CY7C65632, CY7C65634 HX2VL™ Very Low Power USB 2.0 Hub Controller HX2VL™ Very Low Power USB 2.0 Hub Controller Features Integrated port status indicator control 12 MHz +/– 500 ppm external crystal with drive level 600 µW (integrated PLL) clock input with optional 27/48 MHz oscillator clock input ❐ Internal power failure detection for ESD recovery ❐ ■ High performance, low-power USB 2.0 Hub, optimized for low cost designs with minimum Bill-of-material ■ USB 2.0 hub controller ❐ Compliant with USB 2.0 specification ❐ Up to four downstream ports support ❐ Downstream ports are backward compatible with FS, LS ❐ Single transaction translator (TT) for low cost ■ Very low power consumption ❐ Supports bus-powered and self-powered modes ❐ Auto switching between bus-powered and self-powered ❐ Single MCU with 2K ROM and 64 byte RAM ❐ Lowest power consumption ■ Highly integrated solution for reduced BOM cost ❐ Internal regulator – single power supply 5 V required ❐ Provision of connecting 3.3 V with external regulator ❐ Integrated upstream pull-up resistor ❐ Integrated pull-down resistors for all downstream ports ❐ Integrated upstream/downstream termination resistors ❐ ■ Downstream port management ❐ Support individual and ganged mode power management ❐ Overcurrent detection ❐ Two port status indicators per downstream port ❐ Slew rate control for EMI management ■ Maximum configurability ❐ VID and PID are configurable through external EEPROM ❐ Number of ports, removable/non-removable ports are configurable through EEPROM and I/O pin configuration ❐ I/O pins can configure gang/individual mode power switching, reference clock source and polarity of power switch enable pin ❐ Configuration options also available through mask ROM ■ Available in space saving 48-pin (7 × 7 mm) TQFP and 28-pin (5 × 5 mm) QFN packages ■ Supports 0 °C to 70 °C temperature range Block Diagram – CY7C6563X D+ 12/27/48 MHz OSC-in OR 12 MHz Crystal I2C / SPI MCU D- RAM USB 2.0 PHY Serial Interface Engine PLL ROM HS USB Control Logic USB Upstream Port 5V i/p (for internal regulator) NC (for external regulator) Transaction Translator 1.8V Regulator Hub Repeater 3.3V 3.3V i/p (with ext. reg. & 28 QFN) NC (with ext. reg. & 48 TQFP) 3.3V o/p (for int. reg.) Routing Logic USB Downstream Port 3 USB Downstream Port 4 USB 2.0 PHY USB 2.0 PHY USB 2.0 PHY Cypress Semiconductor Corporation Document Number: 001-67568 Rev. *H • D+ D- 198 Champion Court LED D+ D- • Port Control O V R # [4] LED Port Control O V R # [3] D+ D- O V R # [2] LED Port Control P W R # [2] O V R # [1] P W R # [1] D+ D- Port Control P W R # [4] USB Downstream Port 2 USB 2.0 PHY P W R # [3] USB Downstream Port 1 For two port version, USB Downstream ports 3 and 4 are to be No connect from the Chip I/O perspective. LED San Jose, CA 95134-1709 • 408-943-2600 Revised February 17, 2015 CY7C65632, CY7C65634 More Information Cypress provides a wealth of data at www.cypress.com to help you to select the right HX2VL device for your design, and to help you to quickly and effectively integrate the device into your design. For a comprehensive list of resources, see the knowledge base article http://www.cypress.com/?id=2411. ■ ■ ■ Overview: USB Portfolio, USB Roadmap USB 2.0 Hub Controller Selectors: HX2LP, HX2VL Application notes: Cypress offers a large number of USB application notes covering a broad range of topics, from basic to advanced level. Recommended application notes for getting started with HX2VL are: ❐ AN15454 - Bus-Powered USB Hub Design Using EZ-USB HX2LP™/HX2VL ❐ AN72332 - Guidelines on System Design using Cypress's USB 2.0 Hub (HX2VL) ❐ AN69235 - Migrating from HX2/HX2LP to HX2VL ■ Reference Designs: ❐ CY4608 HX2VL Very Low-Power USB 2.0 Compliant 4-Port Hub Development Kit ❐ CY4607 HX2VL Very Low-Power USB 2.0 Compliant 4-Port Hub Development Kit ■ Models: HX2VL (CY7C65632/34/42) - IBIS HX2VL Development Kit HX2VL Development Kit board is a tool to demonstrate the features of HX2VL devices (CY7C65632, CY7C65634). In the initial phase of the design, this board helps developers to understand the chip features and limitations before proceeding with a complete design. The Development kit includes support documents related to board hardware, PC application software, and EEPROM configuration data (.iic) files. Document Number: 001-67568 Rev. *H Page 2 of 28 CY7C65632, CY7C65634 Contents Introduction ....................................................................... 4 HX2VL Architecture .......................................................... 4 USB Serial Interface Engine ........................................ 4 HS USB Control Logic ................................................. 4 Hub Repeater .............................................................. 4 MCU ............................................................................ 4 Transaction Translator ................................................ 4 Port Control ................................................................. 4 Applications ...................................................................... 4 Functional Overview ........................................................ 5 System Initialization ..................................................... 5 Enumeration ................................................................ 5 Upstream Port ............................................................. 5 Downstream Ports ....................................................... 5 Power Switching .......................................................... 5 Overcurrent Detection ................................................. 5 Port Indicators ............................................................. 5 Power Regulator .......................................................... 6 External Regulation Scheme ....................................... 6 Internal Regulation Scheme ........................................ 6 Pin Configurations ........................................................... 7 Pin Definitions ................................................................ 11 Pin Definitions ................................................................ 13 EEPROM Configuration Options ................................... 15 Pin Configuration Options ............................................. 16 Power ON Reset ....................................................... 16 Gang/Individual Power Switching Mode .................... 16 Power Switch Enable Pin Polarity ............................. 16 Document Number: 001-67568 Rev. *H Port Number Configuration ........................................ 16 Non Removable Ports Configuration ......................... 16 Reference Clock Configuration ................................. 