PCF85063ATL Tiny Real-Time Clock/calendar with alarm function and I2C-bus Rev. 2 — 15 April 2013 Product data sheet 1. General description The PCF85063ATL is a CMOS1 Real-Time Clock (RTC) and calendar optimized for low power consumption. An offset register allows fine-tuning of the clock. All addresses and data are transferred serially via the two-line bidirectional I2C-bus. Maximum data rate is 400 kbit/s. The register address is incremented automatically after each written or read data byte. 2. Features and benefits Provides year, month, day, weekday, hours, minutes, and seconds based on a 32.768 kHz quartz crystal Clock operating voltage: 0.9 V to 5.5 V Low current; typical 0.27 A at VDD = 3.0 V and Tamb = 25 C 400 kHz two-line I2C-bus interface (at VDD = 1.8 V to 5.5 V) Programmable clock output for peripheral devices (32.768 kHz, 16.384 kHz, 8.192 kHz, 4.096 kHz, 2.048 kHz, 1.024 kHz, and 1 Hz) Selectable integrated oscillator load capacitors for CL = 7 pF or CL = 12.5 pF Alarm function Countdown timer Minute and half minute interrupt Internal Power-On Reset (POR) Programmable offset register for frequency adjustment 3. Applications 1. Digital still camera Digital video camera Printers Copy machines Mobile equipment Battery powered devices The definition of the abbreviations and acronyms used in this data sheet can be found in Section 19. PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 4. Ordering information Table 1. Ordering information Type number Package PCF85063ATL Name Description Version HXSON10 plastic thermal enhanced extremely thin small outline package; no leads; 10 terminals; body 2.6 2.6 0.5 mm SOT1197-1 4.1 Ordering options Table 2. Ordering options Product type number IC revision Sales item (12NC) Delivery form PCF85063ATL/1 1 935299022118 tape and reel, 13 inch 5. Marking Table 3. Marking codes Product type number Marking code PCF85063ATL/1 063A 6. Block diagram 26&2 26&, N+] 26&,//$725 ',9,'(5 32:(521 5(6(7 &/2&. &$/,%5$7,21 2))6(7 9'' 6<67(0 &21752/ 966 6'$ 6&/ O&%86 ,17(5)$&( &/.2( &/2&.287 &/.287 ,17(55837 &21752/ ,17 5($/7,0( &/2&. $/$50$1' 7,0(5 &21752/ 3&)$7/ Fig 1. PCF85063ATL Product data sheet Block diagram of PCF85063ATL All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 2 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 7. Pinning information 7.1 Pinning 3&)$7/ 26&, 9'' 26&2 &/.287 &/.2( QF ,17 6&/ 966 6'$ DDD 7UDQVSDUHQWWRSYLHZ For mechanical details, see Figure 30. Fig 2. Pin configuration for HXSON10 (PCF85063ATL) 7.2 Pin description Table 4. Symbol Pin Type Description OSCI 1 input oscillator input OSCO 2 output oscillator output CLKOE 3 input CLKOUT enable or disable pin; enable is active HIGH INT 4 output interrupt output (open-drain) VSS 5[1] supply ground supply voltage SDA 6 input/output serial data line SCL 7 input serial clock input n.c. 8 - not connected CLKOUT 9 output clock output (push-pull) VDD 10 supply supply voltage [1] PCF85063ATL Product data sheet Pin description The die paddle (exposed pad) is connected to VSS and should be electrically isolated. All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 3 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8. Functional description The PCF85063ATL contains 18 8-bit registers with an auto-incrementing register address, an on-chip 32.768 kHz oscillator with integrated capacitors, a frequency divider which provides the source clock for the Real-Time Clock (RTC) and calender, and an I2C-bus interface with a maximum data rate of 400 kbit/s. The built-in address register will increment automatically after each read or write of a data byte up to the register 11h. After register 11h, the auto-incrementing will wrap around to address 00h (see Figure 3). DGGUHVVUHJLVWHU K K K DXWRLQFUHPHQW K )K K K ZUDSDURXQG DDD Fig 3. Handling address registers All registers (see Table 5) are designed as addressable 8-bit parallel registers although not all bits are implemented. The first two registers (memory address 00h and 01h) are used as control and status register. The register at address 02h is an offset register allowing the fine-tuning of the clock; and at 03h is a free RAM byte. The addresses 04h through 0Ah are used as counters for the clock function (seconds up to years counters). Address locations 0Bh through 0Fh contain alarm registers which define the conditions for an alarm. The registers at 10h and 11h are for the timer function. The Seconds, Minutes, Hours, Days, Months, and Years as well as the corresponding alarm registers are all coded in Binary Coded Decimal (BCD) format. When one of the RTC registers is written or read, the contents of all time counters are frozen. Therefore, faulty writing or reading of the clock and calendar during a carry condition is prevented. For details on maximum access time, see Section 8.4 on page 22. PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 4 of 54 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx NXP Semiconductors PCF85063ATL Product data sheet 8.1 Registers organization Table 5. Registers overview Bit positions labeled as - are not implemented. After reset, all registers are set according to Table 8 on page 9. Address Register name Bit Reference 7 6 5 4 3 2 1 0 12_24 CAP_SEL Control and status registers 00h Control_1 EXT_TEST - STOP SR - CIE 01h Control_2 AIE AF MI HMI TF COF[2:0] 02h Offset MODE OFFSET[6:0] 03h RAM_byte B[7:0] Section 8.2.1 Section 8.2.2 Section 8.2.3 Section 8.2.4 Time and date registers Seconds OS SECONDS (0 to 59) Section 8.3.1 05h Minutes - MINUTES (0 to 59) Section 8.3.2 06h Hours - - AMPM 07h Days - - DAYS (1 to 31) 08h Weekdays - - - - 09h Months - - - MONTHS (1 to 12) 0Ah Years YEARS (0 to 99) Section 8.3.7 HOURS (1 to 12) in 12 hour mode Section 8.3.3 HOURS (0 to 23) in 24 hour mode Section 8.3.4 - WEEKDAYS (0 to 6) Section 8.3.5 Section 8.3.6 Alarm registers 0Bh Second_alarm AEN_S SECOND_ALARM (0 to 59) Section 8.5.1 0Ch Minute_alarm AEN_M MINUTE_ALARM (0 to 59) Section 8.5.2 0Dh Hour_alarm AEN_H - AMPM HOUR_ALARM (1 to 12) in 12 hour mode Section 8.5.3 0Eh Day_alarm AEN_D - DAY_ALARM (1 to 31) 0Fh Weekday_alarm AEN_W - - - Section 8.5.4 - WEEKDAY_ALARM (0 to 6) Section 8.5.5 Timer registers 5 of 54 © NXP B.V. 2013. All rights reserved. 10h Timer_value T[7:0] 11h Timer_mode - Section 8.6.1 - - TCF[1:0] TE TIE TI_TP Section 8.6.2 PCF85063ATL HOUR_ALARM (0 to 23) in 24 hour mode Tiny Real-Time Clock/calendar with alarm function and I2C-bus Rev. 2 — 15 April 2013 All information provided in this document is subject to legal disclaimers. 04h PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8.2 Control registers 8.2.1 Register Control_1 Table 6. Control_1 - control and status register 1 (address 00h) bit description Bit Symbol 7 EXT_TEST 6 - 5 STOP 4 Value - 2 CIE 1 external clock test mode Section 8.2.1.1 normal mode 1 external clock test mode 0 unused - STOP bit Section 8.2.1.2 0[1] RTC clock runs 1 RTC clock is stopped; all RTC divider chain flip-flops are asynchronously set logic 0 software reset 0[1] no software reset 1 initiate software reset[2]; this bit always returns a 0 when read 0 - correction interrupt enable Section 8.2.3 no correction interrupt generated 1 interrupt pulses are generated at every correction cycle 12 or 24 hour mode 0[1] 24 hour mode is selected 1 12 hour mode is selected CAP_SEL internal oscillator capacitor selection for quartz crystals with a corresponding load capacitance 0[1] 7 pF 1 12.5 pF [1] Default value. [2] For a software reset, 01011000 (58h) must be sent to register Control_1 (see Section 8.2.1.3). 