PCA9506 40-bit I2C-bus I/O port with RESET, OE, and INT Rev. 01 — 14 February 2006 Product data sheet 1. General description The PCA9506 provides 40-bit parallel input/output (I/O) port expansion for I2C-bus applications organized in 5 banks of 8 I/Os. At 5 V supply voltage, the outputs are capable of sourcing 10 mA and sinking 25 mA with a total package load of 800 mA to allow direct driving of 40 LEDs. Any of the 40 I/O ports can be configured as an input or output. Output ports are totem-pole and their logic state changes at the Acknowledge (bank change). The device can be configured to have each input port to be masked in order to prevent it from generating interrupts when its state changes and to have the I/O data logic state to be inverted when read by the system master. An open-drain interrupt (INT) output pin allows monitoring of the input pins and is asserted each time a change occurs in one or several input ports (unless masked). The Output Enable (OE) pin 3-states any I/O selected as output and can be used as an input signal to blink or dim LEDs (PWM with frequency > 80 Hz and change duty cycle). The internal Power-On Reset (POR) or hardware reset (RESET) pin initializes the 40 I/Os as inputs. Three address select pins configure one of 8 slave addresses. The PCA9506 is available in 56-pin TSSOP and HVQFN packages and is specified over the −40 °C to +85 °C industrial temperature range. 2. Features ■ Standard mode (100 kHz) and Fast mode (400 kHz) compatible I2C-bus serial interface ■ 2.3 V to 5.5 V operation with 5.5 V tolerant I/Os ■ 40 configurable I/O pins that default to inputs at power-up ■ Outputs: ◆ Totem-pole (10 mA source, 25 mA sink) with controlled edge rate output structure ◆ Active LOW output enable (OE) input pin 3-states all outputs ◆ Output state change on Acknowledge ■ Inputs: ◆ Open-drain active LOW interrupt (INT) output pin allows monitoring of logic level change of pins programmed as inputs ◆ Programmable Interrupt Mask Control for input pins that do not require an interrupt when their states change ◆ Polarity Inversion register allows inversion of the polarity of the I/O pins when read ■ Active LOW reset (RESET) input pin resets device to power-up default state ■ 3 programmable address pins allowing 8 devices on the same bus PCA9506 Philips Semiconductors 40-bit I2C-bus I/O port with RESET, OE, and INT ■ Designed for live insertion ◆ Minimize line disturbance (IOFF and power-up 3-state) ◆ Signal transient rejection (50 ns noise filter and robust I2C-bus state machine) ■ Low standby current ■ −40 °C to +85 °C operation ■ ESD protection exceeds 2000 V HBM per JESD22-A114, 200 V MM per JESD22-A115, and 1000 V CDM per JESD22-C101 ■ Latch-up testing is done to JEDEC Standard JESD78, which exceeds 100 mA ■ Offered in TSSOP56 and HVQFN56 packages 3. Applications ■ ■ ■ ■ ■ ■ ■ ■ Servers RAID systems Industrial control Medical equipment PLCs Cell phones Gaming machines Instrumentation and test measurement 4. Ordering information Table 1: Ordering information Type number Topside mark Package Name Description Version PCA9506DGG PCA9506DGG TSSOP56 plastic thin shrink small outline package; 56 leads; body width 6.1 mm SOT364-1 PCA9506BS PCA9506BS HVQFN56 plastic thermal enhanced very thin quad flat package; no leads; 56 terminals; body 8 × 8 × 0.85 mm SOT684-1 9397 750 14939 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 01 — 14 February 2006 2 of 30 PCA9506 Philips Semiconductors 40-bit I2C-bus I/O port with RESET, OE, and INT 5. Block diagram OE PCA9506 8-bit A0 A1 write pulse 0 A2 read pulse 0 INPUT/ OUTPUT PORTS BANK 0 IO0_0 IO0_1 IO0_2 IO0_3 IO0_4 IO0_5 IO0_6 IO0_7 BANK 1 SCL SDA LOW PASS INPUT FILTERS I2C-BUS CONTROL BANK 2 BANK 3 8-bit write pulse 4 VDD VSS POWER-ON RESET read pulse 4 INPUT/ OUTPUT PORTS BANK 4 IO4_0 IO4_1 IO4_2 IO4_3 IO4_4 IO4_5 IO4_6 IO4_7 RESET INTERRUPT MANAGEMENT INT LP FILTER 002aab492 All I/Os are set to inputs at power-up and RESET. Fig 1. Block diagram of PCA9506 9397 750 14939 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 01 — 14 February 2006 3 of 30 PCA9506 Philips Semiconductors 40-bit I2C-bus I/O port with RESET, OE, and INT configuration port register data (Cx[y]) I/O configuration register data from shift register D output port register data (Ox[y]) Q VDD write configuration pulse CK Q IOx_y data from shift register D ESD protection diode Q VSS write pulse CK Mx[y] output port register input port register D read pulse Q INTERRUPT MANAGEMENT INT input port register data (Ix[y]) CK polarity inversion register data from shift register D write polarity pulse CK Q polarity register data (Px[y]) 002aab493 On power-up or RESET, all registers return to default values. Fig 2. Simplified schematic of IO0_0 to IO4_7 9397 750 14939 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 01 — 14 February 2006 4 of 30 PCA9506 Philips Semiconductors 40-bit I2C-bus I/O port with RESET, OE, and INT 6. Pinning information 6.1 Pinning SDA 1 56 RESET SCL 2 55 INT IO0_0 3 54 IO4_7 IO0_1 4 53 IO4_6 IO0_2 5 52 IO4_5 VSS 6 IO0_3 7 51 VSS 50 IO4_4 IO0_4 8 49 IO4_3 IO0_5 9 48 IO4_2 IO0_6 10 47 IO4_1 VSS 11 IO0_7 12 46 VDD 45 IO4_0 IO1_0 13 44 IO3_7 IO1_1 14 IO1_2 15 43 IO3_6 PCA9506DGG 42 IO3_5 IO1_3 16 41 IO3_4 IO1_4 17 40 IO3_3 VDD 18 IO1_5 19 39 VSS 38 IO3_2 IO1_6 20 37 IO3_1 IO1_7 21 36 IO3_0 IO2_0 22 35 IO2_7 VSS 23 IO2_1 24 34 VSS 33 IO2_6 IO2_2 25 32 IO2_5 IO2_3 26 31 IO2_4 A0 27 30 OE A1 28 29 A2 002aab491 Fig 3. Pin configuration for TSSOP56 9397 750 14939 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 01 — 14 February 2006 5 of 30 PCA9506 Philips Semiconductors 43 IO4_4 44 VSS 45 IO4_5 46 IO4_6 47 IO4_7 48 INT 49 RESET 50 SDA 51 SCL 52 IO0_0 53 IO0_1 54 IO0_2 terminal 1 index area 55 VSS 56 IO0_3 40-bit I2C-bus I/O port with RESET, OE, and INT IO0_4 1 42 IO4_3 IO0_5 2 41 IO4_2 IO0_6 3 40 IO4_1 VSS 4 39 VDD IO0_7 5 38 IO4_0 IO1_0 6 37 IO3_7 IO1_1 7 IO1_2 8 IO1_3 9 34 IO3_4 IO1_4 10 33 IO3_3 36 IO3_6 PCA9506BS 35 IO3_5 VDD 11 32 VSS IO2_7 28 VSS 27 IO2_6 26 IO2_5 25 IO2_4 24 OE 23 A2 22 A1 21 A0 20 IO2_3 19 IO2_2 18 29 IO3_0 IO2_1 17 30 IO3_1 IO1_7 14 VSS 16 31 IO3_2 IO1_6 13 IO2_0 15 IO1_5 12 002aab975 Transparent top view Fig 4. Pin configuration for HVQFN56 6.2 Pin description Table 2: Pin description Symbol Pin Type Description TSSOP56 HVQFN56 SDA 1 50 I/O serial data line SCL 2 51 I serial clock line IO0_0 to IO0_7 3, 