HC/T User Guide

INTEGRATED CIRCUITS
DATA SHEET
User Guide
Product specification
Supersedes data of January 1993
File under Integrated Circuits, IC06
1997 Nov 25
Philips Semiconductors
Product specification
User Guide
CONTENTS
1
INTRODUCTION
7
INPUT CIRCUITS
2
CONSTRUCTION
3
AC CHARACTERISTICS
3.1
3.2
3.3
3.3.1
74HC inputs
74HCT inputs
Maximum input rise/fall times
Termination of unused inputs
Input current
Input capacitance
Coupling of adjacent inputs
Input voltage and forward diode input current
8
OUTPUT CIRCUITS
3.8
Test conditions
Comparing the speed of HCMOS and LSTTL
Propagation delays and transition times
Supply voltage dependence of propagation
delay
Temperature dependence of propagation delay
Derating system for AC characteristics
Clock pulse requirements
System (parallel) clocking
Clock pulse considerations as functions of
maximum frequency
Minimum AC characteristics
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
4
POWER DISSIPATION
8.1
8.2
8.3
8.4
8.5
8.6
Output drive
Push-pull outputs
Three-state outputs
Open-drain outputs
Increased drive capability of gates
Output capacitance
4.1
4.2
4.3
4.4
4.5
4.6
4.7
9
STATIC NOISE IMMUNITY
10
DYNAMIC NOISE IMMUNITY
11
BUFFERED DEVICES
11.1
11.2
11.3
Definition
Output buffering
Input buffering
12
PERFORMANCE OF OSCILLATORS
4.8
Static
Dynamic
Power dissipation capacitance
Input pulses
Conditions for CPD tests
Additional power dissipation in 74HCT devices
Power dissipation due to slow input rise/fall
times
Comparison with LSTTL power dissipation
13
LATCH-UP FREE
5
SUPPLY VOLTAGE
14
DROP-IN REPLACEMENTS FOR LSTTL
5.1
5.2
5.3
Range
Battery back-up
Power supply regulation and decoupling
15
BUS SYSTEMS
16
PACKAGE PIN CAPACITANCE
6
INPUT/OUTPUT PROTECTION
17
POWER-ON RESET
3.3.2
3.4
3.5
3.6
3.7
NOTE: THE INFORMATION IN THIS USER
GUIDE IS INTENDED AS A DESIGN-AID AND
DOES NOT CONSTITUTE A GUARANTEE.
1997 Nov 25
2
Philips Semiconductors
Product specification
User Guide
1
INTRODUCTION
The 74HC/HCT/HCU family is a comprehensive range of
high-speed CMOS (HCMOS) integrated circuits. Whilst
retaining all the advantages of CMOS technology - wide
operating voltage range, very low power consumption,
high input noise immunity and wide operating temperature
range - these circuits have the high-speed and drive
capabilities of low-power Schottky TTL (LSTTL). An
extensive product range (most TTL functions and some
devices from the successful HE4000B series: analog
multiplexers, long time-constant multivibrators,
phase-locked loops) and the aforementioned performance
open new avenues in system design.
For comparison, the key performance parameters of
HCMOS are shown with those of other technologies in
Table 1. The propagation delay of metal-gate CMOS ruled
out CMOS for many applications until the arrival of our
HE4000B series. Now, our 3 µm gate HCMOS technology
has a speed comparable to LSTTL while retaining the
important CMOS qualities, see Fig.1.
Fig.1
Table 2 compares the operating characteristics of the
74HC and 74HCT IC types with those of LSTTL in more
detail. 74HC and 74HCT devices are ideal for use in new
equipment designs and, as alternatives to TTL devices, in
existing designs. The 74HCT circuits which are direct
replacements for LSTTL circuits also enhance
performance in many respects.
1997 Nov 25
3
Propagation delay as a function of load
capacitance; VCC = 5 V, Tamb = 25 °C.
HCMOS
technology
metal gate
CMOS
standard
TTL
low-power
Schottky
TTL
Schottky
TTL
advanced
low-power
Schottky
TTL
advanced
Schottky
TTL
Fairchild
advanced
Schottky
TTL
74
74LS
74S
74ALS
74AS
74F
0.001
0.1
10
10
2
2
19
19
1.2
1.2
8.5
8.5
5.5
5.5
0.001
0.120
300
300
100
100
500
500
60
60
−
−
190
190
parameters
family
74HC
4000
CD
HE
Philips Semiconductors
Comparison of CMOS and TTL technologies; supply voltage VCC = 5 V; ambient temperature Tamb = 25 °C; load capacitance CL = 15 pF
User Guide
1997 Nov 25
Table 1
Power dissipation, typ. (mW)
Gate
static
dynamic @100 kHz
Counter
static
dynamic @100 kHz
0.0000025
0.075
0.000005
0.125
Propagation delay (ns)
Gate
8
14
94
190
40
80
10
20
9.5
15
3
5
4
7
1.5
2.5
3
4
0.52
9
4
100
19
57
4.8
13
16.5
55
4
12
25
33
100
60
160
125
minimum
30
2
6
15
25
75
40
−
100
typical
minimum
45
25
2
1
6
3
32
25
32
25
70
40
45
−
−
−
125
100
standard outputs
4
0.51
0.8
16
8
20
8
20
20
bus outputs
6
48
24
64
24
48
64
40
20
50
20
50
50
120
60
160
60
120
160
typical
maximum
Delay/power product (pJ)
4
Gate
at 100 kHz
Maximum clock frequency
(MHz)
typical
D-type flip-flop
Counter
Output drive (mA)
1.6
standard outputs
10
bus outputs
15
1
2
4
Product specification
Fan-out (LS-loads)
Philips Semiconductors
Product specification
User Guide
Table 2
Comparison of HCMOS and LSTTL circuits (VCC = 5 V unless stated otherwise; CL = 50 pF)
characteristic
74HCXXX (note 1)
74HCTXXX
74LSXXX
Max. quiescent power dissipation over temp. range at VCCmax
per gate (mW)
per flip-flop (mW)
per 4-stage counter (mW)
per transceiver/buffer (mW)
0.027
0.11
0.44
0.055
6
22
175
60
Max. dynamic power dissipation (CL = 50 pF)
at fi (MHz)
0.1
1
0.1 to 1
10
per gate (mW)
0.25
2.25 22
6
22
per flip-flop (mW)
0.35
2.5
24
22
27
per 4-stage counter (mW)
0.70
3
27
175
200
per buffer/transceiver (mW)
0.30
2.5
24
60
90
10
Operating supply voltage (V)
2 to 6 (HC)
4.5 to 5.5 (HCT)
4.75 to 5.25
Operating temperature range (°C)
−40 to +85
−40 to +125
0 to +70
Max. noise margin (VNMH/VNML V; IOHCMOS = 20 µA; IOLSTTL = 4 mA)
1.4/1.4 (HC)
2.9/0.7 (HCT)
0.7/0.4
Input switching voltage stability over temp. range
±60 mV
±200 mV
standard logic
−8
−0.4
bus logic
−12
−2.6
4
6
8
9
4
8
12
24
6
6
15
6
4
4
15
6
8/8
14
8/11
15
14
22
50
33
Min. output drive current at Tamb max and VCCmin (mA)
source current (VOH = 2.7 V; note 2)
sink current
standard logic (VOL = 0.4 V)
standard logic (VOL = 0.5 V)
bus logic (VOL = 0.4 V)
bus logic (VOL = 0.5 V)
Typ. output transition time (ns) (CL = 15 pF)
standard logic
tTLH
tTHL
bus logic
tTLH
tTHL
Typ. propagation delay (ns) (CL = 15 pF; note 3)
gate tPHL/tPLH
flip-flop tPLH
tPHL
Typ. clock rate of a flip-flop; note 5 (MHz)
1997 Nov 25
5
Philips Semiconductors
Product specification
User Guide
characteristic
74HCXXX (note 1)
74HCTXXX
74LSXXX
Max. input current (µA)
−1
1
−400 to −800
40
3-state output leakage current (± µA)
5
20
Reliability (%/1000 h at 60% confidence level)
0.0005
0.008 (note 4)
IIL
IIH
Notes
1. Data valid for HCMOS between −40 °C and +85 °C.
2. VOH for a few LSTTL bus outputs is specified as 2.4 V.
3. Refer to data sheets for the effect of capacitive loading.
4. RADC report.
5. Measured with a 50% duty factor for HCMOS. For LSTTL, per industry convention, the maximum clock frequency is
specified with no constraints on rise and fall times, pulse width or duty factor.
1997 Nov 25
6
Philips Semiconductors
Product specification
User Guide
2
In a metal-gate CMOS transistor, the source and drain are
formed before the gate is deposited. Moreover, the metal
gate must overlap the source and drain to allow for
alignment tolerances. This is why a metal-gate CMOS
transistor has a higher overlap capacitance than an
HCMOS transistor. Furthermore, the deeper diffusions of
metal-gate CMOS make the junction capacitance larger.
CONSTRUCTION
Our HCMOS family is a result of a continuing development
programme to enhance the proven polysilicon-gate CMOS
process. Figure 2 shows the construction of a basic
inverter from the HE4000B series and its HCMOS
successor.
The polysilicon gate of a HCMOS transistor is deposited
over a thin gate oxide before the source and drain
diffusions are defined. Source and drain regions are
formed using ion implantation, with the polysilicon gates
acting as masks for the implantation. The source and drain
are automatically aligned to the gate, minimizing
gate-to-source and gate-to-drain capacitances. In
addition, the junction capacitances, which are proportional
to the junction area, are reduced because of the shallower
diffusions. Figure 3(c) shows the parasitic capacitances in
a CMOS inverter.
In a silicon-gate MOS transistor, there are three
interconnect layers (diffusion, polysilicon and metal)
instead of the two layers (diffusion and metal) in a
metal-gate MOS transistor. This makes a silicon-gate
MOS transistor more compact. The shorter gate length
means higher drive capability, which in turn increases the
speed at which a silicon-gate MOS transistor can charge
or discharge junction capacitance. The drain current of a
saturated MOS transistor which determines the speed of
the transistor is:
2
– β gate width
I DS = ------ × ----------------------------- × ( gate voltage – threshold voltage )
2 gate length
where β is the current gain factor which is proportional to the thickness of the oxide layer.
The threshold voltage is typically 0.7 V for HCMOS.
Fig.2 Basic inverter (left) in HE4000B CMOS, 6 µm gate, and (right) in HCMOS, 3 µm gate.
Fig.3 (a) Basic CMOS inverter; (b) electrical equivalent; (c) parasitic capacitances in a CMOS inverter.
1997 Nov 25
7
Philips Semiconductors
Product specification
User Guide
3
3.1
(30 − 4) 0.9 = 23 ns for a 5 pF load and (30 - 2) 0.9 = 25 ns
for a 45 pF load.
AC CHARACTERISTICS
Test conditions
Set-up hold and removal times are not affected by output
load, only by supply voltage. To compare a published
HCMOS value with an LSTTL value, multiply the HCMOS
value by 0.9.
The propagation delays and transition times specified in
the HCMOS data sheets are guaranteed when the circuits
are tested according to the conditions stated in the chapter
‘Family Characteristics’, section ‘Family Specifications’.
For some circuits such as counters and flip-flops, the test
conditions are defined further by the a.c. set-up
requirements specified in the data sheet.
Values given in the data sheets are for the whole operating
temperature range (−40 to +125 °C) and the supply
voltages used are 2.0 V, 4.5 V and 6.0 V for 74HC
devices, and 4.5 V for 74HCT devices. This is a much
tougher specification than that commonly used for LSTTL,
where the characteristics are usually only specified at
25 °C and for a 5 V supply. Furthermore, the published
a.c. characteristics of HCMOS are guaranteed for a
capacitive test load of 50 pF, a more realistic load than the
15 pF specified for LSTTL and one that loads the device as
the output switches. The published values for HCMOS are
therefore representative of those measured in actual
systems.
3.2
(a) VCC = 6 V
Comparing the speed of HCMOS and LSTTL
A feature of a HCMOS circuit is its speed - in general,
comparable to that of its LSTTL equivalent. Owing to the
different (more informative) way of specifying data for
HCMOS devices, it will be useful to indicate how to
compare the published data for HCMOS and LSTTL.
For example, in an LSTTL specification, the use of a 15 pF
load instead of a 50 pF one means the maximum
propagation delays and enable times published for the
LSTTL device will be up to 2.5 ns (typ. 1.3 ns) shorter than
those for the HCMOS equivalent. In addition, measuring at
the nominal LSTTL supply voltage of 5 V instead of 4.5 V
(HCMOS) reduces propagation delays and enable times
by a further 10%. So, a 30 ns propagation delay for a
HCMOS device is equivalent to a (30 − 2.5) 0.9 = 25 ns
delay for an LSTTL device measured at 4.5 V and with a
15 pF load.
(b) VCC = 4.5 V
Disable times are measured under different test conditions
too - for HCMOS with a 50 pF, 1 kΩ load, for LSTTL with a
5 pF, 2 kΩ load or for a 45 pF, 667 Ω load. To compare a
HCMOS disable time with that for a LSTTL device with a
5 pF load, subtract 4 ns from the published HCMOS
disable time and multiply by 0.9. To compare a value for a
45 pF load, subtract 2 ns and multiply by 0.9. For example,
a 30 ns HCMOS disable time is equivalent to
1997 Nov 25
(c) VCC = 2 V
Fig.4
8
Typical output transition times as a function of
load capacitance; Tamb = 25 °C; for 74HCT
circuits the data at VCC = 4.5 V only is valid.