17 Absolute Maximum Ratings .......................................... 18 Operating Conditions ..................................................... 18 Electrical Characteristics ............................................... 18 DC Electrical Characteristics ..................................... 18 AC Electrical Characteristics ..................................... 20 Thermal Resistance ........................................................ 20 Ordering Information ...................................................... 21 Ordering Code Definitions ......................................... 21 Package Diagrams .......................................................... 22 Acronyms ........................................................................ 24 Document Conventions ................................................. 24 Units of Measure ....................................................... 24 Silicon Errata for the HX2VL, CY7C65632 Product Family .............................................................................. 25 Part Numbers Affected .............................................. 25 HX2VL Qualification Status ....................................... 25 HX2VL Errata Summary ............................................ 25 Document History Page ................................................. 26 Sales, Solutions, and Legal Information ...................... 28 Worldwide Sales and Design Support ....................... 28 Products .................................................................... 28 PSoC® Solutions ....................................................... 28 Cypress Developer Community ................................. 28 Technical Support ..................................................... 28 Page 3 of 28 CY7C65632, CY7C65634 Introduction MCU HX2VL™ is Cypress’s next generation family of high performance, very low power USB 2.0 hub controllers. HX2VL has integrated upstream and downstream transceivers; a USB Serial Interface Engine (SIE); USB Hub Control and Repeater logic; and Transaction Translator (TT) logic. Cypress has also integrated external components such as voltage regulator and pull-up/pull-down resistors, reducing the overall bill of materials required to implement a USB hub system. HX2VL has MCU with 2K ROM and 64 byte RAM. The MCU operates with a 12 MHz clock to decode USB commands from host and respond to the host. It can also handle GPIO settings to provide higher flexibility to the customers and control the read interface to the EEPROM which has extended configuration options. The MCU is programmable while manufacturing in the factory as per customer needs. The CY7C6563X is a part of the HX2VL portfolio. This device option is for ultra low power but high performance applications that require up to four downstream ports. All downstream ports share a single transaction translator. The CY7C6563X is available in 48-pin TQFP and 28-pin QFN package options. All device options are supported by Cypress’s world class reference design kits, which include board schematics, bill of materials, Gerber files, Orcad files, and thorough design documentation. HX2VL Architecture The Block Diagram – CY7C6563X on page 1 shows the HX2VL single TT hub architecture. USB Serial Interface Engine The Serial Interface Engine (SIE) allows HX2VL to communicate with the USB host. The SIE handles the following USB activities independently of the Hub Control Block. ■ Bit stuffing and unstuffing ■ Checksum generation and checking ■ TOKEN type identification ■ Address checking HS USB Control Logic ‘Hub Control’ block co-ordinates enumeration, suspend and resume. It generates status and control signals for host access to the hub. It also includes the frame timer that synchronizes the hub to the host. It has status/control registers which function as the interface to the firmware in the MCU. Hub Repeater The Hub Repeater manages the connectivity between upstream and downstream facing ports that are operating at the same speed. It supports full and high speed connectivity. According to the USB 2.0 specification, the HUB Repeater provides the following functions: ■ Sets up and tears down connectivity on packet boundaries ■ Ensures orderly entry into and out of ‘Suspend’ state, including proper handling of remote wakeups. Document Number: 001-67568 Rev. *H Transaction Translator The Transaction Translator translates data from one speed to another. A TT takes high speed split transactions and translates them to full or low speed transactions when the hub is operating at high speed (the upstream port is connected to a high speed host controller) and has full or low speed devices attached. The operating speed of a device attached on a downstream port determines whether the routing logic connects a port to the TT or to hub repeater. When the upstream host and downstream device are functioning at different speeds, the data is routed through the TT. In all other cases, the data is routed through the repeater. For example, If a full or low speed device is connected to the high speed host upstream through the hub, then the data transfer route includes TT. If a high speed device is connected to the high speed host upstream through the hub, the transfer route includes the repeater. When the hub is connected to a full speed host controller upstream, then high speed peripheral does not operate at its full capability. These devices only work at full speed. Full and low speed devices connected to this hub operate at their normal speed. Port Control The downstream ‘Port Control’ block handles the connect/disconnect and over current detection as well as the power enable and LED control. It also generates the control signals for the downstream transceivers. Applications Typical applications for the HX2VL device family are: ■ Docking stations ■ Standalone hubs ■ Monitor hubs ■ Multi-function printers ■ Digital televisions ■ Advanced port replicators ■ Keyboard hubs ■ Gaming consoles Page 4 of 28 CY7C65632, CY7C65634 Functional Overview The Cypress CY7C6563X USB 2.0 Hubs are low power hub solutions for USB which provide maximum transfer efficiency. The CY7C6563X USB 2.0 Hubs integrate 1.5 kohm upstream pull-up resistors for full speed operation and all downstream 15 kohm pull-down resistors and series termination resistors on all upstream and downstream D+ and D– pins. This results in optimization of system costs by providing built-in support for the USB 2.0 specification. System Initialization On power up, CY7C6563X has an option to enumerate from the default settings in the mask ROM or from reading an external EEPROM for configuration information. At the most basic level, this EEPROM has the Vendor ID (VID) and the Product