switch
• CAN bus
• IO connector (IO_0 to IO_5)
• Debug connector (SPI bus, CAN digital, RSTB, FS0B, INTB, Debug, MUX_OUT)
• Signalling LED to give state of signals or regulators
4.3
Device Features
The MC34FS6407 and the MC34FS6408 are multi-output ICs, with power supply and HSCAN transceiver. The MC34FS6407 is designed
to support up 800 mA on VCORE, while MC34FS6408 supports up to 1.5 A on VCORE. All other features are the same.
Table 1. Device Features
Device
MC34FS6407/
MC34FS6408
Description
Power system
basis chip with
high-speed CAN
and LIN
transceivers
Features
• Highly flexible SMPS pre-regulator, allowing two topologies: non-inverting buck-boost or
standard buck
• Switching mode power supply (SMPS) dedicated to MCU core supply: 1.2 V or 3.3 V,
delivering up to 1.5 A for the MC34FS6408 and up to 800 mA for the MC34FS6407
• Linear voltage regulator dedicated to MCU A/D reference voltage or I/Os supply (VCCA):
5.0 V or 3.3 V
• Linear voltage regulator dedicated to auxiliary functions or to a sensor supply (VCCA
tracker or independent 5.0 V/3.3 V)
• Multiple wake-up sources in Low-power mode: CAN and/or IOs
• Battery voltage sensing and multiplexer output terminal (various signal monitoring)
• Enhanced safety block associated with fail-safe outputs
• Six configurable I/Os
• ISO11898 high-speed CAN interface compatibility for baud rates of 40 kB/s to 1.0 MB/s
• High EMC immunity and ESD robustness
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
6
Freescale Semiconductor, Inc.
Getting to Know the Hardware
4.4
Board Description
The EVB comes with either a Freescale MC34FS6407or MC34FS6408 IC mounted on it. Below is a view of the board indicating the major
components.
Buck/Buck Boost
Section
Power Supplies
LEDs for
Power
Supplies
Battery
Connection
Compensation
Network
Main
Switch
VCORE
Selection
Ignition
Key
Switch
DBG Mode
Select
LIN Bus
(Not Avaiable on
KIT34FS640xEVB)
SPI Dongle
Connector
CAN Bus
Second Resistor Bridge
- VDRIFG Selection
I/Os of
MC34FS6407/MC34FS6406
VCCA and VAUX
Selection
Main Signals of
MC34FS6407/MC34FS6406
FS Output
Circuitry
Figure 2. Board Description —MC34FS6407and MC34FS6408
Table 2. Board Description
Name
Buck/Buck-Boost Section
Battery Connection
Main Switch
Description
• VPRE DC/DC selection mode, either Boost or Buck
• Battery voltage input, either on Jack (black connector) or Phoenix (green) connector
• Battery voltage ON/OFF
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
Freescale Semiconductor, Inc.
7
Getting to Know the Hardware
Table 2. Board Description (continued)
Name
Description
• Simulate ignition key. Connected to IO_0
Ignition Key Switch
LIN Bus
• LIN bus as a master (Not available on KIT34FS640xEVB)
CAN Bus
• CANH and CANL differential pair
• All IOs, VDDIO and GND available
I/Os of MC34FS6407_8
Second Resistor Bridge - VDRIFT Selection
Main Signals of MC34FS6407_8
VCCA and VAUX Selection
FS Output Circuitry
SPI Dongle Connector
DBG Mode Select
VCORE Selection
Compensation Network
LEDs for Power Supplies
Power Supplies
4.5
• Bridge resistor for VCORE redundant check
• SPI, VDDIO, fail-safe pin, CAN, MUXOUT, INTB and RSTB available
• VCCA and VAUX voltage selection
• FS0B configuration
• Connector with SPI bus. Compliant to SPIGen Freescale board
• Controls Debug or Normal mode entering at boot up
• VCORE voltage selection
• Compensation network selection
• Switches for ON/OFF on LEDs
• MC34FS6407 or MC34FS6408 output power supply (VPRE, VCORE, VAUX, VCCA)
Evaluation Board Configuration
Figure 3 shows a configuration example for the EVB, which enables:
• VCORE 3.3 V
• Compensation network for MPC5643L
• VCCA and VAUX = 5.0 V
• VCCA with external PNP
• Debug mode
• VPRE in Buck mode
• VDDIO tied to VCCA
• Various signalling LEDs enabled
• IO1 configured as IN/OUT
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
8
Freescale Semiconductor, Inc.
Getting to Know the Hardware
KIT34FS640XEVB REV A
2015 FREESCALE
Switch
Jumper
Red LED
Green LED
Figure 3. Default Board Configuration
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
Freescale Semiconductor, Inc.
9
Getting to Know the Hardware
4.6
LED Definitions
The following table lists the LEDs used as visual output devices on the EVB:
Table 3. LEDs
Schematic
Label
Name
D6
VPRE
Indicator of pre-regulator voltage
D7
VAUX
Indicator of auxiliary power supply
D8
VCCA
Indicator of ADC power supply
D9
CAN_5V
Indicator of 5.0 V CAN voltage
D10
IO_5
Indicator of IO_5 state
D11
IO_4
Indicator of IO_4 state
D12
FS0B
Indicator for fail-safe output number 0
D13
VBAT_P
Indicator of battery voltage after protection diode
D14
RSTB
Indicator of a reset
D15
INTB
Indicator of an interrupt
D17
VCORE
4.7
Description
Indicator of VCORE power supply
Test Point Definitions
The following test-point jumpers provide access to signals on the MC34FS6407or MC34FS6408:
Table 4. Test Points
Schematic Label
Signal Name
Description
TP2
J24.3
-
TP3
J24.5
-
TP4
J24.7
-
TP5
J20.16
-
TP6
PGND
Power ground
TP7
PGND
Power ground
TP8
GND
Ground
TP9
GND
Ground
TP10
GND
Ground
TP11
GND
Ground
TP12
GND
Ground
TP13
GND
Ground
TP14
GND
Ground
TP15
GND
Ground
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
10
Freescale Semiconductor, Inc.
