V23809-F7-C10 Multimode 1300 nm LED Fibre Channel 266 MBd Transceiver* Dimensions in (mm) inches (8.6 max) .170 max (10 max) PC board .393 max thickness View Z (Lead cross section and standoff size) (0.63 ±0.2) .025 ±.008 (3 ±0.2) .118 ±.008 (0.6 ±0.1) .024 ±.004 11x (0.3 ±0.02) .012 ±.001 8x 2.54=20.32 8x .100 =.800 A ∅0.1 M ∅.004 M 2x (1.4 –0.05) (2.8 max) .055 –.002 .110 max Z (25.25 ±0.05) .994 ±.002 11x 5.2 .205 ∅0.3 M A ∅.012 M A 1 2 3 4 5 6 7 8 9 ∅0.3 M A ∅.012 M A .031 ±.004 (3.8 max) (0.7 ±0.1) .150 max .028 ±.004 PC board ∅0.1 M ∅.004 M 9x 9x (0.8 ±0.1) Optical Centerline (2) .080 (1 ±0.1) .04 ±.039 Top view 8x 2.54=20.32 8x .100 =.800 Rx DUPLEX SC RECEPTACLE 12.7 .500 Tx 20.32 .800 (15.88 ±0.5) .625 ±.020 (2.54) .100 (2.54) .100 (11 max) .433 max 20.32 .800 (1.9 ±0.1) 2x .075 ±.004 Footprint (38.6 ±0.15) 1.52 ±.006 APPLICATIONS • FC fabric point-to-point links • HIPPI, SCSI, IPI • High speed computer links • Local area networks up to 320 MBd • High definition digital television • Switching systems Absolute Maximum Ratings Exceeding any one of these values may destroy the device immediately. FEATURES • Fully compliant with all major standards • Compact integrated transceiver unit with duplex SC receptacle • Single power supply with 3.0 V to 5.5 V range • Extremely low power consumption < 0.7 W at 3.3 V • PECL differential inputs and outputs • System is optimized for 62.5/50 µm graded index fiber • Industry standard multisource footprint • Very low profile for high slot density • Process plug included • Wave solderable and washable with process plug inserted • Testboard available • UL-94 V-0 certified Supply Voltage (VCC–VEE).......................................... –0.5 to 7 V Data Input Levels (PECL) (VIN) .................................. VEE to VCC Differential Data Input Voltage (∆VIN).................................. 3.0 V Operating Ambient Temperature (TAMB) .................0°C to 85°C Storage Ambient Temperature (TSTG).................. –40°C to 85°C Humidity/Temperature Test Condition (RH)................. 85%/85°C Soldering Conditions, Temp/Time (TSOLD/tSOLD) (MIL-STD 883C, Method 2003) .............................. 270°C/10 s ESD Resistance (all pins to VEE, human body) .................. 1.5 kV Output Current (IO) ........................................................... 50 mA * Available also as FC 133 MBd V23809-B7-C10 on request Fiber Optics JULY 1999 DESCRIPTION Recommended Operating Conditions This data sheet describes the Infineon Fibre Channel transceiver, which belongs to the Infineon Multistandard Transceiver Family. It is fully compliant with the Fibre Channel FC-133 MBaud and FC-266 MBaud draft standard. Parameter Fibre Channel provides a general transport for upper layer protocols such as Intelligent Peripheral Interface (IPI), High Performance Parallel Interface (HIPPI) and Small Computer System Interface (SCSI) command sets. Defined transmission rates are 266 MBaud and 133 MBaud in point-to-point or fabric topology. Symbol Min. Typ. Max. Ambient Temperature TAMB 0 70 °C Power Supply Voltage VCC–VEE 3 5.5 V Supply Current 3.3 V ICC 230 mA Supply Current 5 V(1) Units 260 Transmitter Data Input High Voltage VIH–VCC –1165 –880 The Infineon low cost multistandard transceiver is a single unit comprised of a transmitter, a receiver, and an SC receptacle. This design frees the customer from many alignment and PC board layout concerns. The modules are designed for low cost applications. Data Input Low Voltage VIL–VCC –1810 –1475 Threshold Voltage VBB–VCC –1380 –1260 Input Data Rise/Fall Time, 20%–80% tR, tF 1.3 The inputs/outputs are PECL compatible, and the unit operates from a 3.0 V to 5.5 V power supply. As an option, the data output stages can be switched to static levels during absence of light as indicated by the Signal Detect