1/4 STRUCTURE PRODUCT NAME ： ： 4ch DVD Driver for Car Audio MODEL NAME ： BD8231EFV ◎FEATURES： Silicon Monolithic Integrated Circuit ・3-phase brushless spindle motor driver, 2ch for actuator, 1ch for shared Sled/Loading (total 4ch). ・HTSSOP-B40 package which has large power dissipation is adopted. <Spindle driver> Highly effective and super silent 3-phase PWM drive system are adopted. <Actuator/DC motor driver> A linear BTL method with a low noise & a good playability is adopted. ◎ABSOLUTE MAXIMUM RATING：(Ta=25℃) Parameter Power-supply voltage Power dissipation Operating temperature Storage temperature Symbol PREVCC, SLVM, AVM, VM_S, SPVM, SPRNF Pd Topr Tstg Limits Unit 15 *1 1.6 -40∼85 V W -55∼150 ℃ ℃ ＊1 70mm×70mm, thickness1.6mm, less than 3% share of copper foil when implementing glass epoxy board. Operating at higher than Ta=25℃, 12.8mW shall be reduced per 1 ◎RANGE of RECOMMENDED OPERATION (Please set the power-supply voltage in consideration of a power dissipation.) Parameter Linear driver PreVCC voltage Thread/loading driver power part power-supply voltage Actuator driver power part power-supply voltage Spindle driver Pre driver part voltage Spindle driver power part power-supply voltage Symbol MIN TYP MAX PREVcc SLVM AVM VM_S SPVM,SPRNF 6 6 4 6 6 8 8 8 8 8 10 PREVcc PREcc 10 VM_S This product is not designed for protection against radioactive rays. Status of this document The Japanese version of this document is the formal specification. A customer may use this translation version only for a reference to help reading the formal version. If there are any differences in translation version of this document, formal version takes priority. Be careful to handle because the content of the description of this material might correspond to the labor (technology in the design, manufacturing, and use) in foreign country exchange and Foreign Trade Control Law. REV. A Unit V V V V V 2/4 ◎ELECTRICAL CHARACTERISTICS (Unless otherwise noted Ta=25℃, PREVcc=AVM=SLVM=SPVM=VM_S=8V, Vc=1.65V, RL=8Ω, SPRNF=0.165Ω)) specification value UNIT Condition Parameter Symbol MIN TYP MAX Quiescent current IQ - 27.5 40.0 mA At no load VOFFT VOFT GVFT -50 16.0 0 1.5 17.5 50 2.3 19.0 mV V dB IL=500mA VOFSL VOSL GVSL GVLD -50 13.6 17.1 0 1.5 15.6 19.1 50 2.3 17.6 21.1 mV V dB dB IL=500mA VIN=±0.5V VIN=±0.5V VHB 0.45 0.9 1.35 V IHB=10mA IHIB VHIM VHICM -5 50 1 - 5 6 uA mVpp V Actuator driver part (CH2,3) Output offset voltage Output saturation voltage (vertical harmony) Voltage gain SL/LD driver part (CH4) Output offset voltage Output saturation voltage (vertical harmony) voltage gain (SL) voltage gain (LD) Spindle driver part < hall bias > Voltage of hall bias Spindle driver part < hall amplifier > Input bias current Input level (one side) Common mode input range Spindle driver part < torque instruction I/O > Input dead zone (one side) I/O gain Output ON resistance (vertical harmony) VDZSP gmSP RONSP 0 1.06 - 10 1.37 1 40 1.64 1.8 Output limit current ILIMSP 0.8 (0.132) 1.0 (0.165) 1.2 (0.198) Input impedance PWM frequency RinSP fosc 35 - 47 100 59 - mV A/V Ω A (V) kΩ kHz VFGL - 0.1 0.3 V 10kΩ pull-up (3.3V) VICTL VICTH ICTH 2 - 50 0.8 100 V V uA CTL=3.3V IL=500mA Spindle driver part < FG output > Low voltage CTL Part Low input voltage High input voltage High-level input current ●This product is not designed for protection against radioactive rays. ◎PACKAGE OUTLINE (MAX 13.95 include BURR) S!PWM×2 BD8231EFV LOT NO. HTSSOP-B40 (UNIT : mm) REV. A 3/4 LEVEL SHIFT LEVEL SHIFT LEVEL SHIFT 23 22 VM_S 24 BH 25 SPRNF 26 SPVM 27 SPGND 28 U 29 V 30 W 31 SLVM 32 PGND 33 SL/LDO+ 34 SL/LDO- 35 FCO+ 36 FCO- 37 TKO+ 38 TKO- 39 AVM 40 PREVcc PREGND SUBGND ◎BLOCK DIAGRAM 21 MATRIX CURRENT DETECTOR HALL BIAS 17 18 19 HU+ 16 HU- 15 HV+ 14 HV- 13 HW+ 12 HW- 11 FG 10 TEST 9 GND 8 CTL2 7 CTL1 SPIN 6 HALL AMP/REVERSE PROTECT FG CTL SPCNF 6.7k 1.65V HB 16k 5 LDIN 4 SLOPOUT 3 SLIN 50k 50k 2 FCIN 1 TKIN Vc Vc 10k 100k 100k 16k 47k DUTY CONTROL 20 ◎PIN ASSIGNMENT No. Symbol 1 Vc No. Symbol Control standard voltage input Description 21 VM_S