Getting to Know the Hardware
Table 4. Test Points (continued)
Schematic Label
Signal Name
Description
TP16
GND
Ground
TP17
GND
Ground
TP18
J24.2
-
TP19
J24.4
-
TP20
J24.6
-
TP21
J24.8
-
TP22
J24.10
-
TP23
J24.12
-
TP24
J24.14
-
TP25
J24.16
-
TP26
VPRE
TP27
VCORE
Core voltage for the MCU
TP28
CANH
-
TP29
CANL
-
TP30
LIN
TP31
MUX_OUT
TP32
FS0B
Fail-safe output
TP33
RSTB
Reset signal
TP34
INTB
Interrupt output
TP35
VSW
VPRE Switching voltage
TP36
VAUX
Auxiliary power supply
TP37
VCCA
ADC power supply
TP38
CAN_5V
CAN power supply
TP39
VSUP3
TP40
VSW_Core
Pre-regulator voltage
LIN bus (Not available on
KIT34FS640xEVB)
Output from the analog multiplexer
Supply voltage
VCORE supply voltage
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
Freescale Semiconductor, Inc.
11
Getting to Know the Hardware
4.8
Connector and Jumper Definitions
Table 5. Main Power Supply Connector
JP1 Pin Number
Name of Power Rail
Description
1
VCORE
Core voltage for the MCU
2
PGND
Power ground
3
VCCA
ADC power supply
4
GND
Ground
5
VAUX
Auxiliary power supply
6
GND
Ground
7
CAN_5V
8
GND
Ground
9
VPRE
Pre-regulator voltage
10
PGND
Power ground
CAN power supply
Table 6. Jumpers J1 through J31 (Including Connectors)
Schematic
Label
J1
J2
Pin Number
Pin Name
Jumper/Pin Function
Compensation network for FB_core – part 1
1-2
VCORE = 1.23 V
3-4
VCORE = 3.3 V
C_OUT – selection of output capacitance for VCORE
If connected, output capacitance is 40 µF, 20 µF otherwise
No jumper
COUT = 20 µF
1-2
COUT = 40 µF
J3
Power supply DC 12 V
J4
Buck-boost/standard buck mode configuration
1-2
3-4
No jumper
J5
Buck-boost configuration
Buck only configuration
VCORE selection
1-2
VCORE = 1.23 V
3-4
VCORE = 3.3 V
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
12
Freescale Semiconductor, Inc.
Getting to Know the Hardware
Table 6. Jumpers J1 through J31 (Including Connectors) (continued)
Schematic
Label
J6
J7
J8
J9
Pin Number
Pin Name
Jumper/Pin Function
Configuration for Boots_core pin
1-2
Boots_core pin connected to GND – used for devices with linear voltage regulator on
VCORE
2-3
Boots_core pin connected to SW_core – used for devices with switching mode power
supply on VCORE
Power supply (max. voltage = 40 V)
This connector should be used to supply EVB from protected voltage source
1
VBAT
Positive supply
2
GND
Ground
Power supply for EVB
Allows disconnecting of all three supply pins for current measurements
Normally (no measurement), jumpers should be connected
1-2
Enables power supply (VBAT_P) for VSUP3 pin of MC34FS6407(or MC34FS6408)
3-4
Enables power supply (VSUP) for VSUP1 and VSUP2 pins of MC34FS6407(or
MC34FS6408)
Compensation network for FB_core – part 2
1-2
VCORE = 1.23 V
3-4
VCORE = 3.3 V
J10
VSNS_EN – connects battery voltage before filter to VSENSE
J11
External transistor for VCCA
1-2
Emitter of Q2 connected to VCCA_E
2-3
External transistor Q2 is not used
J12
IO_0_PD – pulls down IO_0
J13
FS0B pull-up connection
1-2
FS0B pull-up is supplied from VSUP3
2-3
FS0B pull-up is supplied from VDDIO
J14
Connects base of the transistor Q2 to the VCCA_B pin
J15
External resistor bridge monitoring (for future use)
Used in conjunction with J18
Resistor bridge has to be in same configuration as J5
Voltage on this voltage divider has to be adjusted to same level as for first bridge using potentiometer R17
1-2
VCORE = 1.23 V
3-4
VCORE = 3.3 V
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
Freescale Semiconductor, Inc.
13
Getting to Know the Hardware
Table 6. Jumpers J1 through J31 (Including Connectors) (continued)
Schematic
Label
Pin Number
J16
VDDIO tracking
J17
J18
J19
Pin Name
Jumper/Pin Function
1-2
VDDIO tracks VCCA
2-3
VDDIO tracks VCORE
DBG_EN - enables debug mode
No jumper
Normal mode
1-2
Debug mode
DRIFT_MONIT – External resistor bridge monitoring
1-2
Second resistor bridge on IO_1 is disabled
2-3
Reserved for future use
VCCA/VAUX regulator selection
1-3 and 2-4
VAUX is disabled
3-5 and 4-6
VAUX is enabled
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
14
Freescale Semiconductor, Inc.
Getting to Know the Hardware
Table 6. Jumpers J1 through J31 (Including Connectors) (continued)
Schematic
Label
J20
J21
J22
Pin Number
Pin Name
Jumper/Pin Function
Additional Inputs/Output
Fail-safe output
1
FS0B
2
VDDIO
3
MISO
SPI – Master Input Slave Output
4
RSTB
Reset pin – connect to the reset line of the MCU
5
MOSI
SPI – Master Output Slave Input
6
GND
Ground
7
SCLK
SPI – clock
8
GND
Ground
9
NCS
SPI – Chip Select
10
GND
Ground
11
MUX_OUT
12
INTB
13
RXD_L
LIN receive pin – connect to the MCU — Not Available on KIT34FS640xEVB
14
TXD_L
LIN transmit pin – connect to the MCU — Not Available on KIT34FS640xEVB
15
GND
Ground
16
TP5
-
17
RXD
CAN receive pin – connect to the MCU
18
TXD
CAN transmit pin – connect to the MCU
19
DBG
Debug pin
20
GND
Ground
VDDIO voltage
Output from the multiplexer – connect to the MCU's ADC
Interrupt pin – connect to the MCU IO with an interrupt capability
LIN connector
LIN after transceiver (NOT the MCU side) — Not Available on KIT34FS640xEVB
1
LIN
2
GND
Ground
CAN connector
1
CANH
CANH signal after transceiver (NOT the MCU side)
2
CANL
CANL signal after transceiver (NOT the MCU side)
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
Freescale Semiconductor, Inc.