Philips Semiconductors
Product specification
User Guide
Operating frequency is also unaffected by output load, but
is affected by supply voltage. To compare a published
HCMOS value with an LSTTL value, multiply the value for
HCMOS at 4.5 V by 1.1.
Table 4
VCC
In general, these guidelines apply both to 74HC and to
74HCT devices. For 74HCT devices however, the
propagation delay is the time for the output to reach 1.4 V
(compared with 50%VCC for 74HC devices), so
HIGH-to-LOW output transition times are slightly more
dependent on load and the LOW-to-HIGH transition times
are slightly less dependent on load than the 74HC
versions.
3.3
Typical output transition times for load
capacitances greater than the standard 50 pF
load, see Fig.4
tTHL or tTLH
standard output
bus-driver output
2.0 V
18.5 ns + 0.32 ns/pF
12.5 ns + 0.22 ns/pF
4.5 V
6.6 ns + 0.12 ns/pF
4.5 ns + 0.077 ns/pF
6.0 V
5.6 ns + 0.10 ns/pF
3.8 ns + 0.065 ns/pF
Note
1. values in pF are the load capacitance minus 50 pF.
Propagation delays and transition times
The symmetrical push-pull output structure of both 74HC
and 74HCT devices gives symmetrical rise/fall times and
provides for a well-balanced system design. Table 3
shows the maximum output transition times for all
standard and bus-driver HCMOS outputs.
(a) VCC = 6 V
The influence of capacitive loading on output transitions is
shown in Fig.4; A good approximation of the output
transition times can be calculated using the data of
Table 4.
Table 3
Maximum output transition times (CL = 50 pF)
(b) VCC = 4.5 V
maximum output transition time
(ns)
VCC
(V)
Tamb =
25 °C
Tamb =
85 °C
Tamb =
125 °C
standard
2
75
95
110
output
4.5(1)
15
19
22
6
13
16
19
bus-driver 2
output
60
75
90
4.5(1)
12
15
18
6
10
13
15
(c) VCC = 2 V
Note
1. 74HC and 74HCT devices; all other data for 74HC
devices only.
− − − expected maximum
 typical value
Fig.5
1997 Nov 25
9
Increase in propagation delay for 74HC
devices as a function of load capacitance;
Tamb = 25 °C.
Philips Semiconductors
Product specification
User Guide
A parameter specified for TTL devices is the output
short-circuit current HIGH (IOS). Originally intended to
reassure the TTL user that the device would withstand
accidental grounding, this parameter has become a
measure of the ability of the circuit to charge the line
capacitance and is used to calculate propagation delays.
In CMOS devices however, there is no need to specify IOS
because the purely capacitive loads allow extrapolation of
the a.c. parameters over the whole loading range. Figure 5
(for 74HC devices) and Fig.6 (for 74HCT devices) show
the increase in propagation delay for loads greater than
50 pF. The additional delay can be calculated from the
output saturation current (short-circuit current). Referring
to the output characteristics (Figs 33 to 36), the
propagation delay is the time taken for the output voltage
to reach 50% of VCC for 74HC devices, or 1.4 V for 74HCT
devices. Since a saturated output transistor acts as a
current source, the additional delay is ∆CV/l, where ∆C is
the load capacitance minus 50 pF, V is the voltage swing
at the output to the switching level of the next circuit, and I
is the average source current of the saturated output.
3.3.1
SUPPLY VOLTAGE DEPENDENCE OF PROPAGATION
DELAY
The dynamic performance of a CMOS device depends on
its drain characteristics. These are related to the switching
thresholds and the gate-to-source voltage VGS which is
equal to the supply voltage VCC. A reduction in VCC
adversely affects the drain characteristics, increasing the
propagation delays.
Over the supply voltage range of 74HCT devices, 4.5 V to
5.5 V, the effects of different propagation delays on
performance are minimal. Over the supply voltage range
of 74HC circuits, 2 to 6 V, the effects on performance are
significant, see Figs 7 and 8.
(a) HIGH-to-LOW
transition
Fig.7
Propagation delay as a function of supply
voltage; Tamb = 25 °C; CL = 50 pF.
Fig.8
Operating frequency as a function of supply
voltage; Tamb = 25 °C; CL = 50 pF.
(b) LOW-to-HIGH
transition
_ _ _ expected maximum
 typical value
Fig.6
Increase in propagation delay for 74HCT
devices as a function of load capacitance; the
different values for tPHL and tPLH are due to the
asymmetrical reference level of 1.3 V at the
outputs; Tamb = 25 °C; VCC = 4.5 V.
1997 Nov 25
10
Philips Semiconductors
Product specification
User Guide
Fig.7 for propagation delay. For operating frequencies
(Fig.8), the reciprocal of the derating coefficients shown
should be used.
TEMPERATURE DEPENDENCE OF PROPAGATION
3.3.2
DELAY
In TTL circuits, β (current gain), internal resistances and
forward-voltage drops are all temperature-dependent. In
HCMOS circuits, essentially only the carrier mobility,
which affects the propagation delay, is temperature
dependent. In general, propagation delay increases by
about 0.3% per °C above 25 °C.
Table 5
Between 25 °C and 125 °C,
tP = tP′ (1.003)Tamb−25
ambient temperature
25 °C
85 °C
125 °C
2V
5 (5x)
6.25 (5y)
7.5 (5z)
1 (x)
1.25
(y = 1.25x)
1.5
(z = 1.5x)
V(1)
6V
0.85 (0.85x) 1.0625 (0.85y)
1.275 (0.85z)
Note
Between −40 °C and +25 °C,
tP =
supply
voltage
4.5
where:
tP′ is the propagation delay at 25 °C,
Tamb is the ambient temperature in °C.
Derating coefficients for the AC characteristics
of HCMOS devices
1. 74HC and 74HCT devices; all other data for 74HC
devices only.
tP′(0,997)25 −Tamb
Figure 9 shows the temperature dependence of a
characteristic such as propagation delay.
All coefficients are derived from the value of the AC
characteristic at VCC = 4.5 V and Tamb = 25 °C denoted in
the table by x.
3.5
Clock pulse requirements
All HCMOS flip-flops and counters contain master-slaves
with level-sensitive clock inputs. When the voltage at the
clock input reaches the voltage threshold of the device,
data in the master (input) section is transferred to the slave
(output) section. The threshold for 74HC devices is
typically 50% of VCC and that for 74HCT devices is 28% of
VCC (1.4 V at VCC = 5 V). The thresholds are virtually
independent of temperature.
Fig.9
3.4
The use of voltage thresholds for clocking is an
improvement over a.c. coupled clock inputs, but it does not
make the devices totally insensitive to clock-edge rates.
When clocking occurs, the internal gates and output
circuits of the device dump current to ground, producing a
noise transient that is equal to the algebraic sum of the
internal and external ground plane noise. When a number
of loaded outputs change simultaneously, the device
ground reference (and therefore the clock reference) can
rise by as much as 500 mV. If the clock input of a
positive-edge triggered device is at or near to its threshold
during a noise transient, multiple triggering can occur. To
prevent this, the rise and fall times of the clock inputs
should be less than the published maximum (500 ns at
VCC = 4.5 V).
Typical influence of temperature on AC
parameters; VCC = 5 V.
Derating system for AC characteristics
Because HCMOS devices are a coherent family,
manufactured under strictly-controlled conditions, it is
possible to have a common set of derating coefficients for
temperature and supply voltage that is valid for all AC
characteristics of all devices. Table 5 shows the derating
coefficients which are derived from the published values of
the AC characteristics at 25 °C for VCC = 4.5 V, denoted by
x in the Table. The coefficients have been established after
extensive high-temperature testing at many supply
voltages. A temperature coefficient of −0.4%/°C was
established after comparing the test results with
worst-case calculations. The voltage derating given in
Table 5 is conservative compared with that shown in
1997 Nov 25
In the HCMOS family, all the J-K flip-flops have a
Schmitt-trigger circuit at the clock input, which eliminates
the need to specify a maximum rise/fall time. The flip-flops
74HC/HCT73, 74, 107, 109 and 112 have special
11
Philips Semiconductors
Product specification
User Guide
Schmitt-trigger circuits for increased tolerance to slow
rise/fall times and ground noise.
For a HCMOS device, the rise/fall time must be limited to
1000, 500 or 400 ns for VCC = 2 V, 4.5 V and 6 V
respectively. If these times are exceeded, noise on the
input or power supply rails may cause the outputs to
oscillate during transitions, causing logic errors and
excessive power dissipation.
The published maximum input clock frequency ratings for
clocked devices are for a 50% duty factor input clock. At
these rated frequencies, the outputs will swing between
VCC and GND, assuming no DC load on the outputs. This
is a very conservative and reliable method of rating the
clock-input-frequency limits for HCMOS devices which are
always at least as good as those for LSTLL even though
they may appear to be inferior. This is because the
maximum operating frequency of a TTL device is
published, not for a 50% duty factor clock, but for a
minimum clock pulse width.
3.6
3.7
The minimum input frequency is measured with a clock
that has a 50% duty factor. For a stand-alone flip-flop, the
following direct relationship exists between the minimum
required width of the clock pulse tw LOW or tw HIGH
(whichever is the longest) and the measured maximum
frequency:
System (parallel) clocking
In synchronously-clocked systems, spreads in the clock
threshold levels of devices can cause logic errors if slow
clock edges are used. For example, if data in one circuit
changes before the clock threshold of the next sequential
circuit is reached, a logic error will occur, see Fig.10.
f max = 1/2t w
If two or more flip-flops are synchronously clocked in
parallel, other timing conditions may cause a lower
maximum frequency than that which can be calculated
from the pulse width measurements. An example is shown
in Fig.11.
Fig.10 In synchronously-clocked systems, changing
the data in one device before the clock
switching threshold of the next has been
reached can cause logic errors. VST1 is the
clock threshold of device 1; VST2 is the clock
threshold of device 2.
Fig.11 Timing conditions for parallel clocking.
To prevent this type of logic error, the maximum rise or fall
time of the clock pulse should be less than twice the
propagation delay of the flip-flop.
1997 Nov 25
Clock pulse considerations as functions of
maximum frequency
12
Philips Semiconductors
Product specification
User Guide
The maximum frequency is now determined by:
1
f max = -----------------------------------------------------------------------------------------------------------------------------------------------------t P max ( CP to Q 1 ) + t P max ( control logic ) + t su ( D 2 to CP )
The measured minimum width (tw) of the clock pulse as
shown in Fig.11 would suggest a higher obtainable
frequency in this example. This parallel clocking scheme is
often encountered in counter circuits (e.g. ′160′ or ′190′
series).
If the internal delays and set-up times exceed the minimum
required duration for the clock pulse, the maximum
frequency will be entirely determined by these internal
delays and set-up times.
Cascading HCMOS counters in a parallel clocking scheme
may also result in lower maximum frequencies than those
given for stand-alone ICs. This is because the frequency
will then be determined by the propagation delay of a count
output, for example the delay of the intermediate logic and
the set-up time between the clock enable and the count
input of the succeeding counter IC.
3.8
Fig.12 Batch-to-batch variation of propagation
delay (tPLH/tPHL).
Table 6 gives the derating coefficients for calculating the
minimum propagation delays of HCMOS devices at
various supply voltages and temperatures.
Minimum AC characteristics
Minimum propagation delays are not specified in the data
sheets. However, an increasing number of HCMOS users
are asking for minimum propagation delay values so that
they can make conclusive data handling calculations.
Since our test programs don’t include lower limits for
propagation delays, it’s impossible for us to guarantee
these values for the entire HCMOS family. However,
propagation delays for the whole HCMOS family have
been constantly monitored by our Quality Department over
the past three years. The very small deviations from the
typical values that were observed between May 1985 and
February 1988 are shown, together with their three sigma
values, in Fig.12. The indicated mean value x is within a
few percent of the published typical values. Users can
derive their own minimum expected values from this figure
and the typical propagation delays published in the data
sheets.
Table 6
Derating coefficient for the expected minimum
propagation delay of HCMOS devices
supply
voltage
ambient temperature
25 °C
−40 °C
2V
2 (2x)
1.67 (2y)
1 (x)
0.83 (y = 0.83 x)
0.8 (0.8x)
0.66 (0.8y)
V(1)
4.5
6V
Notes
1. 74HC and 74HCT devices; all other data for 74HC
devices only.
2. The minimum value is reached at the lowest possible
temperature.
A conservative estimate of minimum propagation delay is
one third of the typical value. For set-up and hold times,
the guard-band which should be applied to obtain
max./min. limits is 5 ns for typical values between the limits
of −5 ns and +5 ns. For typical values beyond −5 ns and
+5 ns, the distribution shown in Fig.12 applies.
All coefficients are derived from the value of the AC
characteristic at VCC = 4.5 V and Tamb = 25 °C denoted in
the table by x.
