CY7C1380S CY7C1382S 18-Mbit (512 K × 36/1 M × 18) Pipelined SRAM 18-Mbit (512 K × 36/1 M × 18) Pipelined SRAM Features Functional Description ■ Supports bus operation up to 167 MHz ■ Available speed grade is 167 MHz ■ Registered inputs and outputs for pipelined operation ■ 3.3 V core power supply ■ 2.5 V or 3.3 V I/O power supply ■ Fast clock-to-output times ❐ 3.4 ns (for 167 MHz device) ■ Provides high-performance 3-1-1-1 access rate ■ User selectable burst counter supporting Intel Pentium® interleaved or linear burst sequences ■ Separate processor and controller address strobes ■ Synchronous self-timed write ■ Asynchronous output enable ■ Single cycle chip deselect ■ CY7C1380S available in JEDEC-standard Pb-free 100-pin TQFP and non Pb-free 165-ball FBGA package and CY7C1382S available in JEDEC-standard Pb-free 100-pin TQFP ■ IEEE 1149.1 JTAG-Compatible Boundary Scan ■ ZZ sleep mode option The CY7C1380S/CY7C1382S SRAM integrates 524,288 × 36 and 1,048,576 × 18 SRAM cells with advanced synchronous peripheral circuitry and a two-bit counter for internal burst operation. All synchronous inputs are gated by registers controlled by a positive edge triggered clock input (CLK). The synchronous inputs include all addresses, all data inputs, address-pipelining chip enable (CE1), depth-expansion chip enables (CE2 and CE3), burst control inputs (ADSC, ADSP, and ADV), write enables (BWX, and BWE), and global write (GW). Asynchronous inputs include the output enable (OE) and the ZZ pin. Addresses and chip enables are registered at rising edge of clock when address strobe processor (ADSP) or address strobe controller (ADSC) are active. Subsequent burst addresses can be internally generated as they are controlled by the advance pin (ADV). Address, data inputs, and write controls are registered on-chip to initiate a self-timed write cycle.This part supports byte write operations (see Pin Definitions on page 6 and Truth Table on page 9 for further details). Write cycles can be one to two or four bytes wide as controlled by the byte write control inputs. GW when active LOW writes all bytes. The CY7C1380S/CY7C1382S operates from a +3.3 V core power supply while all outputs operate with a +2.5 or +3.3 V power supply. All inputs and outputs are JEDEC-standard and JESD8-5-compatible. Selection Guide Description 167 MHz Unit Maximum Access Time 3.4 ns Maximum Operating Current 275 mA Maximum CMOS Standby Current 70 mA Cypress Semiconductor Corporation Document Number: 001-43822 Rev. *F • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised April 20, 2013 CY7C1380S CY7C1382S Logic Block Diagram – CY7C1380S A0, A1, A ADDRESS REGISTER 2 A [1:0] MODE ADV CLK Q1 BURST COUNTER CLR AND LOGIC ADSC Q0 ADSP BW D DQ D , DQP D BYTE WRITE REGISTER DQ D ,DQP D BYTE WRITE DRIVER BW C DQ C , DQP C BYTE WRITE REGISTER DQ C , DQP C BYTE WRITE DRIVER DQ B , DQP B BYTE WRITE REGISTER DQ B , DQP B BYTE WRITE DRIVER BW B GW CE 1 CE 2 CE 3 OE ZZ SENSE AMPS OUTPUT REGISTERS OUTPUT BUFFERS E DQs DQP A DQP B DQP C DQP D DQ A , DQP A BYTE WRITE DRIVER DQ A , DQP A BYTE WRITE REGISTER BW A BWE MEMORY ARRAY ENABLE REGISTER INPUT REGISTERS PIPELINED ENABLE SLEEP CONTROL Logic Block Diagram – CY7C1382S A0, A1, A ADDRESS REGISTER 2 BURST Q1 COUNTER AND LOGIC ADV CLK ADSC BW B DQ B, DQP B WRITE DRIVER DQ B, DQP B WRITE REGISTER MEMORY ARRAY BW A SENSE OUTPUT OUTPUT BUFFERS DQs DQP A DQP B DQ A, DQP A WRITE DRIVER DQ A, DQP A WRITE REGISTER BWE GW CE 1 CE2 CE3 INPUT ENABLE REGISTER PIPELINED ENABLE OE ZZ SLEEP CONTROL Document Number: 001-43822 Rev. *F Page 2 of 31 CY7C1380S CY7C1382S Contents Pin Configurations ........................................................... 4 Pin Definitions .................................................................. 6 Functional Overview ........................................................ 7 Single Read Accesses ................................................ 7 Single Write Accesses Initiated by ADSP ................... 7 Single Write Accesses Initiated by ADSC ................... 8 Burst Sequences ......................................................... 8 Sleep Mode ................................................................. 8 Interleaved Burst Address Table ................................. 8 Linear Burst Address Table ......................................... 8 ZZ Mode Electrical Characteristics .............................. 8 Truth Table ........................................................................ 9 Truth Table for Read/Write ............................................ 10 Truth Table for Read/Write ............................................ 10 IEEE 1149.1 Serial Boundary Scan (JTAG) .................. 11 Disabling the JTAG Feature ...................................... 11 Test Access Port (TAP) ............................................. 11 PERFORMING A TAP RESET .................................. 11 TAP REGISTERS ...................................................... 11 TAP Instruction Set ................................................... 11 Reserved ................................................................... 12 TAP Controller State Diagram ....................................... 13 TAP Controller Block Diagram ...................................... 14 TAP Timing ...................................................................... 15 TAP AC Switching Characteristics ............................... 15 3.3 V TAP AC Test Conditions ....................................... 16 3.3 V TAP AC Output Load Equivalent ......................... 16 Document Number: 001-43822 Rev. *F 2.5 V TAP AC Test Conditions ....................................... 16 2.5 V TAP AC Output Load Equivalent ......................... 16 TAP DC Electrical Characteristics and Operating Conditions ..................................................... 16 Identification Register Definitions ................................ 17 Scan Register Sizes ....................................................... 17 Identification Codes ....................................................... 17 Boundary Scan Order .................................................... 18 Maximum Ratings ........................................................... 19 Operating Range ............................................................. 19 Electrical Characteristics ............................................... 19 Capacitance .................................................................... 20 Thermal Resistance ........................................................ 20 AC Test Loads and Waveforms ..................................... 20 Switching Characteristics .............................................. 21 Switching Waveforms .................................................... 22 Ordering Information ...................................................... 26 Ordering Code Definitions ......................................... 26 Package Diagrams .......................................................... 