Description Spindle driver Pre part power supply 2 TKIN Tracking input 22 BH 3 FCIN Focus input 23 SPRNF Spindle driver current sense 4 SLIN Sled input 24 SPVM Spindle driver power supply 5 SLOPOUT Sled input OPAMP output terminal Spindle driver current sense bottom hold 25 SPGND 6 LDIN Loading input 26 U Spindle part Power GND 7 SPIN Spindle driver input 27 V Spindle driver V aspect output 8 CTL1 Control terminal 1 28 W Spindle driver W aspect output Spindle driver U aspect output 9 CTL2 Control terminal 2 29 SLVM Sled/Loading driver power supply 10 GND GND 30 PGND Power GND 11 TEST 12 FG Test input terminal (Connect it to GND). 31 SL/LDO+ Sled/Loading positive output FG signal output 32 SL/LDO- 13 SPCNF Sled/Loading negative output Spindle driver filter terminal 33 FCO+ 14 Focus positive output HB Hall bias 34 FCO- Focus negative output 15 HW- Hall signal W-input 35 TKO+ Tracking positive output 16 HW+ Hall signal W+input 36 TKO- 17 HV- Hall signal V-input 37 AVM Tracking negative output Actuator driver power supply 18 HV+ Hall signal V+input 38 PREVcc Linear driver pre part power supply 19 HU- Hall signal U-input 39 PREGND 20 HU+ Hall signal U+input 40 SUBGND PREGND SUBGND ●The FOCUS・TRACKING・SLED・LOADING driver's positive output and negative output are the polarities to the FCIN・TKIN・SLOPOUT・LDIN input respectively. Example) FCO+>FCO - at FCIN>Vc, FCO+<FCO at FCIN<Vc REV. A 4/4 ◎NOTE ON USE 1. Absolute maximum ratings We are careful enough for quality control about this IC. So, there is no problem under normal operation, excluding that it exceeds the absolute maximum ratings. However, this IC might be destroyed when the absolute maximum ratings, such as impressed voltages or the operating temperature range is exceeded, and whether the destruction is short circuit mode or open circuit mode cannot be specified. Please take into consideration the physical countermeasures for safety, such as fusing, if a particular mode that exceeds the absolute maximum rating is assumed. 2. Reverse polarity connection Connecting the power line to the IC in reverse polarity (from that recommended) will damage the part. Please utilize the direction protection device as a diode in the supply line and motor coil line. 3. Power supply line Due to return of regenerative current by reverse electromotive force, using electrolytic and ceramic suppress filter capacitors (0.1µF) close to the IC power input terminals (Vcc and GND) are recommended. Please note the electrolytic capacitor value decreases at lower temperatures and examine to dispensephysical measures for safety. 4. GND line Please keep the GND line [GND(10pin), SPGND(25pin), PGND（30pin）, PREGND（39pin）, SUBGND（40pin）] the lowest potential always, and check the GND voltage when transient voltages are connected to the IC. 5. Thermal design Do not exceed the power dissipation (Pd) of the package specification rating under actual operation, and please design enough temperature margins. This product has exposed the frame to the back side of the package, but please notes that it is assumed to use heat radiation efficiency by the heat radiation for this part. Please take the heat radiation pattern on not only the surface of the substrate but also the back of the substrate widely. 6. Short circuit mode between terminals and wrong mounting Do not mount the IC in the wrong direction and displacement, and be careful about the reverse-connection of the power connector. Moreover, this IC might be destroyed when the dust short the terminals between them or GND. 7. Radiation Strong electromagnetic radiation can cause operation failures. 8. ASO (Area of Safety Operation) Do not exceed the maximum ASO and the absolute maximum ratings of the output driver. 9. TSD (Thermal Shut-Down) The TSD is activated when the junction temperature (Tj) exceeds Tjmax, and the output terminal is switched to OPEN. The guarantee and protection of set are not purpose. Therefore, please do not use this IC after TSD circuit operates, nor use it for assumption that operates the TSD circuit. 