4
4.1
POWER DISSIPATION
Static
When a HCMOS device is not switching, the p-channel
and n-channel transistors don’t conduct at the same time,
1997 Nov 25
13
Philips Semiconductors
Product specification
User Guide
so leakage current flows between VCC and GND. Because
this leakage current is typically a few nA, HCMOS power
dissipation is extremely low.
additional dissipation is caused by static supply currents
(ICC) whose values are given in the device data sheets.
4.3
Static power dissipation can be calculated for both 74HC
and 74HCT devices from the maximum quiescent current
specified in the data sheets, see Table 7.
Table 7
CPD is specified in the device data sheets, the published
values being calculated from the results of tests described
in this section. The test set-up is shown in Fig.13. The
worst-case operating conditions for CPD are always
chosen and the maximum number of internal and output
circuits are toggled simultaneously, within the constraints
listed in the data sheet. Table 8 gives the pin status for
HCMOS devices during a CPD test. Devices which can be
separated into independent sections are measured per
section, the others are measured per device.
Maximum quiescent current of HCMOS devices
at VCCmax (1) (VI = VCC or GND; IO = 0)
device
quiescent current
complexity
typical
at 25 °C 25 °C
SSI
2 nA
maximum
85 °C
2 µA
20 µA
current
125 °C
40 µA
FF
4 nA
4 µA
40 µA
80 µA
MSI
8 nA
8 µA
80 µA
160 µA
LSI
50 nA
50 µA
500 µA
1000 µA
Power dissipation capacitance
Note
1. 6 V for 74 HC; 5.5 V for 74 HCT.
4.2
Dynamic
When a device is clocked, power is dissipated charging
and discharging on-chip parasitic and load capacitances.
Power is also dissipated at the moment the output
switches when both the p-channel and the n-channel
transistors are partially conducting. However, this transient
energy loss is typically only 10% of that due to parasitic
capacitance.
The total dynamic power dissipation per device (PD) is:
PD = CPD VCC2 fi + ∑(CLVCC2 fo)
Fig.13 Test set-up for determining CPD. The input
pulse is a square wave between VCC and
GND; tr = tf ≤ 6 ns; Tamb = 25 °C. All
switching outputs are loaded with 50 pF
(including test jig capacitance). Unused
inputs are connected to VCC or GND.
(1)
The recommended test frequency for determining CPD is
1 MHz, but this is best increased to 10 MHz when ICC is
low and the device quiescent current influences ICC(AV).
Loading the switched outputs gives a more realistic value
of CPD, because it prevents transient ′through-currents′ in
the output stages. Furthermore, automatic testers often
introduce about 30 pF to 40 pF on each device pin.
where:
CPD
is the power dissipation capacitance per package
fi
is the input frequency
fo
is the output frequency
CL
is the total external load capacitance per output.
The values of CPD in the data sheet have been calculated
using:
The second term of equation (1) implies summing the
product of the effective output load capacitance and
frequency for each output. However, a good
approximation of the total dynamic power dissipation of an
HCMOS system can be obtained by summing the
published CPD values and load capacitance for the
HCMOS devices used and, assuming an average
frequency, using equation (1).
I dyn(device)
C PD = -----------------------V CC f i
where:
Idyn(device) = ICC(AV) − Idyn(load)
and
Idyn(load) = ∑(CLVCCfo)
For one-shot circuits, gates configured as oscillators,
phase-locked loops and devices used in a linear mode,
1997 Nov 25
14
Philips Semiconductors
Product specification
User Guide
Table 8
74HC/
HCT
Pin conditions for CPD tests.
equiv. pin numbers
load
1 2 3 4 5 6 7 8 9 10
(pF)
11 12 13 14 15 16 17 18 19 20 21 22
23 24 25 26 27 28
00
50
P
H
C
D
D
O
G
O
D
D
O
D
D
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
02
50
C
P
L
O
D
D
G
D
D
O
D
D
O
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
03
0
P
H
B
D
D
O
G
O
D
D
O
D
D
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
04
50
P
C
D
O
D
O
G
O
D
O
D
O
D
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
U04
50
P
C
D
O
D
O
G
O
D
O
D
O
D
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
08
50
P
H
C
D
D
O
G
O
D
D
O
D
D
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
10
50
P
H
D
D
D
O
G
O
D
D
D
C
H
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
11
50
P
H
D
D
D
O
G
O
D
D
D
C
H
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
14
50
P
C
D
O
D
O
G
O
D
O
D
O
D
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
20
50
P
H
O
H
H
C
G
O
D
D
O
D
D
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
21
50
P
H
O
H
H
C
G
O
D
D
O
D
D
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
27
50
P
L
D
D
D
O
G
O
D
D
D
C
L
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
30
50
P
H
H
H
H
H
G
C
O
O
H
H
O
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
32
50
P
L
C
D
D
O
G
O
D
D
O
D
D
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
42
100
C
C
O
O
O
O
O
G
O
O
O
L
L
L
P
V
−
−
−
−
−
−
−
−
−
−
−
−
58
50
P
D
D
D
D
O
G
O
L
L
L
H
H
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
73
50
P
H
H
V
D
D
D
O
O
D
G
C
C
H
−
−
−
−
−
−
−
−
−
−
−
−
−
−
74
50
H
Q
P
H
C
C
G
O
O
D
D
D
D
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
75
50
C
Q
D
D
V
D
D
O
O
O
O
G
P
O
O
C
−
−
−
−
−
−
−
−
−
−
−
−
85
50
L
H
P
H
O
C
O
G
L
L
L
L
L
L
L
V
−
−
−
−
−
−
−
−
−
−
−
−
86
50
P
L
C
D
D
O
G
O
D
D
O
D
D
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
93
47
Q
L
L
D
V
D
D
C
C
G
C
C
D
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
107
50
H
C
C
H
O
O
G
D
D
D
D
P
H
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
109
50
H
H
L
P
H
C
C
G
O
O
D
D
D
D
D
V
−
−
−
−
−
−
−
−
−
−
−
−
112
50
P
H
H
H
C
C
O
G
O
D
D
D
D
D
H
V
−
−
−
−
−
−
−
−
−
−
−
−
123
100
L
H
P
C
O
O
O
G
D
D
D
O
C
O
R
V
−
−
−
−
−
−
−
−
−
−
−
−
125
50
L
P
C
D
D
O
G
O
D
D
O
D
D
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
126
50
H
P
C
D
D
O
G
O
D
D
O
D
D
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
132
50
P
H
C
D
D
O
G
O
D
D
O
D
D
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
133
50
P
H
H
H
H
H
H
G
C
H
H
H
H
H
H
V
−
−
−
−
−
−
−
−
−
−
−
−
1997 Nov 25
15
Philips Semiconductors
Product specification
User Guide
74HC/
HCT
equiv. pin numbers
load
1 2 3 4 5 6 7 8 9 10
(pF)
11 12 13 14 15 16 17 18 19 20 21 22
23 24 25 26 27 28
137
100
P
L
L
L
L
H
O
G
O
O
O
O
O
C
C
V
−
−
−
−
−
−
−
−
−
−
−
−
138
100
P
L
L
L
L
H
O
G
O
O
O
O
O
C
C
V
−
−
−
−
−
−
−
−
−
−
−
−
139
100
L
P
L
C
C
O
O
G
O
O
O
O
D
D
D
V
−
−
−
−
−
−
−
−
−
−
−
−
147
50
H
H
H
H
H
O
O
G
C
H
P
H
H
O
O
V
−
−
−
−
−
−
−
−
−
−
−
−
151
100
D
D
L
H
C
C
L
G
L
L
P
D
D
D
D
V
−
−
−
−
−
−
−
−
−
−
−
−
153
50
L
L
D
D
L
H
C
G
O
D
D
D
D
P
D
V
−
−
−
−
−
−
−
−
−
−
−
−
154
100
C
C
O
O
O
O
O
O
O
O
O
G
O
O
O
O
O
L
L
L
L
L
P
V
−
−
−
−
157
50
P
L
H
C
L
L
O
G
O
L
L
O
L
L
L
V
−
−
−
−
−
−
−
−
−
−
−
−
158
50
P
L
H
C
L
L
O
G
O
L
L
O
L
L
L
V
−
−
−
−
−
−
−
−
−
−
−
−
160
55
H
P
D
D
D
D
H
G
H
H
C
C
C
C
C
V
−
−
−
−
−
−
−
−
−
−
−
−
161
50
H
P
D
D
D
D
H
G
H
H
C
C
C
C
C
V
−
−
−
−
−
−
−
−
−
−
−
−
162
55
H
P
D
D
D
D
H
G
H
H
C
C
C
C
C
V
−
−
−
−
−
−
−
−
−
−
−
−
163
50
H
P
D
D
D
D
H
G
H
H
C
C
C
C
C
V
−
−
−
−
−
−
−
−
−
−
−
−
164
200
Q
H
C
C
C
C
G
P
H
C
C
C
C
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
165
50
H
P
D
D
D
D
C
G
C
Q
D
D
D
D
L
V
−
−
−
−
−
−
−
−
−
−
−
−
166
25
Q
D
D
D
D
L
P
G
H
D
D
D
C
D
H
V
−
−
−
−
−
−
−
−
−
−
−
−
173
25
L
L
C
O
O
O
P
G
L
L
D
D
D
Q
L
V
−
−
−
−
−
−
−
−
−
−
−
−
174
25
H
C
Q
D
O
D
O
G
P
O
D
O
D
D
O
V
−
−
−
−
−
−
−
−
−
−
−
−
175
50
H
C
C
Q
D
O
O
G
P
O
O
D
D
O
O
V
−
−
−
−
−
−
−
−
−
−
−
−
181
300
P
H
H
L
L
H
H
L
C
C
C
G
C
B
C
C
C
L
H
L
H
L
H
V
−
−
−
−
182
150
H
L
H
L
H
L
O
G
C
O
C
C
P
H
L
V
−
−
−
−
−
−
−
−
−
−
−
−
190
55
D
C
C
L
L
C
C
G
D
D
H
C
C
P
D
V
−
−
−
−
−
−
−
−
−
−
−
−
191
53
D
C
C
L
L
C
C
G
D
D
H
C
C
P
D
V
−
−
−
−
−
−
−
−
−
−
−
−
192
55
D
C
C
H
P
C
C
G
D
D
H
C
C
P
D
V
−
−
−
−
−
−
−
−
−
−
−
−
193
50
D
C
C
H
P
C
C
G
D
D
H
C
C
P
D
V
−
−
−
−
−
−
−
−
−
−
−
−
194
100
H
Q
D
D