27 Acronyms ........................................................................ 29 Document Conventions ................................................. 29 Units of Measure ....................................................... 29 Document History Page ................................................. 30 Sales, Solutions, and Legal Information ...................... 31 Worldwide Sales and Design Support ....................... 31 Products .................................................................... 31 PSoC Solutions ......................................................... 31 Page 3 of 31 CY7C1380S CY7C1382S Pin Configurations NC NC NC CY7C1382S (1 M × 18) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 Document Number: 001-43822 Rev. *F A NC NC VDDQ VSSQ NC DQPA DQA DQA VSSQ VDDQ DQA DQA VSS NC VDD ZZ DQA DQA VDDQ VSSQ DQA DQA NC NC VSSQ VDDQ NC NC NC A A A A A A A A A A 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 VDDQ VSSQ NC NC DQB DQB VSSQ VDDQ DQB DQB NC VDD NC VSS DQB DQB VDDQ VSSQ DQB DQB DQPB NC VSSQ VDDQ NC NC NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 MODE A A A A A1 A0 NC/72M NC/36M VSS VDD DQPB DQB DQB VDDQ VSSQ DQB DQB DQB DQB VSSQ VDDQ DQB DQB VSS NC VDD ZZ DQA DQA VDDQ VSSQ DQA DQA DQA DQA VSSQ VDDQ DQA DQA DQPA 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 CY7C1380S (512 K × 36) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 MODE A A A A A1 A0 NC/72M NC/36M VSS VDD A A A A A A A A DQPC DQC DQc VDDQ VSSQ DQC DQC DQC DQC VSSQ VDDQ DQC DQC NC VDD NC VSS DQD DQD VDDQ VSSQ DQD DQD DQD DQD VSSQ VDDQ DQD DQD DQPD A A CE1 CE2 NC NC BWB BWA CE3 VDD VSS CLK GW BWE OE ADSC ADSP ADV A A A A CE1 CE2 BWD BWC BWB BWA CE3 VDD VSS CLK GW BWE OE ADSC ADSP ADV A A Figure 1. Pin Diagram - 100-pin TQFP (14 × 20 × 1.4 mm) pinout (3 Chip Enable) Page 4 of 31 CY7C1380S CY7C1382S Pin Configurations (continued) Figure 2. 165-ball FBGA (13 × 15 × 1.4 mm) pinout (3 Chip Enable) CY7C1380S (512 K × 36) 1 A B C D E F G H J K L M N P NC/288M R 2 3 4 5 6 7 8 9 10 11 NC CE1 BWC BWB CE3 BWE ADSC ADV A NC/144M A CE2 BWD BWA CLK OE NC/576M NC DQC VDDQ VSS VDDQ VSS VDD VSS VSS VSS ADSP VDDQ A DQPC DQC GW VSS VDDQ NC/1G DQB DQPB DQB DQC DQC VDDQ VDD VSS VDDQ DQB DQB A VSS VSS VDD VSS VSS VDD DQC DQC VDDQ VDD VSS VSS VSS VDD VDDQ DQB DQB DQC NC DQD DQC NC DQD VDDQ NC VDDQ VDD VDD VDD VSS VSS VSS VSS VSS VSS VSS VSS VSS VDD VDD VDD VDDQ NC VDDQ DQB NC DQA DQB ZZ DQA DQD DQD VDDQ VDD VSS VSS VSS VDD VDDQ DQA DQA DQD DQD VDDQ VDD VSS VSS VSS VDD VDDQ DQA DQA DQD DQPD DQD NC VDDQ VDDQ VDD VSS VSS NC VSS A VSS NC VDD VSS VDDQ VDDQ DQA NC DQA DQPA NC NC/72M A A TDI A1 TDO A A A A MODE NC/36M A A TMS TCK A A A A Document Number: 001-43822 Rev. *F A0 Page 5 of 31 CY7C1380S CY7C1382S Pin Definitions Name I/O Description A0, A1, A InputAddress Inputs Used to Select One of the Address Locations. Sampled at the rising edge of the Synchronous CLK if ADSP or ADSC is active LOW, and CE1, CE2, and CE3 are sampled active. A1:A0 are fed to the two-bit counter. BWA, BWB, BWC, BWD InputByte Write Select Inputs, Active LOW. Qualified with BWE to conduct byte writes to the SRAM. Synchronous Sampled on the rising edge of CLK. GW InputGlobal Write Enable Input, Active LOW. When asserted LOW on the rising edge of CLK, a global Synchronous write is conducted (all bytes are written, regardless of the values on BWX and BWE). BWE InputByte Write Enable Input, Active LOW. Sampled on the rising edge of CLK. This signal must be Synchronous asserted LOW to conduct a byte write. CLK InputClock Clock Input. Used to capture all synchronous inputs to the device. Also used to increment the burst counter when ADV is asserted LOW, during a burst operation. CE1 InputChip Enable 1 Input, Active LOW. Sampled on the rising edge of CLK. Used in conjunction with Synchronous CE and CE to select or deselect the device. ADSP is ignored if CE is HIGH. CE is sampled only 2 3 1 1 when a new external address is loaded. CE2 InputChip Enable 2 Input, Active HIGH. Sampled on the rising edge of CLK. Used in conjunction with Synchronous CE1 and CE3 to select or deselect the device. CE2 is sampled only when a new external address is loaded. CE3 InputChip Enable 3 Input, Active LOW. Sampled on the rising edge of CLK. Used in conjunction with Synchronous CE1 and CE2 to select or deselect the device. CE3 is sampled only when a new external address is loaded. OE InputOutput Enable, Asynchronous Input, Active LOW. Controls the direction of the I/O pins. When Asynchronous LOW, the I/O pins behave as outputs. When deasserted HIGH, I/O pins are tri-stated, and act as input data pins. OE is masked during the first clock of a read cycle when emerging from a deselected state. ADV InputAdvance Input Signal, Sampled on the Rising Edge of CLK, Active LOW. When asserted, it Synchronous automatically increments the address in a burst cycle. ADSP InputAddress Strobe from Processor, Sampled on the Rising Edge of Clk, Active LOW. When Synchronous asserted LOW, addresses presented to the device are captured in the address registers. A1:A0 are also loaded into the burst counter. When ADSP and ADSC are both asserted, only ADSP is recognized. ASDP is ignored when CE1 is deasserted HIGH. ADSC InputAddress Strobe from Controller, Sampled on the Rising Edge of CLK, Active LOW. When Synchronous asserted LOW, addresses presented to the device are captured in the address registers. A1:A0 are also loaded into the burst counter. When ADSP and ADSC are both asserted, only ADSP is recognized. ZZ InputZZ Sleep Input. This active HIGH input places the device in a non-time critical sleep condition with Asynchronous data integrity preserved. For normal operation, this pin must be LOW or left floating. ZZ pin has an internal pull down. DQs, DQPX I/OBidirectional Data I/O Lines. As inputs, they feed into an on-chip data register that is triggered by Synchronous the rising edge of CLK. As outputs, they deliver the data contained in the memory location specified by the addresses presented during the previous clock rise of the read cycle. The direction of the pins is controlled by OE. When OE is asserted LOW, the pins behave as outputs. When HIGH, DQs and DQPX are placed in a tri-state condition. VDD Power Supply Power Supply Inputs to the Core of the Device. Document Number: 001-43822 Rev. *F Page 6 of 31 CY7C1380S CY7C1382S Pin Definitions (continued) Name VSS I/O Ground Description Ground for the Core of the Device. VSSQ I/O Ground Ground for the I/O Circuitry. VDDQ I/O Power Supply Power Supply for the I/O Circuitry. MODE Input-Static Selects Burst Order. When tied to GND selects linear burst sequence. When tied to VDD or left floating selects interleaved burst sequence. This is a strap pin and must remain static during device operation. Mode pin has an internal pull up. TDO JTAG serial Serial Data Out to the JTAG Circuit. Delivers data on the negative edge of TCK. If the JTAG feature output is not being utilized, this pin must be disconnected. This pin is not available on TQFP packages. Synchronous TDI JTAG serial Serial Data In to the JTAG Circuit. Sampled on the rising edge of TCK. If the JTAG feature is not input being utilized, this pin can be disconnected or connected to VDD. This pin is not available on TQFP Synchronous packages. TMS JTAG serial Serial Data In to the JTAG circuit. Sampled on the rising edge of TCK. If the JTAG feature is not input being utilized, this pin can be disconnected or connected to VDD. This pin is not available on TQFP Synchronous packages. TCK JTAGClock Clock Input to the JTAG circuitry. If the JTAG feature is not being utilized, this pin must be connected to VSS. This pin is not available on TQFP packages. NC – No Connects. 