74LVCV2G66 Overvoltage tolerant bilateral switch Rev. 01 — 2 April 2004 Product data sheet 1. General description The 74LVCV2G66 is a high-performance, low-power, low-voltage, Si-gate CMOS device that provides superior performance to most advanced CMOS compatible TTL families. The 74LVCV2G66 provides two single pole, single throw analog or digital switches. Each switch includes an overvoltage tolerant input/output terminal (pin nZ), an output/input terminal (pin nY) and low-power active HIGH enable input (pin nE). The overvoltage tolerant switch terminals allow the switching of signals in excess of VCC. The low-power enable input eliminates the necessity of using current limiting resistors in portable applications when using control logic signals much lower than VCC. These inputs are also overvoltage tolerant. 2. Features ■ Wide supply voltage range from 2.3 V to 5.5 V ■ Ultra low-power operation ■ Very low ON-resistance: ◆ 8.0 Ω (typ) at VCC = 2.7 V ◆ 7.5 Ω (typ) at VCC = 3.3 V ◆ 7.3 Ω (typ) at VCC = 5.0 V. ■ 5 V tolerant input for interfacing with 5 V logic ■ High noise immunity ■ Switch handling capability of 32 mA ■ CMOS low-power consumption ■ Latch-up performance exceeds 250 mA ■ Incorporates overvoltage tolerant analog switch technology ■ Switch accepts voltages up to 5.5 V independent of VCC ■ SOT505-2 and SOT765-1 package ■ Specified from −40 °C to +85 °C and −40 °C to +125 °C. 3. Quick reference data Table 1: Quick reference data GND = 0 V; tr = tf ≤ 2.5 ns; min and max at Tamb = −40 °C to +85 °C; typical at Tamb = 25 °C. Symbol Parameter Conditions Min Typ Max Unit tPZH, tPZL turn-on time E to Y or Z CL = 50 pF; RL = 500 Ω VCC = 3.0 V to 3.6 V 1.0 3.8 7.5 ns VCC = 4.5 V to 5.5 V 1.0 2.7 5.0 ns 74LVCV2G66 Philips Semiconductors Overvoltage tolerant bilateral switch Table 1: Quick reference data …continued GND = 0 V; tr = tf ≤ 2.5 ns; min and max at Tamb = −40 °C to +85 °C; typical at Tamb = 25 °C. Symbol Parameter Conditions tPHZ, tPLZ turn-off time E to Y or Z CL = 50 pF; RL = 500 Ω VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V CI input capacitance CS switch capacitance OFF-state ON-state power dissipation capacitance per switch CPD [1] [2] fi = 10 MHz; VCC = 3.3 V Min Typ Max Unit 1.0 6.5 13.5 ns 1.0 4.4 9.0 ns - 2.5 - pF - 8.0 - pF - 16 - pF - 10.3 - pF [1] CPD is used to determine the dynamic power dissipation (PD in µW). PD = CPD × VCC2 × fi × N where: fi = input frequency in MHz; VCC = supply voltage in V; N = number of inputs. [2] The condition is VI = GND to 5.5 V. 4. Ordering information Table 2: Ordering information Type number Package Temperature range Name Description Version 74LVCV2G66DP −40 °C to +125 °C TSSOP8 plastic thin shrink small outline package; 8 leads; body width 3 mm; lead length 0.5 mm SOT505-2 74LVCV2G66DC −40 °C to +125 °C VSSOP8 plastic very thin shrink small outline package; 8 leads; body width 2.3 mm SOT765-1 5. Marking Table 3: Marking Type number Marking code 74LVCV2G66DP Y66 74LVCV2G66DC Y66 9397 750 13027 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 2 April 2004 2 of 23 74LVCV2G66 Philips Semiconductors Overvoltage tolerant bilateral switch 6. Functional diagram 1Y 1 1Z 7 # 1 1 2 X1 1E 5 2Z 2Y 3 # 1 1 6 X1 001aaa531 2E 001aaa530 Fig 1. Logic symbol. Fig 2. IEC logic symbol. Z Y E VCC 001aaa532 Fig 3. Logic diagram. 