8.2.1.1 Section 8.2.1.3 unused 0[1] 12_24 0 Reference 0[1] SR 3 Description Section 8.3.3 Section 8.5.3 - EXT_TEST: external clock test mode A test mode is available which allows for on-board testing. In this mode, it is possible to set up test conditions and control the operation of the RTC. The test mode is entered by setting bit EXT_TEST in register Control_1. Then pin CLKOUT becomes an input. The test mode replaces the internal clock signal with the signal applied to pin CLKOUT. The signal applied to pin CLKOUT should have a minimum pulse width of 300 ns and a maximum period of 1000 ns. The internal clock, now sourced from CLKOUT, is divided down to 1 Hz by a 26 divide chain called a prescaler. The prescaler can be set into a known state by using bit STOP. When bit STOP is set, the prescaler is reset to 0. (STOP must be cleared before the prescaler can operate again.) PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 6 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus From a stop condition, the first 1 second increment will take place after 32 positive edges on pin CLKOUT. Thereafter, every 64 positive edges cause a 1 second increment. Remark: Entry into test mode is not synchronized to the internal 64 Hz clock. When entering the test mode, no assumption as to the state of the prescaler can be made. Operation example: 1. Set EXT_TEST test mode (register Control_1, bit EXT_TEST = 1). 2. Set STOP (register Control_1, bit STOP = 1). 3. Clear STOP (register Control_1, bit STOP = 0). 4. Set time registers to desired value. 5. Apply 32 clock pulses to pin CLKOUT. 6. Read time registers to see the first change. 7. Apply 64 clock pulses to pin CLKOUT. 8. Read time registers to see the second change. Repeat 7 and 8 for additional increments. 8.2.1.2 STOP: STOP bit function The function of the STOP bit (see Figure 4) is to allow for accurate starting of the time circuits. The STOP bit function causes the upper part of the prescaler (F2 to F14) to be held in reset and thus no 1 Hz ticks are generated. It also stops the output of clock frequencies below 8 kHz on pin CLKOUT. 26&,//$7256723 '(7(&725 26&,//$725 +] ) +] ) +] ) VHWWLQJWKH26IODJ +] 5(6(7 ) 5(6(7 +] ) 5(6(7 +]WLFN 6723 DDD Fig 4. STOP bit functional diagram The time circuits can then be set and do not increment until the STOP bit is released (see Figure 5 and Table 7). PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 7 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus Table 7. First increment of time circuits after STOP bit release Bit Prescaler bits STOP F0F1-F2 to F14 [1] 1 Hz tick Time Comment hh:mm:ss Clock is running normally 0 12:45:12 01-0 0001 1101 0100 prescaler counting normally STOP bit is activated by user. F0F1 are not reset and values cannot be predicted externally 1 12:45:12 prescaler is reset; time circuits are frozen 08:00:00 prescaler is reset; time circuits are frozen XX-0 0000 0000 0000 08:00:00 prescaler is now running XX-1 0000 0000 0000 08:00:00 - XX-0 1000 0000 0000 08:00:00 - 08:00:00 - : : : 11-1 1111 1111 1110 08:00:00 - 00-0 0000 0000 0001 08:00:01 0 to 1 transition of F14 increments the time circuits 10-0 0000 0000 0001 08:00:01 - : : : XX-0 0000 0000 0000 New time is set by user 1 XX-0 0000 0000 0000 STOP bit is released by user 0 XX-1 1000 0000 0000 WR V 08:00:01 - 00-0 0000 0000 0000 08:00:01 - 10-0 0000 0000 0000 08:00:01 - : : : 11-1 1111 1111 1110 08:00:01 - 00-0 0000 0000 0001 08:00:02 0 to 1 transition of F14 increments the time circuits 11-1 1111 1111 1111 V DDD [1] F0 is clocked at 32.768 kHz. The lower two stages of the prescaler (F0 and F1) are not reset. And because the I2C-bus is asynchronous to the crystal oscillator, the accuracy of restarting the time circuits is between zero and one 8.192 kHz cycle (see Figure 5). +] VWRSUHOHDVHG VWRV Fig 5. DDD STOP bit release timing The first increment of the time circuits is between 0.507813 s and 0.507935 s after STOP bit is released. The uncertainty is caused by the prescaler bits F0 and F1 not being reset (see Table 7) and the unknown state of the 32 kHz clock. PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 8 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8.2.1.3 Software reset A reset is automatically generated at power-on. A reset can also be initiated with the software reset command. Software reset command means setting bits 6, 4, and 3 in register Control_1 (00h) logic 1 and all other bits logic 0 by sending the bit sequence 01011000 (58h), see Figure 6. VODYHDGGUHVV 6'$ V DGGUHVVK 5: $ VRIWZDUHUHVHWK $ $ 36 6&/ LQWHUQDO UHVHWVLJQDO DDD Fig 6. Software reset command In reset state all registers are set according to Table 8 and the address pointer returns to address 00h. PCF85063ATL Product data sheet Table 8. Registers reset values Address Register name Bit 7 6 5 4 3 2 1 0 00h Control_1 0 0 0 0 0 0 0 0 01h Control_2 0 0 0 0 0 0 0 0 02h Offset 0 0 0 0 0 0 0 0 03h RAM_byte 0 0 0 0 0 0 0 0 04h Seconds 1 0 0 0 0 0 0 0 05h Minutes 0 0 0 0 0 0 0 0 06h Hours 0 0 0 0 0 0 0 0 07h Days 0 0 0 0 0 0 0 1 08h Weekdays 0 0 0 0 0 1 1 0 09h Months 0 0 0 0 0 0 0 1 0Ah Years 0 0 0 0 0 0 0 0 0Bh Second_alarm 1 0 0 0 0 0 0 0 0Ch Minute_alarm 1 0 0 0 0 0 0 0 0Dh Hour_alarm 1 0 0 0 0 0 0 0 0Eh Day_alarm 1 0 0 0 0 0 0 0 0Fh Weekday_alarm 1 0 0 0 0 0 0 0 10h Timer_value 0 0 0 0 0 0 0 0 11h Timer_mode 0 0 0 1 1 0 0 0 All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 9 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus The PCF85063ATL resets to: Time — 00:00:00 Date — 20000101 Weekday — Saturday 8.2.2 Register Control_2 Table 9. Control_2 - control and status register 2 (address 01h) bit description Bit Symbol 7 AIE 6 Value Description Reference alarm interrupt Section 8.2.2.1 Section 8.5.6 0[1] disabled 1 enabled AF alarm flag 0[1] read: alarm flag inactive Section 8.2.2.1 Section 8.5.6 write: alarm flag is cleared 1 read: alarm flag active write: alarm flag remains unchanged 5 MI 4 0[1] disabled 1 enabled HMI 3 half minute interrupt 0[1] disabled 1 enabled TF 2 to 0 [1] minute interrupt COF[2:0] timer flag 0[1] no timer interrupt generated 1 flag set when timer interrupt generated see Table 11 CLKOUT control Section 8.2.2.2 Section 8.2.2.3 Section 8.2.2.2 Section 8.2.2.3 Section 8.2.2.1 Section 8.2.2.3 Section 8.6.3 Section 8.2.2.4 Default value. PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 10 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8.2.2.1 Alarm interrupt +0, 6(&21'6&2817(5 7)7,0(5)/$* 0,187(6&2817(5 7,( 6(7 &/($5 0, &2817'2:1&2817(5 7( WRLQWHUIDFH UHDG7) 38/6( *(1(5$725 75,**(5 &/($5 IURPLQWHUIDFH FOHDU7) 7,B73 $)$/$50)/$* VHWDODUP IODJ$) ,17 WRLQWHUIDFH UHDG$) $,( H[DPSOH 6(7 $,( &/($5 IURPLQWHUIDFH FOHDU$) 38/6( *(1(5$725 75,**(5 RIIVHWFLUFXLW DGGVXEVWUDFW SXOVH &,( &/($5 IURPLQWHUIDFH VHW&,( DDD When AIE bit is disabled, pin INT remains high-impedance. Fig 7. Interrupt scheme AIE: This bit activates or deactivates the generation of an interrupt when AF is asserted, respectively. AF: When an alarm occurs, AF is set logic 1. This bit maintains its value until overwritten by command. To prevent one flag being overwritten while clearing another, a logic AND is performed during a write access. 8.2.2.2 MI and HMI: minute and half minute interrupt The minute interrupt (bit MI) and half minute interrupt (bit HMI) are pre-defined timers for generating interrupt pulses on pin INT; see Figure 8. The timers are running in sync with the seconds counter (see Table 19 on page 18). When starting MI, the first interrupt will be generated after 1 second to 59 seconds. When starting HMI, the first interrupt will be generated after 1 second to 29 seconds. Subsequent periods do not have such a delay. The timers can be enabled independently from one another. However, a minute interrupt enabled on top of a half minute interrupt is not distinguishable. PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 11 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus VHFRQGVFRXQWHU PLQXWHVFRXQWHU ,17ZKHQ0,HQDEOHG 7)ZKHQ0,HQDEOHG DDD In this example, the TF flag is not cleared after an interrupt. Fig 8. Table 10. INT example for MI Effect of bits MI and HMI on INT generation Minute interrupt (bit MI) Half minute interrupt (bit HMI) Result 0 0 no interrupt generated 1 0 an interrupt every minute 0 1 an interrupt every 30 s 1 1 an interrupt every 30 s The duration of the timer is affected by the register Offset (see Section 8.2.3). Only when OFFSET[6:0] has the value 00h the periods are consistent. 