36M, 72M, 144M, 288M, 576M and 1G are address expansion pins and are not internally connected to the die. Functional Overview All synchronous inputs pass through input registers controlled by the rising edge of the clock. All data outputs pass through output registers controlled by the rising edge of the clock. Maximum access delay from the clock rise (tCO) is 3.4 ns (167 MHz device). The CY7C1380S/CY7C1382S supports secondary cache in systems utilizing a linear or interleaved burst sequence. The interleaved burst order supports Pentium® and i486 processors. The linear burst sequence is suited for processors that use a linear burst sequence. The burst order is user selectable, and is determined by sampling the MODE input. Accesses can be initiated with either the processor address strobe (ADSP) or the controller address strobe (ADSC). Address advancement through the burst sequence is controlled by the ADV input. A two-bit on-chip wraparound burst counter captures the first address in a burst sequence and automatically increments the address for the rest of the burst access. Byte write operations are qualified with the byte write enable (BWE) and byte write select (BWX) inputs. A global write enable (GW) overrides all byte write inputs and writes data to all four bytes. All writes are simplified with on-chip synchronous self-timed write circuitry. Three synchronous chip selects (CE1, CE2, CE3) and an asynchronous output enable (OE) provide for easy bank selection and output tri-state control. ADSP is ignored if CE1 is HIGH. Document Number: 001-43822 Rev. *F Single Read Accesses This access is initiated when the following conditions are satisfied at clock rise: (1) ADSP or ADSC is asserted LOW, (2) CE1, CE2, CE3 are all asserted active, and (3) the write signals (GW, BWE) are all deserted HIGH. ADSP is ignored if CE1 is HIGH. The address presented to the address inputs (A) is stored into the address advancement logic and the address register while being presented to the memory array. The corresponding data is allowed to propagate to the input of the output registers. At the rising edge of the next clock the data is allowed to propagate through the output register and onto the data bus within 3.4 ns (167 MHz device) if OE is active LOW. The only exception occurs when the SRAM is emerging from a deselected state to a selected state, its outputs are always tri-stated during the first cycle of the access. After the first cycle of the access, the outputs are controlled by the OE signal. Consecutive single read cycles are supported. After the SRAM is deselected at clock rise by the chip select and either ADSP or ADSC signals, its output tri-states immediately. Single Write Accesses Initiated by ADSP This access is initiated when both of the following conditions are satisfied at clock rise: (1) ADSP is asserted LOW, and (2) CE1, CE2, CE3 are all asserted active. The address presented to A is loaded into the address register and the address advancement logic while being delivered to the memory array. The write signals (GW, BWE, and BWX) and ADV inputs are ignored during this first cycle. Page 7 of 31 CY7C1380S CY7C1382S ADSP triggered write accesses require two clock cycles to complete. If GW is asserted LOW on the second clock rise, the data presented to the DQs inputs is written into the corresponding address location in the memory array. If GW is HIGH, then the write operation is controlled by BWE and BWX signals. The CY7C1380S/CY7C1382S provides byte write capability that is described in the write cycle descriptions table. Asserting the byte write enable input (BWE) with the selected byte write (BWX) input, selectively writes the desired bytes. Bytes not selected during a byte write operation remains unaltered. A synchronous self-timed write mechanism has been provided to simplify the write operations. The CY7C1380S/CY7C1382S is a common I/O device, the output enable (OE) must be deserted HIGH before presenting data to the DQs inputs. Doing so tri-states the output drivers. As a safety precaution, DQs are automatically tri-stated whenever a write cycle is detected, regardless of the state of OE. Single Write Accesses Initiated by ADSC ADSC write accesses are initiated when the following conditions are satisfied: (1) ADSC is asserted LOW, (2) ADSP is deserted HIGH, (3) CE1, CE2, CE3 are all asserted active, and (4) the appropriate combination of the write inputs (GW, BWE, and BWX) are asserted active to conduct a write to the desired byte(s). ADSC-triggered Write accesses require a single clock cycle to complete. The address presented to A is loaded into the address register and the address advancement logic while being delivered to the memory array. The ADV input is ignored during this cycle. If a global write is conducted, the data presented to the DQs is written into the corresponding address location in the memory core. If a byte write is conducted, only the selected bytes are written. Bytes not selected during a byte write operation remains unaltered. A synchronous self-timed write mechanism has been provided to simplify the write operations. The CY7C1380S/CY7C1382S is a common I/O device, the output enable (OE) must be deserted HIGH before presenting data to the DQs inputs. Doing so tri-states the output drivers. As a safety precaution, DQs are automatically tri-stated whenever a write cycle is detected, regardless of the state of OE. Burst Sequences The CY7C1380S/CY7C1382S provides a two-bit wraparound counter, fed by A1:A0, that implements an interleaved or a linear burst sequence. The interleaved burst sequence is designed specifically to support Intel Pentium applications. The linear burst sequence is designed to support processors that follow a linear burst sequence. The burst sequence is user selectable through the MODE input. Asserting ADV LOW at clock rise automatically increments the burst counter to the next address in the burst sequence. Both read and write burst operations are supported. Sleep Mode The ZZ input pin is an asynchronous input. Asserting ZZ places the SRAM in a power conservation sleep mode. Two clock cycles are required to enter into or exit from this sleep mode. While in this mode, data integrity is guaranteed. Accesses pending when entering the sleep mode are not considered valid nor is the completion of the operation guaranteed. The device must be