INFINEON V23809-C8-T10

*
11 dB
Multimode 1300 nm LED Fast Ethernet/FDDI/ATM
170 MBd 1x9 Transceiver with ST Connector
V23809-C8-T10
Dimensions in (mm) inches
(1) .039
(1.4)
A
1
(0.6)
.024
(2.8)
max.
.11
max.
bottom
view
(25.4) max.
1 max.
(12.7)
.5
(2.54)
.1
(20.32)
8
9
(0.46) .02 x 9
∅(0.3) M A M
(3.8) .15 max.
2x ∅(1.4)
∅.055
∅(0.1) M A M
(9.8) max.
.39 max.
(5.27) .207
(14.4) .567
(18.47) .727
(20.32) .8
(41.2) 1.622
(3–0.2)
.118–.008
APPLICATIONS
• ATM switches/bridges/routers
• Fast Ethernet, FDDI
• High speed computer links
• Local area networks
• Switching systems
Absolute Maximum Ratings
Exceeding any one of these values may destroy the device
immediately.
FEATURES
• Compliant with Fast Ethernet, FDDI, Fibre Channel,
ATM/SONET/SDH standards
• Meets mezzanine standard height of 9.8 mm
• Compact integrated transceiver unit with duplex SC
receptacle
• Single power supply with 3.0 V to 5.5 V range
• Extremely low power consumption < 0.7 W at 3.3 V
• PECL differential inputs and outputs
• System optimized for 62.5/50 µm graded index fiber
• Industry standard multisource footprint
• Testboard available
• UL-94 V-0 certified
• ESD Class 2 per MIL-STD 883 Method 3015
• Compliant with FCC (Class B) and EN 55022
• For distances of up to 2 km on multimode fiber
Fiber Optics
Supply Voltage (VCC–VEE)....................................... –0.5 V to 7 V
Data Input Levels (PECL) (VIN)..................................... VEE–VCC
Differential Data Input Voltage ............................................... 3 V
Operating Ambient Temperature (TAMB) ... ... ... ... 0°C to 85°C
Storage Ambient Temperature ............................ –40°C to 85°C
Soldering Conditions, Temp/Time (TSOLD/tSOLD)
(MIL-STD 883C, Method 2003) .............................. 270°C/10 s
ESD Resistance (all pins to V EE, human body) .................. 1.5 kV
Output Current (IO) ........................................................... 50 mA
*Available also as 8 dB V23809-C8-T11 on request
ST is a registered trademark of AT&T
JULY 1999
TECHNICAL DATA
The electro-optical characteristics described in the following
tables are valid only for use under the recommended operating
conditions.
DESCRIPTION
This data sheet describes the Infineon Fast Ethernet/FDDI/ATM
transceiver—part of Infineon Multistandard Transceiver Family.
It is fully compliant with the Asynchronous Transfer Mode
(ATM) OC-3 standard, the Fiber Distributed Data Interface
(FDDI) Low Cost Fiber Physical Layer Medium Dependent (LCFPMD) draft standard(1), and the FDDI PMD standard(2).
Recommended Operating Conditions
ATM was developed because of the need for multimedia applications, including real time transmission. The data rate is scalable and the ATM protocol is the basis of the broadband public
networks being standardized in the International Telegraph and
Telephone Consultative Committee (CCITT). ATM can also be
used in local private applications.
Parameter
Symbol
Min.
Ambient Temperature
TAMB
0
Power Supply Voltage
VCC–VEE
3
Supply Current 3.3 V
ICC
Typ. Max.
70
Supply Current 5 V(1)
Units
°C
5.5
V
230
mA
260
Transmitter
FDDI is a Dual Token Ring standard developed in the U.S. by the
Accredited National Standards Committee (ANSC) X3T9, within
the Technical Committee X3T9.5. It is applied to the local area
networks of stations, transferring data at 100 Mbits/s with a
125 MBaud transmission rate. LCF FDDI is specially developed
for short distance applications of up to 500 m (fiber-to-the-desk)
as compared to 2 km for backbone applications.
