PCA9552 16-bit I2C-bus LED driver with programmable blink rates Rev. 05 — 9 March 2006 Product data sheet 1. General description The PCA9552 LED blinker blinks LEDs in I2C-bus and SMBus applications where it is necessary to limit bus traffic or free up the I2C-bus master's (MCU, MPU, DSP, chip set, etc.) timer. The uniqueness of this device is the internal oscillator with two programmable blink rates. To blink LEDs using normal I/O expanders like the PCF8574 or PCA9554, the bus master must send repeated commands to turn the LED on and off. This greatly increases the amount of traffic on the I2C-bus and uses up one of the master's timers. The PCA9552 LED blinker instead requires only the initial setup command to program BLINK RATE 1 and BLINK RATE 2 (that is, the frequency and duty cycle) for each individual output. From then on, only one command from the bus master is required to turn each individual open-drain output on, off, or to cycle at BLINK RATE 1 or BLINK RATE 2. Maximum output sink current is 25 mA per bit and 200 mA per package. Any bits not used for controlling the LEDs can be used for General Purpose Parallel Input/Output (GPIO) expansion. The active LOW hardware reset pin (RESET) and Power-On Reset (POR) initializes the registers to their default state, all zeroes, causing the bits to be set HIGH (LED off). Three hardware address pins on the PCA9552 allow eight devices to operate on the same bus. 2. Features ■ 16 LED drivers (on, off, flashing at a programmable rate) ■ 2 selectable, fully programmable blink rates (frequency and duty cycle) between 0.172 Hz and 44 Hz (5.82 seconds and 0.023 seconds) ■ Input/outputs not used as LED drivers can be used as regular GPIOs ■ Internal oscillator requires no external components ■ I2C-bus interface logic compatible with SMBus ■ Internal power-on reset ■ Noise filter on SCL/SDA inputs ■ Active LOW reset input ■ 16 open-drain outputs directly drive LEDs to 25 mA ■ Edge rate control on outputs ■ No glitch on power-up ■ Supports hot insertion ■ Low standby current ■ Operating power supply voltage range of 2.3 V to 5.5 V ■ 0 Hz to 400 kHz clock frequency PCA9552 Philips Semiconductors 16-bit I2C-bus LED driver with programmable blink rates ■ ESD protection exceeds 2000 V HBM per JESD22-A114, 150 V MM per JESD22-A115 and 1000 V CDM per JESD22-C101 ■ Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA ■ Packages offered: SO24, TSSOP24, HVQFN24 3. Ordering information Table 1: Ordering information Tamb = −40 °C to +85 °C Type number Topside mark Package Name Description Version PCA9552D PCA9552D SO24 plastic small outline package; 24 leads; body width 7.5 mm SOT137-1 PCA9552PW PCA9552 TSSOP24 plastic thin shrink small outline package; 24 leads; body width 4.4 mm SOT355-1 PCA9552BS 9552 HVQFN24 plastic thermal enhanced very thin quad flat package; no leads; 24 terminals; body 4 × 4 × 0.85 mm SOT616-1 4. Block diagram A0 A1 A2 PCA9552 SCL SDA INPUT REGISTER INPUT FILTERS I2C-BUS CONTROL LED SELECT (LSn) REGISTER 1 VDD RESET 0 POWER-ON RESET OSCILLATOR LEDn PRESCALER 0 REGISTER PWM0 REGISTER BLINK0 PRESCALER 1 REGISTER PWM1 REGISTER BLINK1 VSS 002aac168 Remark: Only one I/O shown for clarity. Fig 1. Block diagram of PCA9552 PCA9552_5 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 05 — 9 March 2006 2 of 28 PCA9552 Philips Semiconductors 16-bit I2C-bus LED driver with programmable blink rates 5. Pinning information 5.1 Pinning A0 1 24 VDD A0 1 A1 2 23 SDA A1 2 24 VDD 23 SDA A2 3 22 SCL A2 3 22 SCL LED0 4 21 RESET LED0 4 21 RESET LED1 5 20 LED15 LED1 5 20 LED15 LED2 6 19 LED14 LED2 6 LED3 7 18 LED13 LED3 7 LED4 8 17 LED12 LED4 8 17 LED12 LED5 9 16 LED11 LED5 9 16 LED11 LED6 10 15 LED10 LED6 10 15 LED10 LED7 11 14 LED9 LED7 11 14 LED9 VSS 12 13 LED8 VSS 12 13 LED8 PCA9552D PCA9552PW 002aac165 19 LED14 18 LED13 002aac166 19 SCL 20 SDA 21 VDD 24 A2 terminal 1 index area 22 A0 Fig 3. Pin configuration for TSSOP24 23 A1 Fig 2. Pin configuration for SO24 LED0 1 18 RESET LED1 2 17 LED15 LED2 3 LED3 4 LED4 5 14 LED12 LED5 6 13 LED11 16 LED14 15 LED13 LED10 12 9 VSS LED9 11 8 LED7 LED8 10 7 LED6 PCA9552BS 002aac167 Transparent top view Fig 4. Pin configuration for HVQFN24 PCA9552_5 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 05 — 9 March 2006 3 of 28 PCA9552 Philips Semiconductors 16-bit I2C-bus LED driver with programmable blink rates 5.2 Pin description Table 2: Symbol Pin description Pin Description SO24, TSSOP24 HVQFN24 A0 1 22 address input 0 A1 2 23 address input 1 A2 3 24 address input 2 LED0 4 1 LED driver 0 LED1 5 2 LED driver 1 LED2 6 3 LED driver 2 LED3 7 4 LED driver 3 LED4 8 5 LED driver 4 LED5 9 6 LED driver 5 LED6 10 7 LED driver 6 LED7 11 8 LED driver 7 VSS 12 9 [1] ground supply LED8 13 10 LED driver 8 LED9 14 11 LED driver 9 LED10 15 12 LED driver 10 LED11 16 13 LED driver 11 LED12 17 14 LED driver 12 LED13 18 15 LED driver 13 LED14 19 16 LED driver 14 LED15 20 17 LED driver 15 RESET 21 18 active LOW reset input SCL 22 19 serial clock line SDA 23 20 serial data line VDD 24 21 supply voltage [1] HVQFN package die supply ground is connected to both VSS pin and exposed center pad. VSS pin must be connected to supply ground for proper device operation. For enhanced thermal, electrical, and board level performance, the exposed pad needs to be soldered to the board using a corresponding thermal pad on the board and for proper heat conduction through the board, thermal vias need to be incorporated in the printed-circuit board in the thermal pad region. PCA9552_5 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 05 — 9 March 2006 4 of 28 PCA9552 Philips Semiconductors 16-bit I2C-bus LED driver with programmable blink rates 6. Functional description Refer to Figure 1 “Block diagram of PCA9552”. 