8.2.2.3 TF: timer flag The timer flag (bit TF) is set logic 1 on the first trigger of MI, HMI, or the countdown timer. The purpose of the flag is to allow the controlling system to interrogate what caused the interrupt: timer or alarm. The flag can be read and cleared by command. The status of the timer flag TF can affect the INT pulse generation depending on the setting of TI_TP (see Section 8.6.2 “Register Timer_mode” on page 27): • When TI_TP is set logic 1 – an INT pulse is generated independent of the status of the timer flag TF – TF stays set until it is cleared – TF does not affect INT – the countdown timer runs in a repetitive loop and keeps generating timed periods • When TI_TP is set logic 0 – the INT generation follows the TF flag – TF stays set until it is cleared – If TF is not cleared before the next coming interrupt, no INT is generated – the countdown timer stops after the first countdown 8.2.2.4 COF[2:0]: Clock output frequency A programmable square wave is available at pin CLKOUT. Operation is controlled by the COF[2:0] bits in the register Control_2. Frequencies of 32.768 kHz (default) down to 1 Hz can be generated for use as a system clock, microcontroller clock, input to a charge pump, or for calibration of the oscillator. PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 12 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus Pin CLKOUT is a push-pull output and enabled at power-on. CLKOUT can be disabled by setting COF[2:0] to 111 or by setting CLKOE LOW. When disabled, the CLKOUT is LOW. The duty cycle of the selected clock is not controlled. However, due to the nature of the clock generation, all clock frequencies except 32.768 kHz have a duty cycle of 50 : 50. The STOP bit function can also affect the CLKOUT signal, depending on the selected frequency. When the STOP bit is set logic 1, the CLKOUT pin generates a continuous LOW for those frequencies that can be stopped. For more details of the STOP bit function, see Section 8.2.1.2. Table 11. CLKOUT frequency selection COF[2:0] CLKOUT frequency (Hz) Typical duty cycle[1] Effect of STOP bit 000[2] 32768 60 : 40 to 40 : 60 no effect 001 16384 50 : 50 no effect 010 8192 50 : 50 no effect 011 4096 50 : 50 CLKOUT = LOW 100 2048 50 : 50 CLKOUT = LOW 101 1024 50 : 50 CLKOUT = LOW 110 1[3] 50 : 50 CLKOUT = LOW 111 CLKOUT = LOW - - [1] Duty cycle definition: % HIGH-level time : % LOW-level time. [2] Default value. [3] 1 Hz clock pulses are affected by offset correction pulses. 8.2.3 Register Offset The PCF85063ATL incorporates an offset register (address 02h) which can be used to implement several functions, such as: • Accuracy tuning • Aging adjustment • Temperature compensation Table 12. Offset - offset register (address 02h) bit description Bit Symbol 7 MODE Value offset mode 0[1] 1 6 to 0 [1] Description OFFSET[6:0] see Table 13 normal mode: offset is made once every two hours course mode: offset is made every 4 minutes offset value Default value. For MODE = 0, each LSB introduces an offset of 4.34 ppm. For MODE = 1, each LSB introduces an offset of 4.069 ppm. The values of 4.34 ppm and 4.069 ppm are based on a nominal 32.768 kHz clock. The offset value is coded in two’s complement giving a range of +63 LSB to 64 LSB. PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 13 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus Table 13. Offset values OFFSET[6:0] Offset value in decimal Offset value in ppm Normal mode MODE = 0 Fast mode MODE = 1 0111111 +63 +273.420 +256.347 0111110 +62 +269.080 +252.278 : : : : 0000010 +2 +8.680 +8.138 0000001 +1 +4.340 +4.069 0000000[1] 0 0[1] 0[1] 1111111 1 4.340 4.069 1111110 2 8.680 8.138 : : : : 1000001 63 273.420 256.347 1000000 64 277.760 260.416 [1] Default value. The correction is made by adding or subtracting clock correction pulses, thereby changing the period of a single second but not by changing the oscillator frequency. It is possible to monitor when correction pulses are applied. To enable correction interrupt generation, bit CIE (register Control_1) has to be set logic 1. At every correction cycle a pulse is generated on pin INT. The pulse width depends on the correction mode. If multiple correction pulses are applied, an interrupt pulse is generated for each correction pulse applied. PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 14 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8.2.3.1 Correction when MODE = 0 The correction is triggered once every two hours and then correction pulses are applied once per minute until the programmed correction values have been implemented. Table 14. Correction pulses for MODE = 0 Correction value Update every nth hour Minute Correction pulses on INT per minute[1] +1 or 1 2 00 1 +2 or 2 2 00 and 01 1 +3 or 3 2 00, 01, and 02 1 : : : : +59 or 59 2 00 to 58 1 +60 or 60 2 00 to 59 1 +61 or 61 2 00 to 59 1 2nd and next hour 00 1 2 00 to 59 1 2nd and next hour 00 and 01 1 02 00 to 59 1 2nd and next hour 00, 01, and 02 1 02 00 to 59 1 2nd and next hour 00, 01, 02, and 03 1 +62 or 62 +63 or 63 64 [1] The correction pulses on pin INT are 1⁄64 s wide. In MODE = 0, any timer or clock output using a frequency below 64 Hz is affected by the clock correction (see Table 15). Table 15. Effect of correction pulses on frequencies for MODE = 0 Frequency (Hz) Effect of correction CLKOUT 32768 no effect 16384 no effect 8192 no effect 4096 no effect 2048 no effect 1024 no effect 1 affected Timer source clock 4096 PCF85063ATL Product data sheet no effect 64 no effect 1 affected 1⁄ 60 affected All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 15 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8.2.3.2 Correction when MODE = 1 The correction is triggered once every four minutes and then correction pulses are applied once per second up to a maximum of 60 pulses. When correction values greater than 60 pulses are used, additional correction pulses are made in the 59th second. Clock correction is made more frequently in MODE = 1; however, this can result in higher power consumption. Table 16. Correction pulses for MODE = 1 Correction value Update every nth minute Second Correction pulses on INT per second[1] +1 or 1 2 00 1 +2 or 2 2 00 and 01 1 +3 or 3 2 00, 01, and 02 1 : : : : +59 or 59 2 00 to 58 1 +60 or 60 2 00 to 59 1 +61 or 61 2 00 to 58 1 2 59 2 +62 or 62 +63 or 63 64 [1] 2 00 to 58 1 2 59 3 2 00 to 58 1 2 59 4 2 00 to 58 1 2 59 5 The correction pulses on pin INT are 1⁄1024 s wide. For multiple pulses, they are repeated at an interval of s. 1⁄ 512 In MODE = 1, any timer source clock using a frequency below 1.024 kHz is also affected by the clock correction (see Table 17). Table 17. Effect of correction pulses on frequencies for MODE = 1 Frequency (Hz) Effect of correction CLKOUT 32768 no effect 16384 no effect 8192 no effect 4096 no effect 2048 no effect 1024 no effect 1 affected Timer source clock PCF85063ATL Product data sheet 4096 no effect 64 affected 1 affected 1⁄ 60 affected All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 16 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8.2.3.3 Offset calibration workflow The calibration offset has to be calculated based on the time. Figure 9 shows the workflow how the offset register values can be calculated: 0HDVXUHWKHIUHTXHQF\RQSLQ&/.287 IPHDV VDPSOHFDOFXODWLRQ +] &RQYHUWWRWLPH WPHDV IPHDV V &DOFXODWHWKHGLIIHUHQFHWRWKHLGHDO SHULRGRI 'PHDV WPHDV V &DOFXODWHWKHSSPGHYLDWLRQFRPSDUHG WRWKHPHDVXUHGYDOXH (SSP î'PHDVWPHDV SSP &DOFXODWHWKHRIIVHWUHJLVWHUYDOXH 0RGH ORZSRZHU 2IIVHWYDOXH (SSP 0RGH IDVWFRUUHFWLRQ 2IIVHWYDOXH (SSP FRUUHFWLRQSXOVHV DUHQHHGHG FRUUHFWLRQSXOVHV DUHQHHGHG DDD Fig 9. PCF85063ATL Product data sheet Offset calibration calculation workflow All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 17 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus GHYLDWLRQDIWHU FRUUHFWLRQLQ 02'( SSP GHYLDWLRQDIWHU FRUUHFWLRQLQ 02'( SSP PHDVXUHGFDOFXODWHG GHYLDWLRQSSP DDD With the offset calibration an accuracy of 2 ppm (0.5 offset per LSB) can be reached (see Table 13). 1 ppm corresponds to a time deviation of 0.0864 seconds per day. (1) 3 correction pulses in MODE = 0 correspond to 13.02 ppm. (2) 4 correction pulses in MODE = 1 correspond to 16.276 ppm. (3) Reachable accuracy zone. Fig 10. Result of offset calibration 8.2.4 Register RAM_byte The PCF85063ATL provides a free RAM byte, which can be used for any purpose, for example, status byte of the system. Table 18. Bit 7 to 0 RAM_byte - 8-bit RAM register (address 03h) bit description Symbol Value Description B[7:0] 00000000[1] to RAM content 11111111 [1] Default value. 