D
D
D
G
H
L
P
C
C
C
C
V
−
−
−
−
−
−
−
−
−
−
−
−
1997 Nov 25
16
Philips Semiconductors
Product specification
User Guide
74HC/
HCT
equiv. pin numbers
load
1 2 3 4 5 6 7 8 9 10
(pF)
11 12 13 14 15 16 17 18 19 20 21 22
23 24 25 26 27 28
195
125
H
H
L
D
D
D
D
G
H
P
C
C
C
C
C
V
−
−
−
−
−
−
−
−
−
−
−
−
221
100
L
H
P
C
O
O
O
G
D
D
D
O
C
O
R
V
−
−
−
−
−
−
−
−
−
−
−
−
237
100
P
L
L
L
L
H
O
G
O
O
O
O
O
C
C
V
−
−
−
−
−
−
−
−
−
−
−
−
238
100
P
L
L
L
L
H
O
G
O
O
O
O
O
C
C
V
−
−
−
−
−
−
−
−
−
−
−
−
240
50
L
P
O
D
O
D
O
D
O
G
D
O
D
O
D
C
D
−
−
V
−
−
−
−
−
−
−
−
241
50
L
P
O
D
O
D
O
D
O
G
D
O
D
O
D
C
D
−
−
V
−
−
−
−
−
−
−
−
242
50
L
O
P
D
D
D
G
O
O
O
C
O
L
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
243
50
L
O
P
D
D
D
G
O
O
O
C
O
L
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
244
50
L
P
O
D
O
D
O
D
O
G
D
O
D
O
D
C
D
V
−
−
−
−
−
−
−
−
−
−
245
50
H
P
D
D
D
D
D
D
D
G
O
O
O
O
O
O
O
V
−
−
−
−
−
−
−
−
−
−
251
100
D
D
L
H
C
C
L
G
L
L
P
D
D
D
D
V
−
−
−
−
−
−
−
−
−
−
−
−
253B
50
L
L
D
D
L
H
C
G
O
D
D
D
D
P
D
V
−
−
−
−
−
−
−
−
−
−
−
−
257
50
P
L
H
C
D
D
O
G
O
D
D
O
D
D
L
V
−
−
−
−
−
−
−
−
−
−
−
−
258
50
P
L
H
C
D
D
O
G
O
D
D
O
D
P
D
V
−
−
−
−
−
−
−
−
−
−
−
−
259
25
L
L
L
C
O
O
O
G
O
O
O
O
Q
P
H
V
−
−
−
−
−
−
−
−
−
−
−
−
273
25
H
C
Q
D
O
O
D
G
P
O
D
D
O
O
D
D
O
V
−
−
−
−
−
−
−
−
−
−
280
100
L
L
O
L
C
C
G
P
L
L
L
L
L
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
283
250
C
H
L
C
P
H
L
G
C
C
H
L
C
L
H
V
−
−
−
−
−
−
−
−
−
−
−
−
297
12
H
H
H
P
Q
L
C
G
D
D
O
O
D
H
H
V
−
−
−
−
−
−
−
−
−
−
−
−
299
250
H
L
L
C
C
C
C
C
H
G
Q
P
C
C
C
C
C
D
L
V
−
−
−
−
−
−
−
−
354
100
D
D
D
D
D
D
L
H
L
G
L
L
L
P
L
L
H
C
C
V
−
−
−
−
−
−
−
−
356
50
D
D
D
D
D
D
D
Q
P
G
L
L
L
L
L
L
H
C
C
V
−
−
−
−
−
−
−
−
365
50
L
P
C
D
O
D
O
G
O
D
O
D
O
D
L
V
−
−
−
−
−
−
−
−
−
−
−
−
366
50
L
P
C
D
O
D
O
G
O
D
O
D
O
D
L
V
−
−
−
−
−
−
−
−
−
−
−
−
367
50
L
P
C
D
O
D
O
G
O
D
O
D
O
D
L
V
−
−
−
−
−
−
−
−
−
−
−
−
368
50
L
P
C
D
O
D
O
G
O
D
O
D
O
D
L
V
−
−
−
−
−
−
−
−
−
−
−
−
373
25
L
C
Q
D
O
O
D
D
O
G
P
O
D
D
O
O
D
D
O
V
−
−
−
−
−
−
−
−
374
25
L
C
Q
D
O
O
D
D
O
G
P
O
D
D
O
O
D
D
O
V
−
−
−
−
−
−
−
−
377
25
L
C
Q
D
O
O
D
D
O
G
P
O
D
D
O
O
D
D
O
V
−
−
−
−
−
−
−
−
390
50
P
L
C
Q
C
C
C
G
O
O
O
D
O
D
D
V
−
−
−
−
−
−
−
−
−
−
−
−
393
47
P
L
C
C
C
C
G
O
O
O
O
D
D
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
1997 Nov 25
17
Philips Semiconductors
Product specification
User Guide
74HC/
HCT
equiv. pin numbers
load
1 2 3 4 5 6 7 8 9 10
(pF)
11 12 13 14 15 16 17 18 19 20 21 22
23 24 25 26 27 28
423
100
L
P
H
C
O
O
O
G
D
D
D
O
C
O
R
V
−
−
−
−
−
−
−
−
−
−
−
−
533
25
L
C
Q
D
O
O
D
D
O
G
P
O
D
D
O
O
D
D
O
V
−
−
−
−
−
−
−
−
534
25
L
C
Q
D
O
O
D
D
O
G
P
O
D
D
O
O
D
D
O
V
−
−
−
−
−
−
−
−
540
50
L
P
D
D
D
D
D
D
D
G
O
O
O
O
O
O
O
C
L
V
−
−
−
−
−
−
−
−
541
50
L
P
D
D
D
D
D
D
D
G
O
O
O
O
O
O
O
C
L
V
−
−
−
−
−
−
−
−
563
25
L
Q
D
D
D
D
D
D
D
G
P
O
O
O
O
O
O
O
C
V
−
−
−
−
−
−
−
−
564
25
L
Q
D
D
D
D
D
D
D
G
P
O
D
O
O
O
O
O
C
V
−
−
−
−
−
−
−
−
573
25
L
P
D
D
D
D
D
D
D
G
H
O
O
O
O
O
O
O
C
V
−
−
−
−
−
−
−
−
574
25
L
Q
D
D
D
D
D
D
D
G
P
O
O
O
O
O
O
O
C
V
−
−
−
−
−
−
−
−
583
200
H
H
H
L
H
C
C
G
C
C
C
L
P
H
H
V
−
−
−
−
−
−
−
−
−
−
−
−
594
225
C
C
C
C
C
C
C
G
C
H
P
P
H
Q
C
V
−
−
−
−
−
−
−
−
−
−
−
−
595
225
C
C
C
C
C
C
C
G
C
H
P
P
P
Q
C
V
−
−
−
−
−
−
−
−
−
−
−
−
597
25
D
D
D
D
D
D
D
G
C
H
P
D
H
Q
D
V
−
−
−
−
−
−
−
−
−
−
−
−
640
25
H
P
D
D
D
D
D
D
D
G
P
O
O
O
O
O
O
C
L
V
−
−
−
−
−
−
−
−
643
50
H
P
D
D
D
D
D
D
D
G
P
O
O
O
O
O
O
C
L
V
−
−
−
−
−
−
−
−
646
50
D
L
H
P
D
D
D
D
D
D
D
G
O
O
O
O
O
O
O
C
L
D
D
V
−
−
−
−
648
50
D
L
H
P
D
D
D
D
D
D
D
G
O
O
O
O
O
O
O
C
L
D
D
V
−
−
−
−
652
50
D
L
H
P
D
D
D
D
D
D
D
G
O
O
O
O
O
O
O
C
L
D
D
V
−
−
−
−
670
200
L
L
L
L
P
C
C
G
C
C
L
H
L
L
L
V
−
−
−
−
−
−
−
−
−
−
−
−
688
50
L
P
L
L
L
L
L
L
L
G
L
L
L
L
L
L
L
L
V
−
−
−
−
−
−
−
−
−
4002
50
C
P
L
L
L
O
G
O
D
D
D
D
O
V
−
−
−
−
−
−
−
4015
100
P
C
O
O
O
D
D
G
D
O
C
C
C
L
Q
V
−
−
−
−
−
4016
0
O
O
O
O
D
D
G
O
O
O
O
D
P
V
−
−
−
−
−
−
−
4017
55
C
C
C
C
C
C
C
G
C
C
C
C
L
P
L
V
−
−
−
−
−
−
4020
29
C
C
C
C
C
C
C
G
C
P
L
C
C
C
C
V
−
−
−
−
−
−
4024
48
P
L
C
C
C
C
G
O
C
O
C
C
O
V
−
−
−
−
−
−
−
4040
48
C
C
C
C
C
C
C
G
C
P
L
C
C
C
C
V
−
−
−
−
−
−
4046A 50
O
C
L
O
H
O
O
G
L
O
O
O
O
P
O
V
−
−
−
−
−
−
4049
50
V
C
P
O
D
O
D
G
D
O
D
O
O
D
O
O
−
−
−
−
−
−
4050
50
V
C
P
O
D
O
D
G
D
O
D
O
O
D
O
O
−
−
−
−
−
−
1997 Nov 25
18
−
Philips Semiconductors
Product specification
User Guide
74HC/
HCT
equiv. pin numbers
load
1 2 3 4 5 6 7 8 9 10
(pF)
11 12 13 14 15 16 17 18 19 20 21 22
4051
0
O
O
O
O
O
L
G
G
L
L
P
O
O
O
O
V
−
−
−
−
−
−
4052
0
O
O
O
O
O
L
G
G
L
P
O
O
O
O
O
V
−
−
−
−
−
−
4053
0
O
O
O
O
O
L
G
G
L
L
P
O
O
O
O
V
−
−
−
−
−
−
4059
17
23 24 25 26 27 28
C
V
−
−
O
V
−
−
−
−
−
−
−
−
−
V
−
−
−
−
−
−
−
−
−
−
O
O
O
L
L
L
V
−
−
O
O
O
O
L
L
L
V
−
−
V
−
−
−
−
−
−
V
−
−
−
−
−
−
D
V
−
−
−
−
−
−
O
G
V
−
−
−
−
−
−
O
O
V
−
−
−
−
−
−
P
D
H
L
L
L
L
L
L
L
H
G
H
H
L
L
L
L
L
L
L
L
4060(1) 106
C
C
C
C
C
C
C
G
C
C
P
L
C
C
C
V
−
−
−
−
−
−
4066
0
O
O
O
O
D
D
G
O
O
O
O
D
P
V
−
−
−
−
−
−
−
4067
0
O
O
O
O
O
O
O
O
O
P
L
G
L
L
L
O
O
O
O
O
O
4075
75
P
L
D
D
D
O
G
L
C
O
D
D
D
V
−
−
−
−
−
−
−
4094
250
H
Q
P
C
C
C
C
G
C
C
C
C
C
C
H
V
−
−
−
−
−
4316
0
O
O
O
O
P
D
L
G
G
O
O
O
O
D
D
V
−
−
−
−
−
−
4351
0
O
O
O
O
O
O
L
H
G
G
H
P
L
O
L
O
O
O
O
V
−
4352
0
O
O
O
O
O
O
L
H
G
G
H
P
L
O
L
O
O
O
O
V
4353
0
O
O
O
O
O
O
L
H
G
G
H
P
L
O
L
O
O
O
O
4510
55
L
C
D
D
L
C
C
G
L
H
C
D
D
C
P
V
−
−
−
4511
200
L
L
H
H
L
L
P
G
C
C
O
O
C
O
C
V
−
−
4514
100
H
P
L
O
O
O
O
O
C
O
C
G
O
O
O
O
O
4515
100
H
P
L
O
O
O
O
O
C
O
C
G
O
O
O
O
4516
50
L
C
D
D
L
C
C
G
L
H
C
D
D
C
P
4518
45
P
H
C
C
C
C
L
G
D
D
O
O
O
O
D
4520
47
P
H
C
C
C
C
L
G
D
D
O
O
O
O
4538
100
G
R
H
P
H
C
C
G
O
O
D
D
L
4543
50
H
L
L
H
L
P
L
G
C
C
C
C
O
5555
−
not applicable
O
−
6323A 7
C
O
O
G
O
O
P
V
−
−
−
−
−
−
−
−
−
−
7014
50
P
C
D
O
D
O
G
O
D
O
D
O
D
V
−
−
−
−
−
−
−
−
−
−
−
−
−
−
7030
7
G
G
C
P
Q
Q
Q
Q
Q
Q
Q
Q
Q
G
L
C
C
C
C
C
C
C
C
C
C
P
H
V
7046A 50
O
C
L
O
H
O
O
G
L
O
O
O
O
P
O
V
−
−
−
−
−
−
7080
50
L
P
L
L
L
L
L
L
L
G
L
L
L
L
L
L
L
C
V
−
−
−
−
−
−
7132
−
not applicable
7245
50
H
P
D
D
D
D
D
D
D
G
O
O
O
O
O
O
C
L
V
−
−
−
−
−
−
7266
50
P
L
C
O
D
D
G
D
D
O
O
D
D
V
−
−
−
−
−
−
−
7403
200
L
C
P
Q
Q
Q
Q
G
H
C
C
C
C
C
P
V
−
−
−
−
−
1997 Nov 25
19
−
Philips Semiconductors
Product specification
User Guide
74HC/
HCT
equiv. pin numbers
load
1 2 3 4 5 6 7 8 9 10
(pF)
11 12 13 14 15 16 17 18 19 20 21 22
23 24 25 26 27 28
7404
225
L
C
P
Q
Q
Q
Q
G
H
C
C
C
C
C
P
V
−
−
−
−
−
−
7540
50
L
P
D
D
D
D
D
D
D
G
O
O
O
O
O
O
O
C
L
V
−
−
−
−
7541
50
L
P
D
D
D
D
D
D
D
G
O
O
O
O
O
O
O
C
L
V
−
−
−
−
7597
25
D
D
D
D
D
D
D
G
C
H
P
D
H
Q
D
V
−
−
−
−
−
−
−
7731
25
C
P
Q
L
D
D
O
G
O
D
D
D
D
D
O
V
−
−
−
−
−
−
9014
50
P
D
D
D
D
D
D
D
D
G
O
O
O
O
O
O
O
O
C
V
−
−
−
−
9015
50
P
D
D
D
D
D
D
D
D
G
O
O
O
O
O
O
O
O
C
V
−
−
−
−
9046
−
not applicable
9114
0
P
D
D
D
D
D
D
D
D
G
O
O
O
O
O
O
O
O
B
V
−
−
−
−
9115
0
P
D
D
D
D
D
D
D
D
G
O
O
O
O
O
O
O
O
C
V
−
−
−
−
40102
5
P
H
L
L
L
L
L
G
H
L
L
L
L
C
H
V
−
−
−
−
−
−
40103
3
P
H
L
L
L
L
L
G
H
L
L
L
L
C
H
V
−
−
−
−
−
−
40104
100
H
Q
D
D
D
D
D
G
H
L
P
C
C
C
C
V
−
−
−
−
−
−
40105
200
L
C
P
Q
Q
Q
Q
G
L
C
C
C
C
C
P
V
−
−
−
−
−
−
Note
1. load word;
0:
0
0
0
0
1:
1
1
1
1
2:
X
X
X
X
3:
X
X
X
X
Key
V
= VCC (+5V)
G
= ground
H
= logic 1 (VCC) - inputs at VCC for HC types;
3.5 V for HCT types
L
= logic 0 (ground)
D
= don’t care - either H or L but not switching
C
= a 50 pF load to ground is allowed
O
= an open pin; 50 pF to ground is allowed
P
= input pulse (see illustration)
Q
= half frequency pulse (see illustration)
R
= 1 kΩ pull-up resistor to an additional 5 V supply
other than the VCC supply
B
= both R and C.
1997 Nov 25
20
Philips Semiconductors
Product specification
User Guide
4.4
Input pulses
1997 Nov 25
21
Philips Semiconductors
Product specification
User Guide
4.5
Display drivers. CPD is not normally required for LED
drivers because LEDs consume so much power as to
make the effect of CPD negligible. Moreover, when
blanked, the drivers are rarely driven at significant speeds.