6.1 Device address Following a START condition, the bus master must output the address of the slave it is accessing. The address of the PCA9552 is shown in Figure 5. To conserve power, no internal pull-up resistors are incorporated on the hardware selectable address pins and they must be pulled HIGH or LOW. slave address 1 1 0 0 fixed A2 A1 A0 R/W programmable 002aac169 Fig 5. PCA9552 address The last bit of the address byte defines the operation to be performed. When set to logic 1 a read is selected, while a logic 0 selects a write operation. 6.2 Control Register Following the successful acknowledgement of the slave address, the bus master will send a byte to the PCA9552, which will be stored in the Control Register. This register can be read and written via the I2C-bus. 0 0 0 AI Auto-Increment flag B3 B2 B1 B0 register address 002aac170 Reset state: 00h Fig 6. Control Register The lowest 3 bits are used as a pointer to determine which register will be accessed. If the Auto-Increment flag (AI) is set, the four low order bits of the Control Register are automatically incremented after a read or write. This allows the user to program the registers sequentially. The contents of these bits will rollover to ‘0000’ after the last register is accessed. When the Auto-Increment flag is set (AI = 1) and a read sequence is initiated, the sequence must start by reading a register different from ‘0' (B3 B2 B1 B0 ≠ 0000). Only the 4 least significant bits are affected by the AI flag. Unused bits must be programmed with zeroes. PCA9552_5 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 05 — 9 March 2006 5 of 28 PCA9552 Philips Semiconductors 16-bit I2C-bus LED driver with programmable blink rates 6.2.1 Control Register definition Table 3: Register summary B3 B2 B1 B0 Symbol Access Description 0 0 0 0 INPUT0 read only input register 0 0 0 0 1 INPUT1 read only input register 1 0 0 1 0 PSC0 read/write frequency prescaler 0 0 0 1 1 PWM0 read/write PWM register 0 0 1 0 0 PSC1 read/write frequency prescaler 1 0 1 0 1 PWM1 read/write PWM register 1 0 1 1 0 LS0 read/write LED0 to LED3 selector 0 1 1 1 LS1 read/write LED4 to LED7 selector 1 0 0 0 LS2 read/write LED8 to LED11 selector 1 0 0 1 LS3 read/write LED12 to LED15 selector 6.3 Register descriptions 6.3.1 INPUT0 - Input register 0 The Input register 0 reflects the state of the device pins (inputs LED0 to LED7). Writes to this register will be acknowledged but will have no effect. Table 4: Bit INPUT0 - input register 0 description 7 6 5 4 3 2 1 0 Symbol LED7 LED6 LED5 LED4 LED3 LED2 LED1 LED0 Default X X X X X X X X Remark: The default value ‘X’ is determined by the externally applied logic level (normally logic 1) when used for directly driving LED with pull-up to VDD. 6.3.2 INPUT1 - Input register 1 The Input register 1 reflects the state of the device pins (inputs LED8 to LED15). Writes to this register will be acknowledged but will have no effect. Table 5: Bit INPUT1 - input register 1 description 7 6 5 4 3 2 1 0 Symbol LED15 LED14 LED13 LED12 LED11 LED10 LED9 LED8 Default X X X X X X X X Remark: The default value ‘X’ is determined by the externally applied logic level (normally logic 1) when used for directly driving LED with pull-up to VDD. PCA9552_5 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 05 — 9 March 2006 6 of 28 PCA9552 Philips Semiconductors 16-bit I2C-bus LED driver with programmable blink rates 6.3.3 PCS0 - Frequency Prescaler 0 PSC0 is used to program the period of the PWM output. The period of BLINK0 = (PSC0 + 1) / 44. Table 6: Bit PSC0 - Frequency Prescaler 0 register description 7 6 5 4 3 2 1 0 Symbol PSC0[7] PSC0[6] PSC0[5] PSC0[4] PSC0[3] PSC0[2] PSC0[1] PSC0[0] Default 1 1 1 1 1 1 1 1 6.3.4 PWM0 - Pulse Width Modulation 0 The PWM0 register determines the duty cycle of BLINK0. The outputs are LOW (LED off) when the count is less than the value in PWM0 and HIGH when it is greater. If PWM0 is programmed with 00h, then the PWM0 output is always LOW. The duty cycle of BLINK0 = (256 − PWM0) / 256. Table 7: Bit PWM0 - Pulse Width Modulation 0 register description 7 6 5 4 3 2 1 0 Symbol PWM0 [7] PWM0 [6] PWM0 [5] PWM0 [4] PWM0 [3] PWM0 [2] PWM0 [1] PWM0 [0] Default 1 0 0 0 0 0 0 0 6.3.5 PCS1 - Frequency Prescaler 1 PSC1 is used to program the period of the PWM output. The period of BLINK1 = (PSC1 + 1) / 44. Table 8: Bit PSC1 - Frequency Prescaler 1 register description 7 6 5 4 3 2 1 0 Symbol PSC1[7] PSC1[6] PSC1[5] PSC1[4] PSC1[3] PSC1[2] PSC1[1] PSC1[0] Default 1 1 1 1 1 1 1 1 6.3.6 PWM1 - Pulse Width Modulation 1 The PWM1 register determines the duty cycle of BLINK1. The outputs are LOW (LED off) when the count is less than the value in PWM1 and HIGH when it is greater. If PWM1 is programmed with 00h, then the PWM1 output is always LOW. The duty cycle of BLINK1 = (256 − PWM1) / 256. Table 9: Bit PWM1 - Pulse Width Modulation 1 register description 7 6 5 4 3 2 1 0 Symbol PWM1 [7] PWM1 [6] PWM1 [5] PWM1 [4] PWM1 [3] PWM1 [2] PWM1 [1] PWM1 [0] Default 1 0 0 0 0 0 0 0 PCA9552_5 