7. Pinning information 7.1 Pinning 1Z 1 8 VCC 1Y 2 7 1E 2E 3 6 2Y GND 4 5 2Z 66 001aaa529 Fig 4. Pin configuration. 7.2 Pin description Table 4: Pin description Pin Symbol Description 1 1Z independent input/output (overvoltage tolerance) 2 1Y independent input/output 3 2E enable input (active HIGH) 4 GND ground (0 V) 5 2Z independent input/output (overvoltage tolerance) 9397 750 13027 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 2 April 2004 3 of 23 74LVCV2G66 Philips Semiconductors Overvoltage tolerant bilateral switch Table 4: Pin description …continued Pin Symbol Description 6 2Y independent input/output 7 1E enable input (active HIGH) 8 VCC supply voltage 8. Functional description 8.1 Function table Table 5: Function table [1] Input nE Switch L OFF-state H ON-state [1] H = HIGH voltage level; L = LOW voltage level. 9. Limiting values Table 6: Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Max Unit −0.5 +6.5 V −0.5 +6.5 V VCC supply voltage VI input voltage IIK input diode current VI < −0.5 V or VI > 6.5 V - −50 mA ISK switch diode current VI < −0.5 V or VI > 6.5 V - ±50 mA [1] VS DC switch voltage range enable and disable mode −0.5 +6.5 V IS switch source or sink current VS < −0.5 V or VS > 6.5 V - ±50 mA ICC, IGND VCC or GND current - ±100 mA Tstg storage temperature −65 +150 °C Ptot power dissipation - 300 mW [1] Tamb = −40 ° C to +125 °C The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 9397 750 13027 Product data sheet Min © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 2 April 2004 4 of 23 74LVCV2G66 Philips Semiconductors Overvoltage tolerant bilateral switch 10. Recommended operating conditions Table 7: Recommended operating conditions Symbol Parameter VCC supply voltage VI input voltage Conditions Typ Max Unit 2.3 - 5.5 V 0 - 5.5 V 0 - 5.5 V −40 - +125 °C VS DC switch voltage range Tamb operating ambient temperature tr, tf input rise and fall times VCC = 2.3 V to 2.7 V 0 - 20 ns/V VCC = 2.7 V to 5.5 V 0 - 10 ns/V [1] enable and disable mode [1] Min To avoid drawing VCC current out of terminal nZ when switch current flows in terminal nY, the voltage drop across the bidirectional switch must not exceed 0.4 V. If the switch current flows into terminal nZ, no VCC current will flow out of terminal nY. In this case, there is no limit for the voltage drop across the switch. 11. Static characteristics Table 8: Static characteristics At recommended operating conditions; voltages are referenced to GND (ground 0 V). Symbol Parameter Conditions Min Typ Max Unit HIGH-level input voltage VCC = 2.3 V to 2.7 V 0.6 × VCC - - V VCC = 3.0 V to 3.6 V 2.0 - - V VCC = 4.5 V to 5.5 V 0.55 × VCC - - V LOW-level input voltage VCC = 2.3 V to 2.7 V - - 0.1 × VCC V VCC = 3.0 V to 3.6 V - - 0.5 V VCC = 4.5 V to 5.5 V - - 0.15 × VCC V Tamb = −40 °C to +85 °C [1] VIH VIL ILI input leakage current - ±0.1 ±5 µA IS(OFF) analog