15
Getting to Know the Hardware
Table 6. Jumpers J1 through J31 (Including Connectors) (continued)
Schematic
Label
J23
J24
J25
J26
Pin Number
Pin Name
Jumper/Pin Function
General Inputs/Outputs
pin1
IO_1
-
pin2
IO_0
-
pin3
IO_3
-
pin4
IO_2
-
pin5
IO_5
-
pin6
IO_4
-
pin7
VDDIO
-
pin8
NC
-
pin9
VBAT
-
pin10
GND
-
SPI/USB dongle or MCU connection
SPI/USB dongle should be directly connected to this port
pin1
GND
Ground
pin2
TP18
-
pin3
TP2
-
pin4
TP19
-
pin5
TP3
-
pin6
TP20
-
pin7
TP4
-
pin8
TP21
-
pin9
SCLK
SPI – clock
pin10
TP22
Not connected
pin11
MOSI
SPI – Master Output Slave Input
pin12
TP23
-
pin13
MISO
SPI – Master Input Slave Output
pin14
TP24
-
pin15
NCS
SPI – Chip Select
pin16
TP25
-
Power supply for LEDs on IO_4 and IO_5 (D11, D10)
1-2
Enables power supply for IO_4 (D11)
3-4
Enables power supply for IO_5 (D10)
RSTB_LED_EN – enables LED D14 for RSTB output
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
16
Freescale Semiconductor, Inc.
Getting to Know the Hardware
Table 6. Jumpers J1 through J31 (Including Connectors) (continued)
Schematic
Label
Pin Number
Pin Name
Jumper/Pin Function
J27
INTB_LED_EN – enables LED D15 for INTB output
J28
IO5_OUT – IO_5 output configuration
J29
1-2
IO_5 connected to LED D10 via transistor Q5
2-3
IO_5 pulled down
IO4_OUT – IO_4 output configuration
1-2
IO_4 pulled down
2-3
IO_4 connected to LED D11 via transistor Q6
J30
Enable LED D12 for fail-safe.
J31
Enables LED D13 as indicator of power supply
J32
Enables LED D17 as indicator for VCORE power supply
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
Freescale Semiconductor, Inc.
17
Getting to Know the Hardware
4.8.1
Compensation Network
A voltage regulator needs feedback from the VCORE voltage to be able to adjust (control) output voltage. For this reason, two bridges are
implemented in the external MC34FS6407 or MC34FS6408 circuitry. Static feedback (steady-state) voltage is defined by a simple resistor
bridge (given by RA3/RB3 and RA4). Dynamic behavior of the regulator is controlled by another bridge that is an RC divider (defined by
RBx, CBx, R1, C1, R2, C2). Figure 4 shows the compensation network. Steady-state voltage can be either 1.2 V or 3.3 V. To tune the
dynamic performance, the board is equipped with two different bridges (possible combinations of the jumpers J1 and J9 are shown in
Table 7). The combinations shown in Table 7 are chosen to provide optimal performance for the given output voltage. The real dynamic
performance can differ for different applications and can be tuned by changing the compensation network and by adding output capacitors
(J2).
Table 7. Compensation Network and VCORE Settings
VCORE
(V)
Jumper Settings
Static Behavior
Dynamic Behavior
J5
J1
J9
1.23
3-4
3-4
3-4
3.3
1-2
1-2
1-2
VCORE _sense
VCORE
Figure 4. Compensation Network and VCORE Setup Schematic
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
18
Freescale Semiconductor, Inc.
Getting to Know the Hardware
4.8.2
Second Resistor Bridge - VDRIFT Monitoring
To increase the safety level of an application, a second resistor bridge has been added. This bridge generates the same voltage as the
bridge connected to FB_core pin. If the difference between voltages is greater than VDRIFT, the FS state machine is impacted.
Table 8. VDRIFT Monitoring Settings
VCORE
(V)
Hardware Settings
J15
J18
1.23
1+2
3+4
3.3
3+4
1+2
Invoking this functionality involves both the board hardware and the software configuration. On the hardware side, the second resistor
bridge must be configured by jumper J18, as shown in the Figure 5, and adjusted by the potentiometer R17 to set the same voltage as on
the first bridge. Software sets registers INIT_Vreg1 (bit Vcore_FB to 1) and register INIT_FSSM1 (bit IO_1_FS to 1).
VCORE
J15
IO _ 1 V C OR E FB Drift E n a ble
V COR E
V COR E
Figure 5. Second Resistor Bridge
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
Freescale Semiconductor, Inc.
19
Getting to Know the Hardware
4.9
Switch Definitions
Table 9. Switches
Switch Number
SW1
SW2
SW3
SW4
Position
Function
Description
Power supply select
1-2
Supply from J7 selected
2-3
Power jack on J3 selected
VCCA/VAUX switch
Only one choice is possible at the same time
1
3.3 V / 3.3 V
2
5.0 V / 5.0 V
3
3.3 V / 5.0 V
4
5.0 V / 3.3 V
This setting is not allowed if VAUX is not used - option
VCCA only (selected by J19)
LEDs - indicators for power supplies
1
VPRE
Enables LED indicator for pre-regulator
2
VAUX
Enables LED indicator for auxiliary power supply
3
VCCA
Enables LED indicator for VCCA regulator
4
CAN_5 V
Enables LED indicator for CAN regulator
Ignition switch
1-2
IO_0 connected to VBAT
(ignition key active)
2-3
No voltage on the IO_0
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
20
Freescale Semiconductor, Inc.
Accessory Interface Board
5
Accessory Interface Board
The KIT34FS6407EVB and KIT34FS6408EVB are generally used with the KITUSBSPIDGLEVME interface dongle (see Figure 6), which
provides a bidirectional SPI/USB conversion. This small board makes use of the USB, SPI, and parallel ports built into Freescale’s
MC68HC908JW32 microcontroller. The main function provided by this dongle is to allow Freescale evaluation kits that have a parallel port
to communicate via a USB port to a PC. For more information regarding KITUSBSPIDGLEVME interface dongle, go to
http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=KITUSBSPIDGLEVME.
Figure 6. KITUSBSPIDGLEVME Interface Dongle
For information on setting up the dongle with the EVB, see Section 5.1 "Connecting the KITUSBSPIDGLEVME Interface Dongle".
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
Freescale Semiconductor, Inc.
21
Accessory Interface Board
5.1
Connecting the KITUSBSPIDGLEVME Interface Dongle
A typical connection of KITUSBSPIDGLEVME Interface Dongle (see Section 5 "Accessory Interface Board") to the KIT34FS6407EVB or
KIT34FS6408EVB evaluation board is done through connector J24 (see Figure 7). In this configuration, it is recommended that you use
the EVB in a debug mode (J17 configured as Debug). In this mode there is no timeout used for the INIT phase, so the initialization
commands can be sent anytime. WD refresh is also not mandatory in the debug mode. This means that no action is taken if WD refresh
fails (WD window expires, WD refreshed during closed window, wrong WD answer).