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 05 — 9 March 2006 7 of 28 PCA9552 Philips Semiconductors 16-bit I2C-bus LED driver with programmable blink rates 6.3.7 LS0 to LS3 - LED selector registers The LSn LED select registers determine the source of the LED data. 00 = output is set LOW (LED on) 01 = output is set high-impedance (LED off; default) 10 = output blinks at PWM0 rate 11 = output blinks at PWM1 rate Table 10: LS0 to LS3 - LED selector registers bit description Legend: * default value Register Bit Value Description LS0 - LED0 to LED3 selector LS0 7:6 01* LED3 selected 5:4 01* LED2 selected 3:2 01* LED1 selected 1:0 01* LED0 selected LS1 - LED4 to LED7 selector LS1 7:6 01* LED7 selected 5:4 01* LED6 selected 3:2 01* LED5 selected 1:0 01* LED4 selected LS2 - LED8 to LED11 selector LS2 7:6 01* LED11 selected 5:4 01* LED10 selected 3:2 01* LED9 selected 1:0 01* LED8 selected LS3 - LED12 to LED15 selector LS3 7:6 01* LED15 selected 5:4 01* LED14 selected 3:2 01* LED13 selected 1:0 01* LED12 selected PCA9552_5 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 05 — 9 March 2006 8 of 28 PCA9552 Philips Semiconductors 16-bit I2C-bus LED driver with programmable blink rates 6.4 Pins used as GPIOs LED pins not used to control LEDs can be used as general purpose I/Os (GPIOs). For use as input, set LEDn to high-impedance (01) and then read the pin state via the input register. For use as output, connect external pull-up resistor to the pin and size it according to the DC recommended operating characteristics. LED output pin is HIGH when the output is programmed as high-impedance, and LOW when the output is programmed LOW through the ‘LED selector’ register. The output can be pulse-width controlled when PWM0 or PWM1 are used. 6.5 Power-on reset When power is applied to VDD, an internal Power-On Reset (POR) holds the PCA9552 in a reset condition until VDD has reached VPOR. At that point, the reset condition is released and the PCA9552 registers are initialized to their default states. Thereafter, VDD must be lowered below 0.2 V to reset the device. 6.6 External RESET A reset can be accomplished by holding the RESET pin LOW for a minimum of tw(rst). The PCA9552 registers and I2C-bus state machine will be held in their default states until the RESET input is once again HIGH. This input requires a pull-up resistor to VDD if no active connection is used. PCA9552_5 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 05 — 9 March 2006 9 of 28 PCA9552 Philips Semiconductors 16-bit I2C-bus LED driver with programmable blink rates 7. Characteristics of the I2C-bus The I2C-bus is for 2-way, 2-line communication between different ICs or modules. The two lines are a serial data line (SDA) and a serial clock line (SCL). Both lines must be connected to a positive supply via a pull-up resistor when connected to the output stages of a device. Data transfer may be initiated only when the bus is not busy. 7.1 Bit transfer One data bit is transferred during each clock pulse. The data on the SDA line must remain stable during the HIGH period of the clock pulse as changes in the data line at this time will be interpreted as control signals (see Figure 7). SDA SCL data line stable; data valid change of data allowed mba607 Fig 7. Bit transfer 7.1.1 START and STOP conditions Both data and clock lines remain HIGH when the bus is not busy. A HIGH-to-LOW transition of the data line while the clock is HIGH is defined as the START condition (S). A LOW-to-HIGH transition of the data line while the clock is HIGH is defined as the STOP condition (P) (see Figure 8.) SDA SDA SCL SCL S P START condition STOP condition mba608 Fig 8. Definition of START and STOP conditions 7.2 System configuration A device generating a message is a ‘transmitter'; a device receiving is the ‘receiver'. The device that controls the message is the ‘master' and the devices which are controlled by the master are the ‘slaves' (see Figure 9). PCA9552_5 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 05 — 9 March 2006 10 of 28 PCA9552 Philips Semiconductors 16-bit I2C-bus LED driver with programmable blink rates SDA SCL MASTER TRANSMITTER/ RECEIVER SLAVE RECEIVER SLAVE TRANSMITTER/ RECEIVER MASTER TRANSMITTER MASTER TRANSMITTER/ RECEIVER I2C-BUS MULTIPLEXER SLAVE 002aaa966 Fig 9. System configuration 7.3 Acknowledge The number of data bytes transferred between the START and the STOP conditions from transmitter to receiver is not limited. Each byte of eight bits is followed by one acknowledge bit. The acknowledge bit is a HIGH level put on the bus by the transmitter, whereas the master generates an extra acknowledge related clock pulse. A slave receiver which is addressed must generate an acknowledge after the reception of each byte. Also a master must generate an acknowledge after the reception of each byte that has been clocked out of the slave transmitter. The device that acknowledges has to pull down the SDA line during the acknowledge clock pulse, so that the SDA line is stable LOW during the HIGH period of the acknowledge related clock pulse; set-up and hold times must be taken into account. A master receiver must signal an end of data to the transmitter by not generating an acknowledge on the last byte that has been clocked out of the slave. In this event, the transmitter must leave the data line HIGH to enable the master to generate a STOP condition. data output by