RECOMMENDED PCB LAYOUT (COMPONENT SIDE VIEW) EMPFOHLENES LEITERPLATTEN-LAYOUT (BESTUECKUNGSSEITE) TOL. 0.05 [0.002] UNLESS NOTED MAX RECOMMENDED PANEL CUTOUT EMPFOHLENER FRONTPLATTEN-AUSSCHNITT 1,27 0,050 0,635 0,025 PCB EDGE LP 0,89 14,72 0,580 0,38 ±0,10 0,015 ±0,004 21,59 0,850 16,66 0,656 ±0, 07 1,60 ± 0,07 3,25 ±0 ,07 2,54 0,100 0,03 5 0,06 ±0, 003 3 ±0,0 0,128 ± 0,003 03 X8 8 X2 1 X2 11,43±0,13 0,450 ±0,005 8 8,89 0,350 2,54 0,100 3,05 0,120 IMPROVED CONTACT DESIGN (PRE BEND) 13,63 0,537 1 3,20 ±0,20 0,126 ±0,008 15,88 0,625 11,43 0,450 15,49 0,610 10,89 0,429 1:1 NOTE 1: SIDE SHIELD TABS IN REAR 3.05 mm NOTE 2: PANEL GROUND FLANGES BOTH SIDES AND TOP (GF5) NOTE 3: RoHS COMPLIANT Mate ri al s & F i n i sh T e st D ata Stan d ard ap p l i c . Val u e Stan d ard ap p l i c . Val u e Insulation body Standard description PBT 30% Me c h ani c al p ro p e rti e s . Standard de scriptio n C5210 (acc. JIS) Inse rti o n/withdrawal fo rce IEC 603-7 Co ntact mate ri al max. 20 N Contact finish, mating zone Thickness of plating 30 µin Au over 50 µin Ni Mechanical operations IEC 512-5, 9a min. 1.000 Contact finish termination zone Thickness of plating 80 µin matte Sn over 50 µin Ni Effectiveness of connector co upli ng de vice IEC 512-8, 15f 50 N She ll/shi e ld mate ri al Standard de scriptio n C2680 (acc. JIS) Shell/shield plating Thickness of plating 50 µin Ni El e c tri c al p ro p e rti e s Cre e p ag e / c l e aran c e d i stan c e s A sse mb l y p ro c e ss a) Contact - contact IEC 807-3 0,52 mm P ackagi ng b) Co ntact - she ll min. 1, 0 mm T ray IEC 807-3 So lde r te mpe rature 235°C at 3-5s Vo l tag e p ro o f (Di e l e c tri c Wi thstan d Vo l tag e ) Suitable asse mbly pro ce ss wave IEC 512-2, 4a mi n. 1. 000 V AC/ DC a) Co ntact - co ntact b) Contact - shell/testpanel IEC 512-2, 4a min. 1.500 V AC/DC A p p ro v al s Current carrying capacity IEC 512-3, 5b 1,5 A @ 25° C UL i nsulatio n bo dy V0 Co ntact re sistance IEC 512-2, 2a max. 30 mOhm UL 94 UL Fi le N o . Insulati o n re sistance IEC 512-2, 3a E145613 mi n. 500 MOhm Ro HS co mpli ant Yes En v i ro n me n tal p ro p e rti e s Ope rati o n te mpe rature 0 - 70° C Copyright by ERNI GmbH Proprietary notice pursuant to ISO 16016 to be observed. T e chnical sp e cif icat io ns PART NO. IDENT. NR. TRANSMISSION REQUIREMENT ÜBERTRAGUNGSANFORDERUNG 133167 CATEGORY 5, DUAL TWIST PCB HOLE NUMBERING LP BOHRUNGSNUMERIERUNG 2 4 6 8 1 3 5 7 Tolerances Information: Scale 2:1 All Dimensions in mm[in] Designation All rights reserved. Only for Information. To insure that this is the latest version of this drawing, please contact one of the ERNI companies before using. E 05.07.2007 Index Date Subject to modification without prior notice. Drawing will not be updated. MOD JACK - MJR 8P8C, 1X1, CAT 5 133703 www.ERNI.com Class MJ I (1/1) A3