Data Input
High Voltage
VIH–VCC
–1165
–880
Data Input
Low Voltage
VIL–VCC
–1810
–1475
Threshold Voltage
VBB–VCC –1380
–1260
Input Data Rise/Fall,
20%–80%
tR, tF
1.3
Fast Ethernet was developed because of the higher bandwidth
requirement in local area networking. It is based on the proven
effectiveness of millions of installed Ethernet systems.
Data High Time(2)
ton
1000
Output Current
lO
25
mA
Input Duty Cycle
Distortion
tDCD
1.0
ns
Input Data
Dependent Jitter
tDDj
Input Random Jitter
tRJ
Input Center
Wavelength
lC
Electrical Output
Load(3)
RL
The inputs/outputs are PECL compatible and the unit operates
from a 3.0 V to 5.5 V power supply. As an option, the data output stages can be switched to static levels during absence of
light, as indicated by the Signal Detect function. It can be
directly interfaced with available chipsets.
Notes
FCC Class B
EN 55022 Class B
CISPR 22
Noise frequency
range:30 MHz to
1 GHz
Immunity:
Electrostatic
Discharge
EN 61000-4-2
IEC 1000-4-2
Discharges of
± 15kV with an air
discharge probe on
the receptacle cause
no damage.
Immunity:
Radio Frequency
Electromagnetic
Field
EN 61000-4-3
IEC 1000-4-3
With a field strength
of 10 V/m rms, noise
frequency ranges
from 10 MHz to
1 GHz
Eye Safety
IEC 825-1
Class 1
1380
50
nm
Ω
2. To maintain good LED reliability, the device should not be held in the
ON state for more than the specified time. Normal operation should
be done with 50% duty cycle.
Regulatory Compliance
Electromagnetic
Interference (EMI)
1260
1. For VCC–VEE (min., max.). 50% duty cycle. The supply current
(ICC2+ICC3) does not include the load drive current (Icc1). Add max.
45 mA for the three outputs. Load is 50 Ω into VCC –2V.
2. FDDI Token Ring, Physical Layer Medium Dependent (PMD) ANSI
X3.166-1990 American National Standard. ISO/IEC 9314-3: 1990.
Comments
0.76
Notes
1. FDDI Token Ring, Low Cost Fiber Physical Layer Medium Dependent (LCF-PMD) ANSI X3T9.5 / 92 LCF-PMD / Proposed Rev. 1.3,
September 1, 1992. American National Standard.
Standard
ns
Receiver
The Infineon multimode transceiver is a single unit comprised
of a transmitter, a receiver, and an ST receptacle. This design
frees the customer from many alignment and PC board layout
concerns. The modules are designed for low cost applications.
Feature
0.4
mV
3. To achieve proper PECL output levels the 50 Ω termination should be
done to VCC –2 V. For correct termination see the application notes.
Fiber Optics
V23809-C8–T10, MM 1300 nm LED Fast Ethernet/FDDI/ATM Transceiver (ST)
2
Transmitter Electro-Optical Characteristics
Transmitter
Symbol Min.
Data Rate
DR
Launched Power
(Average) into 62.5 µm
Fiber for –C8–C10(1, 2)
PO
Launched Power
(Average) into 62.5 µm
Fiber for –C8–C11(1, 2)
Center Wavelength(2, 3) λC
Spectral Width
(FWHM)(2, 4)
Dl
Output Rise/Fall Time,
10%–90%(2, 5)
tR, tF
Temperature
Coefficient of Optical
Output Power
Typ.
–20
–16
–22
–17
Receiver Electro-Optical Characteristics
Max.
Units
Receiver
Symbol
Min.
5(1)
170
MBaud
Data Rate
DR
–14
dBm
Sensitivity
Average Power)(2)
PIN
Sensitivity (Average
Power) Center(3)
1360
nm
170
0.6
Max.
