APTM100DA18TG Boost chopper MOSFET Power Module Application AC and DC motor control Switched Mode Power Supplies Power Factor Correction NTC2 VBUS VBUS SENSE CR1 Features Power MOS 7® MOSFETs - Low RDSon - Low input and Miller capacitance - Low gate charge - Avalanche energy rated - Very rugged Kelvin source for easy drive Very low stray inductance - Symmetrical design - Lead frames for power connections Internal thermistor for temperature monitoring High level of integration OUT Q2 G2 S2 0/VBU S VDSS = 1000V RDSon = 180m typ @ Tj = 25°C ID = 43A @ Tc = 25°C NTC1 Benefits Outstanding performance at high frequency operation Direct mounting to heatsink (isolated package) Low junction to case thermal resistance Solderable terminals both for power and signal for easy PCB mounting Low profile RoHS Compliant Absolute maximum ratings ID IDM VGS RDSon PD IAR EAR EAS Parameter Drain - Source Breakdown Voltage Tc = 25°C Tc = 80°C Continuous Drain Current Pulsed Drain current Gate - Source Voltage Drain - Source ON Resistance Maximum Power Dissipation Avalanche current (repetitive and non repetitive) Repetitive Avalanche Energy Single Pulse Avalanche Energy Tc = 25°C Max ratings 1000 43 33 172 ±30 210 780 25 50 3000 Unit V A V m W A mJ These Devices are sensitive to Electrostatic Discharge. Proper Handling Procedures Should Be Followed. See application note APT0502 on www.microsemi.com www.microsemi.com 1–7 APTM100DA18TG– Rev 3 October, 2012 Symbol VDSS APTM100DA18TG All ratings @ Tj = 25°C unless otherwise specified Electrical Characteristics Symbol Characteristic IDSS RDS(on) VGS(th) IGSS Zero Gate Voltage Drain Current Drain – Source on Resistance Gate Threshold Voltage Gate – Source Leakage Current Test Conditions Min VGS = 0V,VDS = 1000V Tj = 25°C VGS = 0V,VDS = 800V Tj = 125°C VGS = 10V, ID = 21.5A VGS = VDS, ID = 5mA VGS = ±30 V, VDS = 0V Typ 180 3 Max 200 1000 210 5 ±150 Unit Max Unit µA m V nA Dynamic Characteristics Symbol Ciss Coss Crss Characteristic Input Capacitance Output Capacitance Reverse Transfer Capacitance Test Conditions VGS = 0V VDS = 25V f = 1MHz Qg Total gate Charge Qgs Gate – Source Charge Qgd Gate – Drain Charge VGS = 10V VBus = 500V ID = 43A Td(on) Turn-on Delay Time Tr Td(off) Rise Time Turn-off Delay Time Tf Fall Time Eon Turn-on Switching Energy Eoff Turn-off Switching Energy Eon Turn-on Switching Energy Eoff Turn-off Switching Energy Min Typ 10.4 1.76 0.32 nF 372 nC 48 244 18 Inductive switching @ 125°C VGS = 15V VBus = 670V ID = 43A RG = 2.5 12 ns 155 40 Inductive switching @ 25°C VGS = 15V, VBus = 670V ID = 43A, RG = 2.5Ω 1800 Inductive switching @ 125°C VGS = 15V, VBus = 670V ID = 43A, RG = 2.5Ω 2846 µJ 1246 µJ 1558 Chopper diode ratings and characteristics IRM Maximum Reverse Leakage Current IF DC Forward Current VF Diode Forward Voltage trr Reverse Recovery Time Qrr Reverse Recovery Charge Test Conditions VR=1000V Min 1000 Tj = 25°C Tj = 125°C IF = 60A VR = 670V di/dt = 200A/µs www.microsemi.com Max 250 500 Tj = 125°C 60 1.9 2.2 1.7 Tj = 25°C 280 Tj = 125°C 350 Tj = 25°C 760 Tj = 125°C 3600 Tc = 100°C IF = 60A IF = 120A IF = 60A Typ Unit V µA A 2.5 V ns nC 2–7 APTM100DA18TG– Rev 3 October, 2012 Symbol Characteristic VRRM Maximum Peak Repetitive Reverse Voltage APTM100DA18TG Thermal and package characteristics Symbol Characteristic RthJC VISOL TJ TSTG TC Torque Wt Min Junction to Case Thermal Resistance RMS Isolation Voltage, any terminal to case t =1 min, 50/60Hz Operating junction temperature range Storage Temperature Range Operating Case Temperature Mounting torque Package Weight Typ Transistor Diode To Heatsink M5 4000 -40 -40 -40 2.5 Max 0.16 0.9 Unit °C/W V 150 125 100 4.7 160 °C N.m g Temperature sensor NTC (see application note APT0406 on