When it is needed, CPD is measured with outputs enabled
and disabled while toggling between lamp test and blank
(if provided), or between a display of numbers 6 and 7.
Conditions for CPD tests
Gates. All inputs except one are held at either VCC or
GND, depending on which state causes the output to
toggle. The remaining input is toggled at a known
frequency. CPD is specified per-gate.
Decoders. One input is toggled, causing the outputs to
toggle at the same rate (normally one of the address-select
pins is switched while the decoder is enabled). All other
inputs are tied to VCC or GND, whichever enables
operation. CPD is specified per-independent-decoder.
LCD drivers are tested by toggling the phase inputs that
control the segment and backplane waveforms outputs.
If either type of driver (LCD or LED) has latched inputs,
then the latches are set to a flow-through mode.
Multiplexers. One data input is tied HIGH and the other is
tied LOW. The address-select and enable inputs are
configured such that toggling one address input selects
the two data inputs alternately, causing the outputs to
toggle. With three-state multiplexers, CPD is specified per
output function for enabled outputs.
One-shot circuits. In some cases, when the device ICC is
significant, CPD is not specified. When it is specified, CPD
is measured by toggling one trigger input to make the
output a square wave. The timing resistor is tied to a
separate supply (equal to VCC) to eliminate its power
contribution.
Bilateral switches. The switch inputs and outputs are
open-circuit. With the enable input active, one of the select
inputs is toggled, the others are tied HIGH or LOW. CPD is
specified per switch.
4.6
When the inputs of a 74HCT device are driven by a TTL
device at the specified minimum HIGH output level of
VOH = 2.4 V, the input stage p-channel transistor does not
completely switch off and there is an additional quiescent
supply current (∆ICC). This current has been considerably
reduced by proprietary development of 74HCT input
stages, see ′74HCT inputs′.
Three-state buffers and transceivers. CPD is specified
per buffer with the outputs enabled. Measurement is as for
simple gates.
Latches. The device is clocked and data is toggled on
alternate clock pulses. Other preset or clear inputs are
held so that output toggling is enabled. If the device has
common-locking latches, one latch is toggled by the clock.
Three-state latches are measured with their outputs
enabled. CPD is specified per-latch.
The value of ∆ICC specified in the data sheets is per input
and at the worst-case input voltage of VCC − 2.1 V for VCC
between 4.5 and 5.5 V. The value of 2.1 V is the maximum
voltage drop across a TTL output HIGH (minimum VCC and
minimum VOH), see Table 9.
Flip-flops. Measurement is performed as for latches. The
inputs to the device are toggled and any preset or clear
inputs are held inactive.
The additional power dissipation P is:
P = VCC × ∆ICC × duty factor HIGH × unit load coefficient
Shift registers. The register is clocked and the serial data
input is toggled at alternate clock pulses (as described for
latches). Clear and load inputs are held inactive and
parallel data are held at VCC or GND. Three-state devices
are measured with outputs enabled. If the device is for
parallel loading only, it is loaded with 101010..., clocked to
shift the data out and then reloaded.
The unit load coefficient for an input is a factor by which the
value of ∆ICC given in the data sheet has to be multiplied.
A unit load coefficient is published for each 74HCT device.
It is a function of the size of the input p-channel transistor.
Counters. A signal is applied to the clock input but other
clear or load inputs are held inactive. Separate values for
CPD are given for each counter in the device.
Arithmetic circuits. Adders, magnitude comparators,
encoders, parity generators, ALUs and miscellaneous
circuits are exercised to obtain the maximum number of
simultaneously toggling outputs when toggling only one or
two inputs.
1997 Nov 25
Additional power dissipation in 74HCT devices
22
Philips Semiconductors
Product specification
User Guide
Table 9
Worst-case additional quiescent supply current (∆ICC) for 74HCT devices
Tamb (°C)
TEST CONDITIONS
74HCT
+25
∆ICC per input pin for a
unit load coefficient of 1(1)
−40 to +85
−40 to +125
typ.
max.
max.
max.
100
360
450
490
UNIT
µA
VI
VCC
(V)
4.5
to
5.5
OTHER
other inputs at
VCC − 2.1 V VCC or GND
IO = 0
Note
1. The additional quiescent supply current per input is determined by the ∆ICC unit load, which has to be multiplied by
the unit load coefficient as given in the individual data sheets. For dual supply systems the theoretical worst-case
(VI = 2.4 V; VCC = 5.5 V) specification is: ∆ICC = 0.65 mA (typical) and 1.8 mA (maximum) across temperature.
4.7
Power dissipation due to slow input rise/fall
times
4.8
The dynamic power dissipation of a HCMOS device is
frequency-dependent; above 1 MHz, that of an LSTTL
device is too. Below 1 MHz, the dynamic component of
power dissipation of an LSTTL device is negligible
compared to the static component. Figure 15 shows the
average power dissipation of four HCMOS devices and
their LSTTL equivalents. Because all functions in a
multi-functional LSTTL device are biased when power is
applied, for comparison, the dissipation of whole HCMOS
devices besides individual functions are given.
When an output stage switches, there is a brief period
when both output transistors conduct. The resulting
′through-current′ is additional to the normal supply current
and causes power dissipation to increase linearly with the
input rise or fall time.
As long as the input voltage is less than the n-channel
transistor threshold voltage, or is higher than VCC minus
the p-channel transistor threshold voltage, one of the input
transistors is always off and there is no through-current.
In Fig.15 it can be seen that:
When the input voltage equals the n-channel transistor
threshold voltage (typ. 0.7 V), the n-channel transistor
starts to conduct and through-current flows, reaching a
maximum at VI = 0.5 VCC for 74HC devices, and
VI = 28%VCC for 74HCT devices, the maximum current
being determined by the geometry of the input transistors.
The through-current is proportional to VCCn where n is
about 2.2. The supply current for a typical HCMOS input is
shown as a function of input voltage transient in Fig.14.
• for SSI gate types, the HCMOS power dissipation is less
than LSTTL power dissipation below about 1 MHz
• for more complex types such as a 74HC/HCT138 3-to-8
line decoder HCMOS power dissipation is less than
LSTTL power dissipation up to 10 MHz.
In typical microcomputer systems, the operating frequency
or the data/address signal rates will usually vary, whereas
Fig.15 is for continuous operation at a constant frequency.
Average operating frequencies are usually far below the
peak frequencies, particularly in the 100 kHz region where
the power dissipation of HCMOS is several orders of
magnitude less than that of LSTTL.
When Schmitt triggers are used to square pulses with long
rise/fall times, through-current at the Schmitt-trigger inputs
will increase the power dissipation, see Schmitt-trigger
data sheets. In the case of RC oscillators, or oscillators
constructed with Schmitt triggers this contribution to the
power dissipation is frequency-dependent.
1997 Nov 25
Comparison with LSTTL power dissipation
For further information, see chapter ‘Power dissipation’.
23
Philips Semiconductors
Product specification
User Guide
(a) VCC = 2 V
(b) VCC = 3 V
(c) VCC = 4.5 V
(d) VCC = 6 V
Fig.14 Typical DC supply current as a function of input voltage for 74HC circuits; normalized curves for a unit load
coefficient of 1. The ICC for a specific 74HC circuit can be calculated by multiplying the values of ICC shown
by the unit load coefficient for the 74HCT type given in the data sheet.
1997 Nov 25
24
Philips Semiconductors
Product specification
User Guide
(a)
(b)
(c)
(d)
Fig.15 Typical power dissipation as a function of operating frequency for a variety of LSTTL and HCMOS circuits;
(a) quad 2-input NAND gate, (b) dual D-type flip-flop, (c) 3-to-8 line decoder/demultiplexer; inverting,
(d) quad 3-state bus transceiver.
5
5.1
−40 to +125 °C). This allows extended temperature range
LSTTL devices to be replaced by 74HCT devices.
SUPPLY VOLTAGE
Range
The absolute maximum supply or ground current per pin is
±50 mA for devices with standard output drive, and
±70 mA for devices with bus driver outputs. These
currents are only drawn when the outputs of a device are
heavily loaded. The average dynamic current at very high
frequencies can be calculated using CPD.
The supply voltage range of 74HC devices is 2 V to 6 V
(Fig.16). This ensures continued use of HCMOS with
future generations of memory and microcomputer
requiring supply voltages of less than 5 V, simplifies the
regulation requirements of power supplies, facilitates
battery operation and allows lithium battery back-up.
When 74HC devices are used in linear applications, for
example when they are used as RC oscillators, a supply of
at least 3 V is recommended to ensure sufficient margin for
operation in the linear region.
The maximum rated supply voltage of HCMOS devices is
7 V and any voltage above this may destroy the device,
even though the on-chip parasitic diode break-down
voltage is at least 20 V and the threshold voltage of
parasitic thick-field oxide transistors is 15 V.
74HCT devices are pin-compatible with LSTTL circuits
and are intended as power-saving replacements for them.
The 74HCT devices will operate from the traditional 5 V
LSTTL supply, but the voltage range is extended to ±10%
for both LSTTL temperature ranges (−40 to +85 °C and
1997 Nov 25
The VCC and GND potentials must never be reversed as
this can cause excessive currents to flow through the input
protection diodes.
25
Philips Semiconductors
Product specification
User Guide
current to 15 mA for one input (7.5 mA per input for two
inputs, 5 mA per input for three inputs, etc.). External
resistors may also be necessary in the output circuits to
limit the current to 20 mA if the output can be pulled above
VCC or below GND. These current limits are set by the
parasitic VCC/GND diodes present in all outputs, including
three-state outputs.
For further information, see chapter ‘Battery back-up’.
5.3
The wide power supply range of 2 V to 6 V may suggest
that voltage regulation is unnecessary. However, a
changing supply voltage will affect system speed, noise
immunity and power consumption. Noise immunity, and
even the operation of the circuit, can be affected by spikes
on the supply lines, so matched decoupling is always
necessary in dynamic systems.
Fig.16 Supply voltage ranges for LSTTL and
HCMOS circuits. The supply voltage range
for 74HCT circuits retain the LSTTL nominal
supply of 5 V, but the range has been
extended from ±5% to ±10% for both the
standard and the extended temperature
range. 74HC circuits operate with a supply
voltage as low as 2 V.
5.2
Power supply regulation and decoupling
Both 74HC and 74HCT devices have the same power
supply regulation and decoupling requirements. The best
method of minimizing spikes on the supply lines is simple
enough  use a good power supply, provide good ground
bussing and low AC impedances from the VCC and GND
pins of each device. The minimum decoupling capacitance
depends on the voltage spikes that can be tolerated, which
in general should be limited to 400 mV. A local voltage
regulator on a printed circuit board can be decoupled using
an electrolytic capacitor of 10 to 50 µF. Localized
decoupling of devices can be provided by 22 nF per every
two to five packages and a 1 µF tantalum capacitor for
every ten packages. The VCC line of bus driver circuits and
level-sensitive devices can be decoupled from
instantaneous loads by a 22 nF ceramic capacitor
connected as close to the package as possible.
Battery back-up
A battery back-up for a 74HC system is extremely simple.
Figure 17 shows an example. The minimum battery
voltage required is only 2 V plus one diode drop.
For further information, see chapter ‘Power supply
decoupling’.
6
The gate input of a MOS transistor acts as a capacitor
(<1 pF) with very low leakage current (<1 pA). Without
protection, such an input could be electrostatically charged
to a high voltage that would breakdown the dielectric and
permanently damage the device.
Fig.17 An HCMOS system with battery back-up.
The integration process of the HCMOS family allows
polysilicon resistors to be formed at all inputs to slow down
fast input transients caused by electrostatic discharge and
to dissipate some of their energy. These resistors also
ensure that the input impedance of an HCMOS device is
typically 100 Ω under all biasing conditions, even when
In the example, HIGH-to-LOW level shifters (74HC4049 or
74HC4050) prevent positive input currents into the system
due to input signals greater than one diode drop above
VCC. If the circuit is such that input voltages can exceed
VCC, external resistors should be included to limit the input
1997 Nov 25
INPUT/OUTPUT PROTECTION
26
Philips Semiconductors
Product specification
User Guide
VCC is short-circuited to GND  an improvement over
direct input diode clamps during power-up.
Fig.19 Input protection of 74HC4049 and 74HC4050.
Fig.18 Standard input protection of 74HC/HCT/HCU
inputs against electrostatic discharge.
Although all inputs and outputs are protected against
electrostatic discharge, the standard CMOS handling
precautions should be observed (see chapter ‘Handling
precautions’).
The standard input protection comprises a series
polysilicon resistor and two stages of diode clamping
(Fig.18). The typical forward voltage of the diodes is 0.9 V
at 2 mA and the reverse breakdown voltage is 20 V. In
some applications such as oscillators, the diodes conduct
during normal operation, in which case the input current
should be limited. The maximum positive input current +IIK
per input is 20 mA. For devices with a standard output, the
total positive input current is 50 mA; for devices with a
bus-driver output, the total input current is 70 mA. The
maximum negative input current −IIK per pin is:
(a) Test circuit.
14 mA for one input
9 mA for two inputs
6 mA for three inputs
5 mA for four inputs
4 mA for five inputs
3 mA for six to eight inputs.
mode
device under test
+
−
1
input
GND
2
GND
input
3
input
VCC
High-to-low level shifters 74HC4049 and 74HC4050 have
a single-sided input protection network (Fig.19) which
protects against electrostatic input voltages. The diode D1
is the parasitic drain-to-GND diode of the thick field oxide
protection device.