8.3 Time and date registers Most of the registers are coded in the BCD format to simplify application use. 8.3.1 Register Seconds Table 19. Seconds - seconds register (address 04h) bit description Bit Symbol 7 OS 6 to 4 [1] PCF85063ATL Product data sheet Place value Description oscillator stop SECONDS 3 to 0 Value 0 - clock integrity is guaranteed 1[1] - clock integrity is not guaranteed; oscillator has stopped or has been interrupted 0[1] to 5 ten’s place 0[1] to 9 unit place actual seconds coded in BCD format, see Table 20 Default value. All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 18 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus Table 20. Seconds coded in BCD format Seconds value in decimal Digit (unit place) Bit 6 Bit 3 Bit 5 Bit 4 Bit 2 Bit 1 Bit 0 00[1] 0 0 0 0 0 0 0 01 0 0 0 0 0 0 1 02 0 0 0 0 0 1 0 : : : : : : : : 09 0 0 0 1 0 0 1 10 0 0 1 0 0 0 0 : : : : : : : : 58 1 0 1 1 0 0 0 59 1 0 1 1 0 0 1 [1] 8.3.1.1 Upper-digit (ten’s place) Default value. OS: Oscillator stop When the oscillator of the PCF85063ATL is stopped, the OS flag is set. The oscillator can be stopped, for example, by connecting one of the oscillator pins OSCI or OSCO to ground. The oscillator is considered to be stopped during the time between power-on and stable crystal resonance. This time can be in the range of 200 ms to 2 s depending on crystal type, temperature, and supply voltage. The flag remains set until cleared by command (see Figure 11). If the flag cannot be cleared, then the oscillator is not running. This method can be used to monitor the oscillator and to determine if the supply voltage has reduced to the point where oscillation fails. 26 DQGIODJFDQQRWEHFOHDUHG 26 DQGIODJFDQEHFOHDUHG 9'' RVFLOODWLRQ 26IODJ 26IODJFOHDUHG E\VRIWZDUH RVFLOODWLRQQRZVWDEOH 26IODJVHWZKHQ RVFLOODWLRQVWRSV W DDD Fig 11. OS flag PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 19 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8.3.2 Register Minutes Table 21. Minutes - minutes register (address 05h) bit description Bit Symbol Value Place value Description 7 - 0 - unused MINUTES 0[1] ten’s place actual minutes coded in BCD format 6 to 4 [1] to 5 0[1] to 9 3 to 0 unit place Default value. 8.3.3 Register Hours Table 22. Hours - hours register (address 06h) bit description Bit Symbol Value Place value Description 7 to 6 - 00 - 12 hour mode[1] 5 AMPM 4 unused AM/PM indicator HOURS 3 to 0 24 hour mode[1] 5 to 4 HOURS 3 to 0 0[2] - AM 1 - PM 0[2] to 1 ten’s place 0[2] unit place to 9 0[2] to 2 ten’s place 0[2] unit place to 9 [1] Hour mode is set by the 12_24 bit in register Control_1. [2] Default value. actual hours in 12 hour mode coded in BCD format actual hours in 24 hour mode coded in BCD format 8.3.4 Register Days Table 23. Days - days register (address 07h) bit description Bit Symbol Value Place value Description 7 to 6 - 00 - unused 5 to 4 DAYS[1] 0[2] to 3 ten’s place actual day coded in BCD format 0[3] unit place 3 to 0 to 9 [1] If the year counter contains a value, which is exactly divisible by 4 (including the year 00), the PCF85063ATL compensates for leap years by adding a 29th day to February. [2] Default value. [3] Default value is 1. 8.3.5 Register Weekdays Table 24. PCF85063ATL Product data sheet Weekdays - weekdays register (address 08h) bit description Bit Symbol Value Description 7 to 3 - 00000 unused 2 to 0 WEEKDAYS 0 to 6 actual weekday values, see Table 25 All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 20 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus Table 25. Weekday assignments Day[1] Bit 2 1 0 Sunday 0 0 0 Monday 0 0 1 Tuesday 0 1 0 Wednesday 0 1 1 Thursday 1 0 0 Friday 1 0 1 Saturday[2] 1 1 0 [1] Definition may be reassigned by the user. [2] Default value. 8.3.6 Register Months Table 26. Months - months register (address 09h) bit description Bit Symbol Value Place value Description 7 to 5 - 000 - unused 4 MONTHS 0 to 1 ten’s place 0 to 9 unit place actual month coded in BCD format, see Table 27 3 to 0 Table 27. Month assignments in BCD format Month Product data sheet Digit (unit place) Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 January[1] 0 0 0 0 1 February 0 0 0 1 0 March 0 0 0 1 1 April 0 0 1 0 0 May 0 0 1 0 1 June 0 0 1 1 0 July 0 0 1 1 1 August 0 1 0 0 0 September 0 1 0 0 1 October 1 0 0 0 0 November 1 0 0 0 1 December 1 0 0 1 0 [1] PCF85063ATL Upper-digit (ten’s place) Default value. All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 21 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8.3.7 Register Years Table 28. Bit 7 to 4 Years - years register (0Ah) bit description Symbol Value Place value Description YEARS 0[1] to 9 ten’s place 0[1] to 9 unit place 3 to 0 [1] actual year coded in BCD format Default value. 8.4 Setting and reading the time Figure 12 shows the data flow and data dependencies starting from the 1 Hz clock tick. +]WLFN 6(&21'6 0,187(6 BKRXUPRGH /($3<($5 &$/&8/$7,21 +2856 '$<6 :((.'$< 0217+6 <($56 DDD Fig 12. Data flow for the time function During read/write operations, the time counting circuits (memory locations 04h through 0Ah) are blocked. The blocking prevents • Faulty reading of the clock and calendar during a carry condition • Incrementing the time registers during the read cycle After this read/write access is completed, the time circuit is released again and any pending request to increment the time counters that occurred during the read/write access is serviced. A maximum of 1 request can be stored; therefore, all accesses must be completed within 1 second (see Figure 13). PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 22 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus WV 67$57 6/$9($''5(66 '$7$ '$7$ 6723 DDD Fig 13. Access time for read/write operations Because of this method, it is very important to make a read or write access in one go, that is, setting or reading seconds through to years should be made in one single access. Failing to comply with this method could result in the time becoming corrupted. As an example, if the time (seconds through to hours) is set in one access and then in a second access the date is set, it is possible that the time will increment between the two accesses. A similar problem exists when reading. A roll-over may occur between reads thus giving the minutes from one moment and the hours from the next. Recommended method for reading the time: 1. Send a START condition and the slave address (see Table 39 on page 32) for write (A2h) 2. Set the address pointer to 4 (Seconds) by sending 04h 3. Send a RESTART condition or STOP followed by START 4. Send the slave address for read (A3h) 5. Read Seconds 6. Read Minutes 7. Read Hours 8. Read Days 9. Read Weekdays 10. Read Months 11. Read Years 12. Send a STOP condition PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 23 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8.5 Alarm registers 8.5.1 Register Second_alarm Table 29. Second_alarm - second alarm register (address 0Bh) bit description Bit Symbol 7 AEN_S Value second alarm 0 6 to 4 SECOND_ALARM 3 to 0 [1] Place value Description - 1[1] - 0[1] to 5 ten’s place 0[1] to 9 unit place enabled disabled second alarm information coded in BCD format Default value. 8.5.2 Register Minute_alarm Table 30. Minute_alarm - minute alarm register (address 0Ch) bit description Bit Symbol 7 AEN_M 6 to 4 Value minute alarm MINUTE_ALARM 3 to 0 [1] Place value Description 0 - 1[1] - 0[1] to 5 ten’s place 0[1] to 9 unit place enabled disabled minute alarm information coded in BCD format Default value. 8.5.3 Register Hour_alarm Table 31. Hour_alarm - hour alarm register (address 0Dh) bit description Bit Symbol 7 AEN_H 6 Value Place value Description hour alarm - 0 - 1[1] - 0 - enabled disabled unused 12 hour mode[2] 5 AMPM 4 AM/PM indicator HOUR_ALARM 3 to 0 0[1] - AM 1 - PM 0[1] to 1 ten’s place 0[1] unit place to 9 hour alarm information in 12 hour mode coded in BCD format 24 hour mode[2] 5 to 4 HOUR_ALARM 3 to 0 PCF85063ATL Product data sheet 0[1] to 2 ten’s place 0[1] unit place to 9 [1] Default value. [2] Hour mode is set by the 12_24 bit in register Control_1. All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 hour alarm information in 24 hour mode coded in BCD format © NXP B.V. 2013. All rights reserved. 