IRF AUIRFR2607ZTR

PD - 96323
AUTOMOTIVE MOSFET
AUIRFR2607Z
HEXFET® Power MOSFET
Features
l
l
l
l
l
l
l
D
Advanced Process Technology
Ultra Low On-Resistance
175°C Operating Temperature
Fast Switching
Repetitive Avalanche Allowed up to Tjmax
Lead-Free, RoHS Compliant
Automotive Qualified *
V(BR)DSS
75V
RDS(on) typ.
17.6mΩ
max.
G
S
Description
22mΩ
ID (Silicon Limited)
45A k
ID (Package Limited)
42A
D
Specifically designed for Automotive applications, this
HEXFET® Power MOSFET utilizes the latest processing
techniques to achieve extremely low on-resistance per
silicon area. Additional features of this design are a 175°C
junction operating temperature, fast switching speed and
improved repetitive avalanche rating . These features
combine to make this design an extremely efficient and
reliable device for use in Automotive applications and a wide
variety of other applications.
G
D
S
D-Pak
AUIRFR2607Z
Absolute Maximum Ratings
G
D
S
Gate
Drain
Source
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These
are stress ratings only; and functional operation of the device at these or any other condition beyond those indicated in
the specifications is not implied.Exposure to absolute-maximum-rated conditions for extended periods may affect device
reliability. The thermal resistance and power dissipation ratings are measured under board mounted and still air conditions.
Ambient temperature (TA) is 25°C, unless otherwise specified.
ID @ TC = 25°C
ID @ TC = 100°C
ID @ TC = 25°C
IDM
PD @TC = 25°C
Continuous Drain Current, VGS @ 10V (Silicon Limited)
Continuous Drain Current, VGS @ 10V (Silicon Limited)
Continuous Drain Current, VGS @ 10V (Package Limited)
c
Pulsed Drain Current
Power Dissipation
Linear Derating Factor
VGS
Gate-to-Source Voltage
EAS
Single Pulse Avalanche Energy (Thermally limited)
EAS (Tested )
Single Pulse Avalanche Energy Tested Value
IAR
Avalanche Current
EAR
Repetitive Avalanche Energy
TJ
Operating Junction and
TSTG
Storage Temperature Range
Soldering Temperature, for 10 seconds
Mounting Torque, 6-32 or M3 screw
Thermal Resistance
Parameter
RθJC
Junction-to-Case
RθJA
Junction-to-Ambient (PCB mount)
RθJA
Junction-to-Ambient
c
j
h
g
i
d
k
45
32
42
180
110
0.72
± 20
96
96
See Fig.12a, 12b, 15, 16
A
W
W/°C
V
mJ
A
mJ
-55 to + 175
°C
300 (1.6mm from case )
10 lbf in (1.1N m)
y
Typ.
–––
–––
–––
y
Max.
1.38
50
110
Units
°C/W
HEXFET® is a registered trademark of International Rectifier.
*Qualification standards can be found at http://www.irf.com/
www.irf.com
1
08/24/10
AUIRFR2607Z
Static Electrical Characteristics @ TJ = 25°C (unless otherwise specified)
Parameter
V(BR)DSS
∆V(BR)DSS/∆TJ
RDS(on)
VGS(th)
gfs
IDSS
IGSS
Drain-to-Source Breakdown Voltage
Breakdown Voltage Temp. Coefficient
Static Drain-to-Source On-Resistance
Gate Threshold Voltage
Forward Transconductance
Drain-to-Source Leakage Current
Gate-to-Source Forward Leakage
Gate-to-Source Reverse Leakage
Min. Typ. Max. Units
75
–––
–––
2.0
36
–––
–––
–––
–––
–––
0.074
17.6
–––
–––
–––
–––
–––
–––
–––
–––
22
4.0
–––
20
250
200
-200
Conditions
V VGS = 0V, ID = 250µA
V/°C Reference to 25°C, ID = 1mA
mΩ VGS = 10V, ID = 30A
V VDS = VGS, ID = 50µA
S VDS = 25V, ID = 30A
VDS = 75V, VGS = 0V
µA
VDS = 75V, VGS = 0V, TJ = 125°C
VGS = 20V
nA
VGS = -20V
e
Dynamic Electrical Characteristics @ TJ = 25°C (unless otherwise specified)
Parameter
Qg
Qgs
Qgd
td(on)
tr
td(off)
tf
LD
Total Gate Charge
Gate-to-Source Charge
Gate-to-Drain ("Miller") Charge
Turn-On Delay Time
Rise Time
Turn-Off Delay Time
Fall Time
Internal Drain Inductance
LS
Internal Source Inductance
Ciss
Coss
Crss
Coss
Coss
Coss eff.