170
MBaud
–33
–31
dBm
–14
ns
–11
Duty Cycle
Distortion(4, 5)
tDCD
1
Deterministic
Jitter(5, 6)
tDJ
1
Random Jitter(5, 7)
tRJ
Signal Detect
Assert Level(8)
PSDA
–42.5
–30
–31.5
2.5
ns
TCp
0.03
dB/°C
Extinction Ratio
(Dynamic)(2, 6)
ER
10
%
Signal Detect
Deassert Level(9)
PSDD
–45
Optical Power Low(7)
PTD
–45
dBm
Signal Detect
Hysteresis
1.0
Overshoot
OS
10
%
PSDA–
PSDD
tDCD
0.6
ns
Output Low
Voltage(10)
VOL–VCC –1810
–1620
Duty Cycle
Distortion(8, 9)
tDDJ
0.3
Output High
Voltage(10)
VOH–VCC –1025
–880
Data Dependent
Jitter(8, 10)
tRJ
0.6
Output Data
Rise/Fall Time,
20%–80%
tR, tF
1.3
Random Jitter(8, 11)
Notes
Units
–35.5
Saturation (Average PSAT
Power)(3)
1270
Typ.
Output SD
Rise/Fall Time,
20%–80%
dBm
dB
mV
ns
40
1. Measured at the end of 5 meters of 62.5/125/0.275 graded index
fiber using calibrated power meter and a precision test ferrule.
Cladding modes are removed. Values valid for EOL and worst-case
temperature.
Notes
2. The input data pattern is a 12.5 MHz square wave pattern.
1. Pattern: Manchester coding / NRZI (no scrambling)
3. Center wavelength is defined as the midpoint between the two
50% levels of the optical spectrum of the LED.
2. For a bit error rate (BER) of less than 1x10E–12 over a receiver eye
opening of least 1.5 ns. Measured with a 223–1 PRBS at 155 MBd.
4. Spectral width (full width, half max) is defined as the difference
between 50% levels of the optical spectrum of the LED.
3. For a BER of less than 1x10E-12. Measured in the center of the eye
opening with a 223-1 PRBS at 155 MBd.
5. 10% to 90% levels. Measured using the 12.5 MHz square wave
pattern with an optoelectronic measurement system (detector
and oscilloscope) having 3 dB bandwidth ranging from less than
0.1 MHz to more than 750 MHz.
4. Measured at an average optical power level of –20 dBm with a 62.5
MHz square wave.
5. All jitter values are peak-to-peak. RX output jitter requirements are
not considered in the ATM standard draft. In general the same
requirements as for FDDI are met.
6. Extinction Ratio is defined as PL/PH x 100%. Measurement system
as in Note 5.
6. Measured at an average optical power level of –20 dBm.
7. Optical Power Low is the output power level when a steady state
low data pattern (FDDI Quiet Line state) is used to drive the transmitter. Value valid <1 ms after input low.
7. Measured at –33 dBm average power.
8. Test method as for FDDI-PMD. Jitter values are peak-to-peak.
8. An increase in optical power through the specified level will
cause the SIGNAL detect output to switch from a Low state to
a High state.
9. Duty Cycle Distortion is defined as 0.5 [(width of wider state) minus
(width of narrower state)]. It is measured with stream of Idle
Symbols (62.5 MHz square wave).
9. A decrease in optical power through the specified level will
cause the SIGNAL detect output to switch from a High state to
a Low state.
10.Measured with the same pattern as for FDDI-PMD.
10. PECL compatible. Load is 50 Ω into VCC –2 V. Measured under DC
conditions. For dynamic measurements a tolerance of 50 mV should
be added for VCC=5 V.
11. Measured with the Halt Line state (12.5 MHz square wave).
Fiber Optics
V23809-C8–T10, MM 1300 nm LED Fast Ethernet/FDDI/ATM Transceiver (ST)
3
Pin Description
Pin Name
Level/Logic
Pin#
Description
RxVEE
Rx Ground
Power Supply
1
Negative power supply, normally ground
RD
Rx Output Data
PECL Output
RDn
2
Receiver output data
3
Inverted receiver output data
RxSD
RX Signal Detect
PECL Output active high 4
High level on this output shows there is an optical signal.
