INFINEON V23809-F7-T10

V23809-F7-T10
Multimode 1300 nm LED Fibre Channel
266 MBd 1x9 Transceiver with ST Connector
Dimensions in (mm) inches
(1) .039
(1.4)
A
1
(0.6)
.024
(2.8)
max.
.11
max.
bottom
view
(25.4) max.
1 max.
(2.54)
.1
(12.7)
.5
(20.32)
8
9
(0.3) .012 x.012 x 9
∅(0.3) M A M
(3.8) .15 max.
2x ∅(1.4)
∅.055
∅(0.1) M A M
(9.8) max.
.39 max.
(5.27) .207
(14.4) .567
(20.32) .8
(18.47) .727
(41.2) 1.622
FEATURES
• Compliant with Fibre Channel standard
• Meets mezzanine standard height of 9.8 mm
• Compact integrated transceiver unit with duplex ST
receptacle
• Single power supply with 3.0 V to 5.5 V range
• Extremely low power consumption < 0.7 W at 3.3 V
• PECL differential inputs and outputs
• System is optimized for 62.5/50 µm graded index fiber
• Industry standard multisource footprint
• Very low profile for high slot density
• Testboard available
• UL-94 V-0 certified
APPLICATIONS
• FC fabric point-to-point links
• HIPPI, SCSI, IPI
• High speed computer links
• Local area networks
• High definition digital television
• Switching systems
(3±0.2)
.118±.008
V
FC-223809-F
66 M 7-T1
Bd-T 0
RX
Absolute Maximum Ratings
Exceeding any one of these values may destroy the device
immediately.
Supply Voltage (VCC–VEE).......................................... –0.5 to 7 V
Data Input Levels (PECL) (VIN) .................................. VEE to VCC
Differential Data Input Voltage (∆VIN)..................................... 3 V
Operating Ambient Temperature (TAMB).............. 0°C to 85°C
Storage Ambient Temperature (TSTG).................. –40°C to 85°C
Humidity/Temperature Test Condition (RH)................. 85%/85°C
Soldering Conditions, Temp/Time (TSOLD/tSOLD)
(MIL-STD 883C, Method 2003) .............................. 270°C/10 s
ESD Resistance (all pins to VEE, human body) .................. 1.5 kV
Output Current (IO) ........................................................... 50 mA
ST is a registered trademark of AT&T
Fiber Optics
JULY 1999
DESCRIPTION
TECHNICAL DATA
The electro-optical characteristics described in the following
tables are valid only for use under the recommended operating
conditions.
This data sheet describes the Infineon Fibre Channel transceiver, which belongs to the Infineon Multistandard Transceiver
Family. It is fully compliant with the Fibre Channel FC-133
MBaud and FC-266 MBaud standard.
Recommended Operating Conditions
Fibre Channel provides a general transport for upper layer protocols such as Intelligent Peripheral Interface (IPI), High Performance Parallel Interface (HIPPI) and Small Computer System
Interface (SCSI) command sets. Defined transmission rates are
266 MBaud and 133 MBaud in point-to-point or fabric topology.
The Infineon low cost multistandard transceiver is a single unit
comprised of a transmitter, a receiver, and an ST receptacle.
This design frees the customer from many alignment and PC
board layout concerns. The modules are designed for low cost
applications.
Parameter
Symbol
Min.
Ambient Temperature
TAMB
0
70
°C
Power Supply Voltage
VCC–VEE
3
5.5
V
Supply Current 3.3 V
ICC
230
mA
Supply Current 5
Typ. Max.
V(1)
Units
260
Transmitter
The inputs/outputs are PECL compatible, and the unit operates
from a 3.0 V to 5.5 V power supply. As an option, the data output
stages can be switched to static levels during absence of light
as indicated by the Signal Detect function. It can be directly interfaced with available chipsets.
Regulatory Compliance
Data Input
High Voltage
VIH–VCC
–1165
–880
Data Input
Low Voltage
VIL–VCC
–1810
–1475
Threshold Voltage
VBB–VCC –1380
–1260
Input Data Rise/Fall
Time, 20%–80%
tR, tF
1.3
Data High Time(2)
tON
1000
0.4
mV
ns
Receiver
Feature
Standard
Comments
Output Current
IO
25
mA
Electromagnetic
Interference (EMI)
FCC Class B
EN 55022 Class B
CISPR 22
Noise frequency
range: 30 MHz to
1 GHz
Input Duty Cycle
Distortion
tDCD
1
ns
Immunity:
Electrostatic
Discharge
EN 61000-4-2
IEC 1000-4-2
Discharges of
± 15kV with an air
discharge probe on
the receptacle cause
no damage.