transmitter not acknowledge data output by receiver acknowledge SCL from master 1 S START condition 2 8 9 clock pulse for acknowledgement 002aaa987 Fig 10. Acknowledgement on the I2C-bus PCA9552_5 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 05 — 9 March 2006 11 of 28 PCA9552 Philips Semiconductors 16-bit I2C-bus LED driver with programmable blink rates 7.4 Bus transactions SCL 1 2 3 4 5 6 7 8 9 slave address SDA S 1 1 0 data to register command byte 0 A2 A1 A0 0 START condition A R/W 0 0 0 AI B3 B2 B1 B0 A DATA 1 A acknowledge from slave acknowledge from slave acknowledge from slave write to register tv(Q) data out from port DATA 1 VALID 002aac185 Fig 11. Write to register slave address SDA S 1 1 0 command byte 0 A2 A1 A0 0 START condition 0 A 0 1 1 0 0 A2 A1 A0 1 (repeated) START condition (cont.) AI B3 B2 B1 B0 A acknowledge from slave R/W acknowledge from slave slave address (cont.) S 0 data from register DATA (first byte) A Auto-Increment register address if AI = 1 R/W acknowledge from slave data from register DATA (last byte) A acknowledge from master NA P STOP condition no acknowledge from master at this moment master-transmitter becomes master-receiver and slave-receiver becomes slave-transmitter 002aac186 Fig 12. Read from register no acknowledge from master slave address SDA S 1 1 0 0 A2 A1 A0 1 START condition data from port data from port R/W A A DATA 1 DATA 4 acknowledge from master acknowledge from slave NA P STOP condition read from port th(D) data into port tsu(D) DATA 2 DATA 3 DATA 4 002aac187 Remark: This figure assumes the command byte has previously been programmed with 00h. Fig 13. Read Input Port register PCA9552_5 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 05 — 9 March 2006 12 of 28 PCA9552 Philips Semiconductors 16-bit I2C-bus LED driver with programmable blink rates 8. Application design-in information 5V 5V I2C-BUS/SMBus MASTER SDA 10 kΩ (3×) SCL VDD SDA LED0 SCL LED1 LED2 LED3 RESET LED4 LED5 LED6 PCA9552 LED7 LED8 LED9 LED10 A2 LED11 A1 LED12 A0 LED13 VSS LED14 GPIOs LED15 002aac188 LED0 to LED12 are used as LED drivers. LED13 to LED15 are used as regular GPIOs. Fig 14. Typical application 8.1 Minimizing IDD when the I/O is used to control LEDs When the I/Os are used to control LEDs, they are normally connected to VDD through a resistor as shown in Figure 15. Since the LED acts as a diode, when the LED is off the I/O VI is about 1.2 V less than VDD. The supply current, IDD, increases as VI becomes lower than VDD and is specified as ∆Istb in Table 13 “Static characteristics”. Designs needing to minimize current consumption, such as battery power applications, should consider maintaining the I/O pins greater than or equal to VDD when the LED is off. Figure 15 shows a high value resistor in parallel with the LED. Figure 16 shows VDD less than the LED supply voltage by at least 1.2 V. Both of these methods maintain the input/output VI at or above VDD and prevents additional supply current consumption when the LED is off. PCA9552_5 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 05 — 9 March 2006 13 of 28 PCA9552 Philips Semiconductors 16-bit I2C-bus LED driver with programmable blink rates 3.3 V VDD VDD LED VDD 100 kΩ LEDn 5V LED LEDn 002aac189 Fig 15. High value resistor in parallel with the LED 002aac190 Fig 16. Device supplied by a lower voltage 8.2 Programming example The following example will show how to set LED0 to LED3 on. It will then set LED4 and LED5 to blink at 1 Hz at a 50 % duty cycle. LED6 and LED7 will be set to blink at 4 Hz and at a 25 % duty cycle. LED8 to LED15 will be set to off. Table 11: Programming PCA9552 Program sequence I2C-bus START S PCA9552 address with A0 to A2 = LOW C0h PSC0 subaddress + Auto-Increment 12h Set prescaler PSC0 to achieve a period of 1 second: 2Bh PSC0 + 1 Blink period = 1 = ----------------------44 PSC0 = 43 Set PWM0 duty cycle to 50 %: 80h 256 – PWM0 -------------------------------- = 0.5 256 PWM0 = 128 Set prescaler PCS1 to achieve a period of 0.25 seconds: 0Ah PSC1 + 1 Blink period = 0.25 = ----------------------44 PSC1 = 10 Set PWM1 output duty cycle to 25 %: C0h 256 – PWM1 -------------------------------- = 0.25 256 PWM1 = 192 Set LED0 to LED3 on 00h Set LED4 and LED5 to PWM0, and LED6 or LED7 to PWM1 FAh Set LED8 to LED11 off 55h Set LED12 to LED15 off 55h STOP P PCA9552_5 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 05 — 9 March 2006 14 of 28 PCA9552 Philips Semiconductors 16-bit I2C-bus LED driver with programmable blink rates 9. Limiting values Table 12: Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter Conditions Min Max Unit VDD supply voltage −0.5 +6.0 V VI/O voltage on an input/output pin IO(LEDn) output current on pin LEDn LEDn used as an I/O VSS − 0.5 5.5 V LEDn used as an I/O - ±25 mA ISS ground supply current - 200 mA Ptot total power dissipation - 400 mW Tstg storage temperature −65 +150 °C Tamb ambient temperature −40 +85 °C operating 10. Static characteristics Table 13: Static characteristics VDD = 2.3 V to 5.5 V; VSS = 0 V; Tamb = −40 °C to +85 °C; unless otherwise specified. Symbol Parameter Conditions Min Typ [1] Max Unit Supply VDD supply voltage 2.3 - 5.5 V IDD supply current Operating mode; VDD = 5.5 V; no load; VI = VDD or VSS; fSCL = 100 kHz - 350 550 µA Istb standby current Standby mode; VDD = 5.5 V; no load; VI = VDD or VSS; fSCL = 0 kHz - 2.1 5.0 µA ∆Istb additional