4
VCC
input
5
output
GND
6
GND
output
7
output
VCC
All input pins can withstand discharge voltages up to
2.5 kV (typ.) when tested according to MIL-STD-883B,
method 3015, see Fig.20. The output configurations of
standard, bus driver, three-state, open drain and I/O ports
can withstand >3.5 kV (typ.) because of the large diodes
formed by the drain surfaces of the output transistors.
8
VCC
output
9
input
output
10
output
input
11
VCC
GND
12
GND
VCC
Note
Figure 21 shows the voltage pulse for the discharge test.
The rise time tr prescribed by MIL-STD-883B is ≤15 ns, but
in practice it is helpful to adjust the test set-up to give a rise
time of 13 ± 2 ns to avoid correlation problems.
1. all other pins should be left open circuit
(b) Test modes
Fig.20 Electrostatic discharge test.
1997 Nov 25
27
Philips Semiconductors
Product specification
User Guide
the switching threshold are the spreads of β and VT of P1
and N1 between devices.
Fig.21 Test voltage for electrostatic discharge test.
7
7.1
INPUT CIRCUITS
Fig.23 74HC input switching level as a function of
supply voltage.
74HC inputs
The 74HC input circuit (Fig.22) includes the resistor/diode
network for electrostatic discharge protection and clamps
input voltages greater than VCC or less than GND. The
circuit is intended for AC working and cannot handle heavy
DC currents for long periods; the maximum input diode
current is 20 mA.
There is no current path from VCC to GND when the input
is lower than VTN, or higher than VCC−VTP. However, when
the input voltage is in the linear region, a static current path
from VCC or GND flows in the input stage (Fig.14). This
current is negligible under normal operating conditions
when the input rise time tr ≤ 15 ns, but the power
dissipation should be taken into account for devices
operating in the linear region. Owing to the voltage gain of
the input stage, there is no static flow-through current in
the second and subsequent stages. Small currents do flow
in these stages during operation when both n-channel and
p-channel transistors conduct for brief periods and their
effect is included in the CPD value in the data sheets.
7.2
Fig.22 74HC input circuit.
The 74HCT input stage is similar to that of a 74HC device.
It has the same characteristics for LSTTL levels as a 74HC
input has for CMOS levels, so there is no trade-off in speed
or power dissipation. The switching threshold is lower,
1.4 V at VCC = 5 V. In addition, the 74HCT input circuit,
shown in Fig.24, has an enlarged n-channel transistor (N1)
and a level-shift diode (D3) has been added. The natural
drain voltage of the p-channel transistor (P1) is
approximately VCC − 0.6 V, but when the input voltage is
LOW, an auxiliary pull-up transistor (P2) raises this to VCC,
cutting off p-channel transistor P3 completely. The input
stage is well matched to the load presented by the second
stage so that symmetrical propagation delays are
obtained.
The 74HC input circuit has no active input current; the only
current flowing is through the reversed-biased diodes D1
and D2, typically a few nA reaching a maximum when
VI = VCC or GND.
The MOS transistors P1 (p-channel) and N1 (n-channel)
have the same conductance when switched on, giving a
typical switching threshold of 50% VCC, see Fig.23. This
threshold is almost independent of temperature, a ±60 mV
variation of the switching point from −40 to +125 °C being
typical. The temperature dependence of VIL is −0.6 mV/°C,
that of VIH is +0.6 mV/°C. The only other factors that affect
1997 Nov 25
74HCT inputs
28
Philips Semiconductors
Product specification
User Guide
maximum through-currents ∆ICC per input are given in the
data sheets.
In a system where 74HCT devices are only driven by
LSTTL devices, VOH min can be 2.7 V except for some bus
drivers. With VOH = 2.7 V, ∆ICC is half the published value.
7.3
Maximum input rise/fall times
All digital circuits can oscillate or trigger prematurely when
input rise and fall times are very long. When the input
signal to a device is at or near the switching threshold,
noise on the line will be amplified and can cause oscillation
which, if the frequency is low enough, can cause
subsequent stages to switch and give erroneous results.
For this reason, Schmitt-triggers are recommended if
rise/fall times are likely to exceed 500 ns at VCC = 4.5 V.
Fig.24 74HCT input circuit.
(a)
Fig.25 74HCT input switching level as a function of
supply voltage.
(b)
Figure 25 shows the switching level as a function of supply
voltage.
A TTL HIGH level can be as low as 2.4 V. An input of this
order to a HCMOS device would not cut off P1 completely,
and additional supply current would flow through the input
stage. A level-shift diode D3 and the influence of the
back-gate (substrate) connection to P1 minimizes power
dissipation caused by this through-current and gives an
input switching level compatible with LSTTL. Figure 26
shows the input stage through-current with and without the
diode circuit. The peak in the curve occurs at the input
switching threshold.
− − − with no level-shift diode
 with standard input structure
Fig.26 Additional quiescent supply current ∆ICC (typ.)
per input pin of a 74HCT device as a function of
supply voltage (unit load coefficient is 1);
(a) VCC = 4.5 V, (b) VCC = 5.5 V.
The input stage through-current is virtually zero for a
typical TTL HIGH level input of 3.5 V. Thus, this unique
74HCT input structure gives true CMOS low
power-consumption when driven by TTL. Typical and
1997 Nov 25
29
Philips Semiconductors
Product specification
User Guide
The flip-flops 74HC/HCT73, 74, 107, 109 and 112
incorporate Schmitt-trigger input circuits and the
74HC/HCT14 and 132 are dedicated Schmitt triggers with
specified input levels.
For further information, see chapter ‘Schmitt trigger
applications’.
7.4
Termination of unused inputs
To prevent any possibility of linear operation of the input
circuitry of an LSTTL device, it is good practice to
terminate all unused LSTTL inputs to VCC via a 1.2 kΩ
resistor. Inputs should not be connected directly to GND or
VCC, and they should not be left floating.
Fig.27 Typical HCMOS input leakage current II as
a function of ambient temperature Tamb.
Unlike LSTTL inputs, the impedance of 74HC and 74HCT
inputs is very high and unused inputs must be terminated
to prevent the input circuitry floating into the linear mode of
operation which would increase the power dissipation and
could cause oscillation. Unused 74HC and 74HCT inputs
should be connected to VCC or GND, either directly (a
distinct advantage over LSTTL), or via resistors of
between 1 kΩ and 1 MΩ. Since the resistors used to
terminate the inputs of LSTTL devices are usually between
220 Ω and 1.2 kΩ, it is often possible to directly replace
LSTTL circuits with their 74HCT counterparts.
7.6
Since CMOS inputs present essentially no load, fan-out is
limited only by the input capacitance. This is specified as
3.5 pF (typ.) and comprises package, bonding
pad/interconnecting track, input protection diode and
transistor gate capacitances. Figs 28 and 29 show the
typical input capacitances for powered 74HC and 74HCT
devices. The initial decrease in capacitance as VI rises
from zero or falls from 5 V is due to increased reverse bias
on the protection diodes. The peak is caused by internal
Miller feedback capacitance when the inverter is in its
linear mode. A conservative value for the maximum input
capacitance is 10 pF (20 pF for I/O pins owing to the
output drain capacitance). Input capacitance is measured
with all other inputs tied to ground.
Some of the bidirectional (transceiver) logic devices in the
HCMOS family have common I/O pins. These pins cannot
be connected directly to VCC or GND. Instead, when
defined as inputs, they should be connected via a 10 kΩ
resistor to VCC or GND.
7.5
Input capacitance
Input current
Figure 27 shows the typical input leakage current of a
HCMOS device as a function of ambient temperature for a
VCC of 6 V. Over the total operating temperature range, the
input leakage current is well below the rating specified in
the JEDEC standard (100 nA between −55 °C and +25 °C
and 1µA at +85 °C and +125 °C. The reason for this
difference between the measured performance and the
rating is the high-speed testing limitations associated with
test system resolution and the measurement of settling
time. A secondary reason is that the rating is end-of-line,
allowing some leakage current shift due to the ingress of
moisture or foreign material.
Fig.28 Typical input capacitance CI of a 74HC
device as a function of input voltage;
VCC = 5 V; Tamb = 25 °C.
1997 Nov 25
30
Philips Semiconductors
Product specification
User Guide
Fig.29 Typical input capacitance CI of a 74HCT
device as a function of input voltage;
VCC = 5 V; Tamb = 25 °C.
Fig.30 Cross-section of the input protection of an HCMOS device showing the parasitic pnp transistor between
adjacent inputs.
Fig.31 12 V-to-5 V logic-level conversion at HCMOS inputs using 100 kΩ series resistors.
1997 Nov 25
31
Philips Semiconductors
Product specification
User Guide
7.7
8
Coupling of adjacent inputs
Parasitic bipolar pnp transistors can be present between
adjacent inputs, e.g. between an input protection diode to
VCC and the same diode at the adjacent input, as shown in
Fig.30. If the recommended operating input voltage is
exceeded, perhaps by ringing of more than 0.7 V, current
into the terminal (I1) can cause a current I2 in the parasitic
transistor and in the adjacent input (Fig.31). Because I2 in
the adjacent input has to be drained by the source driving
that input, the source resistance (R) must be low. If R is not
low enough, the parasitic current can lift the source voltage
and cause unwanted switching.
8.1
Output drive
There are three different output configurations in the
HCMOS family:
• push-pull
• three-state
• open-drain n-channel transistor.
Each is available with a standard output or a bus driver
output, the latter having 50% more drive capability. All
74HC and 74HCT outputs are buffered for consistent
current drives and AC characteristics throughout the
HCMOS family. Well-matched output n-channel and
p-channel transistors give symmetrical output rise and fall
times.
The ratio of the parasitic adjacent input current (I2) to the
forced input current (I1) denoted α:
I
α = ---2I1
When comparing the output drive capabilities of HCMOS
with those of LSTTL, note that LSTTL capability is usually
expressed in unit loads (ULs) where the load is specified
to be an input of the same family. This guarantees that a
system will operate correctly with worst-case LOW and
HIGH input signals and that noise immunity margins will be
preserved. HCMOS capability is expressed as the source
or sink current at a specified output voltage. Since HCMOS
requires virtually no input current, the unit load concept is
not applicable.
α has been reduced to less than 0.05 (typically 0.001) in
the HCMOS family by the use of deep guard rings and
optimum bonding pad spacing.
A low α permits proper logic operation in the presence of
transients and also allows HIGH-to-LOW voltage
translation simply by adding series input resistors. For
example, in Fig.31, 12 V system logic is converted to 5 V
system logic by adding a 100 kΩ resistor in each input.
Since the logic signals are delayed by 1-2 µs, this
arrangement is suitable for rather slow 12 V control logic
such as that in automotive applications. When the input
diodes are used as clamps for logic level translation, the
total input current should be limited to 20 mA.
7.8
OUTPUT CIRCUITS
With a specified output drive of 4 mA (at VOLmax = 0.4 V),
the HCMOS capability exceeds 4000 ULs, and with a
20 µA (at VOL = 0.1) specification the HCMOS capability is
20 ULs. A standard HCMOS output can drive ten LSTTL
loads and maintain VOL ≤ 0.4 V over the full temperature
range. A bus driver output can drive 15 LSTTL loads under
the same conditions. Table 10 shows the output drive
capabilities of some HCMOS devices expressed in LSTTL
unit loads. The output current may be increased for higher
output voltages. For example, extrapolating the 6 mA bus
driver capability at VOL = 0.33 V and Tamb = 85 °C to a VOL
of 0.5 V gives an output drive capability of 9 mA.
Input voltage and forward diode input current
As a general rule, CMOS logic devices with input clamp
diodes (Fig.18) should be operated between the power
supply rails. Neglecting the input series polysilicon resistor
shown in Fig.18, this means: −0.5 V ≤ VI ≤ VCC + 0.5 V.
This rule is JEDEC Std. No. 7A and is intended to prevent
users damaging devices similar to HCMOS that do not
have the polysilicon resistor. HCMOS devices however
meet the tougher rating: −1.5 V ≤ VI ≤ VCC + 1.5 V.
Furthermore, virtually all HCMOS devices can operate
reliably up to the rating without logic errors.
Output current derating as a function of temperature is
shown in Fig.32 and is valid for all types of output. Output
source and sink drives at VCC = 2 V, 4.5 V and 6 V are
given in Figs 33 to 36 which show the output current as a
function of output voltage; these graphs indicate the typical
output currents and the expected minimum output
currents. They can serve as a design aid when calculating
transmission line effects or when charging highly
capacitive loads.
The maximum permissible continuous current forced into
an input or output of a HCMOS device is ±20 mA (JEDEC
rating).
The expected minimum curves are not guaranteed; they
are tested only at the values given in the data sheets.
1997 Nov 25
32
Philips Semiconductors
Product specification
User Guide
Fig.32 Derating curve for output drive currents IOL
and IOH.