Input Data
Dependent Jitter
tDDJ
1
Input Random Jitter
tRJ
0.76
Input Center
Wavelength
λC
Electrical
Output Load(3)
RL
Immunity:
Radio Frequency
Electromagnetic
Field
EN 61000-4-3
IEC 1000-4-3
Eye Safety
IEC 825-1
With a field strength
of 10 V/m rms, noise
frequency ranges
from 10 MHz to
1 GHz
1260
1380
50
nm
Ω
Notes
1. For VCC–VEE (min., max.). 50% duty cycle. The supply current
(ICC2+ICC3) does not include the load drive current (ICC1). Add max.
45 mA for the three outputs. Load is 50 Ω to VCC–2 V.
Class 1
2. To maintain good LED reliability, the device should not be held in the
ON state for more than the specified time. Normal operation should
be done with 50% duty cycle.
3. To achieve proper PECL output levels the 50 Ω termination should
be done to VCC–2 V. For correct termination see the application
notes.
Fiber Optics
V23809-F7–T10, MM 1300 nm LED Fibre Channel 1x9 Transceiver (ST)
2
Transmitter Electro-Optical Characteristics
Transmitter
Symbol Min.
Typ.
Receiver Electro-Optical Characteristics
Max. Units
Data Rate
DR
0
Launched Power
(Average)(1, 2)
into 62.5 µm Fiber
PO
–20
Center Wavelength(2, 3)
λC
1280
Spectral Width
(FWHM)(2, 4)
∆l
Output Rise Time,
10%–90%(5)
tR
Output Rise Time,
10%–90%(5)
tF
2.2
Temperature Coefficient
of Optical Output Power
TCp
0.03
Extinction Ratio
(Dynamic)(2, 6)
ER
12
Deterministic Jitter(7, 8)
tDJ
16
Random Jitter(7, 9)
tRJ
9
–16
Receiver
Min.
5(1)
Typ.
Max.
Units
266
MBaud
–30
–26
dBm
19
%
266
MBaud
Data Rate
DR
–14
dBm
Sensitivity
(Average Power)(2)
PIN
Saturation
(Average Power)(3)
PSAT
Deterministic
Jitter(4, 5)
tDJ
Random Jitter(4, 6)
tRJ
Signal Detect
Assert Level(7)
PSDA
–43.5
–29
Signal Detect
Deassert Level(8)
PSDD
–45
–30.5
dB/°C
Signal Detect
Hysteresis
PSDA–
PSDD
1.5
%
Output Low
Voltage(9)
VOL–VCC –1810
–1620 mV
Output High
Voltage(9)
VOH–VCC –1025
–880
Output Data Rise/Fall
Time, 20%–80%
t ,t
1.3
1380 nm
200
0.6
Symbol
2.0
ns
–14
–11
9
dBm
dB
Notes
1. Measured at the end of 5 meters of 62.5/125/0.275 graded index
fiber using calibrated power meter and a precision test ferrule.
Cladding modes are removed. Values valid for EOL.
Output SD Rise/Fall
Time, 20%–80%
2. The input data pattern is a 12.5 MHz square wave pattern.
ns
R F
40
3. Center wavelength is defined as the midpoint between the two
50% levels of the optical spectrum of the LED.
Notes
4. Spectral width (full width, half max.) is defined as the difference
between 50% levels of the optical spectrum of the LED.
2. For a bit error rate (BER) of less than 1x10E-12 over a receiver eye
opening of least 1.0 ns. Measured with a 27–1 PRBS.
5. 10% to 90% levels. Measured using a 12.5 MHz square wave pattern with an optoelectronic measurement system (detector and
oscilloscope) with 3 dB bandwidth ranging from less than 0.1 MHz
to more than 750 MHz.
3. For a BER of less than 1x10E-12. Measured in the center of the eye
opening with a 27–1 PRBS.
1. Pattern: Manchester coding / NRZI (no scrambling)
4. Test method and considerations as in FH-PC Appendix A.
5. Measured with the K28.5 pattern from Chapter II of the FC-PH at
266 MBd.
6. Extinction ratio is defined as PL/PH x 100%. Measurement system
as in Note 5.
6. Measured with the K28.7 pattern from Chapter II of the FC-PH
which equals a 133 MHz square wave.
7. Test method and consideration as in FC-PH Appendix A.
8. Measured with the K28.5 pattern from Chapter II of the FC-PH at
266 MBd.
7. An increase in optical power through the specified level will cause
the Signal Detect output to switch from a Low state to a High state.
9. Measured with the K28.7 pattern from Chapter II of the FC-PH
which equals a 133 MHz square wave.
8. A decrease in optical power through the specified level will cause
the Signal Detect output to switch from a High state to a Low state.