function. It can be directly interfaced with available chipsets. Data High Time(2) tON 1000 Output Current IO 25 mA Input Duty Cycle Distortion tDCD 1 ns Input Data Dependent Jitter tDDJ 1 Feature Standard Comments Electromagnetic Interference (EMI) FCC Class B EN 55022 Class B CISPR 22 Noise frequency range:30 MHz to 1 GHz Input Random Jitter tRJ Input Center Wavelength λC Immunity: Electrostatic Discharge EN 61000-4-2 IEC 1000-4-2 Discharges of ± 15kV with an air discharge probe on the receptacle cause no damage. Electrical Output Load(3) RL EN 61000-4-3 IEC 1000-4-3 Eye Safety IEC 825-1 ns Receiver Regulatory Compliance Immunity: Radio Frequency Electromagnetic Field 0.4 mV 0.76 1260 1380 50 nm Ω Notes 1. For VCC–VEE (min., max.). 50% duty cycle. The supply current (ICC2+ICC3) does not include the load drive current (ICC1). Add max. 45 mA for the three outputs. Load is 50 Ω to VCC–2 V. With a field strength of 10 V/m rms, noise frequency ranges from 10 MHz to 1 GHz 2. To maintain good LED reliability, the device should not be held in the ON state for more than the specified time. Normal operation should be done with 50% duty cycle. 3. To achieve proper PECL output levels the 50 Ω termination should be done to VCC–2 V. For proper termination see the application notes. Class 1 TECHNICAL DATA The electro-optical characteristics described in the following tables are valid only for use under the recommended operating conditions. Semiconductor Group V23809-F7-C10, Multimode 1300 nm LED Fibre Channel 266 MBd Transceiver 2 Transmitter Electro-Optical Characteristics Receiver Electro-Optical Characteristics (Values in brackets are for 320 MBd) Transmitter Symbol Min. (Values in brackets are for 320 MBd) Typ. Max. Units Receiver 266 mBaud (320) Symbol Min. Data Rate DR 5(1) Sensitivity (Average Power)(2) PIN Saturation (Average Power)(3) PSAT Deterministic Jitter(4, 5) Typ. Max. Units 266 (320) mBaud –26 dBm tDJ 19 % Random Jitter(4, 6) tRJ 9 Signal Detect Assert Level(7) PSDA –43.5 –29 –30.5 Data Rate DR 0 Launched Power (Average)(1, 2) into 62.5 µm Fiber PO –20 –16 –14 (–21) (–17) Center Wavelength(2, 3) λC 1280 Spectral Width (FWHM)(2, 4) ∆l Output Rise Time, 10%–90%(5) tR Output Rise Time, 10%–90%(5) tF 2.2 (2.5) TCp .03 dB/°C Signal Detect Deassert Level(8) PSDD –45 Temperature Coefficient of Optical Output Power ER 12 % Signal Detect Hysteresis PSDA– PSDD 1.5 Extinction Ratio (Dynamic)(2, 6) tDJ 16 Output Low Voltage(9) VOL–VCC –1810 –1620 mV Deterministic Jitter(7, 8) Random Jitter(7, 9) tRJ 9 Output High Voltage(9) VOH–VCC –1025 –880 Output Data Rise/Fall Time, 20%–80% t ,t 1.3 dBm 1380 nm 200 0.6 2.0 (2.5) ns Notes 1. Measured at the end of 5 meters of 62.5/125/0.275 graded index fiber using calibrated power meter and a precision test ferrule. Cladding modes are removed. Values valid for EOL. –30 –14 –11 dB ns R F Output SD Rise/Fall Time, 20%–80% 2. The input data pattern is a 12.5 MHz square wave pattern. dBm 40 3. Center wavelength is defined as the midpoint between the two 50% levels of the optical spectrum of the LED. Notes 4. Spectral width (full width, half max.) is defined as the difference between 50% levels of the optical spectrum of the LED. 2. For a bit error rate (BER) of less than 1x10E-12 over a receiver eye opening of least 1.0ns. Measured with a 27–1 PRBS. 5. 10% to 90% levels. Measured using a 12.5 MHz square wave pattern with an optoelectronic measurement system (detector and oscilloscope) with 3 dB bandwidth ranging from less than 0.1 MHz to more than 750 MHz. 3. For a BER of less than 1x10E-12. Measured in the center of the eye opening with a 27–1 PRBS. 1. Pattern: Manchester coding / NRZI (no scrambling) 4. Test method and considerations as in FH-PC Appendix A. 5. Measured with the K28.5 pattern from Chapter II of the FC-PH at 266 MBd. 6. Extinction ratio is defined as PL/PH x 100%. Measurement system as in Note 5. 