Table 10 Comparison of the output drive capabilities of LSTTL and HCMOS (VOL ≤ 0.4 V)
LS device
output
drive capacity
HCMOS equiv.
type
output
drive capacity
74LS00
4 mA
10 UL
74HC00
standard
4 mA
10 UL
74LS138
4 mA
10 UL
75HC138
standard
4 mA
10 UL
74LS245
12 mA
30 UL
74HC245
bus
6 mA
15 UL
74LS374
12 mA
30 UL
74HC374
bus
6 mA
15 UL
Note
1. UL = unit load.
1997 Nov 25
33
Philips Semiconductors
Product specification
User Guide
(a) VCC = 2 V
(a) VCC = 2 V
(b) VCC = 4.5 V
(b) VCC = 4.5 V
(c) VCC = 6 V
(c) VCC = 6 V
Fig.33 Standard output n-channel sink current.
1997 Nov 25
Fig.34 Standard output p-channel source current.
34
Philips Semiconductors
Product specification
User Guide
(a) VCC = 2 V
(a) VCC = 2 V
(b) VCC = 4.5 V
(b) VCC = 4.5 V
(c) VCC = 6 V
(c) VCC = 6 V
Fig.35 Bus-driver output n-channel sink current.
1997 Nov 25
Fig.36 Bus-driver output p-channel source current.
35
Philips Semiconductors
Product specification
User Guide
8.2
Non-standard inputs or outputs may not be in-circuit
tested. Examples of non-standard inputs/outputs are:
Push-pull outputs
A typical push-pull output stage is shown in Fig.37. The
bipolar parasitic transistor-drain diodes (D1 and D2) limit
the output voltage VO of all HCMOS devices in the case of
externally-forced voltages such that
−0.5 V ≤ VO ≤ VCC + 0.5 V. For voltages outside this
range, the diodes and parasitic bipolar elements start to
conduct. Although the diode current rating is 20 mA DC,
line ringing and power supply spikes in normal high-speed
systems cause current-peaks that exceed this rating.
Careful chip-layout and adequate aluminium traces ensure
that the current peaks produced will not damage the
diodes or degrade the internal circuitry.
• timing pins (Rx, Cx) of monostables ‘123’, ‘221’, ‘423’
and ‘4538’
• the Y and Z pins of all compensated analog switches
(‘4051’ series, ‘4351’ series, ‘4066’ and ‘4077’)
• pins for external timing components of PLLs ‘4046A’ and
‘7046A’
• the RTC and CTC pins of the ‘4060’.
The only exception to this rule is the non-standard output
of the ‘4511’.
8.3
Three-state outputs
In the typical three-state output circuit shown in Fig.38,
when EO is HIGH the output is enabled and transistors P4
and N4 act as a transmission gate connecting the gates of
the output transistors. A LOW at EO puts the output in the
high-impedance OFF-state and transistors P3 and N3 act
as pull-up and pull-down transistors respectively. The logic
symbol for a three-state output and its function table is
shown in Fig.39.
Fig.37 Basic CMOS output stage.
The maximum rated DC current for a standard output is
25 mA and that for a bus-driver output is 35 mA. These
ratings are dictated by the current capability of on-chip
metal traces and long-term aluminium migration, but it is
expected that output currents during switching transients
will, at times, exceed the maximum ratings.
A shorted output will also cause the maximum DC current
rating to be exceeded. However, one output may be
shorted for up to 5 s without causing any direct damage to
the IC.
Fig.38 Typical three-state output circuit.
The life of the IC will not be shortened if not more than one
input or output at a time is forced to GND or VCC during
in-circuit logic testing (“back drive”) as long as the following
rules are obeyed:
• maximum duration
:
1 ms
• maximum duty factor : 10 %
• maximum VCC
1997 Nov 25
:
6V
36
Philips Semiconductors
Product specification
User Guide
Diodes D1 and D2 are parasitic diodes associated with
output transistors P5 and N5 respectively. Diode D1
clamps the output at one VBE above VCC, of importance in
large systems where sections of the system may be
powered-down (VCC = 0 V), in which case the output diode
current has to be limited to 20 mA.
(a) logic symbol
inputs
All I/O ports and transceivers have a three-state output as
shown in Fig.38. The I/O pin is defined as an input when
the output is disabled, but this pin should be regarded as a
real input and should not be left floating, because the input
to an I/O port can cause VCC current. If necessary,
terminate the input with a 10 kΩ resistor, see ‘Termination
of unused inputs’.
outputs
I
EO
O
X
L
Z
L
H
L
H
H
H
Notes
8.4
1. H = HIGH voltage level
In TTL families, several functions are offered with
open-collector outputs to enhance logic functions by using
OR- tied logic. The advantage of OR-tied logic is the logic
elements saved and hence the lower power dissipation.
However, this is countered by power loss and reliance on
RC time propagation delays. These disadvantages are not
encountered in CMOS and similar applications can be
made using devices with 3-state outputs, or simply with the
power-saving logic devices. However, the 74HC/HCT03
(quad 2-input NAND gate) has an open-drain n-channel
output, see Fig.40. The parasitic diode D1 is not present
(there being no p-channel transistor); this allows the output
voltage to be pulled above VCC to VOmax making both
HIGH-to-LOW and LOW-to-HIGH level-shifting possible.
For digital operation, a pull-up resistor is necessary to
establish a logic HIGH level.
2. L = LOW voltage level
3. X = don’t care
4. Z = high impedance OFF-state
(b) function table
Fig.39 Three-state output logic symbol and functions.
Three-state outputs are designed to be tied together but
are not intended to be active simultaneously. To minimize
noise and to protect outputs from excessive power
dissipation, only one three-state output should be active at
any time. In general, this requires that the output enable
signals should not overlap. When decoders are used to
enable three-state outputs, the decoder should be
disabled while the address is being changed. This avoids
overlapping output-enable signals caused by decoding
spikes to which all decoder outputs are prone during
address-changing.
The open drain output is protected against electrostatic
discharge.
When designing with three-state outputs, note that disable
propagation delays are measured for an RC load when the
output voltage has changed by 10% of the voltage swing.
This 10% level is adequate to ensure that a device output
has turned off. Although this method provides a standard
reference for measuring disable times, it implies that the
output is already off for 10% of the RC time. Because all
disable times are measured with a load of 1 kΩ and 50 pF,
subtract the 10% RC time (5 ns) from the values published
in the data sheets to obtain the real internal disable
propagation delay.
1997 Nov 25
Open-drain outputs
Fig.40 Open-drain output circuit.
8.5
Increased drive capability of gates
To increase output drive, the inputs and outputs of gates in
the same package may be connected in parallel. It is
advisable to restrict parallel connection to gates within one
37
Philips Semiconductors
Product specification
User Guide
package to avoid large transient supply currents due to
different gate-switching times.
For further information, see chapter ‘Interfacing and
protection of circuit board inputs’.
8.6
Output capacitance
For push-pull outputs, no output capacitance is specified
because either the n-channel transistor or the p-channel
transistor creates a low-impedance path to the supply
rails.
Three-state outputs can be switched to the high
impedance OFF-state, and because many of them can be
connected to a bus line, the output capacitance is needed
to calculate the total capacitive load. For bus-driven
3-state outputs in a DIL package, the output capacitance
is 6 pF (typ.) and 20 pF (max.).
9
Fig.41 Worst-case input and output voltages over
an operating supply range of 4.5 V to 5.5 V.
STATIC NOISE IMMUNITY
The static noise immunity can be divided into:
• the static noise margin LOW. This is the voltage
difference between VILmax of the driven device and
VOLmax of the driver.
• the static noise margin HIGH. This is the difference
between VOHmin of the driver and VIHmin of the driven
device.
For 74HC devices, both the LOW level noise-margin and
the HIGH-level noise margin is 28% of VCC. This is a
considerable improvement over LSTTL where the
LOW-level noise margin is only 8% of VCC and the HIGH
level noise margin is just 14% of VCC. The margins are
even greater for HCMOS at higher supply voltages as
shown in Fig.41. As 74HCT devices have the same
switching levels as LSTTL, their noise margins are also the
same.
Fig.42 Typical input-to-output transfer
characteristic for 74HC and 74HCT
devices.
The superior noise immunity of the 74HC input can be
clearly seen from the voltage levels of the input-to-output
transfer characteristics shown in Figs 42 and 43.
1997 Nov 25
38
Philips Semiconductors
Product specification
User Guide
Table 12 Noise immunity and noise margin for 74HCT
and LSTTL device interfacing
74HCT
LSTTL
VIL max
(V) 0.8
0.8
VIHmin
(V) 2
2
VOLmax
(V) 0.33 (note 1)
0.1 (note 2)
0.4
VOHmin
(V) 3.84 (note 1)
4.4 (note 2)
2.7
Noise margins (V):
Fig.43 Input-to-output transfer characteristics for
TTL devices.
Table 11 shows the input noise margin of HCMOS devices
where like devices are interfaced. Output voltages are also
given.
74HCT
74HCU
VIL max
(V) 1.35
0.8
0.9
VIHmin
(V) 3.15
2
3.6
VOLmax
(V) 0.1
0.1
0.5
VOHmin
(V) 4.4
4.4
4
(V) 1.25
0.7
0.4
(V) 1.25
2.4
0.4
VNML
VNMH
0.4
0.7
from LS to LS
VNML
VNMH
0.4
0.7
from 74HCT
to 74HCT
VNML
VNMH
0.7
2.4
Whenever a 74HCT output drives either an LSTTL or a
74HCT input, the noise margin is better than when an
LSTTL device drives an LSTTL or 74HCT input. This
improvement is larger for VNMH owing to the superior
output sourcing current of the rail-to-rail HCMOS output
swing compared with the limited totem-pole pull-up output
voltage of LSTTL.
10 DYNAMIC NOISE IMMUNITY
As for static noise immunity, dynamic noise immunity can
be divided into two parts:
Table 12 shows the input noise margin of 74HCT devices
interfacing with LSTTL devices; the 74HCT or LSTTL
output is fully-loaded, VCC = 4.5 V and Tamb is 0 °C to
+70 °C (the only convenient temperature range when
using LSTTL characteristics).
1997 Nov 25
from LS to 74HCT
2. 20 µA load (i.e. 20 74HCT inputs).
Noise margin high
VNMH
0.47
1.84
1. 4 mA load (i.e. 10 LSTTL inputs).
Noise margin low
VNML
VNML
VNMH
Notes
Table 11 Noise immunity and noise margin for HCMOS
devices (VCC = 4.5 V)
74HC
from 74HCT to LS
• a dynamic noise margin LOW
• a dynamic noise margin HIGH.
For 74HC devices, both margins are similar; for 74HCT
devices, the dynamic noise margin LOW is the smaller of
the two. To plot it, a pulse of known magnitude, Vp, is
applied to the input of a device and its width, tW, is
increased until the device just begins to switch. The input
level on which Vp is based is equal to the switching voltage
minus the worst-case static noise margin LOW. The pulse
width is measured at half pulse height, Vp/2. The rise and
fall times, tr and tf are 0.6 ns.
39
Philips Semiconductors
Product specification
User Guide
Vp is then reduced in increments and tW for each new
value is ascertained.
The test is repeated for different supply voltages  for
74HC devices between 2 V and 6 V, and at 5 V for 74HCT
devices. A range of output currents, IO, are also used.
Increasing the DC load reduces the dynamic noise
immunity.
Figure 44 shows the amplitude of positive-going pulses
that can be withstood in the LOW state for 74HC and
74HCT devices. The curves are worst-case ones with
fully-loaded drivers, so a system using only 74HC or
74HCT devices will have 0.23 V more noise margin for all
tW.
For typical input switching thresholds of 1.4 V and 2.25 V
for 74HCT (VCC = 5 V) and 74HC (VCC = 4.5 V)
respectively, the noise margins will be 0.83 V [(1.4 − 0.8) +
0.23 V] larger for 74HCT and 1.13 V [(2.25 − 1.35) +
0.23 V] larger for 74HC devices.
The main causes of unwanted input pulses are spikes due
to outputs switching, which dumps large currents on the
GND lines, or reflections when long lines (longer than
about 32 cm) are driven. For more information on the
latter, see chapter ‘Replacing LSTTL and driving
transmission lines’.
The best example of an unwanted pulse generator is an
octal device with bus outputs of which seven are switching
simultaneously and the eighth, most remote, output is
LOW. Figure 45(a) shows the maximum pulse voltage
measured on the unswitched output of a 74HC/HCT374 as
a function of VCC. Figures 45(b) and 45(c) show this
maximum voltage and the pulse width as functions of the
number of outputs that are switching. It should be
emphasised that any pulses produced by switching
outputs won’t cause other devices to respond even in
worst-case conditions. This is because Fig.44 is based on
a worst-case VOL and the maximum expected pulse height
of Fig.45 occurs for a best-case VOL. So, even when a
pulse of the maximum expected height shown in
Fig.45 occurs, there is still a noise margin. This can be
verified by plotting the pulse heights of Fig.45 on the
curves of Figs 44(a) and 44(b).
1997 Nov 25
40
Philips Semiconductors
Product specification
User Guide
(b)
(a)
Fig.44 Amplitude of the positive-going pulses that can be withstood in the LOW state (worst-case, fully-loaded
driver) for (a) 74HCT devices and (b) 74HC devices.