switch VS = 0 V or 5.5 V; OFF-state current per VCC = 2.3 V to 5.5 V; channel see Figure 5 [2] - ±0.1 ±10 µA IS(ON) analog switch ON-state current per channel VS = 0 V or 5.5 V; VCC = 2.3 V to 5.5 V; see Figure 6 [2] - ±0.1 ±10 µA ICC quiescent supply current VI = VCC or GND; IO = 0 A; VCC = 5.5 V - 0.1 10 µA ∆ICC additional quiescent VI = VCC − 0.6 V; IO = 0 A; supply current per pin VCC = 3.0 V to 5.5 V - 0.1 5 µA CI input capacitance - 2.5 - pF CS switch capacitance VI = 5.5 V or GND; VCC = 5.5 V OFF-state - 8.0 - pF ON-state - 16 - pF 9397 750 13027 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 2 April 2004 5 of 23 74LVCV2G66 Philips Semiconductors Overvoltage tolerant bilateral switch Table 8: Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground 0 V). Symbol Parameter Conditions Min Typ Max Unit VCC = 2.3 V to 2.7 V 0.6 × VCC - - V VCC = 3.0 V to 3.6 V 2.0 - - V VCC = 4.5 V to 5.5 V 0.55 × VCC - - V VCC = 2.3 V to 2.7 V - - 0.1 × VCC V VCC = 3.0 V to 3.6 V - - 0.5 V VCC = 4.5 V to 5.5 V - - 0.15 × VCC V VI = 5.5 V or GND; VCC = 5.5 V - - ±5 µA - - ±10 µA - - ±10 µA Tamb = −40 °C to +125 °C HIGH-level input voltage VIH LOW-level input voltage VIL input leakage current ILI IS(OFF) analog switch VS = 0 V or 5.5 V; OFF-state current per VCC = 2.3 V to 5.5 V; channel see Figure 5 [2] IS(ON) analog switch ON-state current per channel VS = 0 V or 5.5 V; VCC = 2.3 V to 5.5 V; see Figure 6 [2] ICC quiescent supply current VI = VCC or GND; IO = 0 A; VCC = 5.5 V - - 40 µA ∆ICC additional quiescent VI = VCC − 0.6 V; IO = 0 A; supply current per pin VCC = 3.0 V to 5.5 V - - 50 µA [1] All typical values are measured at Tamb = 25 °C. [2] For overvoltage signals (VS > VCC) the condition VY < VZ must be observed. VCC VCC E VIL IS Y Z IS IS VO VI Z Y VO VI GND GND 001aaa534 001aaa535 VI = GND and VO = GND or 5.5 V. VI = 5.5 V or GND and VO = open circuit Fig 5. Test circuit for measuring switch OFF-state current. Fig 6. Test circuit for measuring switch ON-state current. 9397 750 13027 Product data sheet E VIH © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 2 April 2004 6 of 23 74LVCV2G66 Philips Semiconductors Overvoltage tolerant bilateral switch Table 9: Resistance RON At recommended operating conditions; voltages are referenced to GND (ground 0 V); see test circuit Figure 7. Symbol Parameter Tamb = −40 °C to +85 RON(peak) RON(rail) Conditions Min Typ Max Unit IS = 8 mA; VCC = 2.3 V to 2.7 V - 13 30 Ω IS = 12 mA; VCC = 2.7 V - 10 25 Ω IS = 24 mA; VCC = 3.0 V to 3.6 V - 8.3 20 Ω IS = 32 mA; VCC = 4.5 V to 5.5 V - 7.4 15 Ω IS = 8 mA; VCC = 2.3 V to 2.7 V - 8.5 20 Ω IS = 12 mA; VCC = 2.7 V - 8.0 18 Ω IS = 24 mA; VCC = 3.0 V to 3.6 V - 7.5 15 Ω IS = 32 mA; VCC = 4.5 V to 5.5 V - 7.3 10 Ω °C [1] switch ON-state resistance (peak) switch ON-state resistance (rail) VS = GND to VCC; VI = VIH VS = GND; VI = VIH VS = VCC; VI = VIH RON(flatness) switch ON-resistance (flatness) IS = 8 mA; VCC = 2.3 V to 2.7 V - 8.5 20 Ω IS = 12 mA; VCC = 2.7 V - 7.2 18 Ω IS = 24 mA; VCC = 3.0 V to 3.6 V - 6.5 15 Ω IS = 32 mA; VCC = 4.5 V to 5.5 V - 5.7 10 Ω IS = 8 mA; VCC = 2.5 V - 17 - Ω IS = 12 mA; VCC = 2.7 V - 10 - Ω IS = 24 mA; VCC = 3.3 V - 5 - Ω IS = 32 mA; VCC = 5.0 V - 3 - Ω IS = 8 mA; VCC = 2.3 V to 2.7 V - - 30 Ω IS = 12 mA; VCC = 2.7 V - - 25 Ω IS = 24 mA; VCC = 3.0 V to 3.6 V - - 20 Ω IS = 32 mA; VCC = 4.5 V to 5.5 V - - 15 Ω VS = GND to VCC; VI = VIH; see Figure 9 Tamb = −40 °C to +125 °C RON(peak) RON(rail) switch ON-state resistance (peak) switch ON-state resistance (rail) VS = GND to VCC; VI = VIH VS = GND; VI = VIH IS = 8 mA; VCC = 2.3 V to 2.7 V - - 20 Ω IS = 12 mA; VCC = 2.7 V - - 18 Ω IS = 24 mA; VCC = 3.0 V to 3.6 V - - 15 Ω IS = 32 mA; VCC = 4.5 V to 5.5 V - - 10 Ω IS = 8 mA; VCC = 2.3 V to 2.7 V - - 20 Ω IS = 12 mA; VCC = 2.7 V - - 18 Ω IS = 24 mA; VCC = 3.0 V to 3.6 V - - 15 Ω IS = 32 mA; VCC = 4.5 V to 5.5 V - - 10 Ω VS = VCC; VI = VIH [1] All typical values are measured at Tamb = 25 °C. 9397 750 13027 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 2 April 2004 7 of 23 74LVCV2G66 Philips Semiconductors Overvoltage tolerant bilateral switch 001aaa536 16 RON (Ω) VS VCC = 2.5 V 2.7 V 3.3 V 5.0 V 12 VCC VIH E 8 Z Y IS VI 4 GND 001aaa533 0 0 2 4 6 VI (V) VI = GND to 5.5 V; RON = VS/IS. Fig 7. Test circuit for measuring switch ON-resistance. VI = GND to 5.5 V; Tamb = 25 °C. Fig 8. Typical switch ON-resistance as a function of input voltage. 9397 750 13027 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 2 April 2004 8 of 23 74LVCV2G66 Philips Semiconductors Overvoltage tolerant bilateral switch 001aaa537 16 Tamb = +85 °C +25 °C −40 °C +125 °C RON (Ω) 12 001aaa538 16 RON (Ω) Tamb = +85 °C +25 °C −40 °C +125 °C 12 8 8 4 4 0 0 0 2 4 6 0 2 4 VI (V) 6 VI (V) a. VCC = 2.5 V b. VCC = 2.7 V 001aaa539 16 001aaa540 16 RON (Ω) RON (Ω) Tamb = +85 °C +25 °C −40 °C +125 °C 12 12 8 8 4 4 0 Tamb = +85 °C +25 °C −40 °C +125 °C 0 0 2 4 6 0 2 4 VI (V) c. VCC = 3.3 V 6 VI (V) d. VCC = 5.0 V Fig 9. Switch ON-resistance at various supply voltages as a function of input voltage. 9397 750 13027 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 2 April 2004 9 of 23 74LVCV2G66 Philips Semiconductors Overvoltage tolerant bilateral switch 12. Dynamic characteristics Table 10: Dynamic characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V); test circuit Figure 12. Symbol Parameter Tamb = −40 °C to +85 tPHL, tPLH tPZH, tPZL tPHZ, tPLZ Conditions Min Typ Max Unit - 0.4 1.2 ns VCC = 2.7 V - 0.4 1.0 ns VCC = 3.0 V to 3.6 V - 0.3 0.8 ns VCC = 4.5 V to 5.5 V - 0.2 0.6 ns VCC = 2.3 V to 2.7 V 1.0 4.7 12 ns VCC = 2.7 V 1.0 4.4 8.5 ns VCC = 3.0 V to 3.6 V 1.0 3.8 7.5 ns VCC = 4.5 V to 5.5 V 1.0 2.7 5.0 ns VCC = 2.3 V to 2.7 V 1.0 6.0 16 ns VCC = 2.7 V 1.0 7.9 15 ns VCC = 3.0 V to 3.6 V 1.0 6.5 13.5 ns 1.0 4.4 9.0 ns °C [1] propagation delay nY to nZ see Figure 10 or nZ to nY VCC = 2.3 V to 2.7 V turn-on time E to Y or Z turn-off time E to Y or Z [2] see Figure 11 see Figure 11 VCC = 4.5 V to 5.5 V power dissipation capacitance per switch CPD CL = 50 pF; fi = 10 MHz [3] [4] VCC = 2.5 V - 9.7 - pF VCC = 3.3 V - 10.3 - pF VCC = 5.0 V - 11.3 - pF - - 2.0 ns VCC = 2.7 V - - 1.5 ns VCC = 3.0 V to 3.6 V - - 1.5 ns VCC = 4.5 