4, 5, 7, 8, 9, 10, 12 52, 53, 54, 56, 1, I/O 2, 3, 5 input/output bank 0 IO1_0 to IO1_7 13, 14, 15, 16, 17, 19, 20, 21 6, 7, 8, 9, 10, 12, I/O 13, 14 input/output bank 1 IO2_0 to IO2_7 22, 24, 25, 26, 31, 32, 33, 35 15, 17, 18, 19, 24, 25, 26, 28 I/O input/output bank 2 IO3_0 to IO3_7 36, 37, 38, 40, 41, 42, 43, 44 29, 30, 31, 33, 34, 35, 36, 37 I/O input/output bank 3 IO4_0 to IO4_7 45, 47, 48, 49, 50, 52, 53, 54 38, 40, 41, 42, 43, 45, 46, 47 I/O input/output bank 4 VSS 6, 11, 23, 34, 39, 51 4, 16, 27, 32, 44, power 55 [1] supply ground supply voltage VDD 18, 46 11, 39 power supply supply voltage A0 27 20 I address input 0 A1 28 21 I address input 1 A2 29 22 I address input 2 9397 750 14939 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 01 — 14 February 2006 6 of 30 PCA9506 Philips Semiconductors 40-bit I2C-bus I/O port with RESET, OE, and INT Table 2: Pin description …continued Symbol Pin Type Description 23 I active LOW output enable input 55 48 O active LOW interrupt output 56 49 I active LOW reset input TSSOP56 HVQFN56 OE 30 INT RESET [1] HVQFN package die supply ground is connected to both VSS pins and exposed center pad. VSS pins must be connected to supply ground for proper device operation. For enhanced thermal, electrical, and board level performance, the exposed pad needs to be soldered to the board using a corresponding thermal pad on the board and for proper heat conduction through the board, thermal vias need to be incorporated in the printed-circuit board in the thermal pad region. 7. Functional description Refer to Figure 1 “Block diagram of PCA9506” and Figure 2 “Simplified schematic of IO0_0 to IO4_7”. 7.1 Device address Following a START condition, the bus master must send the address of the slave it is accessing and the operation it wants to perform (read or write). The address of the PCA9506 is shown in Figure 5. Slave address pins A2, A1, and A0 choose 1 of 8 slave addresses and need to be connected to VDD (1) or VSS (0). To conserve power, no internal pull-up resistors are incorporated on A2, A1, and A0. slave address 0 1 0 0 fixed A2 A1 A0 R/W programmable 002aab494 Fig 5. PCA9506 address The last bit of the first byte defines the operation to be performed. When set to logic 1 a read is selected, while a logic 0 selects a write operation. 7.2 Command register Following the successful acknowledgement of the slave address + R/W bit, the bus master will send a byte to the PCA9506, which will be stored in the Command register. AI − D5 D4 D3 D2 D1 D0 1 0 0 0 0 0 0 0 default at power-up or after RESET register number Auto-Increment 002aab495 Fig 6. Command register 9397 750 14939 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 01 — 14 February 2006 7 of 30 PCA9506 Philips Semiconductors 40-bit I2C-bus I/O port with RESET, OE, and INT The lowest 6 bits are used as a pointer to determine which register will be accessed. The registers are: • • • • • IP: Input Port registers (5 registers) OP: Output Port registers (5 registers) PI: Polarity Inversion registers (5 registers) IOC: I/O Configuration registers (5 registers) MSK: Mask interrupt registers (5 registers) If the Auto-Increment flag is set (AI = 1), the 3 least significant bits are automatically incremented after a read or write. This allows the user to program and/or read the 5 register banks sequentially. If more than 5 bytes of data are written and AI = 1, previous data in the selected registers will be overwritten. Reserved registers are skipped and not accessed (refer to Table 3). If the Auto-Increment flag is cleared (AI = 0), the 3 least significant bits are not incremented after data is read or written. During a read operation, the same register bank is read each time. During a write operation, data is written to the same register bank each time. Only a Command register code with the 5 least significant bits equal to the 25 allowable values as defined in Table 3 are valid. Reserved or undefined command codes must not be accessed for proper device functionality. At power-up, this register defaults to 0x80, with the AI bit set to logic 1, and the lowest 7 bits set to logic 0. During a write operation, the PCA9506 will acknowledge a byte sent to OPx, PIx, and IOCx and MSKx registers, but will not acknowledge a byte sent to the IPx registers since these are read-only registers. 9397 750 14939 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 01 — 14 February 2006 8 of 30 PCA9506 Philips Semiconductors 40-bit I2C-bus I/O port with RESET, OE, and INT 7.3 Register definitions Table 3: Register # (hex) Register summary D5 D4 D3 D2 D1 D0 Symbol Access Description Input Port registers 00 0 0 0 0 0 0 IP0 read only Input Port register bank 0 01 0 0 0 0 0 1 IP1 read only Input Port register bank 1 02 0 0 0 0 1 0 IP2 read only Input Port register bank 2 03 0 0 0 0 1 1 IP3 read only Input Port register bank 3 04 0 0 0 1 0 0 IP4 read only Input Port register bank 4 05 0 0 0 1 0 1 - - reserved for future use 06 0 0 0 1 1 0 - - reserved for future use 07 0 0 0 1 1 1 - - reserved for future use Output Port registers 08 0 0 1 0 0 0 OP0 read/write Output Port register bank 0 09 0 0 1 0 0 1 OP1 read/write Output Port register bank 1 0A 0 0 1 0 1 0 OP2 read/write Output Port register bank 2 0B 0 0 1 0 1 1 OP3 read/write Output Port register bank 3 0C 0 0 1 1 0 0 OP4 read/write Output Port register bank 4 0D 0 0 1 1 0 1 - - reserved for future use 0E 0 0 1 1 1 0 - - reserved for future use 0F 0 0 1 1 1 1 - - reserved for future use Polarity Inversion registers 10 0 1 0 0 0 0 PI0 read/write Polarity Inversion register bank 0 11 0 1 0 0 0 1 PI1 read/write Polarity Inversion register bank 1 12 0 1 0 0 1 0 PI2 read/write Polarity Inversion register bank 2 13 0 1 0 0 1 1 PI3 read/write Polarity Inversion register bank 3 14 0 1 0 1 0 0 PI4 read/write Polarity Inversion register bank 4 15 0 1 0 1 0 1 - - reserved for future use 16 0 1 0 1 1 0 - - reserved for future use 17 0 1 0 1 1 1 - - reserved for future use I/O Configuration registers 18 0 1 1 0 0 0 IOC0 read/write I/O Configuration register bank 0 19 0 1 1 0 0 1 IOC1 read/write I/O Configuration register bank 1 1A 0 1 1 0 1 0 IOC2 read/write I/O Configuration register bank 2 1B 0 1 1 0 1 1 IOC3 read/write I/O Configuration register bank 3 1C 0 1 1 1 0 0 IOC4 read/write I/O Configuration register bank 4 1D 0 1 1 1 0 1 - - reserved for future use 1E 0 1 1 1 1 0 - - reserved for future use 1F 0 1 1 1 1 1 - - reserved for future use 9397 750 14939 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 01 — 14 February 2006 9 of 30 PCA9506 Philips Semiconductors 40-bit I2C-bus I/O port with RESET, OE, and INT Table 3: Register # (hex) Register summary …continued D5 D4 D3 D2 D1 D0 Symbol Access Description Mask Interrupt registers 20 1 0 0 0 0 0 MSK0 read/write Mask Interrupt register bank 0 21 1 0 0 0 0 1 MSK1 read/write Mask Interrupt register bank 1 22 1 0 0 0 1 0 MSK2 read/write Mask Interrupt register bank 2 23 1 0 0 0 1 1 MSK3 read/write Mask Interrupt register bank 3 24 1 0 0 1 0 0 MSK4 read/write Mask Interrupt register bank 4 25 1 0 0 1 0 1 - - reserved for future use 26 1 0 0 1 1 0 - - reserved for future use 27 1 0 0 1 1 1 - - reserved for future use 7.3.1 IP0 to IP4 - Input Port registers These registers are read-only. They reflect the incoming logic levels of the port pins regardless of whether the pin is defined as an input or an output by the I/O Configuration register. If the corresponding Px[y] bit in the PI registers is set to logic 0, or the inverted incoming logic levels if the corresponding Px[y] bit in the PI register is set to logic 1. Writes to these registers have no effect. Table 4: IP0 to IP4 - Input Port registers (address 00h to 04h) bit description Legend: * default value ‘X’ determined by the externally applied logic level. Address Register Bit Symbol Access Value Description 00h IP0 7 to 0 I0[7:0] R XXXX XXXX* Input Port register bank 0 01h IP1 7 to 0 I1[7:0] R XXXX XXXX* Input Port register bank 1 02h IP2 7 to 0 I2[7:0] R XXXX XXXX* Input Port register bank 2 03h IP3 7 to 0 I3[7:0] R XXXX XXXX* Input Port register bank 3 04h IP4 7 to 0 I4[7:0] R XXXX XXXX* Input Port register bank 4 The Polarity Inversion register can invert the logic states of the port pins. The polarity of the corresponding bit is inverted when Px[y] bit in the PI register is set to logic 1. The polarity of the corresponding bit is not inverted when Px[y] bits in the PI register is set to logic 0. 9397 750 14939 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 01 — 14 February 2006 10 of 30 PCA9506 Philips Semiconductors 40-bit I2C-bus I/O port with RESET, OE, and INT 7.3.2 OP0 to OP4 - Output Port registers These registers reflect the outgoing logic levels of the pins defined as outputs by the I/O Configuration register. Bit values in these registers have no effect on pins defined as inputs. In turn, reads from these registers reflect the values that are in the flip-flops controlling the output selection, not the actual pin values. Ox[y] = 0: IOx_y = 0 if IOx_y defined as output (Cx[y] in IOC register = 0). Ox[y] = 1: IOx_y = 1 if IOx_y defined as output (Cx[y] in IOC register = 0). Where ‘x’ refers to the bank number (0 to 4); ‘y’ refers to the bit number (0 to 7). Table 5: OP0 to OP4 - Output Port registers (address 08h to 0Ch) bit description Legend: * default value. Address Register Bit Symbol Access Value Description 08h OP0 7 to 0 O0[7:0] R/W 0000 0000* Output Port register bank 0 09h OP1 7 to 0 O1[7:0] R/W 0000 0000* Output Port register bank 1 0Ah OP2 7 to 0 O2[7:0] R/W 0000 0000* Output Port register bank 2 0Bh OP3 7 to 0 O3[7:0] R/W 0000 0000* Output Port register bank 3 0Ch OP4 7 to 0 O4[7:0] R/W 0000 0000* Output Port register bank 4 7.3.3 PI0 to PI4 - Polarity Inversion registers These registers allow inversion of the polarity of the corresponding Input Port register. Px[y] = 0: The corresponding Input Port register data polarity is retained. Px[y] = 1: The corresponding Input Port register data polarity is inverted. Where ‘x’ refers to the bank number (0 to 4); ‘y’ refers to the bit number (0 to 7). Table 6: PI0 to PI4 - Polarity Inversion registers (address 10h to 14h) bit description Legend: * default value. Address Register Bit Symbol Access Value Description 10h PI0 7 to 0 P0[7:0] R/W 0000 0000* Polarity Inversion register bank 0 11h PI1 7 to 0 P1[7:0] R/W 0000 0000* Polarity Inversion register bank 1 12h PI2 7 to 0 P2[7:0] R/W 0000 0000* Polarity Inversion register bank 2 13h PI3 7 to 0 P3[7:0] R/W 0000 0000* Polarity Inversion register bank 3 14h PI4 7 to 0 P4[7:0] R/W 0000 0000* Polarity Inversion register bank 4 9397 750 14939 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 01 — 14 February 2006 11 of 30 PCA9506 Philips Semiconductors 40-bit I2C-bus I/O port with RESET, OE, and INT 7.3.4 IOC0 to IOC4 - I/O Configuration registers These registers configure the direction of the I/O pins. Cx[y] = 0: The corresponding port pin is an output. Cx[y] = 1: The corresponding port pin is an input. Where ‘x’ refers to the bank number (0 to 4); ‘y’ refers to the bit number (0 to 7). Table 7: IOC0 to IOC4 - I/O Configuration registers (address 18h to 1Ch) bit description Legend: * default value. Address Register Bit Symbol Access Value Description 18h IOC0 7 to 0 C0[7:0] R/W 1111 1111* I/O Configuration register bank 0 19h IOC1 7 to 0 C1[7:0] R/W 1111 1111* I/O Configuration register bank 1 1Ah IOC2 7 to 0 C2[7:0] R/W 1111 1111* I/O Configuration register bank 2 1Bh IOC3 7 to 0 C3[7:0] R/W 1111 1111* I/O Configuration register bank 3 1Ch IOC4 7 to 0 C4[7:0] R/W 1111 1111* I/O Configuration register bank 4 7.3.5 MSK0 to MSK4 - Mask interrupt registers These registers mask the interrupt due to a change in the I/O pins configured as inputs. ‘x’ refers to the bank number (0 to 4); ‘y’ refers to the bit number (0 to 7). Mx[y] = 0: A level change at the I/O will generate an interrupt if IOx_y defined as input (Cx[y] in IOC register = 1). Mx[y] = 1: A level change in the input port will not generate an interrupt if IOx_y defined as input (Cx[y] in IOC register = 1). Table 8: MSK0 to MSK4 - Mask interrupt registers (address 20h to 24h) bit description Legend: * default value. Address Register Bit Symbol Access Value Description 20h MSK0 7 to 0 M0[7:0] R/W 1111 1111* Mask Interrupt register bank 0 21h MSK1 7 to 0 M1[7:0] R/W 1111 1111* Mask Interrupt register bank 1 22h MSK2 7 to 0 M2[7:0] R/W 1111 1111* Mask Interrupt register bank 2 23h MSK3 7 to 0 M3[7:0] R/W 1111 1111* Mask Interrupt register bank 3 24h MSK4 7 to 0 M4[7:0] R/W 1111 1111* Mask Interrupt register bank 4 7.4 Power-on reset When power is applied to VDD, an internal Power-On Reset (POR) holds the PCA9506 in a reset condition until VDD has reached VPOR. At that point, the reset condition is released and the PCA9506 registers and I2C-bus state machine will initialize to their default states. Thereafter, VDD must be lowered below 0.2 V to reset the device. 