Input Capacitance
Output Capacitance
Reverse Transfer Capacitance
Output Capacitance
Output Capacitance
Effective Output Capacitance
Conditions
Min. Typ. Max. Units
–––
–––
–––
–––
–––
–––
–––
34
8.9
14
14
59
39
28
51
–––
–––
–––
–––
–––
–––
–––
4.5
–––
–––
7.5
–––
–––
–––
–––
–––
–––
–––
1440
190
110
720
130
230
–––
–––
–––
–––
–––
–––
nC
ns
nH
pF
ID = 30A
VDS = 60V
VGS = 10V
VDD = 38V
ID = 30A
RG = 15 Ω
VGS = 10V
e
e
Between lead,
6mm (0.25in.)
from package
and center of die contact
VGS = 0V
VDS = 25V
ƒ = 1.0MHz
VGS = 0V, VDS = 1.0V, ƒ = 1.0MHz
VGS = 0V, VDS = 60V, ƒ = 1.0MHz
VGS = 0V, VDS = 0V to 60V
f
Diode Characteristics
Parameter
IS
ISM
VSD
trr
Qrr
ton
Continuous Source Current
(Body Diode)
Pulsed Source Current
(Body Diode)
Diode Forward Voltage
Reverse Recovery Time
Reverse Recovery Charge
Forward Turn-On Time
c
Min. Typ. Max. Units
45
k
–––
–––
–––
–––
180
–––
–––
–––
–––
30
28
1.3
45
42
A
V
ns
nC
Conditions
MOSFET symbol
showing the
integral reverse
p-n junction diode.
TJ = 25°C, IS = 30A, VGS = 0V
TJ = 25°C, IF = 30A, VDD = 38V
di/dt = 100A/µs
e
e
Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD)
Notes  through ‰ are on page 3
2
www.irf.com
AUIRFR2607Z
Qualification Information
†
Automotive
(per AEC-Q101)
Qualification Level
Moisture Sensitivity Level
Machine Model
††
Comments:
This part number(s) passed
Automotive qualification. IR’s Industrial and
Consumer qualification level is granted by
extension of the higher Automotive level.
D PAK
MSL1
Class M4(425V)
(per AEC-Q101-002)
ESD
Human Body Model
Class H1B(1000V)
(per AEC-Q101-001)
Charged Device
Model
RoHS Compliant
Class C5(1125V)
(per AEC-Q101-005)
Yes
† Qualification standards can be found at International Rectifier’s web site: http//www.irf.com/
†† Exceptions to AEC-Q101 requirements are noted in the qualification report.
Notes:
 Repetitive rating; pulse width limited by
max. junction temperature. (See fig. 11).
‚ Limited by TJmax, starting TJ = 25°C, L = 0.21mH
RG = 25Ω, IAS = 30A, VGS =10V. Part not
recommended for use above this value.
ƒ Pulse width ≤ 1.0ms; duty cycle ≤ 2%.
„ Coss eff. is a fixed capacitance that gives the
same charging time as Coss while VDS is rising
from 0 to 80% VDSS .
www.irf.com
… Limited by T Jmax , see Fig.12a, 12b, 15, 16 for typical
repetitive avalanche performance.
† This value determined from sample failure population. 100%
tested to this value in production.
‡ When mounted on 1" square PCB (FR-4 or G-10 Material) .