V to 5.5 V - - 1.0 ns VCC = 2.3 V to 2.7 V 1.0 - 15 ns VCC = 2.7 V 1.0 - 11 ns VCC = 3.0 V to 3.6 V 1.0 - 9.5 ns VCC = 4.5 V to 5.5 V 1.0 - 6.5 ns VCC = 2.3 V to 2.7 V 1.0 - 20 ns VCC = 2.7 V 1.0 - 19 ns VCC = 3.0 V to 3.6 V 1.0 - 17 ns VCC = 4.5 V to 5.5 V 1.0 - 11.5 ns Tamb = −40 °C to +125 °C tPHL, tPLH tPZH, tPZL tPHZ, tPLZ [1] propagation delay nY to nZ see Figure 10 or nZ to nY VCC = 2.3 V to 2.7 V turn-on time E to Y or Z turn-off time E to Y or Z [2] see Figure 11 see Figure 11 All typical values are measured at Tamb = 25 °C. 9397 750 13027 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 2 April 2004 10 of 23 74LVCV2G66 Philips Semiconductors Overvoltage tolerant bilateral switch [2] tPHL and tPLH propagation delay is the calculated RC time constant of the typical ON-state resistance of the switch and the specified capacitance when driven by an ideal voltage source (zero output impedance). [3] CPD is used to determine the dynamic power dissipation (PD in µW). PD = CPD × VCC2 × fi × N where: fi = input frequency in MHz; VCC = supply voltage in V; N = number of inputs. [4] The condition is VI = GND to 5.5 V. 13. Waveforms VI nY or nZ input VM VM GND t PLH t PHL VOH nZ or nY output VM VM VOL 001aaa541 Measurement points are given in Table 11. Logic levels: VOL and VOH are typical output voltage drop that occur with the output load. Fig 10. Input (Y or Z) to output (Z or Y) propagation delays. Table 11: Measurement points Supply voltage Input Output VCC VM VM 2.3 V to 2.7 V 0.5 × VCC 0.5 × VCC 2.7 V 1.5 V 1.5 V 3.0 V to 3.6 V 1.5 V 1.5 V 4.5 V to 5.5 V 0.5 × VCC 0.5 × VCC 9397 750 13027 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 2 April 2004 11 of 23 74LVCV2G66 Philips Semiconductors Overvoltage tolerant bilateral switch VI nE input VM GND t PLZ t PZL VCC nY or nZ output LOW-to-OFF OFF-to-LOW VM VX VOL t PZH t PHZ nY or nZ output HIGH-to-OFF OFF-to-HIGH VOH Vy VM GND switch enabled switch disabled switch enabled 001aaa542 Measurement points are given in Table 12. Logic levels: VOL and VOH are typical output voltage drop that occur with the output load. Fig 11. Turn-on and turn-off times. Table 12: Measurement points Supply voltage Input Output VCC VM VM VX VY 2.3 V to 2.7 V 0.5 × VCC 0.5 × VCC VOL + 0.1 × VCC VOH − 0.1 × VCC 2.7 V 1.5 V 1.5 V VOL + 0.3 V VOH − 0.3 V 3.0 V to 3.6 V 1.5 V 1.5 V VOL + 0.3 V VOH − 0.3 V 4.5 V to 5.5 V 0.5 × VCC 0.5 × VCC VOL + 0.3 V VOH − 0.3 V 9397 750 13027 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 2 April 2004 12 of 23 74LVCV2G66 Philips Semiconductors Overvoltage tolerant bilateral switch VEXT VCC PULSE GENERATOR VI RL VO D.U.T. CL RT RL mna616 Test data is given in Table 13. Definitions test circuit: RT = Termination resistance should be equal to output impedance Zo of the pulse generator. CL = Load capacitance including jig and probe capacitance. RL = Load resistance. VEXT = Test voltage for switching times. Fig 12. Load circuitry for switching times. Table 13: Test data Supply voltage Input Load VCC VI tr, tf 2.3 V to 2.7 V VCC 2.7 V 2.7 V 3.0 V to 3.6 V 4.5 V to 5.5 V CL RL tPLH, tPHL