www.microsemi.com for more information). Symbol Characteristic R25 Resistance @ 25°C B 25/85 T25 = 298.15 K RT Min Typ 50 3952 Max Unit k K R25 T: Thermistor temperature 1 1 RT: Thermistor value at T exp B25 / 85 T25 T ALL DIMENSIONS MARKED " * " ARE TOLERENCED AS : See application note APT0501 - Mounting Instructions for SP4 Power Modules on www.microsemi.com www.microsemi.com 3–7 APTM100DA18TG– Rev 3 October, 2012 SP4 Package outline (dimensions in mm) APTM100DA18TG Typical Performance Curve Maximum Effective Transient Thermal Impedance, Junction to Case vs Pulse Duration Thermal Impedance (°C/W) 0.18 0.16 0.9 0.14 0.7 0.12 0.1 0.5 0.08 0.3 0.06 0.04 0.1 0.05 0.02 Single Pulse 0 0.00001 0.0001 0.001 0.01 0.1 1 10 rectangular Pulse Duration (Seconds) Low Voltage Output Characteristics Transfert Characteristics 160 VGS=15, 10&8V 100 7V 80 6.5V 60 6V 40 5.5V 20 120 100 80 60 0 5 10 15 20 25 TJ=25°C 40 20 5V 0 VDS > ID(on)xRDS(on)MAX 250µs pulse test @ < 0.5 duty cycle 140 ID, Drain Current (A) TJ=125°C 30 0 ID, DC Drain Current (A) RDS(on) Drain to Source ON Resistance VGS=10V 1.1 VGS=20V 1 3 4 5 6 7 8 9 45 Normalized to VGS=10V @ 21.5A 1.2 2 DC Drain Current vs Case Temperature RDS(on) vs Drain Current 1.3 1 VGS, Gate to Source Voltage (V) VDS, Drain to Source Voltage (V) 1.4 TJ=-55°C 0 0.9 40 35 30 25 20 15 10 0.8 5 0 0 20 40 60 80 100 120 ID, Drain Current (A) 25 50 75 100 125 150 TC, Case Temperature (°C) www.microsemi.com 4–7 APTM100DA18TG– Rev 3 October, 2012 ID, Drain Current (A) 120 1.10 1.05 1.00 0.95 0.90 0.85 -50 -25 0 25 50 75 100 125 150 ON resistance vs Temperature 2.5 VGS=10V ID=21.5A 2.0 1.5 1.0 0.5 0.0 -50 -25 TJ, Junction Temperature (°C) Threshold Voltage vs Temperature 50 75 100 125 150 Maximum Safe Operating Area 1.1 100µs ID, Drain Current (A) VGS(TH), Threshold Voltage (Normalized) 25 1000 1.2 1.0 0.9 0.8 0.7 limited by RDSon 100 1ms 10 Single pulse TJ=150°C TC=25°C 10ms 1 0.6 1 -50 -25 0 25 50 75 100 125 150 TC, Case Temperature (°C) Capacitance vs Drain to Source Voltage Ciss 10000 Coss 1000 Crss 100 0 10 20 30 40 10 100 1000 VDS, Drain to Source Voltage (V) Gate Charge vs Gate to Source Voltage VGS, Gate to Source Voltage (V) 100000 C, Capacitance (pF) 0 TJ, Junction Temperature (°C) 14 ID=43A TJ=25°C 12 VDS=500V 10 50 VDS, Drain to Source Voltage (V) VDS=200V VDS=800V 8 6 4 2 0 0 100 200 300 400 500 Gate Charge (nC) www.microsemi.com 5–7 APTM100DA18TG– Rev 3 October, 2012 BVDSS, Drain to Source Breakdown Voltage (Normalized) Breakdown Voltage vs Temperature 1.15 RDS(on), Drain to Source ON resistance (Normalized) APTM100DA18TG APTM100DA18TG Delay Times vs Current Rise and Fall times vs Current 80 td(off) 160 VDS=670V RG=2.5Ω TJ=125°C L=100µH 120 80 40 tr 0 0 10 30 50 70 90 10 ID, Drain Current (A) Eon VDS=670V RG=2.5Ω TJ=125°C L=100µH Eoff 2 1 5 4 2 Eoff 1 30 50 70 90 0 ID, Drain Current (A) 5 10 15 20 Gate Resistance (Ohms) Operating Frequency vs Drain Current Source to Drain Diode Forward Voltage 1000 ZCS ZVS 150 VDS=670V D=50% RG=2.5Ω TJ=125°C Tc=75°C Hard switching 100 TJ=25°C 10 0 10 15 20 25 30 35 ID, Drain Current (A) TJ=150°C 40 1 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 VSD, Source to Drain Voltage (V) www.microsemi.com 6–7 APTM100DA18TG– Rev 3 October, 2012 200 IDR, Reverse Drain Current (A) 250 Frequency (kHz) Eon 3 0 10 50 Eoff VDS=670V ID=43A TJ=125°C L=100µH 6 0 100 90 7 Switching Energy (mJ) Switching Energy (mJ) 3 30 50 70 ID, Drain Current (A) Switching Energy vs Gate Resistance Switching Energy vs Current 5 4 tf 20 td(on) 40 VDS=670V RG=2.5Ω TJ=125°C L=100µH 60 tr and tf (ns) td(on) and td(off) (ns) 200 APTM100DA18TG DISCLAIMER The information contained in the document (unless it is publicly available on the Web without