ID (PID), for the customer’s application. For more specialized applications, other configuration options can be specified. See EEPROM Configuration Options on page 15 for more details. CY7C6563X verifies the checksum before loading the EEPROM contents as the descriptors. Enumeration CY7C6563X enables the pull-up resistor on D+ to indicate its presence to the upstream hub, after which a USB Bus Reset is expected. After a USB Bus Reset, CY7C6563X is in an unaddressed, unconfigured state (configuration value set to ’0’). During the enumeration process, the host sets the hub's address and configuration. After the hub is configured, the full hub functionality is available. Upstream Port The upstream port includes the transmitter and the receiver state machine. The transmitter and receiver operate in high speed and full speed depending on the current hub configuration. The transmitter state machine monitors the upstream facing port while the Hub Repeater has connectivity in the upstream direction. This machine prevents babble and disconnect events on the downstream facing ports of this hub from propagating and causing the hub to be disabled or disconnected by the hub to which it is attached. Downstream Ports The CY7C6563X supports a maximum of four downstream ports, each of which may be marked as usable or removable in the EEPROM configuration, see EEPROM Configuration Options on page 15. Additionallyit can also be configured by pin strapping, see Pin Configuration Options on page 16. Downstream D+ and D– pull-down resistors are incorporated in CY7C6563X for each port. Before the hubs are configured, the ports are driven SE0 (Single Ended Zero, where both D+ and D– are driven low) and are set to the unpowered state. When the hub is configured, the ports are not driven and the host may power the ports by sending a SetPortPower command for each port. After a port is powered, any connect or disconnect event is detected by the hub. Any change in the port state is reported by the hubs back to the host through the Status Change Endpoint (endpoint 1). Document Number: 001-67568 Rev. *H On receipt of SetPortReset request for a port with a device connected, the hub does as follows: ■ Performs a USB Reset on the corresponding port ■ Puts the port in an enabled state ■ Enables babble detection after the port is enabled. Babble consists of a non idle condition on the port after EOF2. If babble is detected on an enabled port, that port is disabled. A ClearPortEnable request from the host also disables the specified port. Downstream ports can be individually suspended by the host with the SetPortSuspend request. If the hub is not suspended, a remote wakeup event on that port is reflected to the host through a port change indication in the Hub Status Change Endpoint. If the hub is suspended, a remote wakeup event on this port is forwarded to the host. The host may resume the port by sending a ClearPortSuspend command. Power Switching The CY7C6563X includes interface signals for external port power switches. Both ganged and individual (per-port) configurations are supported by pin strapping, see Pin Configuration Options on page 16. After enumerating, the host may power each port by sending a SetPortPower request for that port. Power switching and overcurrent detection are managed using respective control signals (PWR#[n] and OVR#[n]) which are connected to an external power switch device. Both High/Low enabled power switches are supported and the polarity is configured through GPIO setting, see Pin Configuration Options on page 16. Overcurrent Detection The OVR#[n] pins of the CY7C6563X series are connected to the respective external power switch's port overcurrent indication (output) signals. After detecting an overcurrent condition, hub reports overcurrent condition to the host and disables the PWR#[n] output to the external power device. OVR#[n] has a setup time of 20 ns. It takes 3 to 4 ms from overcurrent detection to de-assertion of PWR#[n] Port Indicators The USB 2.0 port indicators are also supported directly by CY7C6563X. According to the specification, each downstream port of the hub optionally supports a status indicator. The presence of indicators for downstream facing ports is specified by bit 7 of the wHub Characteristics field of the hub class descriptor. The default CY7C6563X descriptor specifies that the port indicators are supported. The CY7C6563X port indicators has two modes of operation: automatic and manual. On power up the CY7C6563X defaults to automatic mode, where the color of the Port Indicator (green, amber, off) indicates the functional status of the CY7C6563X port. The LEDs are turned off when the device is suspended. Page 5 of 28 CY7C65632, CY7C65634 Figure 2. External Regulation Scheme Figure 1. Port Status Indicator LED 5V to 3.3V Regulator PORT STATUS INDICATOR 5V to 3.3V Regulator LED VCC VREG Power Regulator CY7C6563X requires 3.3 V source power for normal operation of internal core logic and USB physical layer (PHY). The integrated low-drop power regulator converts 5 V power input from USB cable (Vbus) to 3.3 V source power. The 3.3 V power output is guaranteed by an internal voltage reference circuit when the input voltage is within the 4.75 V to 5.25 V range. The regulator’s maximum current loading is 150 mA, which provides tolerance margin over CY7C6563X’s normal power consumption of below 100 mA. The on chip regulator has a quiescent current of 28 µA. External Regulation Scheme CY7C6563X supports both external regulation and internal regulation schemes. When an external regulation is chosen, then for the 48 Pin package, VCC and VREG are to be left open with no connection. The external regulator output 3.3 V has to be connected to VCC_A and VCC_D pins. This connection has to be done externally, on board. For the 28-pin package, the 3.3 V output from the external regulator has to be connected to VREG, VCC_A and VCC_D. The VCC pin has to be left open with no connection. From the external input 3.3 V, 1.8 V is internally generated for the chip’s internal usage. NC NC NC VREG CY7C65632 48 Pin CY7C65632 28 Pin VCC_D VCC_A VCC VCC_A VCC_D External Regulation Scheme Internal Regulation Scheme When the built-in internal regulator is chosen, then the VCC pin has to be connected to a 5 V, in both 48-pin and 28-pin packages. Internally, the built-in regulator generates a 3.3 V and 1.8 V for the chip’s internal usage. Also a 3.3 V output is available at VREG pin, that has to be connected externally to VCC_A and VCC_D. Figure 3. Internal Regulation Scheme 5V 3.3V VCC VREG CY7C65632 48 Pin VCC_A 3.3V 5V VREG VCC CY7C65632 28 Pin VCC_D VCC_A VCC_D Internal Regulation Scheme Document Number: 001-67568 Rev. *H Page 6 of 28 CY7C65632, CY7C65634 Pin Configurations Figure 4. 