9. PECL compatible. Load is 50 Ω into VCC–2 V. Measured under DC
conditions. For dynamic measurements a tolerance of 50 mV should
be added for VCC=5 V.
Fiber Optics
V23809-F7–T10, MM 1300 nm LED Fibre Channel 1x9 Transceiver (ST)
3
Pin Description
Pin Name
Level
Pin #
Description
Rx Ground
Power Supply
1
Negative power supply, normally ground
RxD
Rx Output Data
PECL Output
2
Receiver output data
RxDn
Rx Output Data
PECL Output
3
Inverted receiver output data
Rx SD
RX Signal Detect
PECL Output
active high
4
A high level on this output shows that an optical signal
is applied to the optical input
RxVCC
Rx +3.3 to 5 V
Power Supply
5
Positive power supply, +3.3 to 5 V
TxVCC
Tx +3.3 to 5 V
Power Supply
6
Positive power supply, +3.3 to 5 V
TxDn
Tx Input Data
PECL Input
7
Inverted transmitter input data
TxD
Tx Input Data
PECL Input
8
Transmitter input data
TxVEE
Tx Ground
Power Supply
9
Negative power supply, normally ground
Case
Support
Not Connected
S1/S2
Support stud, not connected
RxVEE
APPLICATION NOTE
Multimode 1300 nm Fibre Channel 1x9 Transceiver
VCC Rx
VCC-Tx
GND
GND
9
VCC Tx
1
GND
GND
R7
C2
R1
C1
VCC-Rx
R5
VCC
R3
VCC
L1
RD
RDn
SD
L2
L1/2
= 15000 nH (L2 is optional)
C1/3
= 4700 nF (optional)
C2/4
= 4700 nF
R1/3/5/7
= 82Ω (5V), 100Ω (4V), 127Ω (3.3V)
R2/4/6/8
= 130Ω (5V), 100Ω (4V), 83Ω (3.3V)
R9
= 200Ω
R8
R6
GND
R9
GND
VCC-Tx
R4
C4
R2
C3
TxD
TxDn
VCC-Rx
Transceiver
GNDGND
GND GNDGND
DC coupling between ECL gates.
The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module
VCC–Rx/VCC–Tx.
A GND plane under the module is recommended for good EMI
and sensitivity performance.
Fiber Optics
V23809-F7–T10, MM 1300 nm LED Fibre Channel 1x9 Transceiver (ST)
4
APPLICATION NOTE FOR MULTIMODE 1300 NM LED TRANSCEIVER
Solutions for connecting a Infineon 3.3 V Fiber Optic Transceiver to a 5.0 V Framer-/Phy-Device.
Figure 1. Common GND
Figure 1a. Circuitry for SD (Differential) and
Common GND
VCC 5.0 V
VCC 3.3 V
VCC
39K
127
VCC
VCC 5.0 V
26K
VCC
100 nF
Framer/Phy
Clock
Data
Recovery
Out
Tx
In
83
500
100 nF
500
Rx
Out
127
Data
In
180
VCC
68
VCC 3.3 V
SD Infineon
Fiber
Optic 3.3 V
Transceiver
83
Framer/Phy SD
Clock
Recovery
5V
SD
Figure 1b. Circuitry for SD (Single Ended)
and Common GND
VCC 5.0 V
VCC 3.3 V
SD
Out
VCC
VCC
18K
SD
In
Infineon
Fiber
Optic
Transceiver
1.8 V
Inputs and outputs are differential and should be
doubled. Signal Detect (SD) is single ended (if used).
SD
In
1
SD Infineon
Out Fiber
Optic 3.3 V
Transceiver
510
Framer/Phy
Clock
Recovery
5V
1 Zener-Diode 1.8 V
Figure 2. Common VCC
Framer/Phy
Clock
Data
Recovery
Out
Infineon
Fiber
Optic
Transceiver
GND 3.3 V Tx
In
130
Inputs and outputs are differential
and should be doubled. Signal
Detect (SD) is single ended.
VCC
Rx
Out
83
Data
In
82
VCC
127
VCC
SD GND 5.0 V
In
200
SD
Out
GND 5.0 V
GND 3.3 V
GND 3.3 V
Infineon Technologies AG • Fiber Optics • Wernerwerkdamm 16 • Berlin D-13623, Germany
Infineon Technologies, Corp. • Optoelectronics Division • 19000 Homestead Road • Cupertino, CA 95014 USA
Siemens K.K. • Fiber Optics • Takanawa Park Tower • 20-14, Higashi-Gotanda, 3-chome, Shinagawa-ku • Tokyo 141, Japan
www.infineon.com/fiberoptics