tPZH, tPHZ tPZL, tPLZ ≤ 2.0 ns 30 pF 500 Ω open GND 2 × VCC ≤ 2.5 ns 50 pF 500 Ω open GND 6.0 V 2.7 V ≤ 2.5 ns 50 pF 500 Ω open GND 6.0 V VCC ≤ 2.5 ns 50 pF 500 Ω open GND 2 × VCC 9397 750 13027 Product data sheet VEXT © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 2 April 2004 13 of 23 74LVCV2G66 Philips Semiconductors Overvoltage tolerant bilateral switch 14. Additional dynamic characteristics Table 14: Additional dynamic characteristics At recommended conditions; typical values measured at Tamb = 25 °C. Symbol Parameter Conditions Min Typ Max Unit dsin sine-wave distortion fi = 1 kHz; RL = 10 kΩ; CL = 50 pF; see Figure 13 VCC = 2.3 V - 0.42 - % VCC = 3.0 V - 0.36 - % VCC = 4.5 V - 0.47 - % VCC = 2.3 V - 0.11 - % VCC = 3.0 V - 0.07 - % - 0.01 - % VCC = 2.3 V - 160 - MHz VCC = 3.0 V - 200 - MHz VCC = 4.5 V - 210 - MHz VCC = 2.3 V - 180 - MHz VCC = 3.0 V - 180 - MHz - 180 - MHz VCC = 2.3 V - −65 - dB VCC = 3.0 V - −65 - dB - −62 - dB VCC = 2.3 V - −37 - dB VCC = 3.0 V - −36 - dB VCC = 4.5 V - −36 - dB VCC = 2.3 V - 91 - mV VCC = 3.0 V - 119 - mV VCC = 4.5 V - 205 - mV fi = 10 kHz; RL = 10 kΩ; CL = 50 pF; see Figure 13 VCC = 4.5 V fON-state(res) switch ON-state signal frequency response RL = 600 Ω; CL = 50 pF; fi = 1 MHz; see Figure 14 RL = 50 Ω; CL = 5 pF; fi = 1 MHz; see Figure 14 [1] [1] VCC = 4.5 V αOFF(ft) switch OFF-state signal feed-through attenuation RL = 600 Ω; CL = 50 pF; fi = 1 MHz; see Figure 15 [2] VCC = 4.5 V RL = 50 Ω; CL = 5 pF; fi = 1 MHz; see Figure 15 Vct(ctl-sw) crosstalk between control input to signal output RL = 600 Ω; CL = 50 pF; fi = 1 MHz; tr = tf = 2 ns; see Figure 16 9397 750 13027 Product data sheet [2] © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 2 April 2004 14 of 23 74LVCV2G66 Philips Semiconductors Overvoltage tolerant bilateral switch Table 14: Additional dynamic characteristics …continued At recommended conditions; typical values measured at Tamb = 25 °C. Symbol Parameter Conditions Min Typ Max Unit Vct(sw-sw) crosstalk between switches RL = 600 Ω; CL = 50 pF; fi = 1 MHz; see Figure 17 VCC = 2.3 V - −56 - dB VCC = 3.0 V - −55 - dB VCC = 4.5 V - −55 - dB VCC = 2.3 V - −29 - dB VCC = 3.0 V - −28 - dB VCC = 4.5 V - −28 - dB VCC = 2.5 V - <0.003 - pC VCC = 3.3 V - 0.003 - pC VCC = 4.5 V - 0.0035 - pC VCC = 5.5 V - 0.0035 - pC RL = 50 Ω; CL = 5 pF; fi = 1 MHz; see Figure 17 Q [1] injection charge CL = 0.1 nF; Vgen = 0 V; Rgen = 0 Ω; f = 1 MHz; RL = 1 MΩ; see Figure 18 Adjust fi voltage to obtain 0 dBm level at output. Increase fi frequency until dB meter reads −3 dB. [2] Adjust fi voltage to obtain 0 dBm level at input. [3] Definition: Q = ∆Vout × CL. Guaranteed by design. 0.5VCC VCC RL VIH E Y or Z fi Z or Y 600 Ω 10 µF CL D GND 001aaa544 Test conditions: VCC = 2.3 V: Vi = 2 V (p-p). VCC = 3 V: Vi = 2.5 V (p-p). VCC = 4.5 V: Vi = 4 V (p-p). Fig 13. Test circuit for measuring sine-wave distortion. 9397 750 13027 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 2 April 2004 15 of 23 74LVCV2G66 Philips Semiconductors Overvoltage tolerant bilateral switch 0.5VCC VCC RL VIH 0.1 µF fi E Y or Z Z or Y 50 Ω CL dB GND 001aaa543 Fig 14. Test circuit for measuring the frequency response when switch is in ON-state. 