deselected prior to entering the sleep mode. CE1, CE2, CE3, ADSP, and ADSC must remain inactive for the duration of tZZREC after the ZZ input returns LOW. Interleaved Burst Address Table (MODE = Floating or VDD) First Address A1:A0 00 01 10 11 Second Address A1:A0 01 00 11 10 Third Address A1:A0 10 11 00 01 Fourth Address A1:A0 11 10 01 00 Third Address A1:A0 10 11 00 01 Fourth Address A1:A0 11 00 01 10 Linear Burst Address Table (MODE = GND) First Address A1:A0 00 01 10 11 Second Address A1:A0 01 10 11 00 ZZ Mode Electrical Characteristics Parameter IDDZZ tZZS tZZREC tZZI tRZZI Description Sleep mode standby current Device operation to ZZ ZZ recovery time ZZ Active to sleep current ZZ Inactive to exit sleep current Document Number: 001-43822 Rev. *F Test Conditions ZZ > VDD– 0.2 V ZZ > VDD – 0.2 V ZZ < 0.2 V This parameter is sampled This parameter is sampled Min – – 2tCYC – 0 Max 80 2tCYC – 2tCYC – Unit mA ns ns ns ns Page 8 of 31 CY7C1380S CY7C1382S Truth Table Operation [1, 2, 3, 4, 5] Add. Used CE1 CE2 CE3 ZZ ADSP ADSC ADV WRITE OE CLK X X L X L X X X DQ Deselect Cycle, Power Down None H L–H Tri-State Deselect Cycle, Power Down None L L X L L X X X X L–H Tri-State Deselect Cycle, Power Down None L X H L L X X X X L–H Tri-State Deselect Cycle, Power Down None L L X L H L X X X L–H Tri-State Deselect Cycle, Power Down None L X H L H L X X X L–H Tri-State Sleep Mode, Power Down None X X X H X X X X X X Tri-State READ Cycle, Begin Burst External L H L L L X X X L L–H Q READ Cycle, Begin Burst External L H L L L X X X H L–H Tri-State WRITE Cycle, Begin Burst External L H L L H L X L X L–H D READ Cycle, Begin Burst External L H L L H L X H L L–H Q READ Cycle, Begin Burst External L H L L H L X H H L–H Tri-State READ Cycle, Continue Burst Next X X X L H H L H L L–H READ Cycle, Continue Burst Next X X X L H H L H H L–H Tri-State READ Cycle, Continue Burst Next H X X L X H L H L L–H READ Cycle, Continue Burst Next H X X L X H L H H L–H Tri-State WRITE Cycle, Continue Burst Next X X X L H H L L X L–H D WRITE Cycle, Continue Burst Next H X X L X H L L X L–H D READ Cycle, Suspend Burst Current X X X L H H H H L L–H Q READ Cycle, Suspend Burst Current X X X L H H H H H L–H Tri-State READ Cycle, Suspend Burst Current H X X L X H H H L L–H READ Cycle, Suspend Burst Current H X X L X H H H H L–H Tri-State WRITE Cycle, Suspend Burst Current X X X L H H H L X L–H D WRITE Cycle, Suspend Burst Current H X X L X H H L X L–H D Q Q Q Notes 1. X = Don't Care, H = Logic HIGH, L = Logic LOW. 2. WRITE = L when any one or more byte write enable signals, and BWE = L or GW = L. WRITE = H when all byte write enable signals, BWE, GW = H. 3. The DQ pins are controlled by the current cycle and the OE signal. OE is asynchronous and is not sampled with the clock. 4. The SRAM always initiates a read cycle when ADSP is asserted, regardless of the state of GW, BWE, or BWX. Writes may occur only on subsequent clocks after the ADSP or with the assertion of ADSC. As a result, OE must be driven HIGH prior to the start of the write cycle to allow the outputs to tri-state. OE is a don't care for the remainder of the write cycle. 5. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles. During a read cycle all data bits are tri-state when OE is inactive or when the device is deselected, and all data bits behave as output when OE is active (LOW). Document Number: 001-43822 Rev. *F Page 9 of 31 CY7C1380S CY7C1382S Truth Table for Read/Write Function (CY7C1380S) [6, 7] GW BWE BWD BWC BWB BWA Read H H X X X X Read H L H H H H Write Byte A – (DQA and DQPA) Write Byte B – (DQB and DQPB) H L H H H L H L H H L H Write Bytes B, A H L H H L L Write Byte C – (DQC and DQPC) H L H L H H Write Bytes C, A H L H L H L Write Bytes C, B H L H L L H Write Bytes C, B, A H L H L L L Write Byte D – (DQD and DQPD) H L L H H H Write Bytes D, A H L L H H L Write Bytes D, B H L L H L H Write Bytes D, B, A H L L H L L Write Bytes D, C H L L L H H Write Bytes D, C, A H L L L H L Write Bytes D, C, B H L L L L H Write All Bytes H L L L L L Write All Bytes L X X X X X GW BWE BWB BWA Read H H X X Read H L H H Write Byte A – (DQA and DQPA) Write Byte B – (DQB and DQPB) H L H L H L L H Write Bytes B, A H L L L Write All Bytes H L L L Write All Bytes L X X X Truth Table for Read/Write Function (CY7C1382S) [6, 7] Notes 6. X = Don't Care, H = Logic HIGH, L = Logic LOW. 7. Table only lists a partial listing of the byte write combinations. Any combination of BWX is valid. Appropriate write is done based on which byte write is active. Document Number: 001-43822 Rev. *F Page 10 of 31 CY7C1380S CY7C1382S IEEE 1149.1 Serial Boundary Scan (JTAG) The CY7C1380S incorporates a serial boundary scan test access port (TAP).This part is fully compliant with 1149.1. The TAP operates using JEDEC-standard 3.3 V or 2.5 V I/O logic levels. The CY7C1380S contains a TAP controller, instruction register, boundary scan register, bypass register, and ID register. Disabling the JTAG Feature It is possible to operate the SRAM without using the JTAG feature. To disable the TAP controller, TCK must be tied LOW (VSS) to prevent clocking of the device. TDI and TMS are internally pulled up and may be unconnected. They may alternately be connected to VDD through a pull up resistor. TDO must be left unconnected. Upon power up, the device is up in a reset state and does not interfere with the operation of the device. Test Access Port (TAP) Test Clock (TCK) The test clock is used only with the TAP controller. All inputs are captured on the rising edge of TCK. All outputs are driven from the falling edge of TCK. Test Mode Select (TMS) The TMS input is used to give commands to the TAP controller and is sampled on the rising edge of TCK. This pin may be left unconnected if the TAP is not used. The ball is pulled up internally, resulting in a logic HIGH level. Test Data-In (TDI) The TDI ball is used to serially input information into the registers and can be connected to the input of any of the registers. The register between TDI and TDO is chosen by the instruction that is loaded into the TAP instruction register. For information about loading the instruction register, see the TAP Controller State Diagram on page 13. TDI is internally pulled up and can be unconnected if the TAP is unused in an application. TDI is connected to the most significant bit (MSB) of any register. Test Data-Out (TDO) The TDO output ball is used to serially clock data-out from the registers. The output is active depending upon the current state of the TAP state machine (see Identification Codes on page 17). The output changes on the falling edge of TCK. TDO is connected to the least significant bit (LSB) of any register. Performing a TAP Reset A Reset is performed by forcing TMS HIGH (VDD) for five rising edges of TCK. This Reset does not affect the operation of the SRAM and may be performed while the SRAM is operating. At power up, the TAP is reset internally to ensure that TDO comes up in a High Z state. TAP Registers Registers are connected between the