RxVCC
Rx +3.3 V...5 V
Power Supply
5
Positive power supply, +3.3 V...5 V
TxVCC
Tx +3.3 V...5 V
TxDn
Tx Input Data
PECL Input
7
8
Transmitter input data
TxVEE
Tx Ground
Power Supply
9
Negative power supply, normally ground
Case
Support
Not Connected
S1/S2
Support stud, not connected
6
TxD
Inverted transmitter input data
APPLICATION NOTE
Multimode 1300 nm 1x9 Transceiver
VCC–RX
VCC–TX
C1/3=4700 nF (optional)
VCC–RX
C2/4=4700 nF
GND
R5
82R
GND
R3
82R
82R
R1
82R
L1/2=15000 nH (L2 is optional)
VCC
L1
1
9
VCC
R7
RD
RDN
SD
TXD
TXDN
C1
C2
GND
GND
L2
R1/3
82
100
127
R2/4
130
100
83
R5/7
82
100
127
R6/8
130
100
83
GNDGND
R9
VCC-RX
130R
R4
130R
3.3 V
200R
4V
130R
R2
5V
130R
VCC-TX
R in Ohm
VCC–TX
R8
C3
C4
GND
GND
R6
Transceiver
GND GNDGND
DC coupling between ECL gates.
R9=200 Ohm
A GND plane under the module is recommended for good EMI
and sensitivity performance.
The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module
VCC-Rx/VCC-Tx.
Fiber Optics
V23809-C8–T10, MM 1300 nm LED Fast Ethernet/FDDI/ATM Transceiver (ST)
4
APPLICATION NOTE FOR MULTIMODE 1300 NM LED TRANSCEIVER
Solutions for connecting a Infineon 3.3 V Fiber Optic Transceiver to a 5.0 V Framer-/Phy-Device.
Figur 1. Common GND
Figure 1a. Circuitry for SD (Differential) and
Common GND
VCC 5.0 V
VCC 3.3 V
VCC
39K
127
VCC
VCC 5.0 V
26K
VCC
100 nF
Framer/Phy
Clock
Data
Recovery
Out
Tx
In
83
500
100 nF
500
Rx
Out
127
Data
In
180
VCC
68
VCC 3.3 V
SD Infineon
Fiber
Optic 3.3 V
Transceiver
83
Framer/Phy SD
Clock
Recovery
5V
SD
Figure 1b. Circuitry for SD (Single Ended)
and Common GND
VCC 5.0 V
VCC 3.3 V
SD
Out
VCC
VCC
18K
SD
In
Infineon
Fiber
Optic
Transceiver
1.8 V
Inputs and outputs are differential and should be
doubled. Signal Detect (SD) is single ended (if used).
SD
In
1
SD Infineon
Out Fiber
Optic 3.3 V
Transceiver
510
Framer/Phy
Clock
Recovery
5V
1 Zener-Diode 1.8 V
Figure 2. Common VCC
Framer/Phy
Clock
Data
Recovery
Out
Infineon
Fiber
Optic
Transceiver
GND 3.3 V Tx
In
130
Inputs and outputs are differential
and should be doubled. Signal
Detect (SD) is single ended.
VCC
Rx
Out
83
Data
In
82
VCC
127
VCC
SD GND 5.0 V
In
200
SD
Out
GND 5.0 V
GND 3.3 V
GND 3.3 V
Infineon Technologies AG • Fiber Optics • Wernerwerkdamm 16 • Berlin D-13623, Germany
Infineon Technologies, Corp. • Fiber Optics • 19000 Homestead Road • Cupertino, CA 95014 USA
Siemens K.K. • Fiber Optics • Takanawa Park Tower • 20-14, Higashi-Gotanda, 3-chome, Shinagawa-ku • Tokyo 141, Japan
www.infineon.com/fiberoptics