48-pin TQFP (7 × 7 × 1.4 mm) pinout VREG VCC AMBER[1] / SPI_CS GREEN[1] / SPI_SK / FIXED_PORT1 SEL27 PWR#[1] / I2C_SDA OVR#[1] PWR#[2] OVR#[2] GANG VCC_D SELFPWR 48 47 46 45 44 43 42 41 40 39 38 37 VCC_A 1 36 AMBER[2] / SPI_MOSI / PWR_PIN_POL GND 2 35 GREEN[2] / SPI_MISO / FIXED_PORT2 D- 3 34 VCC_D D+ 4 33 AMBER[3] / SET_PORT_NUM2 DD-[1] 5 32 GREEN[3] / FIXED_PORT3 DD+[1] 6 31 PWR#[3] VCC_A 7 30 OVR#[3] GND 8 29 PWR#[4] DD-[2] 9 28 OVR#[4] DD+[2] 10 27 TEST / SCL RREF 11 26 RESET# VCC_A 12 25 SEL48 CY7C65632 48-pin TQFP 13 14 15 16 17 18 19 20 21 22 23 24 GND XIN XOUT VCC_A DD-[3] DD+[3] VCC_A GND DD-[4] DD+[4] GREEN[4] / FIXED_PORT4 AMBER[4] / SET_PORT_NUM1 Document Number: 001-67568 Rev. *H Page 7 of 28 CY7C65632, CY7C65634 Pin Configurations (continued) Figure 5. 48-pin TQFP (7 × 7 × 1.4 mm) pinout VREG VCC AMBER[1] / SPI_CS GREEN[1] / SPI_SK / FIXED_PORT1 SEL27 PWR#[1] / I2C_SDA OVR#[1] PWR#[2] OVR#[2] GANG VCC_D SELFPWR 48 47 46 45 44 43 42 41 40 39 38 37 Two Port VCC_A 1 36 AMBER[2] / SPI_MOSI / PWR_PIN_POL GND 2 35 GREEN[2] / SPI_MISO/ FIXED_PORT2 D- 3 34 VCC_D D+ 4 33 NC DD-[1] 5 32 NC DD+[1] 6 31 NC VCC_A 7 30 NC GND 8 29 NC DD-[2] 9 28 NC DD+[2] 10 27 TEST / SCL RREF 11 26 RESET# VCC_A 12 25 SEL48 CY7C65634 48-pin TQFP 13 14 15 16 17 18 19 20 21 22 23 24 GND XIN XOUT VCC_A NC NC NC GND NC NC NC NC Document Number: 001-67568 Rev. *H Page 8 of 28 CY7C65632, CY7C65634 Pin Configurations (continued) Figure 6. 28-pin QFN (5 × 5 × 0.8 mm) pinout VREG VCC PWR#/ I2C_SDA OVR # [1] OVR # [2] GANG SELFPWR 28 27 26 25 24 23 22 1 21 VCC_ D D+ 2 20 OVR # [3] DD - [1] 3 19 OVR # [4] DD + [1] 4 18 TEST/ I2C_SCL VCC_ A 5 17 RESET# DD - [2] 6 16 DD + [4] DD + [2] 7 15 DD - [4] CY7C65632 28-pin QFN 8 9 10 11 12 13 14 RREF VCC_ A XIN XOUT DD - [3] DD + [3] VCC_ A Document Number: 001-67568 Rev. *H - D- Page 9 of 28 CY7C65632, CY7C65634 Pin Configurations (continued) Figure 7. 28-pin QFN (5 × 5 × 0.8 mm) pinout VREG VCC PWR#/ I2C_SDA OVR # [1] OVR # [2] GANG SELFPWR 28 27 26 25 24 23 22 Two Port 1 21 D+ 2 20 NC DD - [1] 3 19 NC DD + [1] 4 18 TEST/ I2C_SCL VCC_ A 5 17 RESET# DD - [2] 6 16 NC DD + [2] 7 15 NC CY7C65634 28-pin QFN 8 9 10 11 12 13 14 RREF VCC_ A XIN XOUT NC NC VCC_ A Document Number: 001-67568 Rev. *H - D- VCC_ D Page 10 of 28 CY7C65632, CY7C65634 Pin Definitions 48-pin TQFP Package Name Power and Clock VCC_A VCC_A VCC_A VCC_A VCC_A VCC_D VCC_D VCC Pin No. Type [1] 1 7 12 16 19 34 38 47 P P P P P P P P VCC_A. 3.3 V analog power to the chip. VCC_A. 3.3 V analog power to the chip. VCC_A. 3.3 V analog power to the chip. VCC_A. 3.3 V analog power to the chip. VCC_A. 3.3 V analog power to the chip. NC in CY7C65634. VCC_D. 3.3 V digital power to the chip. VCC_D. 3.3 V digital power to the chip. VCC. 5 V input to the internal regulator; NC if using external regulator VREG GND GND GND GND XIN XOUT 48 2 8 13 20 14 15 P P P P P I O SEL48/SEL27 25 / 44 I RESET# 26 I SELFPWR 37 I GANG 39 I/O RREF System Interface Test I2C_SCL 11 I/O VREG. 5–3.3 V regulator o/p during internal regulation; NC if using external regulator. GND. Connect to Ground with as short a path as possible. GND. Connect to Ground with as short a path as possible. GND. Connect to Ground with as short a path as possible. GND. Connect to Ground with as short a path as possible. 12 MHz crystal clock input, or 12/27/48 MHz clock input. 12 MHz Crystal OUT Clock source selection inputs. 00: Reserved 01: 48 MHz OSC-in 10: 27 MHz OSC-in 11: 12 MHz Crystal or OSC-in Active LOW Reset. External reset input, default pull high 10 k; When RESET = low, whole chip is reset to the initial state. Self Power. Input for selecting self/bus power. 0 is bus powered, 1 is self powered. GANG. Default is input mode after power-on-reset. Gang Mode: Input:1 -> Output is 0 for Normal Operation and 1 for Suspend Individual Mode: Input:0 -> Output is 1 for Normal Operation and 0 for Suspend Refer to Gang/Individual Power Switching Modes in Pin Configuration Options Section for details 649 ohm resistor must be connected between RREF and Ground. 27 I(RDN) I/O(RDN) 3 4 I/O/Z I/O/Z Upstream D– Signal. Upstream D+ Signal. 5 I/O/Z Downstream D– Signal. Downstream D- signal of port 1. 6 I/O/Z Downstream D+ Signal. Downstream D+ signal of port 1. Upstream Port D– D+ Downstream Port 1 DD–[1] DD+[1] Description Test: 0: Normal Operation & 1: Chip will be put in test mode. I2C_SCL: Can be used as I2C clock pin to access I2C EEPROM. Notes 1. Pin Types: I = Input, O = Output, P = Power/Ground., Z = High Impedance, RDN = Pad internal Pull Down Resistor, RUP = Pad internal Pull Up Resistor. 2. The alternate function of these pins as LED indicator is not available if the pins are strapped to logic high, unless a separate circuit is designed to support logic high disconnect after 60 ms of power-on reset (POR), when these pins are reconfigured as outputs. Document Number: 001-67568 Rev. *H Page 11 of 28 CY7C65632, CY7C65634 Pin Definitions (continued) 48-pin TQFP Package Pin No. Type [1] SPI_CS 46 O(RDN) O(RDN) GREEN[1, 2] SPI_SK FIXED_PORT1 45 O(RDN) O(RDN) I(RDN) OVR#[1] 42 I(RUP) 43 O/Z I/O Active LOW Overcurrent Condition Detection Input. Overcurrent condition detection input for Port 1. Power Switch Driver Output. Default is Active LOW. I2C_SDA. Can be used as I2C Data pin, connected with I2C EEPROM. 9 10 I/O/Z I/O/Z Downstream D– Signal. Downstream D– signal of port 2. Downstream D+ Signal. Downstream D+ signal of port 2. 36 O(RDN) O(RDN) I(RDN) LED. Driver output for Amber LED. Port Indicator Support. Default is Active HIGH. SPI_MOSI. Can be used as Data Out to access external SPI EEPROM. PWR_PIN_POL. Used for power switch enable pin polarity setting. Refer Configuration Section. GREEN[2][2] SPI_MISO FIXED_PORT2 35 O(RDN) I(RDN) I(RDN) LED. Driver output for Green LED. Port Indicator Support. Default is Active HIGH. SPI_MISO. Can be used as Data In to access external SPI EEPROM. FIXED_PORT2. At POR used to set Port2 as non removable port. Refer Configuration Section. OVR#[2] 40 I(RUP) 41 O/Z 17 18 I/O/Z I/O/Z AMBER[3][2] SET_PORT_NUM2 33 O(RDN) I(RDN) GREEN[3][2] FIXED_PORT3 32 O(RDN) I(RDN) OVR#[3] 30 I(RUP) PWR#[3] 31 O/Z 21 I/O/Z Downstream D– Signal. NC in CY7C65634. 