For recommended footprint and soldering techniques refer to
application note #AN-994
ˆ Rθ is measured at TJ approximately 90°C
‰ Calculated continuous current based on maximum allowable
junction temperature. Package limitation current is 42A
3
AUIRFR2607Z
1000
1000
100
BOTTOM
TOP
10
1
4.5V
≤ 60µs PULSE WIDTH
Tj = 25°C
ID, Drain-to-Source Current (A)
ID, Drain-to-Source Current (A)
TOP
VGS
15V
10V
8.0V
7.0V
6.0V
5.5V
5.0V
4.5V
100
BOTTOM
4.5V
10
≤ 60µs PULSE WIDTH
Tj = 175°C
0.1
1
0.1
1
10
100
0.1
VDS, Drain-to-Source Voltage (V)
10
100
Fig 2. Typical Output Characteristics
60
Gfs, Forward Transconductance (S)
1000.0
ID, Drain-to-Source Current(Α)
1
VDS , Drain-to-Source Voltage (V)
Fig 1. Typical Output Characteristics
100.0
TJ = 175°C
10.0
TJ = 25°C
1.0
VDS = 20V
≤ 60µs PULSE WIDTH
0.1
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
VGS, Gate-to-Source Voltage (V)
Fig 3. Typical Transfer Characteristics
4
VGS
15V
10V
8.0V
7.0V
6.0V
5.5V
5.0V
4.5V
10.0
TJ = 25°C
50
40
TJ = 175°C
30
20
10
VDS = 10V
380µs PULSE WIDTH
0
0
10
20
30
40
ID, Drain-to-Source Current (A)
Fig 4. Typical Forward Transconductance
Vs. Drain Current
www.irf.com
AUIRFR2607Z
2400
VGS, Gate-to-Source Voltage (V)
2000
C, Capacitance (pF)
20
VGS = 0V,
f = 1 MHZ
Ciss = Cgs + Cgd, Cds SHORTED
Crss = Cgd
Coss = Cds + Cgd
1600
Ciss
1200
800
400
Coss
Crss
VDS = 60V
VDS= 30V
VDS= 12V
16
12
8
4
FOR TEST CIRCUIT
SEE FIGURE 13
0
0
1
ID= 30A
10
0
100
30
40
50
Fig 6. Typical Gate Charge Vs.
Gate-to-Source Voltage
Fig 5. Typical Capacitance Vs.
Drain-to-Source Voltage
1000
ID, Drain-to-Source Current (A)
1000.0
ISD, Reverse Drain Current (A)
20
QG Total Gate Charge (nC)
VDS , Drain-to-Source Voltage (V)
100.0
TJ = 175°C
10.0
1.0
10
TJ = 25°C
OPERATION IN THIS AREA
LIMITED BY R DS (on)
100
100µsec
10
1
10msec
Tc = 25°C
Tj = 175°C
Single Pulse
VGS = 0V
1msec
DC
0.1
0.1
0.0
0.4
0.8
1.2
1.6
2.0
VSD, Source-to-Drain Voltage (V)
Fig 7. Typical Source-Drain Diode
Forward Voltage
www.irf.com
2.4
1
10
100
1000
VDS , Drain-toSource Voltage (V)
Fig 8. Maximum Safe Operating Area
5
AUIRFR2607Z
50
RDS(on) , Drain-to-Source On Resistance
(Normalized)
2.5
LIMITED BY PACKAGE
ID , Drain Current (A)
40
30
20
10
0
25
50
75
100
125
150
ID = 30A
VGS = 10V
2.0
1.5
1.0
0.5
175
-60 -40 -20
TC , Case Temperature (°C)
0
20 40 60 80 100 120 140 160 180
TJ , Junction Temperature (°C)
Fig 10. Normalized On-Resistance
Vs. Temperature
Fig 9. Maximum Drain Current Vs.