0.5VCC 0.5VCC VCC RL RL VIL 0.1 µF fi E Y or Z Z or Y 50 Ω CL dB GND 001aaa545 Fig 15. Test circuit for measuring feed-through attenuation when switch is in OFF-state. 0.5VCC 0.5VCC VCC Ri = 600 Ω RL = 600 Ω E Y or Z logic input Z or Y CL = 50 pF 50 Ω VO GND 001aaa546 Fig 16. Test circuit for measuring crosstalk between control input and output. 9397 750 13027 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 2 April 2004 16 of 23 74LVCV2G66 Philips Semiconductors Overvoltage tolerant bilateral switch 0.5VCC 1E VIH 0.1 µF Ri RL 1Y or 1Z 1Z or 1Y 600 Ω fi 50 Ω CL 50 pF VO1 channel ON 0.5VCC 2E VIL RL 2Y or 2Z 2Z or 2Y Ri 600 Ω CL 50 pF VO2 channel OFF 001aaa547 20 log10 (VO2/VO1) or 20 log10 (VO1/VO2). Fig 17. Test circuit for measuring crosstalk between switches. VCC E Y or Z Z or Y Rgen logic input RL = 1 MΩ Vgen CL = 0.1 nF VO GND 001aaa548 logic (E) off input on VO off ∆ VOUT 001aaa549 Fig 18. Test circuit for measuring injection charge. 9397 750 13027 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 2 April 2004 17 of 23 74LVCV2G66 Philips Semiconductors Overvoltage tolerant bilateral switch 15. Application information Use the 74LVCV2G66 to reduce component count and footprint in low-power portable applications. Typical ‘66’ devices do not have low-power enable inputs causing a high ∆ICC. To reduce power consumption in portable (battery) applications, a current limiting resistor is used. (see Figure 19a). The low-power enable inputs of the 74 LVCV2G66 have much lower ∆ICC, eliminating the necessity of the current limiting resistor (see Figure 19b). 5V 5V 1 MΩ VCC 3V VCC E 3V Z Y '66' device (a) E Z Y 74LVCV2G66 (b) 001aaa550 Fig 19. Application example. 9397 750 13027 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 2 April 2004 18 of 23 74LVCV2G66 Philips Semiconductors Overvoltage tolerant bilateral switch 16. Package outline TSSOP8: plastic thin shrink small outline package; 8 leads; body width 3 mm; lead length 0.5 mm D E A SOT505-2 X c HE y v M A Z 5 8 A A2 (A3) A1 pin 1 index θ Lp L 1 4 e detail X w M bp 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D(1) E(1) e HE L Lp v w y Z(1) θ mm 1.1 0.15 0.00 0.95 0.75 0.25 0.38 0.22 0.18 0.08 3.1 2.9 3.1 2.9 0.65 4.1 3.9 0.5 0.47 0.33 0.2 0.13 0.1 0.70 0.35 8° 0° Note 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. OUTLINE VERSION REFERENCES IEC SOT505-2 JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 02-01-16 --- Fig 20. Package outline TSSOP8. 9397 750 13027 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 2 April 2004 19 of 23 74LVCV2G66 Philips Semiconductors Overvoltage tolerant bilateral switch VSSOP8: plastic very thin shrink small outline package; 8 leads; body width 2.3 mm D E SOT765-1 A X c y HE v M A Z 5 8 Q A A2 A1 pin 1 index (A3) θ Lp 1 4 e L detail X w M bp 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D(1) E(2) e HE L Lp Q v w y Z(1) θ mm 1 0.15 0.00 0.85 0.60 0.12 0.27 0.17 0.23 0.08 2.1 1.9 2.4 2.2 0.5 3.2 3.0 0.4 0.40 0.15 0.21 0.19 0.2 0.13 0.1 0.4 0.1 8° 0° Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION REFERENCES IEC SOT765-1 JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 02-06-07 MO-187 Fig 21. Package outline VSSOP8. 