24 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8.5.4 Register Day_alarm Table 32. Day_alarm - day alarm register (address 0Eh) bit description Bit Symbol 7 AEN_D 6 5 to 4 Value day alarm 0 - enabled 1[1] - disabled - 0 - unused DAY_ALARM 0[1] to 3 ten’s place 0[1] to 9 unit place day alarm information coded in BCD format 3 to 0 [1] Place value Description Default value. 8.5.5 Register Weekday_alarm Table 33. Weekday_alarm - weekday alarm register (address 0Fh) bit description Bit Symbol 7 AEN_W 6 to 3 2 to 0 [1] Value Description weekday alarm 0 enabled 1[1] disabled - 0 WEEKDAY_ALARM 0[1] unused to 6 weekday alarm information coded in BCD format Default value. 8.5.6 Alarm function By clearing the alarm enable bit (AEN_x) of one or more of the alarm registers, the corresponding alarm condition(s) are active. When an alarm occurs, AF is set logic 1. The asserted AF can be used to generate an interrupt (INT). The AF is cleared by command. The registers at addresses 0Bh through 0Fh contain alarm information. When one or more of these registers is loaded with second, minute, hour, day or weekday, and its corresponding AEN_x is logic 0, then that information is compared with the current second, minute, hour, day, and weekday. When all enabled comparisons first match, the alarm flag (AF in register Control_2) is set logic 1. The generation of interrupts from the alarm function is controlled via bit AIE. If bit AIE is enabled, the INT pin follows the condition of bit AF. AF remains set until cleared by command. Once AF has been cleared, it will only be set again when the time increments to match the alarm condition once more. Alarm registers which have their AEN_x bit at logic 1 are ignored. PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 25 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus FKHFNQRZVLJQDO H[DPSOH $(1B6 $(1B6 6(&21'$/$50 6(&21'7,0( $(1B0 0,187($/$50 0,187(7,0( $(1B+ +285$/$50 VHWDODUPIODJ$) +2857,0( $(1B' '$<$/$50 '$<7,0( $(1B: :((.'$<$/$50 :((.'$<7,0( DDD (1) Only when all enabled alarm settings are matching. It is only on increment to a matched case that the alarm flag is set. Fig 14. Alarm function block diagram PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 26 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 8.6 Timer registers The 8-bit countdown timer at address 10h is controlled by the register Timer_mode at address 11h. 8.6.1 Register Timer_value Table 34. Bit 7 to 0 Timer_value - timer value register (address 10h) bit description Symbol Value Description T[7:0] 0h[1] countdown timer value[2] to FFh [1] Default value. [2] Countdown period in seconds: CountdownPeriod = --------------------------------------------------------------- where T is the SourceClockFrequency countdown value. T 8.6.2 Register Timer_mode Table 35. Timer_mode - timer control register (address 11h) bit description Bit Symbol Value Description 7 to 5 - 000 unused 4 to 3 TCF[1:0] 2 1 timer clock frequency 00 4.096 kHz timer source clock 01 64 Hz timer source clock 10 1 Hz timer source clock 11[1] 1⁄ Hz 60 TE timer enable 0[1] timer is disabled 1 timer is enabled TIE timer interrupt enable 0[1] 1 0 timer source clock TI_TP[2] no interrupt generated from timer interrupt generated from timer timer interrupt mode 0[1] interrupt follows timer flag 1 interrupt generates a pulse [1] Default value. [2] How the setting of TI_TP and the timer flag TF can affect the INT pulse generation is explained in Section 8.2.2.3 on page 12. 8.6.3 Timer functions The timer has four selectable source clocks allowing for countdown periods in the range from 244 s to 4 hours 15 min. For periods longer than 4 hours, the alarm function can be used. PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 27 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus Table 36. Timer clock frequency and timer durations TCF[1:0] Timer source clock frequency[1] Delay Minimum timer duration T=1 Maximum timer duration T = 255 00 4.096 kHz 244 s 62.256 ms 01 64 Hz 15.625 ms 3.984 s 10 1 Hz[2] 1s 255 s 11 1⁄ 60 60 s 4 hours 15 min Hz[2] [1] When not in use, TCF[1:0] must be set to 1⁄60 Hz for power saving. [2] Time periods can be affected by correction pulses. Remark: Note that all timings which are generated from the 32.768 kHz oscillator are based on the assumption that there is 0 ppm deviation. Deviation in oscillator frequency results in deviation in timings. This is not applicable to interface timing. The timer counts down from a software-loaded 8-bit binary value, T[7:0], in register Timer_value. Loading the counter with 0 stops the timer. Values from 1 to 255 are valid. When the counter decrements from 1, the timer flag (bit TF in register Control_2) is set and the counter automatically re-loads and starts the next timer period. FRXQWGRZQYDOXH7 [[ [[ WLPHUVRXUFHFORFN FRXQWGRZQFRXQWHU 7( 7) ,17 7 7 GXUDWLRQRIILUVWWLPHUSHULRGDIWHU HQDEOHPD\UDQJHIURP7WR7 DDD In this example, it is assumed that the timer flag is cleared before the next countdown period expires and that the pin INT is set to pulsed mode. Fig 15. General countdown timer behavior If a new value of T is written before the end of the current timer period, then this value takes immediate effect. NXP does not recommend changing T without first disabling the counter by setting bit TE logic 0. The update of T is asynchronous to the timer clock. Therefore changing it without setting bit TE logic 0 may result in a corrupted value loaded into the countdown counter. This results in an undetermined countdown period for the first period. The countdown value T will, however, be correctly stored and correctly loaded on subsequent timer periods. PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 28 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus When the TIE flag is set, an interrupt signal on INT is generated if this mode is enabled. See Section 8.2.2 for details on how the interrupt can be controlled. When starting the timer for the first time, the first period has an uncertainty. The uncertainty is a result of the enable instruction being generated from the interface clock which is asynchronous from the timer source clock. Subsequent timer periods do not have such delay. The amount of delay for the first timer period depends on the chosen source clock, see Table 37. Table 37. First period delay for timer counter value T Timer source clock Minimum timer period Maximum timer period 4.096 kHz T T+1 64 Hz T T+1 1 Hz 1 T – 1 + ------------64 Hz 1 T + ------------64 Hz 1⁄ 60 1 T – 1 + ------------64 Hz 1 T + ------------64 Hz Hz At the end of every countdown, the timer sets the countdown timer flag (bit TF in register Control_2). Bit TF can only be cleared by command. The asserted bit TF can be used to generate an interrupt at pin INT. The interrupt may be generated as a pulsed signal every countdown period or as a permanently active signal which follows the condition of bit TF. Bit TI_TP is used to control this mode selection and the interrupt output may be disabled with bit TIE, see Table 35 and Figure 15. When reading the timer, the current countdown value is returned and not the initial value T. Since it is not possible to freeze the countdown timer counter during read back, it is recommended to read the register twice and check for consistent results. Timer source clock frequency selection of 1 Hz and 1⁄60 Hz is affected by the Offset register. The duration of a program period varies according to when the offset is initiated. For example, if a 100 s timer is set using the 1 Hz clock as source, then some 100 s periods will contain correction pulses and therefore be longer or shorter depending on the setting of the Offset register. See Section 8.2.3 to understand the operation of the Offset register. 