29XXX Rev ** 24.8mm [0.975"] Top View: (as viewed attached to bottom of POD) CY8C29000A Side 27.6mm [1.085"] Top View McMaster/Carr 91185A558 Mask (alignment cap) for 28 pin feet (included) Bottom View Description: CY3250-29XXX POD 100 pin TQFP OCD. Hirose cable connector (P/N: DF12-5.0-20DP-0.5V-81) with retension mechanism included. Compatible with: SF-QFE100SC-L-CY, 100 pin, 0.5mm, 8mm body, TQFP foot C3846, SSOP28 foot C3850, TQFP44 foot C3847, SSOP48 foot C3849, SOIC28 foot C4104, PDIP28 foot Side View Interface to 28 pin feet requires Mask for proper alignment to these feet Mask 1 of 2 Page:___ EA-8C29000-NQ-01 Drawing © 2005 IRONWOOD ELECTRONICS, INC. Tele: (800) 404-0204 www.ironwoodelectronics.com Status: 3:1 Scale: ____ Rev: E Drawing: M. Tully Date: 10/5/05 File: EA-8C29000-NQ-01 Dwg.mcd Modified: 8/15/06, MT Tolerances: diameters ±0.03mm [±0.001”], PCB perimeters ±0.13mm [±0.005”], PCB thicknesses ±0.18mm [±0.007"], pitches (from true position) ±0.08mm [±0.003"], all other tolerances ±0.13mm [±0.005”] unless stated otherwise. Materials and specifications are subject to change without notice. POD clearance, with respect to center of target pattern 1.085" X McMaster/Carr 91185A558 Y To ICE Pod 0.575" Flex Cable A 0.975" B C (mask, if required) Pod perimeter Foot Part number Description C3846 SSOP28 foot C3849 Mask required A B C X yes 0.875" 0.300" 0.275" 0.596" 0.513" SOIC28 foot yes 0.875" 0.300" 0.275" 0.596" 0.513" C4104 PDIP28 foot yes 1.000" * 0.425" * 0.400" * 0.596" 0.513" C3850 TQFP44 foot no 0.850" 0.275" 0.250" 0.596" 0.488" C3846 SSOP48 foot no 0.875" 0.300" 0.275" 0.596" 0.513" SF-QFE100SC-L-CY TQFP100 foot no 0.900" 0.325" 0.300" 0.621" 0.488" center of target land pattern (SSOP28 shown) Y * assumes body of the socket pin of the PDIP foot is soldered flush to top of target PCB 2 of 2 Page:___ EA-8C29000-NQ-01 Drawing © 2005 IRONWOOD ELECTRONICS, INC. Tele: (800) 404-0204 www.ironwoodelectronics.com Status: 3:1 Scale: ____ Rev: E Drawing: M. Tully Date: 10/5/05 File: EA-8C29000-NQ-01 Dwg.mcd Modified: 8/15/06, MT Tolerances: diameters ±0.03mm [±0.001”], PCB perimeters ±0.13mm [±0.005”], PCB thicknesses ±0.18mm [±0.007"], pitches (from true position) ±0.08mm [±0.003"], all other tolerances ±0.13mm [±0.005”] unless stated otherwise. Materials and specifications are subject to change without notice.