Flip Interface Dongle
upside down
Mount Interface Dongle
to Evaluation Board
KITUSBSPIDGLEVME
KIT34FS6407EVB/KIT34FS6408EVB
Figure 7. Connecting KITUSBSPIDGLEVME to the Evaluation Board
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
22
Freescale Semiconductor, Inc.
Installing the Software and Setting up the Hardware
6
Installing the Software and Setting up the Hardware
6.1
Installing the GUI Software
Two different Graphical User Interfaces (GUI’s) provide the software interface that allows you to communicate with the
KIT34FS6407EVB or the KIT34FS6408EVB.
•
•
SPIGen is Freescale’s generic GUI for use with the KITUSBSPIDGLEVME Interface Dongle.
The MC3390X_GUI is a special purpose graphical user interface designed specifically for MC3390x and MC34FS640x
evaluation boards.
Both GUI’s are similar in function and either may be used with the KIT34FS6407/8 EVBs.
6.1.1
Installing SPIGen on your Computer
The latest version of SPIGen is designed to run on any Windows 8, Windows 7, Vista, or XP-based operating system. To install the
software, do the following:
1.
Download and install SPIGen
a) Go to www.freescale.com/analogtools and find your kit.
b) Click on the kit name to open the corresponding Tool Summary Page
c) On the tool summary page, look for “Jump Start Your Design.” Click on “Get Started with the KIT34FS640xEVB” link.
d) From the list of items that appear, click on “SPI Generator (SPIGen) Software” and follow the sequence of instructions to
begin the download process.
e) After you click the appropriate download button, a large downward arrow appears momentarily at the bottom left corner of
your screen, indicating that the download has begun.
f) When the download completes, an SPIGEN.exe button appears at the bottom left corner of your screen. Click on the
button and select “Run.” A wizard guides you through the installation process.
g) If you instructed the SPIGen wizard to create a short-cut, an SPIGen icon appears on you desktop. If you elected not to
create a short-cut, the SPIGen executable is installed by default at C:Program Files\SPIGen
2. Download the configuration file MC33907_8_SPIGEN.spi.
a) Go to www.freescale.com/analogtools and find your kit.
b) Click on the kit name to open the corresponding Tool Summary Page
c) On the tool summary page, look for “Jump Start Your Design.” Click on ‘Get Started with the KIT34FS640xEVB.”
d) From the list of items that appear, click on “MC33907/MC33908 SPIGen Configuration Modification File.”
e) You will be prompted with the option to Open or Save the file. Select the option to Save.
f) After the download completes successfully, look for MC33907_8_SPIGEN.spi in your system download folder
(C:\Users\xxxx\Downloads).
6.1.2
Installing the MC3390X_GUI on your Computer
1.
Go to www.freescale.com/analogtools and find your kit.
2.
Click on the kit name to open the corresponding Tool Summary Page
3.
On the Tool Summary Page, look for “Jump Start Your Design.” Click on “Get Started with the KIT34FS640xEVB” link.
4.
From the list of items that appear, click on “MC33907/8 Graphical User Interface.” You will be prompted to accept the licensing
agreement.
5.
When you have accepted licensing agreement, click on the download button that appears.
6.
A zip file named “KT33907_8_GUI” will download to your system download folder (C:\Users\xxxx\Downloads.) Click on the zip
file in your system download folder and Unzip the MC3390X_GUI folder into a folder of your choice.
7.
When the Unzip operation is complete, click on the Freescale setup icon that appears in the folder you extracted to. An
Installation wizard guides you through the setup process.
8.
If you elected to create a desktop icon during the setup process, a Freescale MC3390X_GUI icon appears on your desktop. If
you did not opt to create a desktop icon, the icon is located at C:\Program Files (x86)\MC3390X_GUI.
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
Freescale Semiconductor, Inc.
23
Installing the Software and Setting up the Hardware
6.2
Configuring the Hardware
Figure 8 shows the setup required to use KIT34FS6407EVB or KIT34FS6408EVB.
Power Supply
USB Cable
(-)
(+)
KITUSBSPIDGLEVME
KIT34FS6407EVB/KIT34FS6408EVB
KIT34FS6407EVB/34FS6408EVB
Figure 8. Evaluation Board Setup
6.2.1
Step-by-step Instructions for Setting Up the Hardware
Set up the KIT34FS6407EVB/KIT34FS6408EVB hardware and software as follows:
1. Install the software GUI (either SPIGen or MC3390X_GUI) on your computer (See Section 6.1 "Installing the GUI Software".)
2. Flip the KITUSBSPIDGLEVME Interface Dongle over and mount its IO Port connector to Connector J24 on the evaluation board.
3. Connect a USB cable from the Interface Dongle to the PC.
4. Set the EVB jumpers and switches as needed. Refer to Figure 3 for an example.
5. Select Debug or Normal mode with jumper J17.
6. Attach loads to connector JP1 as needed.
7. Attach DC power supply on J3 or J7 (maximum voltage: 40 V).
8. Switch SW1 to supply the board.
9. If SW2 switches are ON and VBAT is set correctly, then VPRE, VCCA, VAUX, CAN_5 V LEDs should turn ON. VBAT value is
dependent on VPRE configuration. In Buck mode, it must be 8.2 V min. FS0B LED should turn ON (J13 / J30 must be plugged).
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
24
Freescale Semiconductor, Inc.
Installing the Software and Setting up the Hardware
6.3
Running the GUI
With the KIT34FS6407/8 EVB’s, you are provided with two separate graphical user interfaces (GUI’s) that allow you to
configure registers:
•
•
SPI generator (SPIGen)
MC3390X_GUI
Both GUI’s are similar in function. You may use either one at your own discretion.
6.3.1
Running SPIGen
To run SPIGen, do the following:
1.
Click on the SPIGen icon. This icon appears on your desktop if you elected to create a short-cut during the installation process.
Otherwise, the icon resides in the folder C:Program Files\SPIGen. The generic SPIGen start-up screen appears.
2.
From the SPIGen menu bar, click on FILE>Open and select the configuration file “MC33907_8_SPIGEN.spi” (previously
downloaded in Section 6.1.1.) Figure 9 shows SPIGen screen with the configuration file installed.
3. In Debug mode, use the SPIGen batch RST_counter_to_0.spi to reset the error counter. FS0B should turn off (LED D12 turned
off).