6. Measured with the K28.7 pattern from Chapter II of the FC-PH which equals a 133 MHz square wave. 7. Test method and consideration as in FC-PH Appendix A. 8. Measured with the K28.5 pattern from Chapter II of the FC-PH at 266MBd. 7. An increase in optical power through the specified level will cause the Signal Detect output to switch from a Low state to a High state. 9. Measured with the K28.7 pattern from Chapter II of the FC-PH which equals a 133 MHz square wave. 8. A decrease in optical power through the specified level will cause the Signal Detect output to switch from a High state to a Low state. 9. PECL compatible. Load is 50 Ω into VCC–2 V. Measured under DC conditions. For dynamic measurements a tolerance of 50 mV should be added for VCC=5 V. Fiber Optics V23809-F7-C10, Multimode 1300 nm LED Fibre Channel 266 MBd Transceiver 3 Pin Description for 1x9 Pin Row Pin Name Level Pin # Description RxVEE Rx Ground Power Supply 1 Negative power supply, normally ground RxD Rx Output Data PECL Output 2 Receiver output data RxDn Rx Output Data PECL Output 3 Inverted receiver output data Rx SD RX Signal Detect PECL Output active high 4 A high level on this output shows that an optical signal is applied to the optical input RxVCC Rx +3.3...5 V Power Supply 5 Positive power supply, +3.3...5 V TxVCC Tx +3.3...5 V Power Supply 6 Positive power supply, +3.3...5 V TxDn Tx Input Data PECL Input 7 Inverted transmitter input data TxD Tx Input Data PECL Input 8 Transmitter input data TxVEE Tx Ground Power Supply 9 Negative power supply, normally ground Case Support Not Connected S1/S2 Support stud, not connected APPLICATION NOTE FOR 1X9 PIN ROW TRANSCEIVER VCC–TX C1/3=4700 nF (optional) C2/4=4700 nF L1/2=15000 nH (L2 is optional) GND R3 GND TXD TXDN VCC-TX R9 R6 GND GND R in OHM 5 V 4 V 3.3 V R1/3 82 R2/4 130 100 83 R5/7 82 R6/8 130 100 83 GND GND VCC–TX L2 C4 R8 VCC-RX Transceiver C2 C3 200R R4 C1 R7 R5 RD RDN SD R2 VCC–RX VCC 1 9 R1 VCC L1 VCC–RX GND GND GND GND GND DC coupling between ECL gates. 100 127 100 127 R9=200 Ohm The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module VCC–RX/VCC–TX. A GND plane under the module is recommended for good EMI and sensitivity performance. Fiber Optics V23809-F7-C10, Multimode 1300 nm LED Fibre Channel 266 MBd Transceiver 4 APPLICATION NOTE FOR MULTIMODE 1300 NM LED TRANSCEIVER Solutions for connecting a Infineon 3.3 V Fiber Optic Transceiver to a 5.0 V Framer-/Phy-Device. Figure 1. Common GND Figure 1a. Circuitry for SD (Differential) and Common GND VCC 5.0 V VCC 3.3 V VCC 39K 127 VCC VCC 5.0 V 26K VCC 100 nF Framer/Phy Clock Data Recovery Out Tx In 83 500 100 nF 500 Rx Out 127 Data In 180 VCC 68 VCC 3.3 V SD Infineon Fiber Optic 3.3 V Transceiver 83 Framer/Phy SD Clock Recovery 5V SD Figure 1b. Circuitry for SD (Single Ended) and Common GND VCC 5.0 V VCC 3.3 V SD Out VCC VCC 18K SD In Infineon Fiber Optic Transceiver 1.8 V Inputs and outputs are differential and should be doubled. Signal Detect (SD) is single ended (if used). SD In 1 SD Infineon Out Fiber Optic 3.3 V Transceiver 510 Framer/Phy Clock Recovery 5V 1 Zener-Diode 1.8 V Figure 2. Common VCC Framer/Phy Clock Data Recovery Out Infineon Fiber Optic Transceiver GND 3.3 V Tx In 130 Inputs and outputs are differential and should be doubled. Signal Detect (SD) is single ended. VCC Rx Out 83 Data In 82 VCC 127 VCC SD GND 5.0 V In 200 SD Out GND 5.0 V GND 3.3 V GND 3.3 V Infineon Technologies AG i. Gr. • Fiber Optics • Wernerwerkdamm 16 • Berlin D-13623, Germany Infineon Technologies, Corp. • Fiber Optics • 19000 Homestead Road • Cupertino, CA 95014 USA Siemens K.K. • Fiber Optics • Takanawa Park Tower • 20-14, Higashi-Gotanda, 3-chome, Shinagawa-ku • Tokyo 141, Japan www.infineon.com/fiberoptics