standby current Standby mode; VDD = 5.5 V; every LED I/O at VI = 4.3 V; fSCL = 0 kHz - - 2 mA VPOR power-on reset voltage [2] VDD = 3.3 V; no load; VI = VDD or VSS - 1.7 2.2 V Input SCL; input/output SDA VIL LOW-level input voltage −0.5 - 0.3VDD V VIH HIGH-level input voltage 0.7VDD - 5.5 V IOL LOW-level output current VOL = 0.4 V 3 6.5 - mA IL leakage current VI = VDD = VSS −1 - +1 µA Ci input capacitance VI = VSS - 4.4 5 pF I/Os VIL LOW-level input voltage −0.5 - 0.8 V VIH HIGH-level input voltage 2.0 - 5.5 V IOL LOW-level output current ILI input leakage current Cio input/output capacitance VOL = 0.4 V; VDD = 2.3 V [3] 9 - - mA VOL = 0.4 V; VDD = 3.0 V [3] 12 - - mA VOL = 0.4 V; VDD = 5.0 V [3] 15 - - mA VOL = 0.7 V; VDD = 2.3 V [3] 15 - - mA VOL = 0.7 V; VDD = 3.0 V [3] 20 - - mA VOL = 0.7 V; VDD = 5.0 V [3] 25 - - mA VDD = 3.6 V; VI = 0 V or VDD PCA9552_5 Product data sheet −1 - +1 µA - 2.6 5 pF © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 05 — 9 March 2006 15 of 28 PCA9552 Philips Semiconductors 16-bit I2C-bus LED driver with programmable blink rates Table 13: Static characteristics …continued VDD = 2.3 V to 5.5 V; VSS = 0 V; Tamb = −40 °C to +85 °C; unless otherwise specified. Symbol Parameter Conditions Min Typ [1] Max Unit Select inputs A0, A1, A2; RESET VIL LOW-level input voltage −0.5 - 0.8 V VIH HIGH-level input voltage 2.0 - 5.5 V ILI input leakage current −1 - +1 µA Ci input capacitance - 2.3 5 pF [1] All typical values at 3.3 V and 25 °C. [2] VDD must be lowered to 0.2 V in order to reset part. [3] Each I/O must be externally limited to a maximum of 25 mA and each octal ([LED0 to LED7] and [LED8 to LED15]) must be limited to a maximum current of 100 mA for a device total of 200 mA. 20 % VI = VSS 002aac191 (1) percent variation 20 % 002aac192 (1) percent variation 0% 0% (2) −20 % (3) (2) −20 % (3) −40 % −40 −20 0 20 40 60 100 Tamb (°C) 80 −40 % −40 −20 (1) maximum (1) maximum (2) average (2) average (3) minimum (3) minimum Fig 17. Typical frequency variation over process at VDD = 2.3 V to 3.0 V 20 40 60 100 80 Tamb (°C) Fig 18. Typical frequency variation over process at VDD = 3.0 V to 5.5 V PCA9552_5 Product data sheet 0 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 05 — 9 March 2006 16 of 28 PCA9552 Philips Semiconductors 16-bit I2C-bus LED driver with programmable blink rates 11. Dynamic characteristics Table 14: Dynamic characteristics Symbol Parameter Conditions Standard mode I2C-bus Min Max Fast mode I2C-bus Min Max Unit fSCL SCL clock frequency 0 100 0 400 tBUF bus free time between a STOP and START condition 4.7 - 1.3 - µs tHD;STA hold time (repeated) START condition 4.0 - 0.6 - µs tSU;STA set-up time for a repeated START condition 4.7 - 0.6 - µs tSU;STO set-up time for STOP condition 4.0 - 0.6 - µs tHD;DAT data hold time tVD;ACK data valid acknowledge time tVD;DAT data valid time kHz 0 - 0 - ns [1] - 600 - 600 ns LOW-level [2] - 600 - 600 ns HIGH-level [2] - 1500 - 600 ns tSU;DAT data set-up time 250 - 100 - ns tLOW LOW period of the SCL clock 4.7 - 1.3 - µs tHIGH HIGH period of the SCL clock 4.0 - 0.6 - µs 20 + 0.1Cb [3] 300 ns 20 + 0.1Cb [3] 300 ns fall time of both SDA and SCL signals tf - 300 tr rise time of both SDA and SCL signals - 1000 tSP pulse width of spikes that must be suppressed by the input filter - 50 - 50 ns 250 - 250 ns Port timing tv(Q) data output valid time - tsu(D) data input setup time 100 - 100 - ns th(D) data input hold time 1 - 1 - µs tw(rst) reset pulse width 10 - 10 - ns trec(rst) reset recovery time trst reset time Reset [4] [5] 0 - 0 - ns 400 - 400 - ns [1] tVD;ACK = time for Acknowledgement signal from SCL LOW to SDA (out) LOW. [2] tVD;DAT = minimum time for SDA data out to be valid following SCL LOW. [3] Cb = total capacitance of one bus line in pF. [4] Resetting the device while actively communicating on the bus may cause glitches or errant STOP conditions. [5] Upon reset, the full delay will be the sum of trst and the RC time constant of the SDA bus. PCA9552_5 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 05 — 9 March 2006 17 of 28 PCA9552 Philips Semiconductors 16-bit I2C-bus LED driver with programmable blink rates SDA tr tBUF tf tHD;STA tSP tLOW SCL tHD;STA P tSU;STA tHD;DAT S tHIGH tSU;DAT tSU;STO Sr P 002aaa986 Fig 19. Definition of timing on the I2C-bus protocol START condition (S) tSU;STA bit 7 MSB (A7) tLOW bit 6 (A6) tHIGH bit 0 (R/W) STOP condition (P) acknowledge (A) 1/f SCL SCL tBUF tr tf SDA tHD;STA tSU;DAT tHD;DAT tVD;DAT tVD;ACK tSU;STO 002aab175 Rise and fall times refer to VIL and VIH. Fig 20. I2C-bus timing diagram ACK or read cycle START SCL SDA 30 % trst RESET 50 % 50 % trec(rst) 50 % tw(rst) trst LEDn 50 % LED off 002aac193 Fig 21. Reset timing PCA9552_5 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 05 — 9 March 2006 18 of 28 PCA9552 Philips Semiconductors 16-bit I2C-bus LED driver with programmable blink rates 12. Test information VDD PULSE GENERATOR VI VO RL 500 Ω VDD open GND D.U.T. RT CL 50 pF 002aab284 RL = load resistor for LEDn. RL for SDA and SCL > 1 kΩ (3 mA or less current) CL = load capacitance includes jig and probe capacitance RT = termination resistance should be equal to the output impedance Zo of the pulse generators. Fig 22. Test circuitry for switching times PCA9552_5 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 05 — 9 March 2006 19 of 28 PCA9552 Philips Semiconductors 16-bit