7.5 RESET input A reset can be accomplished by holding the RESET pin LOW for a minimum of tw(rst). The PCA9506 registers and I2C-bus state machine will be held in their default states until the RESET input is once again HIGH. 9397 750 14939 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 01 — 14 February 2006 12 of 30 PCA9506 Philips Semiconductors 40-bit I2C-bus I/O port with RESET, OE, and INT 7.6 Interrupt output (INT) The open-drain active LOW interrupt is activated when one of the port pins changes state and the port pin is configured as an input and the interrupt on it is not masked. The interrupt is deactivated when the port pin input returns to its previous state or the Input Port register is read. Remark: Changing an I/O from an output to an input may cause a false interrupt to occur if the state of the pin does not match the contents of the Input Port register. Only a Read of the Input Port register that contains the bit(s) image of the input(s) that generated the interrupt clears the interrupt condition. If more than one input register changed state before a read of the Input Port register is initiated, the interrupt is cleared when all the input registers containing all the inputs that changed are read. Example: If IO0_5, IO2_3, and IO3_7 change state at the same time, the interrupt is cleared only when INREG0, INREG2, and INREG3 are read. 7.7 Output enable input (OE) The active LOW output enable pin allows to enable or disable all the I/Os at the same time. When a LOW level is applied to the OE pin, all the I/Os configured as outputs are enabled and the logic value programmed in their respective OP registers is applied to the pins. When a HIGH level is applied to the OE pin, all the I/Os configured as outputs are 3-stated. For applications requiring LED blinking with brightness control, this pin can be used to control the brightness by applying a high frequency PWM signal on the OE pin. LEDs can be blinked using the Output Port registers and can be dimmed using the PWM signal on the OE pin thus controlling the brightness by adjusting the duty cycle. 7.8 Live insertion The PCA9506 is fully specified for live insertion applications using IOFF, power-up 3-states, robust state machine, and 50 ns noise filter. The IOFF circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. The power-up 3-state’s circuitry places the outputs in the high-impedance state during power-up and power-down, which prevents driver conflict and bus contention. The robust state machine does not respond until it sees a valid START condition and the 50 ns noise filter will filter out any insertion glitches. The PCA9506 will not cause corruption of active data on the bus, nor will the device be damaged or cause damage to devices already on the bus when similar featured devices are being used. 7.9 Standby The PCA9506 goes into standby when the I2C-bus is idle. Standby supply current is lower than 1 µA (typical). 9397 750 14939 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 01 — 14 February 2006 13 of 30 PCA9506 Philips Semiconductors 40-bit I2C-bus I/O port with RESET, OE, and INT 8. Characteristics of the I2C-bus The I2C-bus is for 2-way, 2-line communication between different ICs or modules. The two lines are a serial data line (SDA) and a serial clock line (SCL). Both lines must be connected to a positive supply via a pull-up resistor when connected to the output stages of a device. Data transfer may be initiated only when the bus is not busy. 8.1 Bit transfer One data bit is transferred during each clock pulse. The data on the SDA line must remain stable during the HIGH period of the clock pulse as changes in the data line at this time will be interpreted as control signals (see Figure 7). SDA SCL data line stable; data valid change of data allowed mba607 Fig 7. Bit transfer 8.1.1 START and STOP conditions Both data and clock lines remain HIGH when the bus is not busy. A HIGH-to-LOW transition of the data line while the clock is HIGH is defined as the START condition (S). A LOW-to-HIGH transition of the data line while the clock is HIGH is defined as the STOP condition (P) (see Figure 8). SDA SDA SCL SCL S P START condition STOP condition mba608 Fig 8. Definition of START and STOP conditions 8.2 System configuration A device generating a message is a ‘transmitter’; a device receiving is the ‘receiver’. The device that controls the message is the ‘master' and the devices which are controlled by the master are the ‘slaves' (see Figure 9). 9397 750 14939 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 01 — 14 February 2006 14 of 30 PCA9506 Philips Semiconductors 40-bit I2C-bus I/O port with RESET, OE, and INT SDA SCL MASTER TRANSMITTER/ RECEIVER SLAVE TRANSMITTER/ RECEIVER SLAVE RECEIVER MASTER TRANSMITTER MASTER TRANSMITTER/ RECEIVER I2C-BUS MULTIPLEXER SLAVE 002aaa966 Fig 9. System configuration 8.3 Acknowledge The number of data bytes transferred between the START and the STOP conditions from transmitter to receiver is not limited. Each byte of eight bits is followed by one acknowledge bit. The acknowledge bit is a HIGH level put on the bus by the transmitter, whereas the master generates an extra acknowledge related clock pulse. A slave receiver which is addressed must generate an acknowledge after the reception of each byte. Also a master must generate an acknowledge after the reception of each byte that has been clocked out of the slave transmitter. The device that acknowledges has to pull down the SDA line during the acknowledge clock pulse, so that the SDA line is stable LOW during the HIGH period of the acknowledge related clock pulse; set-up and hold times must be taken into account. A master receiver must signal an end of data to the transmitter by not generating an acknowledge on the last byte that has been clocked out of the slave. In this event, the transmitter must leave the data line HIGH to enable the master to generate a STOP condition. data output by transmitter not acknowledge data output by receiver acknowledge SCL from master 1 S START condition 2 8 9 clock pulse for acknowledgement 002aaa987 Fig 10. Acknowledgement on the I2C-bus 8.4 Bus transactions Data is transmitted to the PCA9506 registers using Write Byte transfers (see Figure 11, Figure 12, and Figure 13). Data is read from the PCA9506 registers using Read and Receive Byte transfers (see Figure 14). 