At this stage, EVB is powered and SPIGen is working. When Normal mode is selected with J17, a valid WD must be sent, otherwise the
device goes into deep fail-safe.
Figure 9. SPIGen Screen
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
Freescale Semiconductor, Inc.
25
Installing the Software and Setting up the Hardware
In order to fill a specific need, it is also possible to edit registers with another value and to save it for further use, either as standalone or
inside a batch.
Figure 10 shows a batch called “RST_counter_to_0”, as an example. This batch file automatically installs when the configuration file is
loaded. To select the batch file, click on the Batch Name box at the bottom right side of the screen.
Figure 10. RST_counter_to_0 Batch
At startup or when resuming from LPOFF mode the reset error counter starts at level 1 and FS0B is asserted low. To remove activation of
FS0B, the RST error counter must go back to value “0” (seven consecutive good WD refresh decreases the reset error counter down to
0) and a right command is sent to FS_OUT register. This can be demonstrated with this batch running in debug mode.
The batch shown in Figure 10 executes the following action:
– WD_Window_DIS_xCD0C:
• Disables normal WD
– INIT_FSSM2_xCB0C:
• IO_23_FS bits configured in “NOT SAFETY” mode
– WD_answer1 to WD_answer7:
• If the part is in debug mode, this sends the right first WD answer and allows the reset counter to change to 0
– FS_OUT_xD327:
• Disables FS0B pin, coming back to high level (D12 turned off)
– INIT_INT_x8C00:
• Closes the init phase of the main state machine
– CAN_MODE_B0C0:
• Enables CAN transceiver
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
26
Freescale Semiconductor, Inc.
Installing the Software and Setting up the Hardware
6.3.2
Running the MC3390X_GUI
The MC3390X_GUI allows you to program all SPI features by using a friendly interface. Advanced users can also use MC3390X_GUI to
modify the register table manually.
1.
To launch the MC3390X_GUI application, click on the application icon located either on your desktop or in Program Files menu
as shown in Figure 11.
Figure 11. Launching MC3390X_GUI application
2.
When the MC3390X_GUI launches, click on the dropdown box under “Choose Interface” and select the appropriate device.
(See Figure 12.)
Click
Here
Select Your
Device
Figure 12. MC3390X_GUI Device Selection
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
Freescale Semiconductor, Inc.
27
Installing the Software and Setting up the Hardware
Click on the “KIT3390xxEEVB” button on the left side of the screen. (See Figure 13.)
Click
Here
Figure 13. MC3390X_GUI Configuration Selection
3.
A screen similar to the one in Figure 14 appears showing the status of the registers at startup. In this example, register
INIT_FSSM2 has bit IO_23_FS configured as SAFETY CRITICAL.
Figure 14. MC3390X_GUI Main Screen
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
28
Freescale Semiconductor, Inc.
Installing the Software and Setting up the Hardware
4. In the right side of the GUI, select NOT SAFETY and send the command as shown in Figure 15.
Figure 15. MC3390X_GUI Register
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
Freescale Semiconductor, Inc.
29
Initialization and Configuration Mode
7
Initialization and Configuration Mode
7.1
INIT Phase
INIT registers are set to their default values after each POR (power-on reset.) This default configuration is compatible with the default EVB
settings except for the INIT FSSM2 register. Bit IO_23_FS in this register is set by default, which means the fail-safe outputs (FCCU_x of
the MPC5643L or similar device) have to be connected to the IO’s 2 and 3 of the MC34FS6407or MC34FS6408. If MPC5643L (or a similar
device) is not used, the bit IO_23_FS has to be cleared during INIT phase (setting shown in Table 10). The INIT phase of the main part
completes with a Write command to the INIT_INT register. This command closes access to the INIT registers and the device goes into
Normal mode. The same sequence (INIT_FSSM2, INIT_INT) must occur in both Debug and Standard mode. The only difference is in the
timeout constraints used for the Standard mode. In the Standard mode, INIT commands have to be sent before the 256 ms timer (starting
from the RST pin release) expires.
Table 10. INIT FSSM2 Setting
MOSI
MOSI
7.2
bit15
bit14
bit13
bit12
bit11
bit10
bit9
bit8
bit7
bit6
bit5
bit4
bit3
bit2
bit1
bit0
1
1
0
0
1
0
1
P
RSTB_
err_FS
IO_23_
FS
PS
F_FS1
Secure
_3
Secure
_2
Secure
_1
Secure
_0
bit15
bit14
bit13
bit12
bit11
bit10
bit9
bit8
bit7
bit6
bit5
bit4
bit3
bit2
bit1
bit0
1
1
0
0
1
0
1
1
0
0
0
1
1
0
0
0
Normal Operation
During normal operation (after INIT phase), both modes (Normal and Debug) allow you to send to send a WD refresh command. In Debug
mode, no action is taken on a bad WD response. In Normal mode, the KITUSBSPIDGLEVMESPI interface dongle cannot guarantee the
WD refresh period (Windows XP and Windows 7 are not real-time operating systems.) Nevertheless, WD refresh works in Standard mode
using a WD window duration of 512 ms (reconfigured in the INIT phase).
7.3
Debug Mode
The KIT34FS6407EVB or KIT34FS6408EVB is mainly intended to be used in Debug mode. In Normal mode you must either use an MCU
that is able to manage the WD or you must disable WD. If WD is enabled, you must send a valid WD response at startup. The response
must occur within the 256 ms windows after reset release. You must then update WD at the right time. With KIT34FS6407EVB or
KIT34FS6408EVB attached to the KITUSBSPIDGLEVME, this must be done manually (which is feasible, depending on the device’s
register configuration.)
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
30
Freescale Semiconductor, Inc.