I2C-bus LED driver with programmable blink rates 13. Package outline SO24: plastic small outline package; 24 leads; body width 7.5 mm SOT137-1 D E A X c HE y v M A Z 24 13 Q A2 A (A 3) A1 pin 1 index θ Lp L 1 12 e detail X w M bp 0 5 10 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (1) e HE L Lp Q v w y mm 2.65 0.3 0.1 2.45 2.25 0.25 0.49 0.36 0.32 0.23 15.6 15.2 7.6 7.4 1.27 10.65 10.00 1.4 1.1 0.4 1.1 1.0 0.25 0.25 0.1 0.01 0.019 0.013 0.014 0.009 0.61 0.60 0.30 0.29 0.05 0.419 0.043 0.055 0.394 0.016 inches 0.1 0.012 0.096 0.004 0.089 0.043 0.039 0.01 0.01 Z (1) 0.9 0.4 0.035 0.004 0.016 θ o 8 o 0 Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC SOT137-1 075E05 MS-013 JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-19 Fig 23. Package outline SOT137-1 (SO24) PCA9552_5 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 05 — 9 March 2006 20 of 28 PCA9552 Philips Semiconductors 16-bit I2C-bus LED driver with programmable blink rates TSSOP24: plastic thin shrink small outline package; 24 leads; body width 4.4 mm D SOT355-1 E A X c HE y v M A Z 13 24 Q A2 (A 3) A1 pin 1 index A θ Lp L 1 12 bp e detail X w M 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (2) e HE L Lp Q v w y Z (1) θ mm 1.1 0.15 0.05 0.95 0.80 0.25 0.30 0.19 0.2 0.1 7.9 7.7 4.5 4.3 0.65 6.6 6.2 1 0.75 0.50 0.4 0.3 0.2 0.13 0.1 0.5 0.2 8o 0o Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT355-1 REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-19 MO-153 Fig 24. Package outline SOT355-1 (TSSOP24) PCA9552_5 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 05 — 9 March 2006 21 of 28 PCA9552 Philips Semiconductors 16-bit I2C-bus LED driver with programmable blink rates HVQFN24: plastic thermal enhanced very thin quad flat package; no leads; 24 terminals; body 4 x 4 x 0.85 mm A B D SOT616-1 terminal 1 index area A A1 E c detail X e1 C 1/2 e e 12 y y1 C v M C A B w M C b 7 L 13 6 e e2 Eh 1/2 e 1 18 terminal 1 index area 24 19 X Dh 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A(1) max. A1 b c D (1) Dh E (1) Eh e e1 e2 L v w y y1 mm 1 0.05 0.00 0.30 0.18 0.2 4.1 3.9 2.25 1.95 4.1 3.9 2.25 1.95 0.5 2.5 2.5 0.5 0.3 0.1 0.05 0.05 0.1 Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC JEITA SOT616-1 --- MO-220 --- EUROPEAN PROJECTION ISSUE DATE 01-08-08 02-10-22 Fig 25. Package outline SOT616-1 (HVQFN24) PCA9552_5 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 05 — 9 March 2006 22 of 28 PCA9552 Philips Semiconductors 16-bit I2C-bus LED driver with programmable blink rates 14. Handling information Inputs and outputs are protected against electrostatic discharge in normal handling. However, to be completely safe you must take normal precautions appropriate to handling integrated circuits. 15. Soldering 15.1 Introduction to soldering surface mount packages This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our Data Handbook IC26; Integrated Circuit Packages (document order number 9398 652 90011). There is no soldering method that is ideal for all surface mount IC packages. Wave soldering can still be used for certain surface mount ICs, but it is not suitable for fine pitch SMDs. In these situations reflow soldering is recommended. 15.2 Reflow soldering Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. Driven by legislation and environmental forces the worldwide use of lead-free solder pastes is increasing. Several methods exist for reflowing; for example, convection or convection/infrared heating in a conveyor type oven. Throughput times (preheating, soldering and cooling) vary between 100 seconds and 200 seconds depending on heating method. Typical reflow peak temperatures range from 215 °C to 270 °C depending on solder paste material. The top-surface temperature of the packages should preferably be kept: • below 225 °C (SnPb process) or below 245 °C (Pb-free process) – for all BGA, HTSSON..T and SSOP..T packages – for packages with a thickness ≥ 2.5 mm – for packages with a thickness < 2.5 mm and a volume ≥ 350 mm3 so called thick/large packages. • below 240 °C (SnPb process) or below 260 °C (Pb-free process) for packages with a thickness < 2.5 mm and a volume < 350 mm3 so called small/thin packages. Moisture sensitivity precautions, as indicated on packing, must be respected at all times. 15.3 Wave soldering Conventional single wave soldering is not recommended for surface mount devices (SMDs) or printed-circuit boards with a high component density, as solder bridging and non-wetting can present major problems. To overcome these problems the double-wave soldering method was specifically developed. If wave soldering is used the following conditions must be observed for optimal results: PCA9552_5 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 05 — 9 March 2006 23 of 28 PCA9552 Philips Semiconductors 16-bit I2C-bus LED driver with programmable blink rates • Use a double-wave soldering method comprising a turbulent wave with high upward pressure followed by a smooth laminar wave. • For packages with leads on two sides and a pitch (e): – larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be parallel to the transport direction of the printed-circuit board; – smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves at the downstream end. • For packages with leads on four sides, the footprint must be placed at a 45° angle to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves downstream and at the side corners. During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. Typical dwell time of the leads in the wave ranges from 3 seconds to 4 seconds at 250 °C or 265 °C, depending on solder material applied, SnPb or Pb-free respectively. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. 15.4 Manual soldering Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage (24 V or less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 °C. When using a dedicated tool, all other leads can be soldered in one operation within 2 seconds to 5 seconds between 270 °C and 320 °C. 15.5 Package related soldering information Table 15: Suitability of surface mount IC packages for wave and reflow soldering methods Package [1] Soldering method Wave Reflow [2] BGA, LBGA, LFBGA, SQFP, SSOP..T [3], TFBGA, VFBGA, XSON not suitable suitable DHVQFN, HBCC, HBGA, HLQFP, HSO, HSOP, HSQFP, HSSON, HTQFP, HTSSOP, HVQFN, HVSON, SMS not suitable [4] suitable PLCC [5], SO, SOJ suitable suitable HTSSON..T [3], suitable LQFP, QFP, TQFP not SSOP, TSSOP, VSO, VSSOP not recommended [7] suitable CWQCCN..L [8], not suitable not suitable [1] PMFP [9], WQCCN..L [8] For more detailed information on the BGA packages refer to the (LF)BGA Application Note (AN01026); order a copy from your Philips Semiconductors sales office. PCA9552_5 Product data sheet recommended [5] [6] © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 05 — 9 March 2006 24 of 28 PCA9552 Philips Semiconductors 16-bit I2C-bus LED driver with programmable blink rates [2] All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the maximum temperature (with respect to time) and body size of the package, there is a risk that internal or external package cracks may occur due to vaporization of the moisture in them (the so called popcorn effect). For details, refer to the Drypack information in the Data Handbook IC26; Integrated Circuit Packages; Section: Packing Methods. [3] These transparent plastic packages are extremely sensitive to reflow soldering conditions and must on no account be processed through more than one soldering cycle or subjected to infrared reflow soldering with peak temperature exceeding 217 °C ± 10 °C measured in the atmosphere of the reflow oven. The package body peak temperature must be kept as low as possible. [4] These packages are not suitable for wave soldering. On versions with the heatsink on the bottom side, the solder cannot penetrate between the printed-circuit board and the heatsink. On versions with the heatsink on the top side, the solder might be deposited on the heatsink surface. [5] If wave soldering is considered, then the package must be placed at a 45° angle to the solder wave direction. The package footprint must incorporate solder thieves downstream and at the side corners. [6] Wave soldering is suitable for LQFP, QFP and TQFP packages with a pitch (e) larger than 0.8 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm. [7] Wave soldering is suitable for SSOP, TSSOP, VSO and VSSOP packages with a pitch (e) equal to or larger than 0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm. [8] Image sensor packages in principle should not be soldered. They are mounted in sockets or delivered pre-mounted on flex foil. However, the image sensor package can be mounted by the client on a flex foil by using a hot bar soldering process. The appropriate soldering profile can be provided on request. [9] Hot bar soldering or manual soldering is suitable for PMFP packages. 16. Abbreviations Table 16: Abbreviations Acronym Description CDM Charged Device Model DSP Digital Signal Processor ESD ElectroStatic Discharge HBM Human Body Model GPIO General Purpose Input/Output IC Integrated Circuit I2C-bus Inter IC bus LED Light Emitting Diode MCU Microcontroller MM Machine Model MPU Microprocessor POR Power-On Reset PWM Pulse Width Modulation SMBus System Management Bus PCA9552_5 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 05 — 9 March 2006 25 of 28 PCA9552 Philips Semiconductors 16-bit I2C-bus LED driver with programmable blink rates 17. Revision history Table 17: Revision history Document ID Release date Data sheet status Change notice Doc. number Supersedes PCA9552_5 20060309 Product data sheet - - PCA9552_4 Modifications: • The format of this data sheet has been redesigned to comply with the new presentation and information standard of Philips Semiconductors. • Table 1 “Ordering information”: changed Topside mark of TSSOP24 package from ‘PCA9552PW’ to ‘PCA9552’ • • • • • Table 2 “Pin description”: added Table note 1 regarding VSS pin on HVQFN24 package Section 6.6 “External RESET”: changed symbol “tW” to “tw(rst)” Figure 11: changed symbol “tpv” to “tv(Q)” Figure 13: changed symbol “tph” to “th(D)”; changed symbol “tps” to “tsu(D)” Section 8.1 “Minimizing IDD when the I/O is used to control LEDs”: – 1st paragraph, 3rd sentence: changed symbol “∆IDD” to “∆Istb” – 2nd paragraph, 4th sentence: changed symbol “VIN” to “VI” • Table 12 “Limiting values”: – changed parameter description of VI/O from “DC voltage on an I/O” to “voltage on an input/output pin” – changed symbol “II/O (DC output current on an I/O)” to ‘IO(LEDn) (output current on pin LEDn) • Table 13 “Static characteristics”: – moved second sentence of description below title to (new)Table note 1 and added its reference at column “Typ” – changed symbol “∆IDD” to “∆Istb” – under subsection “I/Os”, changed symbol “IL” to “ILI” • Table 14 “Dynamic characteristics”: – updated parameter descriptions – under subsection “Port timing”: changed symbol “tPV” to “tv(Q)”; changed symbol “tPS” to “tsu(D)”; changed symbol “tPH” to “th(D)” – under subsection “Reset”: changed symbol “tW” to “tw(rst)”; changed symbol “tREC” to “trec(rst)”; changed symbol “tRESET” to “trst” (also in Table note 5) • Figure 21 “Reset timing” modified to harmonize letter symbols PCA9552_4 20041001 Product data sheet - 9397 750 13727 PCA9552_3 PCA9552_3 20030502 Product data 853-2374 29857 of 2003 Apr 24 9397 750 11463 PCA9552_2 PCA9552_2 20030224 Product data 853-2374 29331 of 2002 Dec 20 9397 750 11156 PCA9552_1 PCA9552_1 20020927 Product data 853-2374 28878 of 2002 Sep 09 9397 750 10329 - PCA9552_5 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 05 — 9 March 2006 26 of 28 PCA9552 Philips Semiconductors 16-bit I2C-bus LED driver with programmable blink rates 18. Data sheet status Level Data sheet status [1] Product status [2] [3] Definition I Objective data Development This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. II Preliminary data Qualification This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. III Product data Production This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). [1] Please consult the most recently issued data sheet before initiating or completing a design. [2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. [3] For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. 19. Definitions customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Right to make changes — Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status ‘Production’), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. 21. Trademarks Notice — All referenced brands, product names, service names and trademarks are the property of their respective owners. I2C-bus — logo is a trademark of Koninklijke Philips Electronics N.V. 20. Disclaimers Life support — These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors 22. Contact information For additional information, please visit: http://www.semiconductors.philips.com For sales office addresses, send an email to: [email protected] PCA9552_5 Product data sheet © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Rev. 05 — 9 March 2006 27 of 28 PCA9552 Philips Semiconductors 16-bit I2C-bus LED driver with programmable blink rates 23. Contents 1 2 3 4 5 5.1 5.2 6 6.1 6.2 6.2.1 6.3 6.3.1 6.3.2 6.3.3 6.3.4 6.3.5 6.3.6 6.3.7 6.4 6.5 6.6 7 7.1 7.1.1 7.2 7.3 7.4 8 8.1 8.2 9 10 11 12 13 14 15 15.1 15.2 15.3 15.4 15.5 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4 Functional description . . . . . . . . . . . . . . . . . . . 5 Device address . . . . . . . . . . . . . . . . . . . . . . . . . 5 Control Register . . . . . . . . . . . . . . . . . . . . . . . . 5 Control Register definition . . . . . . . . . . . . . . . . 6 Register descriptions . . . . . . . . . . . . . . . . . . . . 6 INPUT0 - Input register 0 . . . . . . . . . . . . . . . . . 6 INPUT1 - Input register 1 . . . . . . . . . . . . . . . . . 6 PCS0 - Frequency Prescaler 0 . . . . . . . . . . . . . 7 PWM0 - Pulse Width Modulation 0 . . . . . . . . . . 7 PCS1 - Frequency Prescaler 1 . . . . . . . . . . . . . 7 PWM1 - Pulse Width Modulation 1 . . . . . . . . . . 7 LS0 to LS3 - LED selector registers . . . . . . . . . 8 Pins used as GPIOs . . . . . . . . . . . . . . . . . . . . . 9 Power-on reset . . . . . . . . . . . . . . . . . . . . . . . . . 9 External RESET . . . . . . . . . . . . . . . . . . . . . . . . 9 Characteristics of the I2C-bus. . . . . . . . . . . . . 10 Bit transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 START and STOP conditions . . . . . . . . . . . . . 10 System configuration . . . . . . . . . . . . . . . . . . . 10 Acknowledge . . . . . . . . . . . . . . . . . . . . . . . . . 11 Bus transactions . . . . . . . . . . . . . . . . . . . . . . . 12 Application design-in information . . . . . . . . . 13 Minimizing IDD when the I/O is used to control LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Programming example . . . . . . . . . . . . . . . . . . 14 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 15 Static characteristics. . . . . . . . . . . . . . . . . . . . 15 Dynamic characteristics . . . . . . . . . . . . . . . . . 17 Test information . . . . . . . . . . . . . . . . . . . . . . . . 19 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 20 Handling information. . . . . . . . . . . . . . . . . . . . 23 Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Introduction to soldering surface mount packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 23 Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 23 Manual soldering . . . . . . . . . . . . . . . . . . . . . . 24 Package related soldering information . . . . . . 24 16 17 18 19 20 21 22 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . Revision history . . . . . . . . . . . . . . . . . . . . . . . Data sheet status. . . . . . . . . . . . . . . . . . . . . . . Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . Contact information . . . . . . . . . . . . . . . . . . . . 25 26 27 27 27 27 27 © Koninklijke Philips Electronics N.V. 2006 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Date of release: 9 March 2006 Document number: PCA9552_5 Published in The Netherlands