9397 750 14939 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 01 — 14 February 2006 15 of 30 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Philips Semiconductors 9397 750 14939 Product data sheet STOP condition slave address command register SDA S 0 1 0 0 A2 A1 A0 0 A 1 0 0 0 1 0 0 0 A START condition R/W AI = 1 acknowledge from slave DATA BANK 0 output bank register bank 0 is selected A DATA BANK 1 acknowledge from slave A DATA BANK 2 A DATA BANK 3 A DATA BANK 4 A P acknowledge from slave acknowledge from slave acknowledge from slave acknowledge from slave data valid bank 0 data valid bank 1 data valid bank 2 data valid bank 3 acknowledge from slave write to port data out from port data valid bank 4 002aab496 tv(Q) Rev. 01 — 14 February 2006 OE is LOW to observe a change in the outputs. If more than 5 bytes are written, previous data are overwritten. Fig 11. Write to the 5 output ports SDA S 0 1 0 0 A2 A1 A0 0 A AI 0 0 0 1 D2 D1 D0 A START condition R/W acknowledge from slave acknowledge from slave DATA BANK X A P acknowledge STOP from slave condition data X valid data out from port tv(Q) 002aab497 OE is LOW to observe a change in the outputs. Two, three, or four adjacent banks can be programmed by using the Auto-Increment feature (AI = 1) and change at the corresponding output port becomes effective at each acknowledge. Fig 12. Write to a specific output port PCA9506 16 of 30 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. write to port 40-bit I2C-bus I/O port with RESET, OE, and INT slave address xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx command register SDA S 0 1 0 0 A2 A1 A0 0 A 1 0 D5 D4 D3 D2 D1 D0 A START condition Philips Semiconductors 9397 750 14939 Product data sheet slave address R/W DATA BANK 0 acknowledge from slave AI = 1 acknowledge from slave A DATA BANK 1 acknowledge from slave A DATA BANK 2 acknowledge from slave D[5:0] = 01 0000 for Polarity Inversion register programming bank 0 D[5:0] = 01 1000 for Configuration register programming bank 0 D[5:0] = 10 0000 for Mask Interrupt register programming bank 0 A DATA BANK 3 A acknowledge from slave acknowledge from slave DATA BANK 4 A P acknowledge from slave STOP condition 002aab498 The programming becomes effective at the acknowledge. Less than 5 bytes can be programmed by using this scheme. D5, D4, D3, D2, D1, D0 refers to the first register to be programmed. If more than 5 bytes are written, previous data are overwritten (the sixth Configuration register will roll over to the first addressed Configuration register, the sixth Polarity Inversion register will roll over to the first addressed Polarity Inversion register and the sixth Mask Interrupt register will roll over to the first addressed Mask Interrupt register). Fig 13. Write to the I/O Configuration, Polarity Inversion or Mask Interrupt registers repeated START condition slave address command register At this moment master-transmitter becomes master-receiver, and slave-receiver becomes slave-transmitter. SDA S 0 1 0 0 A2 A1 A0 0 A 1 0 D5 D4 D3 D2 D1 D0 A Sr 0 1 0 0 A2 A1 A0 1 A START condition R/W acknowledge from slave AI = 1 first byte register determined by D[5:0] acknowledge from master data from register A DATA second byte no acknowledge from master acknowledge from master data from register A DATA last byte A P STOP condition 002aab499 If AI = 0, the same register is read during the whole sequence. If AI = 1, the register value is incremented after each read. When the last register bank is read, it rolls over to the first byte of the category (see category definition in Section 7.2 “Command register”). The INT signal is released only when the last register containing an input that changed has been read. For example, when IO2_4 and IO4_7 change at the same time and an Input Port register’s read sequence is initiated, starting with IP0, INT is released after IP4 is read (and not after IP2 is read). Fig 14. Read from Input Port, Output Port, I/O Configuration, Polarity Inversion or Mask Interrupt registers PCA9506 17 of 30 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. DATA R/W acknowledge from slave D[5:0] = 00 0000 for Input Port register bank 0 D[5:0] = 00 1000 for Output Port register bank 0 D[5:0] = 01 0000 for Polarity Inversion register bank 0 D[5:0] = 01 1000 for Configuration register bank 0 D[5:0] = 10 0000 for Mask Interrupt register bank 0 acknowledge from slave data from register (cont.) 40-bit I2C-bus I/O port with RESET, OE, and INT Rev. 01 — 14 February 2006 slave address PCA9506 Philips Semiconductors 40-bit I2C-bus I/O port with RESET, OE, and INT 9. Application design-in information 5V VDD 1.6 kΩ VDD 1.6 kΩ 2 kΩ 1.1 kΩ (optional) 1.1 kΩ (optional) SUB-SYSTEM 1 (e.g., temp sensor) VDD INT MASTER CONTROLLER SCL SCL IO0_0 SDA SDA IO0_1 RESET INT OE PCA9506 SUB-SYSTEM 2 (e.g., counter) RESET IO0_2 INT RESET IO0_3 OE GND IO0_4 A controlled switch (e.g., CBT device) ENABLE IO0_5 B IO1_0 SUB-SYSTEM 3 (e.g., alarm system) IO3_7 ALARM A2 IO4_0 A1 A0 VDD IO4_7 VSS ALPHA NUMERIC KEYPAD 24 LED MATRIX 002aab500 Device address configured as 0100 000X for this example. IO0_0, IO0_2, IO0_3, IO1_0 to IO3_7 are configured as outputs. IO0_1, IO0_4, IO4_0 to IO4_7 configured as inputs. Fig 15. Typical application 9397 750 14939 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 01 — 14 February 2006 18 of 30 PCA9506 Philips Semiconductors 40-bit I2C-bus I/O port with RESET, OE, and INT 10. Limiting values Table 9: Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter VDD Conditions Min Max Unit supply voltage −0.5 +6 V VI input voltage VSS − 0.5 5.5 V II input current - ±20 mA VI/O(n) input/output voltage on any other pin VSS − 0.5 5.5 V VI/O(IO0n) input/output voltage on pin IO0_n VSS − 0.5 5.5 V IO(I/On) output current on an I/O pin −20 +50 mA IDD supply current - 500 mA ISS ground supply current - 1100 mA Ptot total power dissipation - 500 mW Tstg storage temperature −65 +150 °C Tamb ambient temperature operating −40 +85 °C Tj junction temperature operating - 125 °C storage - 150 °C 11. Static characteristics Table 10: Static characteristics VDD = 2.3 V to 5.5 V; VSS = 0 V; Tamb = −40 °C to +85 °C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit 2.3 - 5.5 V VDD = 2.3 V - 56 95 µA VDD = 3.3 V - 98 150 µA VDD = 5.5 V - 225 300 µA VDD = 2.3 V - 0.15 11 µA VDD = 3.3 V - 0.25 12 µA VDD = 5.5 V - 0.75 15.5 µA - 1.70 2.0 V −0.5 - +0.3VDD V Supply VDD supply voltage IDD supply current Istb VPOR standby current power-on reset voltage [1] operating mode; no load; fSCL = 400 kHz no load; fSCL = 0 kHz; I/O = inputs; VI = VDD no load; VI = VDD or VSS Input SCL; input/output SDA VIL LOW-level input voltage VIH HIGH-level input voltage 0.7VDD - 5.5 V IOL LOW-level output current VOL = 0.4 V 20 - - mA IL leakage current VI = VDD = VSS −1 - +1 µA Ci input capacitance VI = VSS - 5 10 pF 9397 750 14939 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 01 — 14 February 2006 19 of 30 PCA9506 Philips Semiconductors 40-bit I2C-bus I/O port with RESET, OE, and INT Table 10: Static characteristics …continued VDD = 2.3 V to 5.5 V; VSS = 0 V; Tamb = −40 °C to +85 °C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit −0.5 - +0.8 V 2 - 5.5 V VDD = 2.3 V 10 - - mA VDD = 3.0 V 12 - - mA I/Os VIL LOW-level input voltage VIH HIGH-level input voltage IOL LOW-level output current VOL = 0.5 V VDD = 4.5 V 15 - - mA - - 0.6 A VDD = 2.3 V 1.6 - - V VDD = 3.0 V 2.3 - - V VDD = 4.5 V 4.0 - - V IOL(tot) total LOW-level output current VOL = 0.5 V; VDD = 4.5 V VOH HIGH-level output voltage IOH = −10 mA ILIH HIGH-level input leakage current VDD = 3.6 V; VI = VDD −1 - +1 µA ILIL LOW-level input leakage current VDD = 5.5 V; VI = VSS −1 - +1 µA Ci input capacitance - 6 7 pF Co output capacitance - 6 7 pF 6 - - mA Interrupt INT IOL LOW-level output current VOL = 0.4 V IOH HIGH-level output current −1 - +1 µA Co output capacitance - 3.0 5 pF −0.5 - +0.8 V Inputs RESET and OE VIL LOW-level input voltage VIH HIGH-level input voltage 2 - 5.5 V ILI input leakage current −1 - +1 µA Ci input capacitance - 3.0 5 pF Inputs A0, A1, A2 VIL LOW-level input voltage −0.5 - +0.3VDD V VIH HIGH-level input voltage 0.7VDD - 5.5 V ILI input leakage current −1 - +1 µA Ci input capacitance - 3.5 5 pF [1] VDD must be lowered to 0.2 V in order to reset part. 9397 750 14939 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 01 — 14 February 2006 20 of 30 PCA9506 Philips Semiconductors 40-bit I2C-bus I/O port with RESET, OE, and INT 12. Dynamic characteristics Table 11: Dynamic characteristics Symbol Parameter Conditions Standard mode I2C-bus Min Max [1] Fast mode I2C-bus Min Max Unit fSCL SCL clock frequency 0 100 0 400 tBUF bus free time between a STOP and START condition 4.7 - 1.3 - kHz µs tHD;STA hold time (repeated) START condition 4.0 - 0.6 - µs tSU;STA set-up time for a repeated START condition 4.7 - 0.6 - µs tSU;STO set-up time for STOP condition 4.0 - 0.6 - µs tHD;DAT data hold time tVD;ACK data valid acknowledge time [2] 0 - 0 - ns 0.1 3.45 0.1 0.9 µs tVD;DAT data valid time [3] 0.1 3.45 0.1 0.9 µs tSU;DAT data set-up time 250 - 100 - ns tLOW LOW period of the SCL clock 4.7 - 1.3 - µs tHIGH HIGH period of the SCL clock 4.0 - 0.6 - µs [6] 300 ns tf fall time of both SDA and SCL signals [4] [5] tr rise time of both SDA and SCL signals [4] [5] - 1000 20 + 0.1Cb [6] 300 ns tSP pulse width of spikes that must be suppressed by the input filter [7] - 50 - 50 ns - 300 20 + 0.1Cb Port timing ten enable time output - 80 - 80 ns tdis disable time output - 40 - 40 ns tv(Q) data output valid time - 250 - 250 ns tsu(D) data input setup time 100 - 100 - ns th(D) data input hold time 0.5 - 0.5 - µs Interrupt timing tv(INT_N) valid time on pin INT_N - 4 - 4 µs trst(INT_N) reset time on pin INT_N - 4 - 4 µs tw(rst) reset pulse width 4 - 4 - ns trec(rst) reset recovery time 0 - 0 - ns trst reset time 100 - 100 - ns Reset [1] Minimum SCL clock frequency is limited by the bus time-out feature, which resets the serial bus interface if either SDA or SCL is held LOW for a minimum of 25 ms. Disable bus time-out feature for DC operation. [2] tVD;ACK = time for Acknowledgement signal from SCL LOW to SDA (out) LOW. [3] tVD;DAT = minimum time for SDA data out to be valid following SCL LOW. [4] A master device must internally provide a hold time of at least 300 ns for the SDA signal (refer to the VIL of the SCL signal) in order to bridge the undefined region SCL’s falling edge. 9397 750 14939 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 01 — 14 February 2006 21 of 30 PCA9506 Philips Semiconductors 40-bit I2C-bus I/O port with RESET, OE, and INT [5] The maximum tf for the SDA and SCL bus lines is specified at 300 ns. The maximum fall time for the SDA output stage tf is specified at 250 ns. This allows series protection resistors to be connected between the SDA and the SCL pins and the SDA/SCL bus lines without exceeding the maximum specified tf. [6] Cb = total capacitance of one bus line in pF. [7] Input filters on the SDA and SCL inputs suppress noise spikes less than 50 ns. SDA tr tBUF tf tHD;STA tSP tLOW SCL tHD;STA P tSU;STA tHD;DAT S tHIGH tSU;DAT tSU;STO Sr P 002aaa986 Fig 16. Definition of timing on the I2C-bus protocol START condition (S) tSU;STA bit 7 MSB (A7) tLOW bit 6 (A6) tHIGH bit 0 (R/W) acknowledge (A) STOP condition (P) 1/f SCL SCL tBUF tr tf SDA tHD;STA tSU;DAT tHD;DAT tVD;DAT tVD;ACK tSU;STO 002aab175 Rise and fall times refer to VIL and VIH. Fig 17. I2C-bus timing diagram 9397 750 14939 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 01 — 14 February 2006 22 of 30 PCA9506 Philips Semiconductors 40-bit I2C-bus I/O port with RESET, OE, and INT ACK or read cycle START SCL SDA 30 % trst RESET 50 % 50 % 50 % trec(rst) tw(rst) trst 50 % IOx_y output off 002aac018 Fig 18. Reset timing 13. Test information VDD PULSE GENERATOR VI VO RL 500 Ω 2VDD open VSS DUT RT CL 50 pF 500 Ω 002aac019 RL = load resistance CL = load capacitance includes jig and probe capacitance RT = termination resistance should be equal to the output impedance Zo of the pulse generators. Fig 19. Test circuitry for switching times 9397 750 14939 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 01 — 14 February 2006 23 of 30 PCA9506 Philips Semiconductors 40-bit I2C-bus I/O port with RESET, OE, and INT 14. Package outline TSSOP56: plastic thin shrink small outline package; 56 leads; body width 6.1 mm SOT364-1 E D A X c HE y v M A Z 56 29 Q A2 (A 3) A1 pin 1 index A θ Lp L 1 detail X 28 w M bp e 2.5 0 5 mm scale DIMENSIONS (mm are the original dimensions). UNIT A max. A1 A2 A3 bp