GND
1
2
GND
A
J10
IO_1
R52
510K
GND
1
2
3
Vsup3
2
R13
4.32K
R24
5.1K
GND
1
2
2K
D2
2K
LIN
A
1N4148WS
C37
1000PF
R50
GND
R141
C
J26
INTb
RSTb
2
1
R39
1.5K
RED
D14
VDDIO
2
1
J27
R40
1.5K
RED
D15
LED Signalling
1uH
IO_5
GND
C89
2.2UF
J28
R45
510K
R41
5.1K
J12
1
2
FS0_b
J22
1
4
2
Q5
3
1
ON
OFF
CANH
J25
PGND
LED/GRN
D10
4 2
3 1
Vpre
CANL
R33
1.5K
DNP
R28 10K
J17
GND
CB31
10nF
IO_1
IO_3
IO_5
1
R46
510K
LED/GRN
D11
R42
Q6
5.1K
R34
1.5K
VDDIO
Vbat
DEBUG
NORMAL
VSUP1
VSUP2
VSENSE
VSUP3
NC1
GND_COM
CAN_5V
CANH
CANL
IO_4
IO_5
IO_0
U1
J29
1
3
5
7
9
C30
10nF
DBG
C4
0.1UF
R30
11.0K
GND
2
4
6
8
10
GND
R44
5.1K
IO_4
J23
I/O
GND
IO_1
FS0b
J17-DEBUG MODE
CAN
R51
60.4
VDDIO
FS0b_PU
R63
5.1K
GND
C31
10nF
Vpre
R29
5.1K
Vsup3
J13
CANH
CANL
IO_4
IO_5
IO_0
Vsense
C46
10nF
C45
10nF
1
2
3
4
5
6
7
8
9
10
11
12
DNP
PGND
DNP
GND
IO_0
CAN_5V
C49
0.1UF
GND
J8
GND
GND
PLUG_1X2
GND
R11
5.1K
C47
220PF
DNP
LIN
C27
4.7uF
Vsup
PGND
2
R53
5.1K
Contact KEY
ÀÁ
GND
Vbat
CAN_5V
C44
10nF
R43
5.1K
GND
C28
4.7uF
L4
1
PGND
VSW
PGND
R67
4.7
36
35
34
33
32
31
30
29
28
27
26
25
49
{2}
PGND
Vcca
Vaux
Vpre
IO_2
IO_3
TXD
RXD
TXD_L
RXD_L
C36
10nF
Vbat
Vcore
TP2
TP3
TP4
GND
1
2
3
4
GND
0
1 3
PGND
J31
J32
SW3
8
7
6
5
RSTb
VDDIO
R47
1.2K
A
LED/GRN
D13
LED/GRN
GND
C
C
C R37 560
D9
LED/GRN
A
D17
C
D8
LED/GRN
A
R36 560
C R32 560
D7
LED/GRN
A
1.5K
GND
PGND
RXD
DBG
FS0_b
MISO
MOSI
SCLK
NCSb
MUX_OUT
RXD_L
GND
FS0b
J30
MMSZ5248ET1
D16
J20
2
1
R38
5.6K
2
4
6
8
10
12
14
16
18
20
DEBUG
1
3
5
7
9
11
13
15
17
19
33906
33907_8
2 - 3
J6
C14
0.1UF
J6
1 - 2
1
GND
R35
510K
FS0b_PU
GND
R48
10K
RED
D12
Q7
TXD
INTb
TXD_L
GND
RSTb
VDDIO
JP1
PLUG_1X10
1
2
3
4
5
6
7
8
9
10
TP5
GND
PGND
C24
0.22uF
GNDGND
C48
0.1UF
Vpre
1
CAN_5V
Vaux
Vcca
Vcore
2
J16
GND
C5
0.1UF
Boost_core
VSW_Core
Power Supply
3
INTb
GND
PGND
C6
1000PF
C
R31
TP18
TP19
TP20
TP21
TP22
TP23
TP24
TP25
Vcca
VDDIO
Vcore
GND
D6
2
4
6
8
10
12
14
16
GND
DNP
C43
1000PF
VDDIO
CB29
10nF
DNP
Vcore
MTG1
BH3
L5
J2
1
2
COUT4
10uF
PGND
10uF
1
2
3
4
SW2
C33
4.7uF
1
J11
1
2
3
Vcca
8
7
6
5
GND
Vpre
51K
R49
TP17
GND
TP16
GND
MTG1
BH4
MTG1
TP15
GND
TP11
TP39
TP14
GND
TP9
TP36
TP7
TP27
TP13
BH2
{2}
CAN_5V
GND
Vcca
PGND
Vpre
GND
1
1
1
1
1
24K
R27
TP12
GND
TP10
TP38
TP8
TP37
TP6
5.1K
{2}
R23 12K
Test Points
J5
2 4
Vcore
GND
GND
GND
GND
Vsup3
GND
Vaux
PGND
J9
RB2
39K
GND
J19
Vaux_B
1
2
4
6
C23
4.7uF
Vaux_Emitter
1
3
5
1 3
2 4
CB1
220PF
Vaux
Comp_core
CB2
1000PF
2 4
1 3
RB1
200
J1
GND
Vaux_E
Vaux_Emitter
Vaux
Q3
NJT4030P
C2
150pF
R2
18K
C1
680PF
R1
510
Vcore
TP40
TP35
TP34
TP33
TP32
TP31
TP30
TP29
TP28
VSW_Core
VSW
INTb
RSTb
FS0b
MUX_OUT
LIN
CANL
CANH
Regulator
VCCA only
VAUX & VCCA
Jumper
1-3 & 2-4
3-5 & 4-6
J19
Vcca/Vaux regulator select.
Vpre
GND
RA4
8.06K
1 3
RA3
RB3
FB_Core
Vcca
R22
Q2
NJT4030P
Vcca_E
SWITCH Vcca / Vaux Vcca only
1-8
3.3
3.3
3.3
2-7
5
5
5
3-6
3.3
5
NA
5
3.3
4-5
5
TP26
C8
10nF
PGND
J1 / J5 / J9
1 - 2 Vcore = 1.23V
3 - 4 Vcore = 3.3V
PGND
10uF
SW2
Vcca/Vaux Voltages config.