TDI and TDO balls and scan data in and out of the SRAM test circuitry. Only one register can be selected at a time through the instruction register. Data is Document Number: 001-43822 Rev. *F serially loaded into the TDI ball on the rising edge of TCK. Data is output on the TDO ball on the falling edge of TCK. Instruction Register Three-bit instructions can be serially loaded into the instruction register. This register is loaded when it is placed between the TDI and TDO balls as shown in the TAP Controller Block Diagram on page 14. Upon power up, the instruction register is loaded with the IDCODE instruction. It is also loaded with the IDCODE instruction if the controller is placed in a reset state as described in the previous section. When the TAP controller is in the Capture-IR state, the two least significant bits are loaded with a binary ‘01’ pattern to allow for fault isolation of the board-level serial test data path. Bypass Register To save time when serially shifting data through registers, it is sometimes advantageous to skip certain chips. The bypass register is a single-bit register that can be placed between the TDI and TDO balls. This shifts data through the SRAM with minimal delay. The bypass register is set LOW (VSS) when the BYPASS instruction is executed. Boundary Scan Register The boundary scan register is connected to all the input and bidirectional balls on the SRAM. The boundary scan register is loaded with the contents of the RAM input and output ring when the TAP controller is in the Capture-DR state and is then placed between the TDI and TDO balls when the controller is moved to the Shift-DR state. The EXTEST, SAMPLE/PRELOAD, and SAMPLE Z instructions can be used to capture the contents of the input and output ring. The Boundary Scan Order on page 18 show the order in which the bits are connected. Each bit corresponds to one of the bumps on the SRAM package. The MSB of the register is connected to TDI, and the LSB is connected to TDO. Identification (ID) Register The ID register is loaded with a vendor-specific 32-bit code during the Capture-DR state when the IDCODE command is loaded in the instruction register. The IDCODE is hardwired into the SRAM and can be shifted out when the TAP controller is in the Shift-DR state. The ID register has a vendor code and other information described in the Identification Register Definitions on page 17. TAP Instruction Set Overview Eight different instructions are possible with the three bit instruction register. All combinations are listed in Identification Codes on page 17. Three of these instructions are listed as RESERVED and must not be used. The other five instructions are described in detail below. Instructions are loaded into the TAP controller during the Shift-IR state when the instruction register is placed between TDI and TDO. During this state, instructions are shifted through the instruction register through the TDI and TDO balls. To execute the instruction after it is shifted in, the TAP controller is moved into the Update-IR state. Page 11 of 31 CY7C1380S CY7C1382S EXTEST The EXTEST instruction drives the preloaded data out through the system output pins. This instruction also connects the boundary scan register for serial access between the TDI and TDO in the Shift-DR controller state. IDCODE The IDCODE instruction loads a vendor-specific 32-bit code into the instruction register. It also places the instruction register between the TDI and TDO balls and shifts the IDCODE out of the device when the TAP controller enters the Shift-DR state. The IDCODE instruction is loaded into the instruction register upon power up or whenever the TAP controller is supplied a test logic reset state. SAMPLE Z The SAMPLE Z instruction connects the boundary scan register between the TDI and TDO balls when the TAP controller is in a Shift-DR state. The SAMPLE Z command places all SRAM outputs into a High Z state. SAMPLE/PRELOAD SAMPLE/PRELOAD is a 1149.1 mandatory instruction. When the SAMPLE/PRELOAD instructions are loaded into the instruction register and the TAP controller is in the Capture-DR state, a snapshot of data on the input and output pins is captured in the boundary scan register. The user must be aware that the TAP controller clock can only operate at a frequency up to 20 MHz, while the SRAM clock operates more than an order of magnitude faster. As there is a large difference in the clock frequencies, it is possible that during the Capture-DR state, an input or output undergoes a transition. The TAP may then try to capture a signal while in transition (metastable state). This does not harm the device, but there is no guarantee as to the value that is captured. Repeatable results may not be possible. To guarantee that the boundary scan register captures the correct value of a signal, the SRAM signal must be stabilized long enough to meet the TAP controller’s capture setup plus hold times (tCS and tCH). The SRAM clock input might not be captured correctly if there is no way in a design to stop (or slow) the clock during a SAMPLE/PRELOAD instruction. If this is an issue, it is Document Number: 001-43822 Rev. *F still possible to capture all other signals and simply ignore the value of the CK and CK# captured in the boundary scan register. After the data is captured, it is possible to shift out the data by putting the TAP into the Shift-DR state. This places the boundary scan register between the TDI and TDO pins. PRELOAD places an initial data pattern at the latched parallel outputs of the boundary scan register cells prior to the selection of another boundary scan test operation. The shifting of data for the SAMPLE and PRELOAD phases can occur concurrently when required; that is, while data captured is shifted out, the preloaded data is shifted in. BYPASS When the BYPASS instruction is loaded in the instruction register and the TAP is placed in a Shift-DR state, the bypass register is placed between the TDI and TDO balls. The advantage of the BYPASS instruction is that it shortens the boundary scan path when multiple devices are connected together on a board. EXTEST Output Bus Tri-State IEEE Standard 1149.1 mandates that the TAP controller be able to put the output bus into a tri-state mode. The boundary scan register has a special bit located at bit #89 (for 165-ball FBGA package). When this scan cell, called the “extest output bus tri-state,” is latched into the preload register during the Update-DR state in the TAP controller, it directly controls the state of the output (Q-bus) pins, when the EXTEST is entered as the current instruction. When HIGH, it enables the output buffers to drive the output bus. When LOW, this bit places the output bus into a High Z condition. This bit can be set by entering the SAMPLE/PRELOAD or EXTEST command, and then shifting the desired bit into that cell, during the Shift-DR state. During Update-DR, the value loaded into that shift-register cell latches into the preload register. When the EXTEST instruction is entered, this bit directly controls the output Q-bus pins. Note that this bit is preset HIGH to enable the output when the device is powered up, and also when the TAP controller is in the Test-Logic-Reset state. Reserved These instructions are not implemented but are reserved for future use. Do not use these instructions. Page 12 of 31 CY7C1380S CY7C1382S TAP Controller State Diagram 1 TEST-LOGIC RESET 0 0 RUN-TEST/ IDLE 1 SELECT DR-SCAN 1 SELECT IR-SCAN 0 1 0 1 CAPTURE-DR CAPTURE-IR 0 0 SHIFT-DR 0 SHIFT-IR 1 1 EXIT1-IR 0 1 0 PAUSE-DR 0 PAUSE-IR 1 0 1 EXIT2-DR 0 EXIT2-IR 1 1 UPDATE-DR UPDATE-IR 1 0 1 EXIT1-DR 0 1 0 1 0 The 0 or 1 next to each state represents the value of TMS at the rising edge of TCK. Document Number: 001-43822 Rev. *F Page 13 of 31 CY7C1380S CY7C1382S TAP Controller Block Diagram 0 Bypass Register 2 1 0 TDI Selection Circuitry Instruction Register 31 30 29 . . . 