10. Capacitor between output and GND If a large capacitor is connected between the output and GND, this IC might be destroyed when Vcc becomes 0V or GND, because the electric charge accumulated in the capacitor flows to the output. Please set said capacitor to smaller than 0.1µF. 11. Inspection by the set circuit board The stress might hang to IC by connecting the capacitor to the terminal with low impedance. Then, please discharge electricity in each and all process. Moreover, when attaching or detaching from jig in the inspection process, please turn off the power before mounting the IC, and turn on after mounting the IC, and vice versa. In addition, please take into consideration the countermeasures for electrostatic damage, such as giving the earth in assembly process, transportation or preservation. 12. Input terminal This IC is a monolithic IC, and has P+ isolation and P substrate for the element separation. Therefore, a parasitic PN junction is firmed in this P-layer and N-layer of each element. For instance, the resistor or the transistor is connected to the terminal as shown in the figure below. When the GND voltage potential is greater than the voltage potential at Terminals A on the resistor, at Terminal B on the transistor, the PN junction operates as a parasitic diode. In addition, the parasitic NPN transistor is formed in said parasitic diode and the N layer of surrounding elements close to said parasitic diode. These parasitic elements are formed in the IC because of the voltage relation. The parasitic element operating causes the interference of circuit operation, then the wrong operation and destruction. Therefore, please be careful so as not to operate the parasitic elements by impressing to input terminals lower voltage than GND (P substrate). Please do not apply the voltage to the input terminal when the power-supply voltage is not impressed. Moreover, please impress each input terminal lower than the power-supply voltage or equal to the specified range in the guaranteed voltage when the power-supply voltage is impressing. Resistor Transistor(NPN) Terminal-A Terminal-B C Terminal-B B E Terminal-A B + P + P P Parasitic element C E + P P-Substrate P P+ P-Substrate Surrounding elements Parasitic element GND Parasitic element Parasitic element GND GND GND Simplified structure of IC 13. Earth wiring pattern If small signal GND and large current GND exist, disperse their pattern. In addition, for voltage change by pattern wiring impedance and large current not to change voltage of small signal GND, each ground terminal of IC must be connected at the one point on the set circuit board. As for GND of external parts, it is similar to the above-mentioned. 14. Reverse-rotation braking In the case of reverse-rotation braking from high-speed rotation, pay good attention to reverse electromotive force. Furthermore, fully check output current and consider the revolutions applied to the reverse-rotation brake. 15. About the capacitor between SPVM and PGND The capacitor between SPVM and PGND absorbs the change in a steep voltage and the current because of the PWM drive, as a result, there is a role to suppress the disorder of the SPVM voltage. However, the effect falls by the influence of the wiring impedance etc, if the capacitor becomes far from IC. Please examine the capacitor between SPVM and PGND to arrange it near IC. REV. A Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of which would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM cannot be held responsible for any damages arising from the use of the products under conditions out of the range of the specifications or due to non-compliance with the NOTES specified in this catalog. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact your nearest sales office. ROHM Customer Support System www.rohm.com Copyright © 2007 ROHM CO.,LTD. THE AMERICAS / EUPOPE / ASIA / JAPAN Contact us : webmaster@ rohm.co. jp 21, Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan TEL : +81-75-311-2121 FAX : +81-75-315-0172 Appendix1-Rev2.0