22 I/O/Z Downstream D+ Signal. NC in CY7C65634. Name AMBER[1][1, 2] PWR#[1] I2C_SDA Downstream Port 2 DD–[2] DD+[2] AMBER[2][2] SPI_MOSI PWR_PIN_POL PWR#[2] Downstream Port 3 DD–[3] DD+[3] Downstream Port 4 DD–[4] DD+[4] Description LED. Driver output for Amber LED. Port Indicator Support. Default is Active HIGH. SPI_CS. Can be used as chip select to access external SPI EEPROM. LED. Driver output for Green LED. Port Indicator Support. Default is Active HIGH. SPI_SK. Can be used as SPI Clock to access external SPI EEPROM. FIXED_PORT1. At POR used to set Port1 as non removable port. Refer pin configuration Section. Active LOW Overcurrent Condition Detection Input. Overcurrent condition detection input for Port 2. Power Switch Driver Output. Default is Active LOW. Downstream D– Signal. NC in CY7C65634. Downstream D+ Signal. NC in CY7C65634. LED. Driver output for Amber LED. Port Indicator Support. Default is Active HIGH. SET_PORT_NUM2. Used to set port numbering along with SET_PORT_NUM1. Refer pin configuration section. NC in CY7C65634. LED. Driver output for Green LED. Port Indicator Support. Default is Active HIGH. FIXED_PORT3. At POR used to set Port3 as non removable port. Refer pin configuration section. NC in CY7C65634. Active LOW Overcurrent Condition Detection Input. Overcurrent condition detection input for Port 3. NC in CY7C65634. Power Switch Driver Output. Default is Active LOW. NC in CY7C65634. Notes 1. Pin Types: I = Input, O = Output, P = Power/Ground., Z = High Impedance, RDN = Pad internal Pull Down Resistor, RUP = Pad internal Pull Up Resistor. 2. The alternate function of these pins as LED indicator is not available if the pins are strapped to logic high, unless a separate circuit is designed to support logic high disconnect after 60 ms of power-on reset (POR), when these pins are reconfigured as outputs. Document Number: 001-67568 Rev. *H Page 12 of 28 CY7C65632, CY7C65634 Pin Definitions (continued) 48-pin TQFP Package Type [1] Description 24 O(RDN) I(RDN) LED. Driver output for Amber LED. Port Indicator Support. Default is Active HIGH. SET_PORT_NUM1. Used to set port numbering along with SET_PORT_NUM2. Refer configuration Section. NC in CY7C65634. GREEN[4][2] FIXED_PORT4 23 O(RDN) I(RDN) OVR#[4] 28 I(RUP) PWR#[4] 29 O/Z Name AMBER[4][2] SET_PORT_NUM1 Pin No. LED. Driver output for Green LED. Port Indicator Support. Default is Active HIGH. FIXED_PORT4. At POR used to set Port4 as non removable port. Refer configuration Section. NC in CY7C65634. Active LOW Overcurrent Condition Detection Input. Overcurrent condition detection input for Port 4. NC in CY7C65634. Power Switch Driver Output. Default is Active LOW. NC in CY7C65634. Notes 1. Pin Types: I = Input, O = Output, P = Power/Ground., Z = High Impedance, RDN = Pad internal Pull Down Resistor, RUP = Pad internal Pull Up Resistor. 2. The alternate function of these pins as LED indicator is not available if the pins are strapped to logic high, unless a separate circuit is designed to support logic high disconnect after 60 ms of power-on reset (POR), when these pins are reconfigured as outputs. Pin Definitions 28-pin QFN Package Name Power and Clock VCC_A VCC_A VCC_A VCC_D VCC Pin No. Type [2] Description 5 9 14 21 27 P P P P P VREG 28 P XIN XOUT 10 11 I O RESET# 17 I SELFPWR 22 I VCC_A. 3.3 V analog power to the chip. VCC_A. 3.3 V analog power to the chip. VCC_A. 3.3 V analog power to the chip. VCC_D. 3.3 V digital power to the chip. VCC. 5 V input to the internal regulator; NC if using external regulator VCC. 5–3.3 V regulator o/p during internal regulation; 3.3 V I/P if using external regulator. 12 MHz crystal clock input, or 12 MHz clock input 12 MHz Crystal OUT Active LOW Reset. External reset input, default pull high 10 k; When RESET = low, whole chip is reset to the initial state Self Power. Input for selecting self/bus power. 0 is bus powered, 1 is self powered. GANG[5] 23 I/O RREF System Interface 8 I/O GANG. Default is input mode after power-on-reset. Gang Mode: Input:1 -> Output is 0 for Normal Operation and 1 for Suspend Individual Mode: Input:0 -> Output is 1 for Normal Operation and 0 for Suspend Refer to Gang/Individual Power Switching Modes in Pin Configuration Options Section for details 649 ohm resistor must be connected between RREF and Ground Notes 3. Pin Types: I = Input, O = Output, P = Power/Ground., Z = High Impedance, RDN = Pad internal Pull Down Resistor, RUP = Pad internal Pull Up Resistor. 4. PWR#/I2C_SDA can be used as either PWR# or I2C_SDA but not as both. If EEPROM is connected then the pin will act as I2C_SDA, it will not switch to PWR# mode (as it does in 48-pin TQFP package). 5. In Gang mode, only OVR#1 (pin 25) is enabled. Document Number: 001-67568 Rev. *H Page 13 of 28 CY7C65632, CY7C65634 Pin Definitions (continued) 28-pin QFN Package Pin No. Type [2] 18 I(RDN) I/O(RDN) 26 I/O 1 2 I/O/Z I/O/Z Upstream D– Signal. Upstream D+ Signal. 3 4 I/O/Z I/O/Z Downstream D– Signal. Downstream D+ Signal. 25 I(RUP) Active LOW Overcurrent Condition Detection Input. Overcurrent condition detection input for Port 1. 6 7 I/O/Z I/O/Z Downstream D– Signal. Downstream D+ Signal. 24 I(RUP) Active LOW Overcurrent Condition Detection Input. Overcurrent condition detection input for Port 2. 12 13 I/O/Z I/O/Z 20 I(RUP) Downstream D– Signal. NC in CY7C65634. Downstream D+ Signal. NC in CY7C65634. Overcurrent Condition Detection Input. Default is Active LOW. NC in CY7C65634. 15 16 I/O/Z I/O/Z Downstream D– Signal. NC in CY7C65634. Downstream D+ Signal. NC in CY7C65634. OVR#[4] 19 I(RUP) GND PAD P Name Test I2C_SCL PWR# [3] I2C_SDA Upstream Port D– D+ Downstream Port 1 DD–[1] DD+[1] OVR#[1] Downstream Port 2 DD–[2] DD+[2] OVR#[2] Downstream Port 3 DD–[3] DD+[3] OVR#[3] Downstream Port 4 DD–[4] DD+[4] Description Test: 0: Normal Operation & 1: Chip will be put in test mode I2C_SCL: I2C Clock pin. Power Switch Driver Output. Default is Active LOW. I2C_SDA: I2C Data pin. Overcurrent Condition Detection Input. Default is Active LOW. NC in CY7C65634. Ground pin for the chip. It is the solderable exposed pad beneath the chip. Refer Figure 12 on page 23. Notes 3. Pin Types: I = Input, O = Output, P = Power/Ground., Z = High Impedance, RDN = Pad internal Pull Down Resistor, RUP = Pad internal Pull Up Resistor. 4. PWR#/I2C_SDA can be used as either PWR# or I2C_SDA but not as both. If EEPROM is connected then the pin will act as I2C_SDA, it will not switch to PWR# mode (as it does in 48-pin TQFP package). 