2 1 0 S election Circuitr y TDO Identification Register x . . . . . 2 1 0 Boundary Scan Register TCK TMS Document Number: 001-43822 Rev. *F TAP CONTROLLER Page 14 of 31 CY7C1380S CY7C1382S TAP Timing Figure 3. TAP Timing Test Clock (TCK) t t TH t TMSS t TMSH t TDIS t TDIH TL t CYC Test Mode Select (TMS) Test Data-In (TDI) t TDOV t TDOX Test Data-Out (TDO) DON’T CARE UNDEFINED TAP AC Switching Characteristics Over the Operating Range Parameter [8, 9] Description Min Max Unit 50 – ns Clock tTCYC TCK Clock Cycle Time tTF TCK Clock Frequency – 20 MHz tTH TCK Clock HIGH time 20 – ns tTL TCK Clock LOW time 20 – ns tTDOV TCK Clock LOW to TDO Valid – 10 ns tTDOX TCK Clock LOW to TDO Invalid 0 – ns tTMSS TMS Setup to TCK Clock Rise 5 – ns tTDIS TDI Setup to TCK Clock Rise 5 – ns tCS Capture Setup to TCK Rise 5 – ns tTMSH TMS Hold after TCK Clock Rise 5 – ns tTDIH TDI Hold after Clock Rise 5 – ns tCH Capture Hold after Clock Rise 5 – ns Output Times Setup Times Hold Times Notes 8. tCS and tCH refer to the setup and hold time requirements of latching data from the boundary scan register. 9. Test conditions are specified using the load in TAP AC test conditions. tR/tF = 1 ns. Document Number: 001-43822 Rev. *F Page 15 of 31 CY7C1380S CY7C1382S 3.3 V TAP AC Test Conditions 2.5 V TAP AC Test Conditions Input pulse levels ...............................................VSS to 3.3 V Input pulse levels ............................................... VSS to 2.5 V Input rise and fall times ...................................................1 ns Input rise and fall time ................................................... 1 ns Input timing reference levels ......................................... 1.5 V Input timing reference levels ....................................... 1.25 V Output reference levels ................................................ 1.5 V Output reference levels .............................................. 1.25 V Test load termination supply voltage ............................ 1.5 V Test load termination supply voltage .......................... 1.25 V 3.3 V TAP AC Output Load Equivalent 2.5 V TAP AC Output Load Equivalent 1.5V 1.25V 50Ω 50Ω TDO TDO Z O= 50 Ω Z O= 50 Ω 20pF 20pF TAP DC Electrical Characteristics and Operating Conditions (0 °C < TA < +70 °C; VDD = 3.3 V ± 0.165 V unless otherwise noted) Parameter [10] Description Min Max Unit IOH = –4.0 mA, VDDQ = 3.3 V Test Conditions 2.4 – V IOH = –1.0 mA, VDDQ = 2.5 V 2.0 – V IOH = –100 µA VDDQ = 3.3 V 2.9 – V VDDQ = 2.5 V 2.1 – V VDDQ = 3.3 V – 0.4 V VDDQ = 2.5 V – 0.4 V VDDQ = 3.3 V – 0.2 V – 0.2 V 2.0 VDD + 0.3 V 1.7 VDD + 0.3 V –0.3 0.8 V VOH1 Output HIGH Voltage VOH2 Output HIGH Voltage VOL1 Output LOW Voltage IOL = 8.0 mA VOL2 Output LOW Voltage IOL = 100 µA VDDQ = 2.5 V VIH Input HIGH Voltage VDDQ = 3.3 V VDDQ = 2.5 V VIL Input LOW Voltage VDDQ = 3.3 V VDDQ = 2.5 V –0.3 0.7 V IX Input Load Current –5 5 µA GND < VIN < VDDQ Note 10. All voltages referenced to VSS (GND). Document Number: 001-43822 Rev. *F Page 16 of 31 CY7C1380S CY7C1382S Identification Register Definitions CY7C1380S (512 K × 36) Instruction Field Revision Number (31:29) 000 Device Depth (28:24) [11] 01011 Description Describes the version number. Reserved for internal use. Device Width (23:18) 165-FBGA 000000 Defines the memory type and architecture. Cypress Device ID (17:12) 100101 Defines the width and density. Cypress JEDEC ID Code (11:1) 00000110100 ID Register Presence Indicator (0) 1 Allows unique identification of SRAM vendor. Indicates the presence of an ID register. Scan Register Sizes Register Name Bit Size (× 36) Instruction 3 Bypass 1 ID 32 Boundary Scan Order (165-ball FBGA package) 89 Identification Codes Instruction Code Description EXTEST 000 Captures I/O ring contents. Places the boundary scan register between TDI and TDO. Forces all SRAM outputs to High Z state. IDCODE 001 Loads the ID register with the vendor ID code and places the register between TDI and TDO. This operation does not affect SRAM operations. SAMPLE Z 010 Captures I/O ring contents. Places the boundary scan register between TDI and TDO. Forces all SRAM output drivers to a High Z state. RESERVED 011 Do Not Use. This instruction is reserved for future use. SAMPLE/PRELOAD 100 Captures I/O ring contents. Places the boundary scan register between TDI and TDO. Does not affect SRAM operation. RESERVED 101 Do Not Use. This instruction is reserved for future use. RESERVED 110 Do Not Use. This instruction is reserved for future use. BYPASS 111 Places the bypass register between TDI and TDO. This operation does not affect SRAM operations. Note 11. Bit #24 is 1 in the register definitions for both 2.5 V and 3.3 V versions of this device. Document Number: 001-43822 Rev. *F Page 17 of 31 CY7C1380S CY7C1382S Boundary Scan Order 165-ball BGA [12, 13] Bit # Ball ID Bit # Ball ID Bit # Ball ID 1 N6 31 D10 61 G1 2 N7 32 C11 62 D2 3 N10 33 A11 63 E2 4 P11 34 B11 64 F2 5 P8 35 A10 65 G2 6 R8 36 B10 66 H1 7 R9 37 A9 67 H3 8 P9 38 B9 68 J1 9 P10 39 C10 69 K1 10 R10 40 A8 70 L1 11 R11 41 B8 71 M1 12 H11 42 A7 72 J2 13 N11 43 B7 73 K2 14 M11 44 B6 74 L2 15 L11 45 A6 75 M2 16 K11 46 B5 76 N1 17 J11 47 A5 77 N2 18 M10 48 A4 78 P1 19 L10 49 B4 79 R1 20 K10 50 B3 80 R2 21 J10 51 A3 81 P3 22 H9 52 A2 82 R3 23 H10 53 B2 83 P2 24 G11 54 C2 84 R4 25 F11 55 B1 85 P4 26 E11 56 A1 86 N5 27 D11 57 C1 87 P6 28 G10 58 D1 88 R6 89 Internal 29 F10 59 E1 30 E10 60 F1 Notes 12. Balls which are NC (No Connect) are pre-set LOW. 13. Bit# 89 is pre-set HIGH. Document Number: 001-43822 Rev. *F Page 18 of 31 CY7C1380S CY7C1382S Maximum Ratings DC Input Voltage ................................ –0.5 V to VDD + 0.5 V Exceeding maximum ratings may shorten the useful life of the device. User guidelines are not tested. Storage Temperature ............................... –65 °C to +150 °C Ambient Temperature with Power Applied ......................................... –55 °C to +125 °C Supply Voltage on VDD Relative to GND .....–0.3 V to +4.6 V Supply Voltage on VDDQ Relative to GND .... –0.3 V to +VDD DC Voltage Applied to Outputs in Tri-State ........................................