c D (1) E (2) e HE L Lp Q v w y Z θ mm 1.2 0.15 0.05 1.05 0.85 0.25 0.28 0.17 0.2 0.1 14.1 13.9 6.2 6.0 0.5 8.3 7.9 1 0.8 0.4 0.50 0.35 0.25 0.08 0.1 0.5 0.1 8 o 0 o Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT364-1 REFERENCES IEC JEDEC JEITA MO-153 EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-19 Fig 20. Package outline SOT364-1 (TSSOP56) 9397 750 14939 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 01 — 14 February 2006 24 of 30 PCA9506 Philips Semiconductors 40-bit I2C-bus I/O port with RESET, OE, and INT HVQFN56: plastic thermal enhanced very thin quad flat package; no leads; 56 terminals; body 8 x 8 x 0.85 mm A B D SOT684-1 terminal 1 index area A E A1 c detail X C e1 1/2 e e b 15 L y y1 C v M C A B w M C 28 29 14 e e2 Eh 1/2 e 1 42 terminal 1 index area 56 43 X Dh 0 2.5 scale DIMENSIONS (mm are the original dimensions) UNIT mm A(1) max. A1 b 1 0.05 0.00 0.30 0.18 5 mm c D(1) Dh E(1) Eh 0.2 8.1 7.9 4.45 4.15 8.1 7.9 4.45 4.15 e e1 6.5 0.5 e2 L v w y y1 6.5 0.5 0.3 0.1 0.05 0.05 0.1 Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC JEITA SOT684-1 --- MO-220 --- EUROPEAN PROJECTION ISSUE DATE 01-08-08 02-10-22 Fig 21. Package outline SOT684-1 (HVQFN56) 9397 750 14939 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 01 — 14 February 2006 25 of 30 PCA9506 Philips Semiconductors 40-bit I2C-bus I/O port with RESET, OE, and INT 15. Handling information Inputs and outputs are protected against electrostatic discharge in normal handling. However, to be totally safe, it is desirable to take precautions appropriate to handling MOS devices. Advice can be found in Data Handbook IC24 under “Handling MOS devices”. 16. Soldering 16.1 Introduction to soldering surface mount packages This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our Data Handbook IC26; Integrated Circuit Packages (document order number 9398 652 90011). There is no soldering method that is ideal for all surface mount IC packages. Wave soldering can still be used for certain surface mount ICs, but it is not suitable for fine pitch SMDs. In these situations reflow soldering is recommended. 16.2 Reflow soldering Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. Driven by legislation and environmental forces the worldwide use of lead-free solder pastes is increasing. Several methods exist for reflowing; for example, convection or convection/infrared heating in a conveyor type oven. Throughput times (preheating, soldering and cooling) vary between 100 seconds and 200 seconds depending on heating method. Typical reflow peak temperatures range from 215 °C to 270 °C depending on solder paste material. The top-surface temperature of the packages should preferably be kept: • below 225 °C (SnPb process) or below 245 °C (Pb-free process) – for all BGA, HTSSON..T and SSOP..T packages – for packages with a thickness ≥ 2.5 mm – for packages with a thickness < 2.5 mm and a volume ≥ 350 mm3 so called thick/large packages. • below 240 °C (SnPb process) or below 260 °C (Pb-free process) for packages with a thickness < 2.5 mm and a volume < 350 mm3 so called small/thin packages. Moisture sensitivity precautions, as indicated on packing, must be respected at all times. 16.3 Wave soldering Conventional single wave soldering is not recommended for surface mount devices (SMDs) or printed-circuit boards with a high component density, as solder bridging and non-wetting can present major problems. To overcome these problems the double-wave soldering method was specifically developed. If wave soldering is used the following conditions must be observed for optimal results: 9397 750 14939 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 01 — 14 February 2006 26 of 30 PCA9506 Philips Semiconductors 40-bit I2C-bus I/O port with RESET, OE, and INT • Use a double-wave soldering method comprising a turbulent wave with high upward pressure followed by a smooth laminar wave. • For packages with leads on two sides and a pitch (e): – larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be parallel to the transport direction of the printed-circuit board; – smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves at the downstream end. • For packages with leads on four sides, the footprint must be placed at a 45° angle to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves downstream and at the side corners. During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. Typical dwell time of the leads in the wave ranges from 3 seconds to 4 seconds at 250 °C or 265 °C, depending on solder material applied, SnPb or Pb-free respectively. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. 16.4 Manual soldering Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage (24 V or less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 °C. When using a dedicated tool, all other leads can be soldered in one operation within 2 seconds to 5 seconds between 270 °C and 320 °C. 16.5 Package related soldering information Table 12: Suitability of surface mount IC packages for wave and reflow soldering methods Package [1] Soldering method Wave Reflow [2] BGA, LBGA, LFBGA, SQFP, SSOP..T [3], TFBGA, VFBGA, XSON not suitable suitable DHVQFN, HBCC, HBGA, HLQFP, HSO, HSOP, HSQFP, HSSON, HTQFP, HTSSOP, HVQFN, HVSON, SMS not suitable [4] suitable PLCC [5], SO, SOJ suitable suitable HTSSON..T [3], suitable LQFP, QFP, TQFP not SSOP, TSSOP, VSO, VSSOP not recommended [7] suitable CWQCCN..L [8], not suitable not suitable [1] PMFP [9], WQCCN..L [8] For more detailed information on the BGA packages refer to the (LF)BGA Application Note (AN01026); order a copy from your Philips Semiconductors sales office. 