5. In Gang mode, only OVR#1 (pin 25) is enabled. Document Number: 001-67568 Rev. *H Page 14 of 28 CY7C65632, CY7C65634 EEPROM Configuration Options Systems using CY7C6563X have the option of using the default descriptors to configure the hub. Otherwise, it must have an external EEPROM for the device to have a unique VID, and PID. The CY7C6563X can communicate with an SPI (microwire) EEPROM like 93C46 or I2C EEPROM like 24C02. Example EEPROM connections are as shown in the following figure. Figure 8. EEPROM Connections SPI EEPROM Connection VDD Table 1. EEPROM Configuration Options (continued) Byte Value 09h–0Fh Reserved - FFh 10h Vendor String Length 11h–3Fh Vendor String (ASCII code) 40h Product String Length 41h–6Fh Product String (ASCII Code) 70h Serial Number Length 71h to 80h onwards Serial Number String AMBER#[1] CS VCC GREEN#[1] SK NC1 Default VID is 0x4B4, PID is 0x6570. AMBER#[2] DI NC2 Byte 0: VID (LSB) GREEN#[2] DO GND Least Significant Byte of Vendor ID Byte 1: VID (MSB) AT93C46 Most Significant Byte of Vendor ID I2C EEPROM Connection A0 VDD Byte2: PID (LSB) Least Significant Byte of Product ID VCC Byte 3: PID (MSB) A1 WP A2 SCL TEST GND SDA PWR#[1] Most Significant Byte of Product ID Byte 4: ChkSum CY7C6563X will ignore the EEPROM settings if ChkSum is not equal to VID_LSB + VID_MSB + PID_LSB + PID_MSB +1 AT24C02 Byte 5: Reserved Note The 28-pin QFN package includes only support for I2C EEPROM like ATMEL/24C02N_SU27 D, MICROCHIP/4LC028 SN0509, SEIKO/S24CS02AVH9. The 48-pin TQFP package includes both I2C and SPI EEPROM connectivity options. In this case, user can use either SPI or I2C connectivity at a time for communicating to EEPROM. The 48-pin package supports ATMEL/AT93C46DN-SH-T, in addition to the above mentioned families. HX2VL can only read from SPI EEPROM. So, field programming of EEPROM is supported only for I2C EEPROM. CY7C6563X verifies the check sum after power on reset and if validated loads the configuration from the EEPROM. To prevent this configuration from being overwritten, AMBER[1] is disabled when SPI EEPROM is present. Table 1. EEPROM Configuration Options Byte Value 00h VID_LSB 01h VID_MSB 02h PID_LSB 03h PID_MSB 04h ChkSum 05h Reserved - FEh 06h Removable Ports 07h Port Number 08h Maximum Power Document Number: 001-67568 Rev. *H Set to FEh Byte 6: RemovablePorts RemovablePorts[4:1] are the bits that indicates whether the device attached to the corresponding downstream port is removable (set to 0) or non-removable (set to 1). Bit 1 corresponds to Port 1, Bit 2 to Port 2 and so on. Default value is 0 (removable). These bit values are reported appropriately in the HubDescriptor:DeviceRemovable field. Bits 0,5,6,7 are set to 0. Byte 7: Port Number Port Number indicates the number of downstream ports. The values must be 1 to 4. Default value is 4. Byte 8: Maximum Power This value is reported in the Configuration Descriptor: bMax-Power field and is the current in 2 mA increments that is required from the upstream hubs. The allowed range is 00h (0 mA) to FAh(500 mA). Default value is 32h (100mA). Byte 9–15: Reserved Set to FFh Byte 16: Vendor String Length Length of the Vendor String Byte 17–63: Vendor String Value of Vendor String. Page 15 of 28 CY7C65632, CY7C65634 Figure 10. Power Switching Mode Byte 64: Product String Length Length of the Product String VDD (3.3V) Byte 65–111: Product String VDD (3.3V) PCB Silicon GANG MODE Value of Product String. 100K GANG/SUSPEND Byte 112: Serial Number Length Length of the Serial Number SUSPEND OUT SUSPEND INDICATOR Byte 113 onwards: Serial Number String Serial Number String. 100K Pin Configuration Options 0 : INDIVIDUAL MODE 1: GANG MODE INDIVIDUAL MODE Power ON Reset The power on reset can be triggered by external reset or internal circuitry. The internal reset is initiated, when there is an unstable power event for silicon’s internal core power (3.3 V ± 10%). The internal reset is released 2.7 µs± 1.2% after supply reaches power good voltage (2.5 V to 2.8 V). The external reset pin, continuously senses the voltage level (5 V) on the upstream VBUS as shown in the figure. In the event of USB plug/unplug or drop in voltage, the external reset is triggered. This reset trigger can be configured using the resistors R1 and R2. Cypress recommends that the reset time applied in external reset circuit should be longer than that of the internal reset time. Table 2. Features Supported in 48-pin and 28-pin Packages Figure 9. Power ON Reset Circuit Power Switch Enable Pin Polarity PCB VBUS (External 5V) Silicon R1 Ext. VBUS power-good detection circuit input (Pin"RESET#") EXT R2 INT Global Reset# Int. 3.3V power-good detection circuit input (USB PHY reset) 48 Pin 28 Pin Port number configuration Supported Features Yes No Non-Removable port configuration Yes No Reference clock configuration Yes No Power switch enable polarity Yes No LED Indicator Yes No The pin polarity is set Active-High by pin-strapping the PWR_PIN_POL pin to 1 and Active-Low by pin-strapping the PWR_PIN_POL pin to 0. Thus, both kinds of power switches are supported. This feature is not supported in 28-pin QFN package. Port Number Configuration In addition to the EEPROM configuration, as described above, configuring the hub for 2/3/4 ports is also supported using pin-strapping SET_PORT_NUM1 and SET_PORT_NUM2, as shown in following table. Pin strapping option is not supported in the 28-pin QFN package. Table 3. Port Number Configuration using Pinstrap Gang/Individual Power Switching Mode A single pin is used to set individual / gang mode as well as output the suspend flag. This is done to reduce the pin count. The individual or gang mode is decided within 20 µs after power on reset. It has a setup time of 1 ns. 50 to 60 ms after reset, this pin is changed to output mode. CY7C6563X outputs the suspend flag, after it is globally suspended. Pull-down resistor of greater than 100K is needed for Individual mode and a pull-up resistor greater than 100K is needed for Gang mode. Figure below shows the suspend LED indicator schematics. The polarity of LED must be followed, otherwise the suspend current will be over the spec limitation (2.5 mA). Document Number: 001-67568 Rev. *H SET_PORT_NUM2 SET_PORT_NUM1 # Ports 1 1 1 (Port 1) 1 0 2 (Port 1/2) 0 1 3 (Port 1/2/3) 0 0 4 (All ports) Non Removable Ports Configuration In embedded systems, downstream ports that are always connected inside the system, can be set as non-removable (always connected) ports, by pin-strapping the corresponding FIXED_PORT# pins 1~4 to High, before power on reset. At POR, if the pin is pull high, the corresponding port is set to non-removable. This is not supported in the 28-pin QFN package. Page 16 of 28 CY7C65632, CY7C65634 Reference Clock Configuration This hub can support, optional 27/48 MHz clock source. When on-board 27/48 MHz clock is present, then using this feature, system integrator can further reduce the BOM cost by eliminating the external crystal. This is available through GPIO pin configuration shown as follows. This is not supported in the 28-pin QFN package. Table 4. Reference Clock Options SEL48 SEL27 Clock Source 0 1 48 MHz OSC-in 1 0 27 MHz OSC-in 1 1 12 MHz X’tal/OSC-in Document Number: 001-67568 Rev. *H Page 17 of 28 CY7C65632, CY7C65634 Absolute Maximum Ratings Operating Conditions Exceeding maximum ratings may shorten the useful life of the device. User guidelines are not tested. Ambient temperature ..................................... 