9397 750 13027 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 2 April 2004 20 of 23 74LVCV2G66 Philips Semiconductors Overvoltage tolerant bilateral switch 17. Revision history Table 15: Revision history Document ID Release date Data sheet status Change notice Order number Supersedes 74LVCV2G66_1 20040402 Product data sheet - 9397 750 13027 - 9397 750 13027 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 2 April 2004 21 of 23 74LVCV2G66 Philips Semiconductors Overvoltage tolerant bilateral switch 18. Data sheet status Level Data sheet status [1] Product status [2] [3] Definition I Objective data Development This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. II Preliminary data Qualification This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. III Product data Production This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). [1] Please consult the most recently issued data sheet before initiating or completing a design. [2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. [3] For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. 19. Definitions 20. Disclaimers Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Life support — These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Right to make changes — Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status ‘Production’), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. 21. Contact information For additional information, please visit: http://www.semiconductors.philips.com For sales office addresses, send an email to: [email protected] 9397 750 13027 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 01 — 2 April 2004 22 of 23 74LVCV2G66 Philips Semiconductors Overvoltage tolerant bilateral switch 22. Contents 1 2 3 4 5 6 7 7.1 7.2 8 8.1 9 10 11 12 13 14 15 16 17 18 19 20 21 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Quick reference data . . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional description . . . . . . . . . . . . . . . . . . . 4 Function table . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4 Recommended operating conditions. . . . . . . . 5 Static characteristics. . . . . . . . . . . . . . . . . . . . . 5 Dynamic characteristics . . . . . . . . . . . . . . . . . 10 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Additional dynamic characteristics . . . . . . . . 14 Application information. . . . . . . . . . . . . . . . . . 18 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 19 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 21 Data sheet status . . . . . . . . . . . . . . . . . . . . . . . 22 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Contact information . . . . . . . . . . . . . . . . . . . . 22 © Koninklijke Philips Electronics N.V. 2004 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Date of release: 2 April 2004 Document order number: 9397 750 13027 Published in The Netherlands