SELECT
VCCA_B
J14
Vcore_sense
COUT2 COUT3
COUT1 10uF
4.32K
2.2uH
2
D5
SS22T3G
PGND
MTG1
BH1
R140
4.7
C88
4700PF
1
24.9K
Vpre
PGND PGND
10uF 10uF 10uF
10uF
PGND
CB21 CC21 C29
C21
LED/GRN
A
J24
R142 560 A
1
3
5
7
9
11
13
15
SPI
MUX_OUT
C32
1000PF
SCLK
MOSI
MISO
NCSb
R26
GND
R64 5.1K
NCSb
SCLK
MOSI
MISO
Boost_core
VSW_Core
Vcore_sense
Comp_core
FB_core
SELECT
GND
PGND
J4
2 4
MBRS340T3G
C
J4-Vpre mode
Buck only
1-2 & 3-4
Jumpers off Buck or Boost
1
BUK9832-55A
Q1
D1
MBRS340T3G
MC34FS6407NAE
CAN_5V
{2}
GND
EP
BOOT_CORE
SW_CORE
VCORE_SNS
COMP_CORE
FB_CORE
SELECT
VDDIO
INT
CS
SCLK
MOSI
MISO
IO_0
IO_2
IO_4
C
A
Vpre
C11
4700PF
D3
A
C
A
22uH
2
4
3
L3
2
2
Vsense
DNP
Vsup3
R25
5.6K
Feature supported only with
MC33907LAE & MC33908LAE
PLUG_1X2
DNP
J21
LIN
R15
24.9K
S1
1
GND
GND
J15
R17
5.0K
1 3
2 4
Vcore
GND
C22
1uF
GND GND
J18-IO_1 Configuration
1 - 2 IN / OUT
2 - 3 VcoreFB drift
J18
1 - 2 Vcore = 1.23V
3 - 4 Vcore = 3.3V
A
C
A
C
Vsup3
CB20
C20 10nF
47uF DNP
+
C
D4
SBRS81100T3G
Vbat
J15
IO_1 VcoreFB Drift Enable
GND
PLUG_1X2
J7
Vbat
S1
1
2
3
1
2
SW1
500SSP3S1M6QEA S2
3
1
GND
3
1
3
3
2
3
GND
1
1
2
A
C
3
2
1
2
VCCA
VCCA_B
VCCA_E
VAUX_E
VAUX_B
VAUX
48
47
46
45
44
43
42
41
40
39
38
37
SW_PRE1
SW_PRE2
BOOT_PRE
DGND
GATE_LS
VCCA
VCCA_B
VCCA_E
VAUX_E
VAUX_B
VAUX
VPRE
IO_1
FS0
DEBUG
AGND
MUX_OUT
IO_2
IO_3
TXD
RXD
NC2
NC3
RST
13
14
15
16
17
18
19
20
21
22
23
24
1
J3
3
1
2
1
3
2
2
3
SW4
500SSP3S1M6QEA S2
1
2
A
C3
2
C
A
3
GND
1
2
1
2
2
B
A
3
E
C
C
B
2
4
E
Freescale Semiconductor, Inc.
2
4
8
C
Vbat Jack
Schematic
Schematic
Figure 16. Evaluation Board Schematic
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
31
Board Layout
9
Board Layout
9.1
Assembly Layer Top
KIT34FS640XEVB REV A
2015 FREESCALE
Figure 17. KIT34FS6407EVB/KIT34FS6408EVB Assembly Layer Top
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
32
Freescale Semiconductor, Inc.
Board Layout
9.2
Assembly Layer Bottom
.
Figure 18. KIT34FS6407EVB/KIT34FS6408EVB Assembly Layer Bottom
NOTE:
This image is an exception to the standard top-view mode of representation used
in this document. It has been flipped to show a bottom view.
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
Freescale Semiconductor, Inc.
33
Board Layout
9.3
Bill of Materials
Table 11. Bill of Materials (1)
Item
Qty
Schematic Label
Value
Manufacturer
Part Number
Assy Opt
Active Components
1
1
U1
Freescale Semiconductor
MC34FS6407 or MC34FS6408
(3)
Capacitors
2
1
C1
680 pF
KEMET
C0603C681J5GAC
3
1
C2
150 pF
KEMET
C0603C151J5GAC
4
5
C4, C5, C14, C48, C49
0.1 μF
KEMET
C0603C104K3RAC
5
4
C6, C32, C37, CB2
1000 pF
AVX
06035U102KAT2A
6
4
C8, C30, C31, C36
10 nF
AVX
06035C103JAT2A
7
2
C11, C88
4700 pF
Yageo America
CC0603KRX7R9BB472
8
1
C20
47 μF
Nippon Chemi-Con Corporation EMVH500ADA470MJA0G
9
4
C21, C29, CB21, CC21
10 μF
TDK
CGA6M3X7R1C106K
10
1
C22
1.0 μF
TDK
CGA5L3X7R1H105K160AB
11
2
C23, C33
4.7 μF
Murata
GCM31CR71C475KA37
12
1
C24
0.22 μF
KEMET
C0603C224K3RACTU
13
2
C27, C28
4.7 μF
Murata
GCM32ER71H475KA55L
14
1
C43
1000 pF
AVX
06035U102KAT2A
(2)
15
6
C44, C45, C46, CB20, CB29, CB31 10 nF
AVX
06035C103JAT2A
(2)
16
1
C47
220 pF
KEMET
C0603C221K5GACTU
(2)
17
1
C89
2.2 μF
AVX
08053C225KAT2A
18
1
CB1
220 pF
KEMET
C0603C221K5GACTU
19
4
COUT1, COUT2, COUT3, COUT4
10 μF
Murata
GCM32ER71E106KA57
(3)
20
2
D1, D3
MBRS340T3G
ON Semiconductor
MBRS340T3G
(3)
21
1
D2
1N4148WS
Diodes Inc
1N4148WS-7-F
22
1
D4
SBRS81100T3G
ON Semiconductor
SBRS81100T3G
23
1
D5
SS22T3G
ON Semiconductor
SS22T3G
24
8
D6, D7, D8, D9, D10, D11, D13,
D17
LED/GRN
OSRAM
LP M67K-E2G1-25
25
3
D12, D14, D15
RED
OSRAM
LS M67K-H2L1-1-0-2-R18-Z
26
1
D16
MMSZ5248ET1
ON Semiconductor
MMSZ5248BT1G
(3)
Diodes
(3)
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
34
Freescale Semiconductor, Inc.