8.6.3.1 Countdown timer interrupts The pulse generator for the countdown timer interrupt uses an internal clock and is dependent on the selected source clock for the countdown timer and on the countdown value T. As a consequence, the width of the interrupt pulse varies (see Table 38). Table 38. INT operation TF and INT become active simultaneously. Source clock (Hz) T = 1[1] T > 1[1] 4096 1⁄ 8192 1⁄ 4096 64 1⁄ 128 1⁄ 64 1 1⁄ 64 1⁄ 64 1⁄ 60 1⁄ 64 1⁄ 64 [1] PCF85063ATL Product data sheet INT period (s) T = loaded countdown value. Timer stops when T = 0. All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 29 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 9. Characteristics of the I2C-bus interface The I2C-bus is for bidirectional, two-line communication between different ICs or modules. The two lines are a Serial DAta line (SDA) and a Serial CLock line (SCL). Both lines must be connected to a positive supply via a pull-up resistor. Data transfer may be initiated only when the bus is not busy. 9.1 Bit transfer One data bit is transferred during each clock pulse. The data on the SDA line must remain stable during the HIGH period of the clock pulse, as changes in the data line at this time are interpreted as a control signal (see Figure 16). SDA SCL data line stable; data valid change of data allowed mbc621 Fig 16. Bit transfer 9.2 START and STOP conditions Both data and clock lines remain HIGH when the bus is not busy. A HIGH-to-LOW transition of the data line while the clock is HIGH is defined as the START condition - S. A LOW-to-HIGH transition of the data line while the clock is HIGH is defined as the STOP condition - P (see Figure 17). SDA SDA SCL SCL S P START condition STOP condition mbc622 Fig 17. Definition of START and STOP conditions 9.3 System configuration A device generating a message is a transmitter; a device receiving a message is a receiver. The device that controls the message is the master; and the devices which are controlled by the master are the slaves (see Figure 18). PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 30 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus MASTER TRANSMITTER/ RECEIVER SLAVE TRANSMITTER/ RECEIVER SLAVE RECEIVER MASTER TRANSMITTER/ RECEIVER MASTER TRANSMITTER SDA SCL mga807 Fig 18. System configuration 9.4 Acknowledge The number of data bytes transferred between the START and STOP conditions from transmitter to receiver is unlimited. Each byte of 8 bits is followed by an acknowledge cycle. • A slave receiver, which is addressed, must generate an acknowledge after the reception of each byte • Also a master receiver must generate an acknowledge after the reception of each byte that has been clocked out of the slave transmitter • The device that acknowledges must pull-down the SDA line during the acknowledge clock pulse, so that the SDA line is stable LOW during the HIGH period of the acknowledge related clock pulse (set-up and hold times must be considered) • A master receiver must signal an end of data to the transmitter by not generating an acknowledge on the last byte that has been clocked out of the slave. In this event, the transmitter must leave the data line HIGH to enable the master to generate a STOP condition Acknowledgement on the I2C-bus is shown in Figure 19. data output by transmitter not acknowledge data output by receiver acknowledge SCL from master 1 2 8 9 S START condition clock pulse for acknowledgement mbc602 Fig 19. Acknowledgement on the I2C-bus PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 31 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 9.5 I2C-bus protocol 9.5.1 Addressing One I2C-bus slave address (1010001) is reserved for the PCF85063ATL. The entire I2C-bus slave address byte is shown in Table 39. Table 39. I2C slave address byte Slave address Bit 7 6 5 4 3 2 1 MSB 0 LSB 1 0 1 0 0 0 1 R/W After a START condition, the I2C slave address has to be sent to the PCF85063ATL device. The R/W bit defines the direction of the following single or multiple byte data transfer (R/W = 0 for writing, R/W = 1 for reading). For the format and the timing of the START condition (S), the STOP condition (P) and the acknowledge bit (A) refer to the I2C-bus characteristics (see Ref. 12 “UM10204”). In the write mode, a data transfer is terminated by sending either the STOP condition or the START condition of the next data transfer. 9.5.2 Clock and calendar READ or WRITE cycles The I2C-bus configuration for the different PCF85063ATL READ and WRITE cycles is shown in Figure 20 and Figure 21. The register address is a 5-bit value that defines which register is to be accessed next. The upper 3 bits of the register address are not used. DFNQRZOHGJH IURP3&)$7/ 6 VODYHDGGUHVV ZULWHELW DFNQRZOHGJH IURP3&)$7/ DFNQRZOHGJH IURP3&)$7/ $ $ $ UHJLVWHUDGGUHVV KWRK WRQ GDWDE\WHV 36 67$57 6723 DDD Fig 20. Master transmits to slave receiver (WRITE mode) PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 32 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus DFNQRZOHGJH IURP3&)$7/ 6 VODYHDGGUHVV DFNQRZOHGJH IURP3&)$7/ $ ZULWHELW $ UHJLVWHUDGGUHVV KWRK DFNQRZOHGJH IURP3&)$7/ 6 VODYHDGGUHVV UHDGELW $ '$7$%<7( VHWUHJLVWHU DGGUHVV 3 6723 DFNQRZOHGJH IURPPDVWHU QRDFNQRZOHGJH $ $ /$67'$7$%<7( UHDGUHJLVWHU GDWD 3 WRQGDWDE\WHV DXWRLQFUHPHQW PHPRU\UHJLVWHUDGGUHVV DXWRLQFUHPHQW PHPRU\UHJLVWHUDGGUHVV DDD For multimaster configurations and to fasten the communication, the STOP-START sequence can be replaced by a repeated START (Sr). Fig 21. Master reads after setting register address (write register address; READ data) PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 33 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 10. Internal circuitry 3&)$7/ 9'' 26&, &/.287 26&2 &/.2( 6&/ ,17 6'$ 966 DDD Fig 22. Device diode protection diagram of PCF85063ATL 11. Limiting values Table 40. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter Min Max Unit VDD supply voltage 0.5 +6.5 V IDD supply current 50 +50 mA VI input voltage 0.5 +6.5 V VO output voltage 0.5 +6.5 V input current at any input 10 +10 mA IO output current at any output 10 +10 mA Ptot total power dissipation - 300 mW HBM [1] - 5000 V CDM [2] - 1750 V latch-up current [3] - 200 mA Tstg storage temperature [4] 65 +150 C Tamb ambient temperature 40 +85 C Ilu Product data sheet on pins SCL, SDA, OSCI II VESD PCF85063ATL Conditions electrostatic discharge voltage operating device [1] Pass level; Human Body Model (HBM) according to Ref. 7 “JESD22-A114”. [2] Pass level; Charged-Device Model (CDM), according to Ref. 8 “JESD22-C101”. [3] Pass level; latch-up testing, according to Ref. 9 “JESD78” at maximum ambient temperature (Tamb(max)). [4] According to the store and transport requirements (see Ref. 13 “UM10569”) the devices have to be stored at a temperature of +8 C to +45 C and a humidity of 25 % to 75 %. All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 34 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 12. Characteristics Table 41. Static characteristics VDD = 0.9 V to 5.5 V; VSS = 0 V; Tamb = 40 C to +85 C; fosc = 32.768 kHz; quartz Rs = 60 k; CL = 7 pF; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit supply voltage interface inactive; fSCL = 0 Hz [1] 0.9 - 5.5 V interface active; fSCL = 400 kHz [1] 1.8 - 5.5 V CLKOUT disabled; VDD = 3.3 V [2] - 220 450 nA - 250 500 nA Tamb = 85 C - 470 600 nA interface active; fSCL = 400 kHz - 18 50 A VSS - 5.5 V Supplies VDD IDD supply current interface inactive; fSCL = 0 Hz Tamb = 25 C Tamb = 50 C [3] Inputs[4] VI input voltage VIL LOW-level input voltage VSS - 0.3VDD V VIH HIGH-level input voltage 0.7VDD - VDD V ILI input leakage current - 0 - A 0.15 - +0.15 A - - 7 pF VI = VSS or VDD post ESD event Ci [5] input capacitance Outputs VOH HIGH-level output voltage on pin CLKOUT 0.8VDD - VDD V VOL LOW-level output voltage on pins SDA, INT, CLKOUT VSS - 0.2VDD V IOH HIGH-level output current output source current; VOH = 2.9 V; VDD = 3.3 V; on pin CLKOUT 1 3 - mA IOL LOW-level output current output sink current; VOL = 0.4 V; VDD = 3.3 V on pin SDA 3 8.5 - mA on pin INT 2 6 - mA on pin CLKOUT 1 3 - mA PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 35 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus Table 41. Static characteristics …continued