0 °C to +70 °C Storage temperature ................................ –55 °C to +100 °C 5 V supply voltage to ground potential ......4.75 V to +5.25 V Ambient temperature ..................................... 0 °C to +70 °C Ambient max junction temperature .............. 0 °C to +125 °C 3.3 V supply voltage to ground potential .....3.15 V to +3.6 V 5 V supply voltage to ground potential ........–0.5 V to +6.0 V Input voltage for USB signal pins ..................0.5 V to +3.6 V 3.3 V supply voltage to ground potential .....–0.5 V to +3.6 V Voltage at open drain input pins ..................–0.5 V to +5.0 V Voltage at open drain input pins (OVR#1-4, SELFPWR, RESET#) ................–0.5 V to +5.5 V Thermal characteristics 48-pin TQFP ................... 78.7 °C/W Thermal characteristics 28-pin QFN ..................... 33.3 °C/W 3.3 V input voltage for digital I/O ..................–0.5 V to +3.6 V FOSC (oscillator or crystal frequency) ........ 12 MHz ± 0.05% Electrical Characteristics DC Electrical Characteristics Max Parameter Description Conditions Min Typ External regulator Internal regulator PD Power dissipation Excluding USB signals 366.5 – VIH Input high voltage – 2 – – VIL Input low voltage – – – 0.8 Full speed / Low speed (0 < VIN < VCC) –10 – +10 High speed mode (0 < VIN < VCC) –5 0 +5 Il Input leakage current 426.5 Output voltage high IOH = 8 mA 2.4 – – VOL Output low voltage IOL= 8 mA – – 0.4 RDN Pad internal pull-down Resistor – 29 59 135 RUP Pad internal pull-up Resistor – 80 108 140 CIN Input pin capacitance Full speed / Low speed mode – – 20 High speed mode 4 4.5 5 – 0.786 Suspend current – mW V A VOH ISUSP Unit 1.043 V K pF 1.3 mA Notes 6. Current measurement is with device attached and enumerated. 7. No devices attached. Document Number: 001-67568 Rev. *H Page 18 of 28 CY7C65632, CY7C65634 Electrical Characteristics (continued) DC Electrical Characteristics (continued) Max Parameter Description Conditions Min Typ External regulator Internal regulator Full speed host, full speed devices – 88.7 103.9 105.4 High speed host, high speed devices – 81.9 88.2 89.3 High speed host, full speed devices – 88.2 101.2 102.3 Full speed host, full speed devices – 79.1 91.6 93 High speed host, high speed devices – 72.9 78.5 78.6 High speed host, full speed devices – 75.9 88.7 88.8 Full speed host, full speed devices – 68.1 78.4 78.6 High speed host, high speed devices – 61.9 67.6 69.6 High speed host, full speed devices – 64.9 75.4 76.1 Full speed host, full speed devices – 57.1 66.3 66.7 High speed host, high speed devices – 51.9 57.6 59.3 High speed host, full speed devices – 54.7 61.1 62.5 Unit Supply Current 4 Active ports[6] 3 Active ports ICC 2 Active ports 1 Active port No Active Ports[7] Full speed host – 42.8 48.9 50.3 High speed host – 44.2 49.1 50.6 mA Notes 6. Current measurement is with device attached and enumerated. 7. No devices attached. Document Number: 001-67568 Rev. *H Page 19 of 28 CY7C65632, CY7C65634 AC Electrical Characteristics USB Transceiver is USB 2.0 certified in low, full and high speed modes. Both the upstream USB transceiver and all four downstream transceivers have passed the USB-IF USB 2.0 Electrical Certification Testing. The 48-pin TQFP package can support communication to EEPROM using either I2C or SPI. The 28-pin QFN package can support only I2C communication to EEPROM. AC Characteristics of these two interfaces to EEPROM are summarized in tables below: AC Characteristics of SPI EEPROM Interface Parameter Parameter Min Typ Max tCSS CS setup time 3.0 – – tCSH CS hold time 3.0 – – tSKH SK high time 1.0 – – tSKL SK low time 2.2 – – tDIS DI setup time 1.8 – – tDIH DI hold time 2.4 – – tPD1 Output delay to ‘1’ – – 1.8 tPD0 Output delay to ‘0’ – – 1.8 Units µs AC Characteristics of I2C EEPROM Interface Parameter Parameter 1.8 V–5.5 V 2.5 V–5.5 V Min Max Min Max Units fSCL SCL clock frequency 0.0 100 0.0 400 tLOW Clock LOW Period 4.7 – 1.2 – tHIGH Clock HIGH Period 4.0 – 0.6 – tSU:STA Start condition setup time 4.7 – 0.6 – tSU:STO Stop condition setup time 4.7 – 0.6 – tHD:STA Start condition hold time 4.0 – 0.6 – tHD:STO Stop condition hold time 4.0 – 0.6 – tSU:DAT Data in setup time 200.0 – 100.0 – tHD:DAT Data in hold time 0 – 0 – tDH Data out hold time 100 – 50 – tAA Clock to output 0.1 4.5 0.1 – µs tWR Write cycle time – 10 – 5 ns kHz µs ns Thermal Resistance Parameter Description 48-pin TQFP Package 28-pin QFN Package JA Thermal resistance (junction to ambient) 78.7 33.3 JC Thermal resistance (junction to case) 35.3 18.4 Document Number: 001-67568 Rev. *H Unit °C/W Page 20 of 28 CY7C65632, CY7C65634 Ordering Information Ordering Code Device Package Type CY7C65632-48AXC 4 port Single-TT hub (configurable with GPIOs and EEPROM) 48-pin TQFP Bulk CY7C65632-28LTXC 4 port Single-TT hub (configurable with GPIOs and EEPROM) 28-pin QFN Bulk CY7C65632-48AXCT 4 port Single-TT hub (configurable with GPIOs and EEPROM) 48-pin TQFP Tape and Reel CY7C65632-28LTXCT 4 port Single-TT hub (configurable with GPIOs and EEPROM) 28-pin QFN Tape and Reel CY7C65634-48AXC 2 port Single-TT hub (configurable with GPIOs and EEPROM) 48-pin TQFP Bulk CY7C65634-28LTXC 2 port Single-TT hub (configurable with GPIOs and EEPROM) 28-pin QFN Bulk CY7C65634-48AXCT 2 port Single-TT hub (configurable with GPIOs and EEPROM) 48-pin TQFP Tape and Reel CY7C65634-28LTXCT 2 port Single-TT hub (configurable with GPIOs and EEPROM) 28-pin QFN Tape and Reel Ordering Code Definitions CY 7 C 656 3X - XX XX X C X X = T or blank T = Tape and Reel; blank = Bulk Temperature Grade: C = Commercial Pb-free Package Type: XX = A or LT A = TQFP LT = QFN Pin Count: XX = 48 or 28 48 = 48 pins, 28 = 28 pins Specific Product Identifier: 3X = 32 or 34 Part Identifier Technology Code: C = CMOS Marketing Code Company ID: CY = Cypress Document Number: 001-67568 Rev. *H Page 21 of 28 CY7C65632, CY7C65634 Package Diagrams The CY7C65632 is available in following packages: Figure 11. 48-pin TQFP (7 × 7 × 1.4 mm) A48 Package Outline, 51-85135 51-85135 *C Document Number: 001-67568 Rev. *H Page 22 of 28 CY7C65632, CY7C65634 Package Diagrams (continued) The CY7C65632 is available in following packages: Figure 12. 