–0.5 V to VDDQ + 0.5 V Current into Outputs (LOW) ........................................ 20 mA Static Discharge Voltage (per MIL-STD-883, Method 3015) ......................... > 2001 V Latch-up Current ................................................... > 200 mA Operating Range Range Commercial Ambient Temperature 0 °C to +70 °C VDD VDDQ 3.3 V– 5% / 2.5 V – 5% to + 10% VDD Electrical Characteristics Over the Operating Range Parameter [14, 15] Description VDD Power Supply Voltage VDDQ I/O Supply Voltage VOH VOL VIH VIL IX IOZ IDD [16] Test Conditions for 3.3 V I/O for 2.5 V I/O Output HIGH Voltage for 3.3 V I/O, IOH = –4.0 mA for 2.5 V I/O, IOH = –1.0 mA Output LOW Voltage for 3.3 V I/O, IOL = 8.0 mA for 2.5 V I/O, IOL = 1.0 mA Input HIGH Voltage [14] for 3.3 V I/O for 2.5 V I/O Input LOW Voltage [14] for 3.3 V I/O for 2.5 V I/O Input Leakage Current except ZZ GND VI VDDQ and MODE Input Current of MODE Input = VSS Input = VDD Input Current of ZZ Input = VSS Input = VDD Output Leakage Current GND VI VDDQ, Output Disabled VDD Operating Supply Current VDD = Max, IOUT = 0 mA, 6.0-ns cycle, f = fMAX = 1/tCYC 167 MHz ISB1 Automatic CE Power Down Current—TTL Inputs ISB2 Automatic CE Power Down Current-CMOS Inputs ISB3 Automatic CE Power Down Current—CMOS Inputs ISB4 Automatic CE Power Down Current—TTL Inputs VDD = Max, Device Deselected, VIN VIH or VIN VIL, f = fMAX = 1/tCYC VDD = Max, Device Deselected, VIN 0.3 V or VIN > VDDQ – 0.3 V, f=0 VDD = Max, Device Deselected, VIN 0.3 V or VIN > VDDQ – 0.3 V, f = fMAX = 1/tCYC VDD = Max, Device Deselected, VIN VIH or VIN VIL, f = 0 Min 3.135 3.135 2.375 2.4 2.0 – – 2.0 1.7 –0.3 –0.3 –5 Max Unit 3.6 V VDD V 2.625 V – V – V 0.4 V 0.4 V VDD + 0.3 V V VDD + 0.3 V V 0.8 V 0.7 V 5 A –30 – –5 – –5 – – 5 – 30 5 275 A A A A A mA 6.0-ns cycle, 167 MHz – 140 mA 6.0-ns cycle, 167 MHz – 70 mA 6.0-ns cycle, 167 MHz – 125 mA 6.0-ns cycle, 167 MHz – 80 mA Notes 14. Overshoot: VIH(AC) < VDD + 1.5 V (pulse width less than tCYC/2), undershoot: VIL(AC) > –2 V (pulse width less than tCYC/2). 15. TPower up: Assumes a linear ramp from 0 V to VDD(Min) within 200 ms. During this time VIH < VDD and VDDQ < VDD. 16. The operation current is calculated with 50% read cycle and 50% write cycle. Document Number: 001-43822 Rev. *F Page 19 of 31 CY7C1380S CY7C1382S Capacitance Parameter [17] Description CIN Input capacitance CCLK Clock input capacitance CIO Input/Output capacitance 100-pin TQFP 165-ball FBGA Unit Package Package Test Conditions TA = 25 °C, f = 1 MHz, VDD = 3.3 V, VDDQ = 2.5 V 5 9 pF 5 9 pF 5 9 pF Thermal Resistance Parameter [17] Description JA Thermal resistance (junction to ambient) JC Thermal resistance (junction to case) 100-pin TQFP 165-ball FBGA Unit Package Package Test Conditions Test conditions follow standard test methods and procedures for measuring thermal impedance, in accordance with EIA/JESD51. 28.66 20.7 °C/W 4.08 4.0 °C/W AC Test Loads and Waveforms Figure 4. AC Test Loads and Waveforms 3.3 V I/O Test Load R = 317 3.3 V OUTPUT OUTPUT RL = 50 Z0 = 50 GND 5 pF R = 351 VT = 1.5 V INCLUDING JIG AND SCOPE (a) 2.5 V I/O Test Load OUTPUT RL = 50 Z0 = 50 VT = 1.25 V (a) 10% (c) ALL INPUT PULSES VDDQ INCLUDING JIG AND SCOPE 1 ns (b) GND 5 pF 90% 10% 90% 1 ns R = 1667 2.5 V OUTPUT ALL INPUT PULSES VDDQ R = 1538 (b) 10% 90% 10% 90% 1 ns 1 ns (c) Note 17. Tested initially and after any design or process change that may affect these parameters. Document Number: 001-43822 Rev. *F Page 20 of 31 CY7C1380S CY7C1382S Switching Characteristics Over the Operating Range Parameter [18, 19] Description 167 MHz Unit Min Max VDD(typical) to the first access [20] 1 – ms tCYC Clock cycle time 6 – ns tCH Clock HIGH 2.2 – ns tCL Clock LOW 2.2 – ns tPOWER Clock Output Times tCO Data output valid after CLK rise – 3.4 ns tDOH Data output hold after CLK rise 1.3 – ns 1.3 – ns – 3.4 ns – 3.4 ns 0 – ns – 3.4 ns [21, 22, 23] tCLZ Clock to low Z tCHZ Clock to high Z [21, 22, 23] tOEV OE LOW to output valid tOELZ tOEHZ OE LOW to output low Z [21, 22, 23] OE HIGH to output high Z [21, 22, 23] Setup Times tAS Address setup before CLK rise 1.5 – ns tADS ADSC, ADSP setup before CLK rise 1.5 – ns tADVS ADV setup before CLK rise 1.5 – ns tWES GW, BWE, BWX setup before CLK rise 1.5 – ns tDS Data input setup before CLK rise 1.5 – ns tCES Chip enable setup before CLK rise 1.5 – ns tAH Address hold after CLK rise 0.5 – ns tADH ADSP, ADSC hold after CLK rise 0.5 – ns tADVH ADV hold after CLK rise 0.5 – ns tWEH GW, BWE, BWX hold after CLK rise 0.5 – ns tDH Data input hold after CLK rise 0.5 – ns tCEH Chip enable hold after CLK rise 0.5 – ns Hold Times Notes 18. Timing reference level is 1.5 V when VDDQ = 3.3 V and is 1.25 V when VDDQ = 2.5 V. 19. Test conditions shown in (a) of Figure 4 on page 20 unless otherwise noted. 20. This part has a voltage regulator internally; tPOWER is the time that the power is supplied above VDD(minimum) initially before a read or write operation can be initiated. 21. tCHZ, tCLZ, tOELZ, and tOEHZ are specified with AC test conditions shown in part (b) of Figure 4 on page 20. Transition is measured ±200 mV from steady-state voltage. 22. At any voltage and temperature, tOEHZ is less than tOELZ and tCHZ is less than tCLZ to eliminate bus contention between SRAMs when sharing the same data bus. These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed to achieve High Z prior to Low Z under the same system conditions. 23. This parameter is sampled and not 100% tested. Document Number: 001-43822 Rev. *F Page 21 of 31 CY7C1380S CY7C1382S Switching Waveforms Figure 5. Read Cycle Timing [24] t CYC CLK t t ADS CH t CL t ADH ADSP t ADS tADH ADSC t AS tAH A1 ADDRESS A2 t WES A3 Burst continued with new base address tWEH GW, BWE, BWx t CES Deselect cycle tCEH CE t ADVS tADVH ADV ADV suspends burst. OE t OEHZ t CLZ Data Out (Q) High-Z Q(A1) t OEV t CO t OELZ t DOH Q(A2) t CHZ Q(A2 + 1) Q(A2 + 2) Q(A2 + 3) Q(A2) Q(A2 + 1) t CO Burst wraps around to its initial state Single READ BURST READ DON’T CARE UNDEFINED Note 24. On this diagram, when CE is LOW: CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH: CE1 is HIGH or CE2 is LOW or CE3 is HIGH. Document Number: 001-43822 Rev. *F Page 22 of 31 CY7C1380S CY7C1382S Switching Waveforms (continued) Figure 6. Write Cycle Timing [25, 26] t CYC CLK tCH t ADS tCL tADH ADSP t ADS ADSC extends burst tADH t ADS tADH ADSC t AS tAH A1 ADDRESS A2 A3 Byte write signals are ignored for first cycle when ADSP initiates burst t WES tWEH BWE, BW X t WES tWEH GW t CES tCEH CE t t ADVS ADVH ADV ADV suspends burst OE t DS Data In (D) High-Z t OEHZ tDH D(A1) D(A2) D(A2 + 1) D(A2 + 1) D(A2 + 2) D(A2 + 3) D(A3) D(A3 + 1) D(A3 + 2) Data Out (Q) BURST READ Single WRITE BURST WRITE DON’T CARE Extended BURST WRITE UNDEFINED Notes 25. On this diagram, when CE is LOW: CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH: CE1 is HIGH or CE2 is LOW or CE3 is HIGH. 26. Full width write can be initiated by either GW LOW; or by GW HIGH, BWE LOW and BWX LOW. Document Number: 001-43822 Rev. *F Page 23 of 31 CY7C1380S