Case Temperature
Thermal Response ( ZthJC )
10
1
D = 0.50
0.20
0.10
0.1
τJ
0.05
0.02
0.01
R1
R1
τJ
τ1
R2
R2
τC
τ2
τ1
τ2
τ
Ri (°C/W) τi (sec)
0.71826 0.000423
0.66173 0.004503
Ci= τi/Ri
Ci i/Ri
0.01
SINGLE PULSE
( THERMAL RESPONSE )
Notes:
1. Duty Factor D = t1/t2
2. Peak Tj = P dm x Zthjc + Tc
0.001
1E-006
1E-005
0.0001
0.001
0.01
0.1
t1 , Rectangular Pulse Duration (sec)
Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case
6
www.irf.com
15V
DRIVER
L
VDS
D.U.T
RG
20V
VGS
+
V
- DD
IAS
tp
A
0.01Ω
Fig 12a. Unclamped Inductive Test Circuit
V(BR)DSS
tp
EAS, Single Pulse Avalanche Energy (mJ)
AUIRFR2607Z
400
I D
3.5A
4.8A
BOTTOM 30A
TOP
300
200
100
0
25
50
75
100
125
150
175
Starting TJ, Junction Temperature (°C)
I AS
Fig 12c. Maximum Avalanche Energy
Vs. Drain Current
Fig 12b. Unclamped Inductive Waveforms
QG
QGS
QGD
5.0
VGS(th) Gate threshold Voltage (V)
10 V
VG
Charge
Fig 13a. Basic Gate Charge Waveform
L
DUT
0
1K
ID = 1.0A
ID = 1.0mA
ID = 250µA
ID = 50µA
4.5
4.0
3.5
3.0
2.5
VCC
2.0
-75 -50 -25
0
25
50
75
100 125 150 175
TJ , Temperature ( °C )
Fig 13b. Gate Charge Test Circuit
www.irf.com
Fig 14. Threshold Voltage Vs. Temperature
7
AUIRFR2607Z
1000
Avalanche Current (A)
Duty Cycle = Single Pulse
100
Allowed avalanche Current vs
avalanche pulsewidth, tav
assuming ∆Tj = 25°C due to
avalanche losses. Note: In no
case should Tj be allowed to
exceed Tjmax
0.01
10
0.05
0.10
1
0.1
1.0E-06
1.0E-05
1.0E-04
1.0E-03
1.0E-02
1.0E-01
tav (sec)
Fig 15. Typical Avalanche Current Vs.Pulsewidth
EAR , Avalanche Energy (mJ)
100
TOP
Single Pulse
BOTTOM 1% Duty Cycle
ID = 30A
80
60
40
20
0
25
50
75
100
125
150
Starting TJ , Junction Temperature (°C)
Fig 16. Maximum Avalanche Energy
Vs. Temperature
8
Notes on Repetitive Avalanche Curves , Figures 15, 16:
(For further info, see AN-1005 at www.irf.com)
1. Avalanche failures assumption:
Purely a thermal phenomenon and failure occurs at a
temperature far in excess of T jmax. This is validated for
every part type.
2. Safe operation in Avalanche is allowed as long asTjmax is
not exceeded.
3. Equation below based on circuit and waveforms shown in
Figures 12a, 12b.
4. PD (ave) = Average power dissipation per single
avalanche pulse.
5. BV = Rated breakdown voltage (1.3 factor accounts for
voltage increase during avalanche).
6. Iav = Allowable avalanche current.
7. ∆T = Allowable rise in junction temperature, not to exceed
Tjmax (assumed as 25°C in Figure 15, 16).
tav = Average time in avalanche.
175
D = Duty cycle in avalanche = tav ·f
ZthJC(D, tav ) = Transient thermal resistance, see figure 11)
PD (ave) = 1/2 ( 1.3·BV·Iav) = DT/ ZthJC
Iav = 2DT/ [1.3·BV·Zth]
EAS (AR) = PD (ave)·tav
www.irf.com
AUIRFR2607Z
D.U.T
Driver Gate Drive
ƒ
+
‚
-
-
„
P.W.
Period
*
D.U.T. ISD Waveform
Reverse
Recovery
Current
+
• dv/dt controlled by R G
• Driver same type as D.U.T.
• I SD controlled by Duty Factor "D"
• D.U.T. - Device Under Test
D=
VGS=10V
Circuit Layout Considerations
• Low Stray Inductance
• Ground Plane
• Low Leakage Inductance
Current Transformer

RG
Period
P.W.
+
V DD
+
Body Diode Forward
Current
di/dt
D.U.T. VDS Waveform
Diode Recovery
dv/dt
Re-Applied
Voltage
-
Body Diode
VDD
Forward Drop
Inductor Curent
Ripple ≤ 5%
ISD
* VGS = 5V for Logic Level Devices
Fig 17. Peak Diode Recovery dv/dt Test Circuit for N-Channel
HEXFET® Power MOSFETs
V DS
V GS
RG
RD
D.U.T.