access restrictions) is PROPRIETARY AND CONFIDENTIAL information of Microsemi and cannot be copied, published, uploaded, posted, transmitted, distributed or disclosed or used without the express duly signed written consent of Microsemi. If the recipient of this document has entered into a disclosure agreement with Microsemi, then the terms of such Agreement will also apply. This document and the information contained herein may not be modified, by any person other than authorized personnel of Microsemi. No license under any patent, copyright, trade secret or other intellectual property right is granted to or conferred upon you by disclosure or delivery of the information, either expressly, by implication, inducement, estoppels or otherwise. Any license under such intellectual property rights must be approved by Microsemi in writing signed by an officer of Microsemi. Microsemi reserves the right to change the configuration, functionality and performance of its products at anytime without any notice. This product has been subject to limited testing and should not be used in conjunction with lifesupport or other mission-critical equipment or applications. Microsemi assumes no liability whatsoever, and Microsemi disclaims any express or implied warranty, relating to sale and/or use of Microsemi products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Any performance specifications believed to be reliable but are not verified and customer or user must conduct and complete all performance and other testing of this product as well as any user or customers final application. User or customer shall not rely on any data and performance specifications or parameters provided by Microsemi. It is the customer’s and user’s responsibility to independently determine suitability of any Microsemi product and to test and verify the same. The information contained herein is provided “AS IS, WHERE IS” and with all faults, and the entire risk associated with such information is entirely with the User. Microsemi specifically disclaims any liability of any kind including for consequential, incidental and punitive damages as well as lost profit. The product is subject to other terms and conditions which can be located on the web at http://www.microsemi.com/legal/tnc.asp Life Support Application Seller's Products are not designed, intended, or authorized for use as components in systems intended for space, aviation, surgical implant into the body, in other applications intended to support or sustain life, or for any other application in which the failure of the Seller's Product could create a situation where personal injury, death or property damage or loss may occur (collectively "Life Support Applications"). Buyer agrees not to use Products in any Life Support Applications and to the extent it does it shall conduct extensive testing of the Product in such applications and further agrees to indemnify and hold Seller, and its officers, employees, subsidiaries, affiliates, agents, sales representatives and distributors harmless against all claims, costs, damages and expenses, and attorneys' fees and costs arising, directly or directly, out of any claims of personal injury, death, damage or otherwise associated with the use of the goods in Life Support Applications, even if such claim includes allegations that Seller was negligent regarding the design or manufacture of the goods. www.microsemi.com 7–7 APTM100DA18TG– Rev 3 October, 2012 Buyer must notify Seller in writing before using Seller’s Products in Life Support Applications. Seller will study with Buyer alternative solutions to meet Buyer application specification based on Sellers sales conditions applicable for the new proposed specific part.