Board Layout
Table 11. Bill of Materials (1) (continued)
Item
Qty
Schematic Label
Value
Manufacturer
Part Number
Assy Opt
Connectors
27
7
J1, J4, J5, J8, J9, J15, J25
HDR 2X2
Samtec
TSW-102-07-G-D
28
10
J2, J10, J12, J14, J17, J26, J27,
J30, J31, J32
HDR 1X2
Samtec
TSW-102-07-T-S
29
1
J3
CON_1_PWR
CUI Stack
PJ-102AH
30
7
J6, J11, J13, J16, J18, J28, J29
HDR_1X3
Tyco Electronics
826629-3
31
3
J7, J21, J22
PLUG_1X2
Phoenix contact
1803277
32
1
J19
HDR 2X3
Tyco Electronics
1-87215-2
33
1
J20
HDR_10X2
Samtec
TSW-110-07-S-D
34
1
J23
HDR 2X5
Samtec
TSW-105-07-G-D
35
1
J24
NPPC082KFMS-R Sullins Electronics Corp
C
NPPC082KFMS-RC
36
1
JP1
PLUG_1X10
Phoenix contact
1803358
Inductors
37
1
L3
22μH
EPCOS
B82479G1223M000
(3)
38
1
L4
1.0 μH
EPCOS
B82472G6102M000
(3)
39
1
L5
2.2 μH
EPCOS
B82472G6222M000
Transistors
40
1
Q1
BUK9832-55A
NXP Semiconductors
BUK9832-55A,115
(3)
41
2
Q2, Q3
NJT4030P
ON Semiconductor
NJT4030PT3G
(3)
42
2
Q5, Q6
MMBF0201NLT1
G
ON Semiconductor
MMBF0201NLT1G
43
1
Q7
BSS84LT1
ON Semiconductor
BSS84LT1G
Resistors
44
1
R1
510 K
Bourns
CR0603-JW-511ELF
45
1
R2
18 K
KOA Speer
RK73H1JTTD1802F
46
10
R11, R24, R29, R41, R42, R43,
R44, R53, R63, R64
5.1 K
Vishay Intertechnology
CRCW06035K10JNEA
47
2
R13, RB3
4.32 K
KOA Speer
RK73H1JTTD4321F
48
2
R15, RA3
24.9 K
KOA Speer
RK73H1JTTD2492F
49
1
R17
5.0 K
Bourns
3224W-1-502E
50
1
R22
5.1 K
KOA Speer
RK73H1JTTD5101F
51
1
R23
12 K
Bourns
CR0603-JW-123ELF
52
1
R25
5.6 K
KOA Speer
RK73H1JTTD7151F
53
1
R26
0
Vishay Intertechnology
CRCW06030000Z0EA
54
1
R27
24 K
Panasonic
ERJ-3GEYJ243V
55
2
R28, R48
10 K
KOA Speer
RK73B1JTTD103J
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
Freescale Semiconductor, Inc.
35
Board Layout
Table 11. Bill of Materials (1) (continued)
Item
Qty
Schematic Label
Value
Manufacturer
Part Number
56
1
R30
11 K
KOA Speer
RK73H1JTTD1102F
57
5
R31, R33, R34, R39, R40
1.5 K
Bourns
CR0603-JW-152ELF
R32, R36, R37, R142
560 K
KOA Speer
RK73B1JTTD561J
58
59
3
R35, R45, R46, R52
510 K
KOA Speer
RC0603JR-07510KL
60
1
R38
5.6 K
KOA Speer
RK73B1JTTD562J
61
1
R47
1.2 K
KOA Speer
RK73H1JTTD1201F
62
1
R49
51 K
Vishay Intertechnology
CRCW060351K0JNEA
63
2
R50, R141
2.0 K
Yageo
RC1206JR-072KL
64
1
R51
60.4
KOA Speer
RK73H1JTTD60R4F
65
2
R67, R140
4.7
Bourns
CR0603-JW-4R7ELF
66
1
RA4
8.06 K
KOA Speer
RK73H1JTTD8061F
67
1
RB1
200 K
KOA Speer
RK73B1JTTD201J
68
1
RB2
39 K
KOA Speer
RK73H1JTTD3902F
Assy Opt
Switches
69
2
SW1, SW4
500SSP3S1M6QE E Switch
A
500SSP3S1M6QEA
70
2
SW2, SW3
SW_DIP-4_SM
Grayhill
78RB04ST
Test Points
71
12
TP2, TP3, TP4, TP5, TP18, TP19,
TP20, TP21, TP22, TP23, TP24,
TP25
TP_PTH
NOT A COMPONENT
NOT A COMPONENT
72
5
TP6, TP7, TP8, TP9, TP10
5006
Keystone Electronics
5006
73
7
TP11, TP12, TP13, TP14, TP15,
TP16, TP17
TESTLOOP_BLA
CK
Keystone Electronics
5011
74
15
TP26, TP27, TP28, TP29, TP30,
TP31, TP32, TP33, TP34, TP35,
TP36, TP37, TP38, TP39, TP40
TESTLOOP_RED Keystone Electronics
5010
(2)
Notes
1. Freescale does not assume liability, endorse, or warrant components from external manufacturers that are referenced in circuit drawings or tables.
While Freescale offers component recommendations in this configuration, it is the customer’s responsibility to validate their application.
2. Do not populate.
3. Critical components. For critical components, it is vital to use the manufacturer listed.
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
36
Freescale Semiconductor, Inc.
References
10
References
Following are URLs where you can obtain information on related Freescale products and application solutions:
Freescale.com Support
Pages
Description
URL
KIT34FS6407EVB
Tool Summary
Page
http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=KIT34FS6407EVB
MC34FS6407
Product
Summary Page
http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=MC34FS6407
KIT34FS6408EVB
Tool Summary
Page
http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=KIT34FS6408EVB
MC34FS6408
Product
Summary Page
http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=MC34FS6408
SPIGen
Software
http://www.freescale.com/files/soft_dev_tools/software/device_drivers/SPIGen.html
KITUSBSPIDGLEVME Interface Dongle http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=KITUSBSPIDGLEVME
10.1
Support
Visit www.freescale.com/support for a list of phone numbers within your region.
10.2
Warranty
Visit www.freescale.com/warranty to submit a request for tool warranty.
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
Freescale Semiconductor, Inc.
37
Revision History
11
Revision History
Revision
Date
Description of Changes
1.0
6/2015
• Initial Release
8/2015
• Corrected typo
KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015
38
Freescale Semiconductor, Inc.
How to Reach Us:
Information in this document is provided solely to enable system and software implementers to use Freescale products.
Home Page:
freescale.com
There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits based
Web Support:
freescale.com/support
Freescale reserves the right to make changes without further notice to any products herein. Freescale makes no
on the information in this document.
warranty, representation, or guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any
and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be
provided in Freescale data sheets and/or specifications can and do vary in different applications, and actual performance
may vary over time. All operating parameters, including “typicals,” must be validated for each customer application by
customer’s technical experts. Freescale does not convey any license under its patent rights nor the rights of others.
Freescale sells products pursuant to standard terms and conditions of sale, which can be found at the following address:
freescale.com/SalesTermsandConditions.
Freescale and the Freescale logo, Energy Efficient Solutions, and SafeAssure logo are trademarks of Freescale
Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. SMARTMOS is a trademark of Freescale Semiconductor, Inc. All other
product or service names are the property of their respective owners.
© 2015 Freescale Semiconductor, Inc.
Document Number: KT34FS6407-34FS6408UG
Rev. 1.0
8/2015