VDD = 0.9 V to 5.5 V; VSS = 0 V; Tamb = 40 C to +85 C; fosc = 32.768 kHz; quartz Rs = 60 k; CL = 7 pF; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit fosc/fosc relative oscillator frequency variation VDD = 200 mV; Tamb = 25 C - 0.075 - ppm CL(itg) integrated load capacitance on pins OSCO, OSCI CL = 7 pF 4.2 7 9.8 pF CL = 12.5 pF 7.5 12.5 17.5 pF - - 100 k Oscillator [6] series resistance Rs [1] For reliable oscillator start-up at power-on: VDD(po)min = VDD(min) + 0.3 V. [2] Timer source clock = 1⁄60 Hz, level of pins SCL and SDA is VDD or VSS. [3] Tested on sample basis. [4] The I2C-bus interface of PCF85063ATL is 5 V tolerant. [5] Implicit by design. [6] OSCI OSCO Integrated load capacitance, CL(itg), is a calculation of COSCI and COSCO in series: C L itg = -------------------------------------------. C OSCI + C OSCO C ,'' $ C DDD I6&/N+] Tamb = 25 C; CLKOUT disabled. (1) VDD = 5.0 V. (2) VDD = 3.3 V. Fig 23. Typical IDD with respect to fSCL PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 36 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus DDD ,'' Q$ 7HPSHUDWXUH& CL(itg) = 7 pF; CLKOUT disabled. (1) VDD = 5.5 V. (2) VDD = 3.3 V. DDD ,'' Q$ 7HPSHUDWXUH& CL(itg) = 12.5 pF; CLKOUT disabled. (1) VDD = 5.5 V. (2) VDD = 3.3 V. Fig 24. Typical IDD as a function of temperature PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 37 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus ,'' $ DDD 9''9 Tamb = 25 C; fCLKOUT = 32768 Hz. (1) 47 pF CLKOUT load. (2) 22 pF CLKOUT load. DDD ,'' Q$ 9''9 Tamb = 25 C; CLKOUT disabled. (1) CL(itg) = 12.5 pF. (2) CL(itg) = 7 pF. Fig 25. Typical IDD with respect to VDD PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 38 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus DDD ,'' Q$ 56N VDD = 3.3 V; CLKOUT disabled. (1) CL(itg) = 12.5 pF; 50 C; maximum value. (2) CL(itg) = 7 pF; 50 C; maximum value. (3) CL(itg) = 12.5 pF; 25 C; typical value. (4) CL(itg) = 7 pF; 25 C; typical value. Fig 26. IDD with respect to quartz RS ǻIRVF SSP DDD 9''9 Tamb = 25 C. (1) CL(itg) = 7 pF. (2) CL(itg) = 12.5 pF. Fig 27. Oscillator frequency variation with respect to VDD PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 39 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus Table 42. I2C-bus characteristics VDD = 1.8 V to 5.5 V; VSS = 0 V; Tamb = 40 C to +85 C; fosc = 32.768 kHz; quartz Rs = 60 k; CL = 7 pF; unless otherwise specified. All timing values are valid within the operating supply voltage and temperature range and referenced to VIL and VIH with an input voltage swing of VSS to VDD[1]. Symbol Parameter Conditions Cb capacitive load for each bus line [2] Min Typ Max Unit - - 400 pF 0 - 400 kHz fSCL SCL clock frequency tHD;STA hold time (repeated) START condition 0.6 - - s tSU;STA set-up time for a repeated START condition 0.6 - - s tLOW LOW period of the SCL clock 1.3 - - s tHIGH HIGH period of the SCL clock 0.6 - - s tr rise time of both SDA and SCL signals 20 + 0.1Cb - 0.3 s tf fall time of both SDA and SCL signals 20 + 0.1Cb - 0.3 s tBUF bus free time between a STOP and START condition 1.3 - - s tSU;DAT data set-up time 100 - - ns tHD;DAT data hold time 0 - - ns tSU;STO set-up time for STOP condition 0.6 - - s tVD;DAT data valid time 0 - 0.9 s tVD;ACK data valid acknowledge time 0 - 0.9 s tSP pulse width of spikes that must be suppressed by the input filter 0 - 50 ns [1] A detailed description of the I2C-bus specification is given in Ref. 12 “UM10204”. [2] I2C-bus access time between two STARTs or between a START and a STOP condition to this device must be less than one second. protocol bit 7 MSB (A7) START condition (S) tSU;STA tLOW bit 6 (A6) tHIGH 1/f bit 0 (R/W) acknowledge (A) STOP condition (P) SCL SCL tBUF tr tf SDA tHD;STA tSU;DAT tHD;DAT tVD;DAT tVD;ACK tSU;STO 013aaa417 Fig 28. I2C-bus timing diagram; rise and fall times refer to 30 % and 70 % PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 40 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 13. Application information 9'' 5 6'$ 6&/ ) 0$67(5 75$160,77(5 5(&(,9(5 Q) 9'' &/.2( &/.287 ,17 6&/ 26&, 26&2 9'' 3&)$7/ 6'$ 5 966 5 5SXOOXSUHVLVWRU 5 6'$ 6&/ ,&EXV WU &E DDD A 1 farad super capacitor combined with a low VF diode can be used as a standby or back-up supply. With the RTC in its minimum power configuration that is, timer off and CLKOUT off, the RTC may operate for weeks. (1) If the clock signal (pin CLKOUT) is required in power-down mode, pin CLKOE has to be connected to the cathode side of the diode. (2) R1 limits the inrush current to the super capacitor at power-on. Fig 29. Application diagram for PCF85063ATL PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 41 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 14. Package outline DFN2626-10: plastic thermal enhanced extremely thin small outline package; no leads; 10 terminals; body 2.6 x 2.6 x 0.5 mm SOT1197-1 X A B D A E A1 A3 terminal 1 index area detail X e1 terminal 1 index area e 1 5 C C A B C v w b y y1 C L k Eh 6 10 Dh 0 1 Dimensions Unit(1) max nom min mm 2 mm scale A A1 0.5 0.05 A3 b 0.30 0.127 0.25 0.00 0.20 D Dh E Eh e e1 2.7 2.6 2.5 2.20 2.15 2.10 2.7 2.6 2.5 1.30 1.25 1.20 0.5 2 k L v 0.1 0.2 0.40 0.35 0.30 w y y1 0.05 0.05 0.05 Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. References Outline version IEC JEDEC JEITA SOT1197-1 --- --- --- sot1197-1_po European projection Issue date 11-01-20 12-09-16 Fig 30. Package outline SOT1197-1 (HXSON10) of PCF85063ATL PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 42 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 15. Handling information All input and output pins are protected against ElectroStatic Discharge (ESD) under normal handling. When handling Metal-Oxide Semiconductor (MOS) devices ensure that all normal precautions are taken as described in JESD625-A, IEC 61340-5 or equivalent standards. 16. Packing information 16.1 Tape and reel information 7239,(: ' 3 : SLQ % 3 $ ' . GLUHFWLRQRIIHHG 2ULJLQDOGLPHQVLRQVDUHLQPP )LJXUHQRWGUDZQWRVFDOH DDD Fig 31. Tape and reel details for PCF85063ATL Table 43. Carrier tape dimensions of PCF85063ATL Nominal values without production tolerances. Symbol Description Value Unit A0 pocket width in x direction 2.9 mm B0 pocket width in y direction 2.9 mm K0 pocket depth 0.8 mm P1 pocket hole pitch 4 mm D1 pocket hole diameter 1 mm Compartments Overall dimensions PCF85063ATL Product data sheet W tape width 8 mm D0 sprocket hole diameter 1.5 mm P0 sprocket hole pitch 4 mm All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 43 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 17. Soldering of SMD packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 “Surface mount reflow soldering description”. 17.1 Introduction to soldering Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both the mechanical and the electrical connection. There is no single soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization. 