28-pin QFN (5 × 5 × 0.8 mm), LT28A (3.5 × 3.5 E-Pad), Sawn Package Outline, 001-64621 001-64621 *A Document Number: 001-67568 Rev. *H Page 23 of 28 CY7C65632, CY7C65634 Acronyms Acronym Document Conventions Description AC alternating current ASCII american standard code for information interchange EEPROM Units of Measure Symbol Unit of Measure °C degree Celsius electrically erasable programmable read only memory kHz kilohertz k kilohm EMI electromagnetic interference MHz megahertz ESD electrostatic discharge A microampere GPIO general purpose input/output s microsecond I/O input/output W microwatt LED light emitting diode mA milliampere LSB least significant bit mm millimeter MSB most significant bit ms millisecond PCB printed circuit board mW milliwatt PLL phase-locked loop ns nanosecond POR power on reset PSoC® ohm Programmable System-on-Chip™ % percent QFN quad flat no leads pF picofarad RAM random access memory ppm parts per million ROM read only memory V volt SIE serial interface engine W watt TQFP thin quad flat pack TT transaction translator USB universal serial bus Document Number: 001-67568 Rev. *H Page 24 of 28 CY7C65632, CY7C65634 Silicon Errata for the HX2VL, CY7C65632 Product Family This section describes the errata for the HX2VL, CY7C65632. The details include errata trigger conditions, scope of impact, available workarounds, and silicon revision applicability. Contact your local Cypress Sales Representative, if you have any questions. Part Numbers Affected Part Number Device Characteristics CY7C65632 USB 2.0 Single TT Hub HX2VL Qualification Status Product Status: In production HX2VL Errata Summary This is the initial version of the HX2VL Errata. As of now, there is no known issue with respect to the HX2VL. Document Number: 001-67568 Rev. *H Page 25 of 28 CY7C65632, CY7C65634 Document History Page Document Title: CY7C65632/CY7C65634, HX2VL™ Very Low Power USB 2.0 Hub Controller Document Number: 001-67568 Revision ECN Orig. of Change Submission Date ** 3183649 SSJO / SWAK 03/02/2011 New data sheet. *A 3250883 SWAK / AASI 05/06/2011 Updated Functional Overview (Updated Port Indicators (Added a Note “Pin-strapping GREEN#[1] and GREEN#[2] enables proprietary function that may affect the normal functionality of HX2VL. Configuring Port #1 and #2 as non-removable by pin-strapping should be avoided.”). Updated Pin Configurations (Updated Figure 4 and Figure 5 (Pin 37 of the 48-pin TQFP package was named SELF_PWR. It is changed to SELFPWR.)). Updated Pin Definitions (changed value from 680 to 650 in description of RREF pin). Updated Functional Overview (Updated Power Regulator on page 6 (Changed regulator’s maximum current loading from 200 mA to 150 mA)). Updated Pin Configuration Options (Updated Power Switch Enable Pin Polarity (Replaced first two occurrences of the word “setting” with “pin-strapping”)). Updated Electrical Characteristics (Updated DC Electrical Characteristics (Changed typical value of ISUSP parameter from 693.3 µA to 786 µA, changed maximum value of ISUSP parameter 693.7 µA to 903 µA, and updated typical and maximum values of ICC parameter)). *B 3324484 AASI 07/25/2011 Changed status from Preliminary to Final. Updated Pin Configurations (Included CY7C65634 related information). Updated Pin Definitions (Changed description of OVR# pins from “Default is Active LOW” to “Active LOW Overcurrent Condition Detection Input” (since the polarity is not configurable)). Updated Pin Definitions (Changed description of OVR# pins from “Default is Active LOW” to “Active LOW Overcurrent Condition Detection Input” (since the polarity is not configurable)). Updated Electrical Characteristics (Updated DC Electrical Characteristics (Updated minimum, typical, and maximum values of RDN and RUP parameters to 81 k103 k and 181 k)). *C 3336689 SWAK 08/04/2011 No technical updates. *D 3412885 AASI 10/18/2011 Updated Pin Configurations (Updated Figure 4 and Figure 5 (Renamed SPI_DI to SPI_MOSI, renamed SPI_DO to SPI_MISO respectively for clarity), updated Figure 6 (Updated pin 26 to describe the alternate function I2C_SDA.), updated Figure 7 (Updated to reflect pin 20 as NC)). Updated Pin Definitions (Renamed SPI_DI to SPI_MOSI, renamed SPI_DO to SPI_MISO respectively for clarity). Updated Pin Definitions (Added Note 3 and referred the same note in PWR#). Minor text edits to add clarity. *E 3508597 AASI 01/25/2011 Updated EEPROM Configuration Options (Removed text, “Strings must comply with the USB specification. The first byte (Byte 16) must be the length of the string in bytes, the second must be 0x03, and the string must be in ASCII code.” below “Vendor string”, “Product string” and “Serial Number string”.). Updated Functional Overview (Updated Overcurrent Detection (Included the text, “OVR#[n] has a setup time of 20 ns. It takes 3 to 4 ms from overcurrent detection to de-assertion of PWR#[n].”). Document Number: 001-67568 Rev. *H Description of Change Page 26 of 28 CY7C65632, CY7C65634 Document History Page (continued) Document Title: CY7C65632/CY7C65634, HX2VL™ Very Low Power USB 2.0 Hub Controller Document Number: 001-67568 Revision ECN Orig. of Change Submission Date Description of Change *F 3660597 AASI 07/02/2012 Updated EEPROM Configuration Options (Changed the value of Byte 5 to FEh to match with the tabular column). Updated Electrical Characteristics (Updated DC Electrical Characteristics (Splitted the Max column into two columns namely External regulator and Internal regulator for ISUSP and ICC parameters and updated the corresponding values)). Added Thermal Resistance. Updated in new template. *G 3995708 PRJI 05/09/2013 Added Silicon Errata for the HX2VL, CY7C65632 Product Family. *H 4661191 PRJI 02/17/2015 Added More Information. Removed the note in Port Indicators. Updated the term “LOW” to “HIGH” in LED descriptions, in Pin Definitions as LEDs are active HIGH by default. Added Note 1 and 2, and referred it in Pin Definitions. Updated RDN and RDUP values in DC Electrical Characteristics. Added Note 5 for GANG pin in DC Electrical Characteristics. Added Note 6 and 7 for Active ports and No active ports, and referred it in DC Electrical Characteristics. Updated Figure 11 (spec 51-85135 *B to *C) and Figure 12 (spec 001-64621 ** to *A) in Package Diagrams. Updated the Production Status “Sampling” to “In production” in HX2VL Qualification Status. Document Number: 001-67568 Rev. *H Page 27 of 28 CY7C65632, CY7C65634 Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. PSoC® Solutions Products Automotive Clocks & Buffers Interface Lighting & Power Control Memory PSoC Touch Sensing USB Controllers Wireless/RF cypress.com/go/automotive cypress.com/go/clocks cypress.com/go/interface cypress.com/go/powerpsoc cypress.com/go/memory cypress.com/go/psoc cypress.com/go/touch psoc.cypress.com/solutions PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP Cypress Developer Community Community | Forums | Blogs | Video | Training Technical Support cypress.com/go/support cypress.com/go/USB cypress.com/go/wireless © Cypress Semiconductor Corporation, 2011-2015. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Document Number: 001-67568 Rev. *H Revised February 17, 2015 All products and company names mentioned in this document may be the trademarks of their respective holders. Page 28 of 28