+
-V DD
10V
Pulse Width ≤ 1 µs
Duty Factor ≤ 0.1 %
Fig 18a. Switching Time Test Circuit
VDS
90%
10%
VGS
td(on)
tr
t d(off)
tf
Fig 18b. Switching Time Waveforms
www.irf.com
9
AUIRFR2607Z
D-Pak (TO-252AA) Package Outline
Dimensions are shown in millimeters (inches)
D-Pak (TO-252AA) Part Marking Information
Part Number
AUFR2607Z
YWWA
IR Logo
XX
or
Date Code
Y= Year
WW= Work Week
A= Automotive, Lead Free
XX
Lot Code
Note: For the most current drawing please refer to IR website at http://www.irf.com/package/
10
www.irf.com
AUIRFR2607Z
D-Pak (TO-252AA) Tape & Reel Information
Dimensions are shown in millimeters (inches)
TR
TRR
16.3 ( .641 )
15.7 ( .619 )
12.1 ( .476 )
11.9 ( .469 )
FEED DIRECTION
TRL
16.3 ( .641 )
15.7 ( .619 )
8.1 ( .318 )
7.9 ( .312 )
FEED DIRECTION
NOTES :
1. CONTROLLING DIMENSION : MILLIMETER.
2. ALL DIMENSIONS ARE SHOWN IN MILLIMETERS ( INCHES ).
3. OUTLINE CONFORMS TO EIA-481 & EIA-541.
13 INCH
16 mm
NOTES :
1. OUTLINE CONFORMS TO EIA-481.
www.irf.com
11
AUIRFR2607Z
Ordering Information
Base part
AUIRFR2607Z
12
Package Type
DPak
Standard Pack
Form
Tube
Tape and Reel
Tape and Reel Left
Tape and Reel Right
Quantity
75
2000
3000
3000
Complete Part Number
AUIRFR2607Z
AUIRFR2607ZTR
AUIRF2607ZTRL
AUIRF2607ZTRR
www.irf.com
AUIRFR2607Z
IMPORTANT NOTICE
Unless specifically designated for the automotive market, International Rectifier Corporation and its subsidiaries (IR) reserve
the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services
at any time and to discontinue any product or services without notice. Part numbers designated with the “AU” prefix follow
automotive industry and / or customer specific requirements with regards to product discontinuance and process change
notification. All products are sold subject to IR’s terms and conditions of sale supplied at the time of order acknowledgment.
IR warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with IR’s
standard warranty. Testing and other quality control techniques are used to the extent IR deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
IR assumes no liability for applications assistance or customer product design. Customers are responsible for their products
and applications using IR components. To minimize the risks with customer products and applications, customers should
provide adequate design and operating safeguards.
Reproduction of IR information in IR data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alterations
is an unfair and deceptive business practice. IR is not responsible or liable for such altered documentation. Information of
third parties may be subject to additional restrictions.
Resale of IR products or serviced with statements different from or beyond the parameters stated by IR for that product or
service voids all express and any implied warranties for the associated IR product or service and is an unfair and deceptive
business practice. IR is not responsible or liable for any such statements.
IR products are not designed, intended, or authorized for use as components in systems intended for surgical implant into
the body, or in other applications intended to support or sustain life, or in any other application in which the failure of the IR product
could create a situation where personal injury or death may occur. Should Buyer purchase or use IR products for any such
unintended or unauthorized application, Buyer shall indemnify and hold International Rectifier and its officers, employees,
subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney
fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized
use, even if such claim alleges that IR was negligent regarding the design or manufacture of the product.
IR products are neither designed nor intended for use in military/aerospace applications or environments unless the IR products
are specifically designated by IR as military-grade or “enhanced plastic.” Only products designated by IR as military-grade
meet military specifications. Buyers acknowledge and agree that any such use of IR products which IR has not designated
as military-grade is solely at the Buyer’s risk, and that they are solely responsible for compliance with all legal and regulatory
requirements in connection with such use.
IR products are neither designed nor intended for use in automotive applications or environments unless the specific IR products
are designated by IR as compliant with ISO/TS 16949 requirements and bear a part number including the designation “AU”.
Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, IR will not be
responsible for any failure to meet such requirements
For technical support, please contact IR’s Technical Assistance Center
http://www.irf.com/technical-info/
WORLD HEADQUARTERS:
233 Kansas St., El Segundo, California 90245
Tel: (310) 252-7105
www.irf.com
13