9397 750 14939 Product data sheet recommended [5] [6] © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 01 — 14 February 2006 27 of 30 PCA9506 Philips Semiconductors 40-bit I2C-bus I/O port with RESET, OE, and INT [2] All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the maximum temperature (with respect to time) and body size of the package, there is a risk that internal or external package cracks may occur due to vaporization of the moisture in them (the so called popcorn effect). For details, refer to the Drypack information in the Data Handbook IC26; Integrated Circuit Packages; Section: Packing Methods. [3] These transparent plastic packages are extremely sensitive to reflow soldering conditions and must on no account be processed through more than one soldering cycle or subjected to infrared reflow soldering with peak temperature exceeding 217 °C ± 10 °C measured in the atmosphere of the reflow oven. The package body peak temperature must be kept as low as possible. [4] These packages are not suitable for wave soldering. On versions with the heatsink on the bottom side, the solder cannot penetrate between the printed-circuit board and the heatsink. On versions with the heatsink on the top side, the solder might be deposited on the heatsink surface. [5] If wave soldering is considered, then the package must be placed at a 45° angle to the solder wave direction. The package footprint must incorporate solder thieves downstream and at the side corners. [6] Wave soldering is suitable for LQFP, QFP and TQFP packages with a pitch (e) larger than 0.8 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm. [7] Wave soldering is suitable for SSOP, TSSOP, VSO and VSSOP packages with a pitch (e) equal to or larger than 0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm. [8] Image sensor packages in principle should not be soldered. They are mounted in sockets or delivered pre-mounted on flex foil. However, the image sensor package can be mounted by the client on a flex foil by using a hot bar soldering process. The appropriate soldering profile can be provided on request. [9] Hot bar soldering or manual soldering is suitable for PMFP packages. 17. Abbreviations Table 13: Abbreviations Acronym Description CDM Charged Device Model DUT Device Under Test ESD ElectroStatic Discharge HBM Human Body Model IC Integrated Circuit I2C-bus Inter IC bus LED Light Emitting Diode MM Machine Model PLC Programmable Logic Controller POR Power-On Reset PWM Pulse Width Modulation RAID Redundant Array of Independent Disks 18. Revision history Table 14: Revision history Document ID Release date Data sheet status Change notice Doc. number Supersedes PCA9506_1 20060214 Product data sheet - 9397 750 14939 - 9397 750 14939 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 01 — 14 February 2006 28 of 30 PCA9506 Philips Semiconductors 40-bit I2C-bus I/O port with RESET, OE, and INT 19. Data sheet status Level Data sheet status [1] Product status [2] [3] Definition I Objective data Development This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. II Preliminary data Qualification This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. III Product data Production This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). [1] Please consult the most recently issued data sheet before initiating or completing a design. [2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. [3] For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. 20. Definitions customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Right to make changes — Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status ‘Production’), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. 22. Trademarks Notice — All referenced brands, product names, service names and trademarks are the property of their respective owners. I2C-bus — logo is a trademark of Koninklijke Philips Electronics N.V. 21. Disclaimers Life support — These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors 23. Contact information For additional information, please visit: http://www.semiconductors.philips.com For sales office addresses, send an email to: [email protected] 9397 750 14939 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 01 — 14 February 2006 29 of 30 PCA9506 Philips Semiconductors 40-bit I2C-bus I/O port with RESET, OE, and INT 24. Contents 1 2 3 4 5 6 6.1 6.2 7 7.1 7.2 7.3 7.3.1 7.3.2 7.3.3 7.3.4 7.3.5 7.4 7.5 7.6 7.7 7.8 7.9 8 8.1 8.1.1 8.2 8.3 8.4 9 10 11 12 13 14 15 16 16.1 16.2 16.3 16.4 16.5 17 18 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 5 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 6 Functional description . . . . . . . . . . . . . . . . . . . 7 Device address . . . . . . . . . . . . . . . . . . . . . . . . . 7 Command register . . . . . . . . . . . . . . . . . . . . . . 7 Register definitions . . . . . . . . . . . . . . . . . . . . . . 9 IP0 to IP4 - Input Port registers . . . . . . . . . . . 10 OP0 to OP4 - Output Port registers . . . . . . . . 11 PI0 to PI4 - Polarity Inversion registers. . . . . . 11 IOC0 to IOC4 - I/O Configuration registers. . . 12 MSK0 to MSK4 - Mask interrupt registers . . . 12 Power-on reset . . . . . . . . . . . . . . . . . . . . . . . . 12 RESET input . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Interrupt output (INT) . . . . . . . . . . . . . . . . . . . 13 Output enable input (OE) . . . . . . . . . . . . . . . . 13 Live insertion . . . . . . . . . . . . . . . . . . . . . . . . . 13 Standby. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Characteristics of the I2C-bus. . . . . . . . . . . . . 14 Bit transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 START and STOP conditions . . . . . . . . . . . . . 14 System configuration . . . . . . . . . . . . . . . . . . . 14 Acknowledge . . . . . . . . . . . . . . . . . . . . . . . . . 15 Bus transactions . . . . . . . . . . . . . . . . . . . . . . . 15 Application design-in information . . . . . . . . . 18 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 19 Static characteristics. . . . . . . . . . . . . . . . . . . . 19 Dynamic characteristics . . . . . . . . . . . . . . . . . 21 Test information . . . . . . . . . . . . . . . . . . . . . . . . 23 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 24 Handling information. . . . . . . . . . . . . . . . . . . . 26 Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Introduction to soldering surface mount packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 26 Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 26 Manual soldering . . . . . . . . . . . . . . . . . . . . . . 27 Package related soldering information . . . . . . 27 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 28 19 20 21 22 23 Data sheet status. . . . . . . . . . . . . . . . . . . . . . . Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . Contact information . . . . . . . . . . . . . . . . . . . . 29 29 29 29 29 © Koninklijke Philips Electronics N.V. 2006 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Date of release: 14 February 2006 Document number: 9397 750 14939 Published in The Netherlands