Teccor® brand Protection Thyristors Axial Leaded DO-41 Series SIDACtor® Device Description This DO-41 plastic package provides a through-hole version of the SIDACtor® devices. This axial leaded device is ideal for Customer Premises Equipment (CPE) such as telephones, answering machines, modems, and fax interfaces. The DO-41 package series can also be used for overvoltage protection for applications such as T1/E1/J1 trunk cards when the appropriate overcurrent protection is included. Features •R oHS compliant • Bidirectional transient voltage protection • Axial lead through-hole component • Teccor brand SIDACtor technology Agency Approvals Agency Agency File Number E133083 Protection solution to meet •Y D/T 950 • YD/T 993 • YD/T 1082 •G R 1089 Intra-building • IEC 61000-4-5 • ITU K.20/21 Basic Level • TIA-968-A Type B Surges Electrical Characteristics VDRM @lDRM=5µA VS @100V/µs Volts Volts IH IS IT VT @IT=1 amp Capacitance @1MHz, 2V bias Amps Volts pF Part Number Marking Min Max Min Max Max Max Typical P1100THLRP P11H 90 130 150 800 1.0 5 60 P1300THLRP P13H 120 160 150 800 1.0 5 40 P1500THLRP P15H 140 180 150 800 1.0 5 40 mAmps mAmps P1800THLRP P18H 170 220 150 800 1.0 5 40 P2300THLRP P23H 190 260 150 800 1.0 5 30 P2600THLRP P26H 220 300 150 800 1.0 5 30 P3100THLRP P31H 275 350 150 800 1.0 5 30 P3500THLRP P35H 320 400 150 800 1.0 5 30 • All measurements are made at an ambient temperature of 25°C. • Listed SIDACtor devices are bidirectional. All electrical parameters and surge ratings apply to forward and reverse polarities. DO-41 Series Specifications are subject to change without notice. Telecom Design Guide www.littelfuse.com ©2006 Littelfuse Teccor® brand Protection Thyristors Axial Leaded Surge Ratings IPP Series 5x320 µs 10x1000 µs Amps Amps Min Min 25 35 H • IPP applies to -40°C through +85°C temperature range. • IPP is a repetitive surge rating and is guaranteed for the life of the product. V-I Characteristics tr x td Pulse Waveform IT IS IH IDRM -V +V VT VDRM VS IPP – Peak Pulse Current – %IPP +I 100 50 0 IH (TC = 25 ˚C) IH 6 25 ˚C 4 2 0 -4 -6 -8 -40 -20 0 Junction Temperature (TJ) – ˚C Specifications are subject to change without notice. td t – Time (µs) 2.0 1.8 1.6 1.4 25 ˚C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) – ˚C 20 40 60 80 100 120 140 160 DO-41 Series tr Normalized DC Holding Current Versus Case Temperature Ratio of Percent of VS Change – % 8 Half Value 0 14 12 10 tr = rise time to peak value td = decay time to half value Waveform = tr x td -I Normalized VS Change Versus Junction Temperature Peak Value Telecom Design Guide www.littelfuse.com ©2006 Littelfuse Teccor® brand Protection Thyristors Axial Leaded Soldering Parameters Pb – Free assembly Reflow Condition Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 190°C - Time (min to max) (ts) 50 – 150 seconds Average ramp up rate (Liquidus Temp (TL) to peak) 5°C/second max TS(max) to TL - Ramp-up Rate 5°C/second max Reflow - Temperature (TL) (Liquidus) 220°C - Time (min to max) (ts) >60 – <150 seconds Peak Temperature (TP) 250+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 5°C/second max Time 25°C to peak Temperature (TP) 8 minutes max. Do not exceed 280°C Physical Specifications Environmental Specifications Terminal Material Matte Tin-plated Axial leads Operating/Storage Temperature -40° C to ~ +150°C Lead Solderability MIL-STD-750, Method 2026 Passive Aging 125° C, 1000 hours Meet Spec Humidity Aging +85°C, 85% R.H. 1000 hours Meet Spec Thermal Shock MIL-STD-202 Method 107G +85°C/-40°C 100 times Meet Spec Solvent Resistance MIL-STD-202, Method 215 No Change Vibration MIL-STD-883C, Method 2007.1, Condition A No Change Dimensions [25.40] 1.000 MIN [0.86] .034 [0.71] .028 (2.72) .107 [2.00] .080 [5.21] .205 [4.10] .160 [25.40] 1.000 MIN Dimensions in inches and (millimeters) DO-41 SERIES DO-41 Series Specifications are subject to change without notice. Telecom Design Guide www.littelfuse.com ©2006 Littelfuse Teccor® brand Protection Thyristors Axial Leaded Part Marking System XXXX Part Numbering System Pxxx0 T H LRP XXXX First Line: Product Name (see marking column in table on page 1) PACKING STYLE RP : Reel Pack per EIA RS-296 DEVICE TYPE P : SIDACtor Second Line: Lot number MEDIAN VOLTAGE xxx : xxx volts CONSTRUCTION VARIATION 0 : Single SIDACtor chip used as a single device L : RoHS Compliant SURGE IPP Rating H : 35A 10/1000µs PACKAGE TYPE T : DO-41 Packaging Package Type Description Packing Quantity Added Suffix Industry Standard DO-41 Axial 5000 RP EIA RS-296 Tape and Reel Specification Symbol Case Type Inches MM A Component Spacing (lead to lead) 0.200 ± 0.020” 5.08 ± 0.508 B Tape Spacing 2.062 ± 0.059” 52.37 ± 1.498 C Tape Width 0.250” 6.35 D Max. Off Alignment 0.048” 1.219 E Reel Dimension 13” 330.2 F Max Hub Recess 3” 76.19 G Max. Abor Hole 0.68” 17.27 H Reel Dimension 2.75” 69.85 B OFF CENTER BOTH SIDES (±0.039") OVERALL LENGTH A OFF CENTER BOTH SIDES (±0.039") OVERALL LENGTH B C A D C D H H recess depth max 0.75” recess depth max 0.75” F F E E G G LABEL LABEL DO-41 Series Specifications are subject to change without notice. Telecom Design Guide www.littelfuse.com ©2006 Littelfuse