CY7C1382S Switching Waveforms (continued) Figure 7. Read/Write Cycle Timing [27, 28, 29] tCYC CLK tCL tCH t ADS tADH t AS tAH ADSP ADSC ADDRESS A1 A2 A3 A4 A5 A6 t WES tWEH BWE, BW X t CES tCEH CE ADV OE t DS tCO tDH t OELZ Data In (D) High-Z tCLZ Data Out (Q) High-Z Q(A1) tOEHZ D(A5) D(A3) Q(A2) Back-to-Back READs Q(A4) Single WRITE Q(A4+1) BURST READ DON’T CARE Q(A4+2) D(A6) Q(A4+3) Back-to-Back WRITEs UNDEFINED Notes 27. On this diagram, when CE is LOW: CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH: CE1 is HIGH or CE2 is LOW or CE3 is HIGH. 28. The data bus (Q) remains in high Z following a WRITE cycle, unless a new read access is initiated by ADSP or ADSC. 29. GW is HIGH. Document Number: 001-43822 Rev. *F Page 24 of 31 CY7C1380S CY7C1382S Switching Waveforms (continued) Figure 8. ZZ Mode Timing [30, 31] CLK t ZZ I t t ZZ ZZREC ZZI SUPPLY I t RZZI DDZZ ALL INPUTS (except ZZ) Outputs (Q) DESELECT or READ Only High-Z DON’T CARE Notes 30. Device must be deselected when entering ZZ mode. See Truth Table on page 9 for all possible signal conditions to deselect the device. 31. DQs are in high Z when exiting ZZ sleep mode. Document Number: 001-43822 Rev. *F Page 25 of 31 CY7C1380S CY7C1382S Ordering Information The following table contains only the parts that are currently available. If you do not see what you are looking for, contact your local sales representative. For more information, visit the Cypress website at www.cypress.com and refer to the product summary page at http://www.cypress.com/products Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives and distributors. To find the office closest to you, visit us at http://www.cypress.com/go/datasheet/offices. Speed (MHz) 167 Ordering Code CY7C1380S-167AXC Package Diagram Part and Package Type 51-85050 100-pin TQFP (14 × 20 × 1.4 mm) Pb-free Operating Range Commercial CY7C1382S-167AXC CY7C1380S-167BZC 51-85180 165-ball FBGA (13 × 15 × 1.4 mm) Ordering Code Definitions CY 7 C 138X S - 167 XX X C Temperature Range: C = Commercial Pb-free Package Type: XX = A or BZ A = 100-pin TQFP BZ = 165-ball FBGA Frequency Range: 167 MHz Die Revision Part Identifier: 138X = 1380 or 1382 1380 = SCD, 512 K × 36 (18 Mb) 1382 = SCD, 1 Mb × 18 (18 Mb) Technology Code: C = CMOS Marketing Code: 7 = SRAM Company ID: CY = Cypress Document Number: 001-43822 Rev. *F Page 26 of 31 CY7C1380S CY7C1382S Package Diagrams Figure 9. 100-pin TQFP (14 × 20 × 1.4 mm) A100RA Package Outline, 51-85050 51-85050 *D Document Number: 001-43822 Rev. *F Page 27 of 31 CY7C1380S CY7C1382S Package Diagrams (continued) Figure 10. 165-ball FBGA (13 × 15 × 1.4 mm) BB165D/BW165D (0.5 Ball Diameter) Package Outline, 51-85180 51-85180 *F Document Number: 001-43822 Rev. *F Page 28 of 31 CY7C1380S CY7C1382S Acronyms Acronym Document Conventions Description Units of Measure BGA Ball grid array CMOS Complementary Metal Oxide Semiconductor °C degree Celsius FBGA Fine-Pitch Ball Grid Array MHz megahertz I/O Input/Output µA microampere JTAG Joint Test Action Group mA milliampere LSB Least Significant Bit mm millimeter MSB Most Significant Bit ms millisecond OE Output Enable mV millivolt SRAM Static Random Access Memory ns nanosecond TAP Test Access Port ohm TCK Test Clock % percent TMS Test Mode Select pF picofarad TDI Test Data-In V volt TDO Test Data-Out W watt TQFP Thin Quad Flat Pack WE Write Enable Document Number: 001-43822 Rev. *F Symbol Unit of Measure Page 29 of 31 CY7C1380S CY7C1382S Document History Page Document Title: CY7C1380S/CY7C1382S,18-Mbit (512 K × 36/1 M × 18) Pipelined SRAM Document Number: 001-43822 Rev. ECN No. Issue Date Orig. of Change ** 1897927 See ECN VKN / AESA New data sheet. *A 2082246 See ECN JASM Changed status from Preliminary to Final. *B 2904797 04/05/10 VKN Updated Ordering Information (Removed inactive parts). Updated Package Diagrams. *C 2956375 06/19/10 VKN Updated Ordering Information (Updated part numbers). Updated Package Diagrams (Removed spec 51-85115). *D 3218966 04/07/2011 NJY Added Ordering Code Definitions. Updated Package Diagrams. Added Acronyms and Units of Measure. Updated in new template. *E 3571224 04/03/2012 PRIT Updated Functional Description (Removed the Note “For best practices or recommendations, please refer to the Cypress application note AN1064, SRAM System Design Guidelines on www.cypress.com.” and its reference, removed the Note “CE3, CE2 are for 100-pin TQFP and 165-ball FBGA packages only. 119-ball BGA is offered only in 1 chip enable.” and its reference). Updated Selection Guide (Removed 250 MHz, and 200 MHz frequencies related information). Updated Pin Configurations (Removed 119-ball BGA package related information and 165-ball FBGA package related information (only for CY7C1382S). Updated Pin Definitions (Removed the Note “CE3, CE2 are for 100-pin TQFP and 165-ball FBGA packages only. 119-ball BGA is offered only in 1 chip enable.” and its reference). Updated Functional Overview (Removed 250 MHz, and 200 MHz frequencies related information). Updated IEEE 1149.1 Serial Boundary Scan (JTAG) (Removed CY7C1382S related information). Updated Identification Register Definitions (Removed 119-ball BGA package related information, removed CY7C1382S related information). Updated Scan Register Sizes (Removed Bit Size (× 18) column). Updated Boundary Scan Order (Removed 119-ball BGA package related information). Updated Operating Range (Removed Industrial Temperature range). Updated Electrical Characteristics (Removed 250 MHz, and 200 MHz frequencies related information). Updated Capacitance (Removed 119-ball BGA package related information). Updated Thermal Resistance (Removed 119-ball BGA package related information). Updated Switching Characteristics (Removed 250 MHz, and 200 MHz frequencies related information). Updated Package Diagrams (Removed 119-ball BGA package related information). Replaced all instances of IO with I/O across the document. *F 3975671 04/20/2013 PRIT Updated Package Diagrams: spec 51-85180 – Changed revision from *E to *F. Description of Change Completing Sunset Review. Document Number: 001-43822 Rev. *F Page 30 of 31 CY7C1380S CY7C1382S Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at cypress.com/sales. Products Automotive Clocks & Buffers Interface Lighting & Power Control PSoC Solutions cypress.com/go/automotive cypress.com/go/clocks psoc.cypress.com/solutions cypress.com/go/interface PSoC 1 | PSoC 3 | PSoC 5 cypress.com/go/powerpsoc cypress.com/go/plc Memory Optical & Image Sensing cypress.com/go/memory cypress.com/go/image PSoC Touch Sensing cypress.com/go/psoc cypress.com/go/touch USB Controllers Wireless/RF cypress.com/go/USB cypress.com/go/wireless © Cypress Semiconductor Corporation, 2008-2013. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Document Number: 001-43822 Rev. *F Revised April 20, 2013 Page 31 of 31 Intel and Pentium are registered trademarks, and i486 is a trademark of Intel Corporation. All products and company names mentioned in this document may be the trademarks of their respective holders.