Fig.45 (a) Amplitude of the voltage pulse (on pin 2, the most remove) due to switching seven of the bus-driver
outputs of a 74HC/HCT374 octal flip-flop; CL = 150 pF, Tamb = 25 °C. (b) Amplitude of the voltage pulse
(on pin 2) as a function of the number of outputs switched; VCC = 5 V, CL = 150 pF. (c) Pulse width as a
function of the number of outputs switched; VCC = 4.5 to 6 V, CL = 150 pF. For VCC = 2 V, the maximum
expected pulse width is about 10 ns.
1997 Nov 25
41
Philips Semiconductors
Product specification
User Guide
11 BUFFERED DEVICES
11.2
11.1
All 74HC and 74HCT devices have buffered outputs for
optimum performance. To demonstrate the benefits of
output buffering, consider what would happen without it. In
the single-stage device shown in Fig.47, the output
impedance depends on the DC input voltage.
Consequently, the noise margins at the output become a
function of the input voltage, even when VI is a legal HIGH
or LOW level.
Definition
Often the terms ‘buffer devices’, ‘buffered inputs’ or
‘buffered outputs’ are used without qualification and
originate from the very first unbuffered CMOS logic family
consisting of one-stage logic elements, usually gates. In
these devices, both input switching levels and output
impedances were not constant, so neither were output
rise/fall times or propagation delay times. The Jedec
JC40.2 committee define a buffered device to be at least
two active stages with the output independent of the input
logic voltage level and independent of the number of
inputs that are HIGH or LOW.
Output buffering
A buffer meeting this definition is the AND-function circuit
of Fig.46. The gain between input and output is high
enough to consider the output impedance to be
independent of the logic level at the input, and the output
impedance is not affected by the state of the logic inputs.
Fig.47 Unbuffered NAND gate.
The steady-state impedance of the circuit of Fig.47 is also
affected by the state of the inputs. Given that P1 and P2
have identical performances (same size), there are two
values of impedance for output HIGH; one when either
input is LOW and P1 or P2 conducts, and another when
both inputs are LOW and both P1 and P2 conduct.
Therefore, without output buffering, the state of output
conduction depends on the number of inputs that are
HIGH or LOW.
Fig.46 The minimum number of stages for a buffered
device is two. This 2-stage example is an
AND function.
11.3
An input is considered to be buffered when its switching
threshold is unaffected by the logic states of other inputs.
In the example of Fig.47 that has unbuffered inputs, the
switching threshold of input 1 varies with a HIGH level at
input 2, and vice versa. This is because the series
impedance of transistors N1 and N2 determines the
switching threshold of the device. The result can be seen
in Fig.48 where curve 1 + 2 occurs when the two inputs are
tied together, and curve 1 or 2 is the switching threshold
when the accompanying input is at VCC.
All 74HC and 74HCT devices comprise at least two stages
to minimize any pattern sensitivity of propagation delay
time. Buffering also improves static noise immunity due to
increased voltage gain, giving almost ideal transfer
characteristics.
The designation 74HCU is used to denote single-stage
devices. These have the same specification as 74HC
devices but their input and output voltage parameters are
relaxed. 74HCU devices don’t have the high gain of
74HC/HCT versions, which makes them more suitable for
use in RC or crystal oscillators and other feedback circuits
operating in the linear mode.
1997 Nov 25
Input buffering
For true input buffering, an input must have an inverter
stage with sufficient gain to ensure that logic levels give
independent on-chip levels. Some gates in the 74HC
series (usually AND or OR gates) have unbuffered inputs,
42
Philips Semiconductors
Product specification
User Guide
however all devices meet the family logic level
requirements. All 74HCT devices have buffered inputs.
The JEDEC standard test being developed for latch-up
specifies that the input/output current should be equal to
the maximum rating (±20 mA), and that VCC should also be
not more than twice VCCmax (14 V) for testing latch-up
immunity with excess supply voltage. HCMOS ICs have
been extensively subjected to the previously described
tests with test parameters far exceeding those quoted by
JEDEC. In no case did latch-up occur. For example, it has
been determined that an HCMOS input can typically
withstand continuous current (5 s on, 15 s off) of 100 mA
to 120 mA, or 1µs pulses of 300 mA with a duty factor of
0.001. An input can also withstand a discharge from a
200 pF capacitor charged to 330 V. An HCMOS output
can withstand continuous current (5 s on, 15 s off) of 200
mA to 300 mA, or 1 µs pulses of 400 mA with a duty factor
of 0.001. However, because there is an internal polysilicon
100 Ω resistor in series with all HCMOS inputs, the input
voltages required to achieve these current levels are so
high (VI = VCC + 0.7 V + 100II) that it is unlikely that they
could occur in practice, even in a 6 V system with severe
glitches. Moreover, beyond these current levels, excessive
heating occurs or aluminium tracks or bond wires
breakdown. It is therefore reasonable to conclude that
HCMOS logic ICs are completely latch-up free.
Fig.48 Example of different switching levels in
unbuffered inputs.
12 PERFORMANCE OF OSCILLATORS
When HCMOS devices are used in RC, crystal or Schmitt
trigger oscillators or in analog amplifiers:
• a supply voltage of at least 3 V is required. Below this
value, the transconductance of crystal oscillators is too
low to start oscillations. In analog circuits, insufficient
output current is available to drive external components;
For further information, see chapter ‘Standardizing
latch-up immunity tests’ in the Designers Guide,
High-speed CMOS.
• slow input rise and fall times cause the input stage of a
HCMOS device to draw current. This additional
quiescent supply current ∆ICC is given in the data sheets
for 74HCT devices since these can be used as LSTTL
replacements and may be driving a significant load. The
total ICC for 74HC devices can be calculated by
multiplying the value of ICC read from Fig.14 by the unit
load coefficient given in the data sheet for the 74HCT
device;
14 DROP-IN REPLACEMENTS FOR LSTTL
74HCT devices are power-saving, drop-in replacements
for LSTTL devices. Because most systems are operated at
frequencies far below the maximum possible, 74HCT
devices can also be used to good effect in systems using
ALS, AS, S, and FAST devices.
• in general, frequency stability won’t be affected by
supply voltage, so long as the permissible output
currents of the devices are not exceeded.
Fan-out should be considered when replacing a TTL
device by a 74HCT device. TTL fan-out is usually
expressed in unit loads (ULs) and the load is specified to
be an input of the same family. In fact, TTL fan-out is
determined by the ability of the outputs to sink current (a
TTL input usually sources current). Table 13 shows the
fan-out of 74HCT to the different TTL families.
For further information, see chapters ‘Crystal oscillators’
and ‘Astable multivibrators’.
13 LATCH-UP FREE
The fan-outs given in Table 13 are derived at a voltage
drop of max. 0.4 V (VOL). In the “74” TTL series, an
extended VOL figure is often seen, e.g. 8 mA at 0.5 V
voltage drop for LSTTL. If this figure is used to determine
the fan-out of the TTL device it can result in a higher
fan-out than is possible with 74HCT. This can be resolved
by replacing as many of the driven TTL parts as possible
by 74HCT devices to reduce the sink current requirement
Latch-up is the creation of a low-impedance path between
the power supply rails caused by the triggering of parasitic
bipolar structures (SCRs) by input, output or supply
over-voltages. These overvoltages induce currents that
can exceed maximum device ratings. When the
low-impedance path remains after removal of the
triggering voltage, the device is said to have latch-up.
1997 Nov 25
43
Philips Semiconductors
Product specification
User Guide
(the 74HCT input current is negligible). In addition, power
dissipation is reduced significantly by using 74HCT.
The wider supply voltage range of HCMOS together with
its lower power dissipation virtually eliminates problems
caused by voltage drops along power buses between
cards in a system. It is possible for a circuit to pick up
severe noise spikes of differential voltages via an edge
connector. Such pick-up can exceed the CMOS maximum
ratings if not limited by a 10 kΩ series resistor in the
HCMOS logic line. This will limit current to ±20 mA for
external voltages of up to ±200 V, however, for correct
functioning, the DC input current should be kept below
those values stated in ‘Input/output protection’. The
recommended board edge input protection is shown in
Fig.50.
Table 13 Fan-out of 74HCT to TTL circuits
74HCT
TTL
LS
ALS
FAST
S&
AS
standard
output
2
10
20
6
2
bus-driver
output
3
15
30
10
3
15 BUS SYSTEMS
In the circuit of Fig.50, if the input diode current exceeds
the maximum input current, a HIGH-to-LOW level shifter
should be used (e.g. 74HC4049 or 74HC4050).
CMOS is being used to an increasing extent in
microprocessor bus systems following the introduction of
versions of the popular NMOS processors.
There are several constraints imposed on microprocessor
systems in industrial applications, such as
electrically-noisy environments, battery-standby
requirements and sealed, gas-tight enclosures. HCMOS
bus systems, e.g. the CMOS STD bus (a non-proprietary
CMOS bus standard) provides a solution to all these
problems. It offers superior noise immunity, equal
operating speed, lower power dissipation, wider supply
voltage range, extended temperature range, and
enhanced reliability.
For optimum results, use only 74HC devices in circuits
which communicate directly with the bus. This allows a
new bus termination to be introduced (see Fig.49(b))
which, unlike the conventional TTL bus termination, draws
no heavy DC current and is more suited to HCMOS
outputs.
Fig.50 Example of the board edge input protection
circuit.
For further information, see chapter ‘Interfacing and
protection of circuit board inputs’.
Since HCMOS bus-drivers do not have built-in hysteresis,
slowly-rising pulses should be avoided or devices with
Schmitt-trigger action should be used, such as the flip-flop
series 74HC/HCT73, 74, 107, 109, 112, or the dedicated
Schmitt triggers 74HC/HCT14 and 132. The rise and fall
times can be derived from the information given in the
section ‘Propagation delays and transition times’ of this
User Guide.
Fig.49 Bus terminations. (a) Conventional
termination for TTL buses. (b) Proposed
termination for CMOS STD bus equivalents.
1997 Nov 25
44
Philips Semiconductors
Product specification
User Guide
The use of SO packages with their low pin capacitances is
recommended for HCMOS analog designs. Table 14 gives
the pin-to-pin capacitances for the plastic DIL and SO
packages used for HCMOS. Measurements were made
using a dummy package with all unused pins connected to
ground.
16 PACKAGE PIN CAPACITANCE
In purely digital circuits, the input capacitance or
three-state output capacitance is sufficient to determine
the dynamic characteristics. However, when a HCMOS
device is used in the linear region, it is necessary to take
pin capacitance into account, e.g. to prevent crosstalk in
analog switches or peaks in the frequency response of
PLLs.
Table 14 Typical pin capacitances (pF) of SO and DIL packages
SO-14 & SO-16
DIL-16
0.41
0.21
0.97
0.37
SO-20
DIL-20
0.65
0.25
1.12
0.40
SO-24
DIL-24
0.65
0.33
1.64
0.65
0.30
0.12
0.70
0.28
capacitance to ground of:
corner pins
all other pins
any end two pins
all other pins
any end three pins
all other pins
capacitance between adjacent pins:
including a corner pin
all other pins
0.15
0.04
0.40
0.13
any end three pins
all other pins
0.28
0.14
any end three pins
all other pins
1997 Nov 25
45
0.49
0.22
Philips Semiconductors
Product specification
User Guide
17 POWER-ON RESET
Table 15 Sensitivity of HCMOS POR circuitry to VCC
reduction
The power-on reset (POR) circuit used to automatically set
HCMOS ICs in a defined reset state after power-up is
shown in Fig.51.
VCC (V)
2
4.5
6
VLmax (V)
VLmax (V)
VLmax (V)
8
0.8
2.2
2.8
6
0.75
2.2
2.8
4
0.7
2.2
2.8
2
0.6
2.1
2.8
1
0.5
2.0
2.8
0.5
0.4
1.9
2.8
0.1
0.4
1.9
2.8
0.05
0.4
−
−
0.02
0.3
−
−
0.015
0.15
1.7
2.5
tw (µs)
Fig.51 Power-on reset circuit.
The time taken for a transition to propagate from R to Q is
about the time taken for the reset action to take effect. Also
of course, node A in Fig.51 must rise to a level above the
switching level of the NOR gate. Because of this, the Q
output of the IC may initially follow the VCC ramp as
indicated in Fig.53. If the VCC ramp is fast (typically less
than 100 ns), the amplitude of the Q output pulse can
exceed VCC/2 and have a duration of about 10 ns.
When the IC is powered-up, node A follows the rise of VCC
through C1 and the circuit is reset. When the gate voltage
of transistor N1 exceeds its threshold level (typically 0.7 V)
because it is biased with VCC via transistor P1, capacitor
C1 discharges and pulls node A below the switching level
of the NOR gate. The IC cannot be used during the POR
release time which is the discharge time of C1 (typically 3
µs at VCC = 4.5 V and 35 µs at VCC = 2 V). The sensitivity
of the POR circuit to supply voltage reduction is indicated
in Table 15. The typical values of parameters tw and VL
used in Table 15 are illustrated in Fig.52.
Fig.53 Initial output pulse during power-up.
Normally, the Q output pulse is negligible because the VCC
ramp is slow (typically more than 0.5 µs) due to the
charging time of large-value smoothing and decoupling
capacitors. With a slow VCC ramp, the amplitude of the Q
output pulse remains well below the switching level of the
succeeding stage. In any event, it is most unlikely that a
system will be triggered by the Q output pulse because it
only occurs during power-up.
Fig.52 VL as a function of the duration of a LOW
pulse on the supply voltage.
1997 Nov 25
46