17.2 Wave and reflow soldering Wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. The wave soldering process is suitable for the following: • Through-hole components • Leaded or leadless SMDs, which are glued to the surface of the printed circuit board Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. Leaded packages, packages with solder balls, and leadless packages are all reflow solderable. Key characteristics in both wave and reflow soldering are: • • • • • • Board specifications, including the board finish, solder masks and vias Package footprints, including solder thieves and orientation The moisture sensitivity level of the packages Package placement Inspection and repair Lead-free soldering versus SnPb soldering 17.3 Wave soldering Key characteristics in wave soldering are: • Process issues, such as application of adhesive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave • Solder bath specifications, including temperature and impurities PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 44 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 17.4 Reflow soldering Key characteristics in reflow soldering are: • Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 32) than a SnPb process, thus reducing the process window • Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board • Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 44 and 45 Table 44. SnPb eutectic process (from J-STD-020D) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 < 2.5 235 220 2.5 220 220 Table 45. Lead-free process (from J-STD-020D) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 to 2000 > 2000 < 1.6 260 260 260 1.6 to 2.5 260 250 245 > 2.5 250 245 245 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 32. PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 45 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus temperature maximum peak temperature = MSL limit, damage level minimum peak temperature = minimum soldering temperature peak temperature time 001aac844 MSL: Moisture Sensitivity Level Fig 32. Temperature profiles for large and small components For further information on temperature profiles, refer to Application Note AN10365 “Surface mount reflow soldering description”. PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 46 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 18. Footprint information Footprint information for reflow soldering of DFN2626-10 package SOT1197-1 Hx Gx D P 0.025 0.025 Ay Gy By SPy SLy nSPy Hy nSPx SPx SLx Generic footprint pattern Refer to the package outline drawing for actual layout solder land solder paste deposit solder land plus solder paste occupied area solder resist DIMENSIONS in mm P Ay By D SLx SLy SPx SPy Gx Gy Hx Hy 0.5 3.05 1.9 0.25 2.2 1.3 0.8 0.4 2.5 2.85 2.85 3.3 Issue date 11-07-27 12-09-16 sot1197-1_fr Fig 33. Footprint information for reflow soldering of SOT1197-1 (HXSON10) of PCF85063ATL PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 47 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 19. Abbreviations Table 46. PCF85063ATL Product data sheet Abbreviations Acronym Description BCD Binary Coded Decimal CMOS Complementary Metal Oxide Semiconductor ESD ElectroStatic Discharge HBM Human Body Model I2C Inter-Integrated Circuit IC Integrated Circuit LSB Least Significant Bit MSB Most Significant Bit MSL Moisture Sensitivity Level PCB Printed-Circuit Board POR Power-On Reset RTC Real-Time Clock SCL Serial CLock line SDA Serial DAta line SMD Surface Mount Device All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 48 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 20. References [1] AN10365 — Surface mount reflow soldering description [2] AN10366 — HVQFN application information [3] AN11247 — Improved timekeeping accuracy with PCF85063, PCF8523 and PCF2123 using an external temperature sensor [4] IEC 60134 — Rating systems for electronic tubes and valves and analogous semiconductor devices [5] IEC 61340-5 — Protection of electronic devices from electrostatic phenomena [6] IPC/JEDEC J-STD-020 — Moisture/Reflow Sensitivity Classification for Nonhermetic Solid State Surface Mount Devices [7] JESD22-A114 — Electrostatic Discharge (ESD) Sensitivity Testing Human Body Model (HBM) [8] JESD22-C101 — Field-Induced Charged-Device Model Test Method for Electrostatic-Discharge-Withstand Thresholds of Microelectronic Components [9] JESD78 — IC Latch-Up Test [10] JESD625-A — Requirements for Handling Electrostatic-Discharge-Sensitive (ESDS) Devices [11] SNV-FA-01-02 — Marking Formats Integrated Circuits [12] UM10204 — I2C-bus specification and user manual [13] UM10569 — Store and transport requirements 21. Revision history Table 47. Revision history Document ID Release date Data sheet status Change notice Supersedes PCF85063ATL v.2 20130415 Product data sheet - PCF85063ATL v.1 - - Modifications: PCF85063ATL v.1 PCF85063ATL Product data sheet • • Adjusted IDD and ILI values (Table 41) Updated Figure 22 20130225 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 49 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 22. Legal information 22.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 22.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 22.3 Disclaimers Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. PCF85063ATL Product data sheet Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 50 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Non-automotive qualified products — Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors’ warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ standard warranty and NXP Semiconductors’ product specifications. Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. 22.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. I2C-bus — logo is a trademark of NXP B.V. 23. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 51 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 24. Tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Table 18. Table 19. Table 20. Table 21. Table 22. Table 23. Table 24. Table 25. Table 26. Table 27. Table 28. Table 29. Table 30. Table 31. Table 32. Table 33. Table 34. Table 35. Table 36. Ordering information . . . . . . . . . . . . . . . . . . . . .2 Ordering options . . . . . . . . . . . . . . . . . . . . . . . . .2 Marking codes . . . . . . . . . . . . . . . . . . . . . . . . . .2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . .3 Registers overview . . . . . . . . . . . . . . . . . . . . . .5 Control_1 - control and status register 1 (address 00h) bit description . . . . . . . . . . . . . . .6 First increment of time circuits after STOP bit release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Registers reset values . . . . . . . . . . . . . . . . . . . .9 Control_2 - control and status register 2 (address 01h) bit description . . . . . . . . . . . . . .10 Effect of bits MI and HMI on INT generation . .12 CLKOUT frequency selection . . . . . . . . . . . . .13 Offset - offset register (address 02h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Offset values . . . . . . . . . . . . . . . . . . . . . . . . . .14 Correction pulses for MODE = 0 . . . . . . . . . . .15 Effect of correction pulses on frequencies for MODE = 0. . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Correction pulses for MODE = 1 . . . . . . . . . . .16 Effect of correction pulses on frequencies for MODE = 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 RAM_byte - 8-bit RAM register (address 03h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . .18 Seconds - seconds register (address 04h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Seconds coded in BCD format . . . . . . . . . . . .19 Minutes - minutes register (address 05h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Hours - hours register (address 06h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Days - days register (address 07h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Weekdays - weekdays register (address 08h) bit description . . . . . . . . . . . . . . . . . . . . . . . . .20 Weekday assignments . . . . . . . . . . . . . . . . . . .21 Months - months register (address 09h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Month assignments in BCD format . . . . . . . . . .21 Years - years register (0Ah) bit description. . . .22 Second_alarm - second alarm register (address 0Bh) bit description . . . . . . . . . . . . . .24 Minute_alarm - minute alarm register (address 0Ch) bit description . . . . . . . . . . . . . .24 Hour_alarm - hour alarm register (address 0Dh) bit description. . . . . . . . . . . . . . . . . . . . . .24 Day_alarm - day alarm register (address 0Eh) bit description . . . . . . . . . . . . . . . . . . . . . .25 Weekday_alarm - weekday alarm register (address 0Fh) bit description . . . . . . . . . . . . . .25 Timer_value - timer value register (address 10h) bit description . . . . . . . . . . . . . . . . . . . . .27 Timer_mode - timer control register (address 11h) bit description . . . . . . . . . . . . . . . . . . . . . .27 Timer clock frequency and timer durations. . . .28 PCF85063ATL Product data sheet Table 37. Table 38. Table 39. Table 40. Table 41. Table 42. Table 43. Table 44. Table 45. Table 46. Table 47. First period delay for timer counter value T . . 29 INT operation . . . . . . . . . . . . . . . . . . . . . . . . . . 29 I2C slave address byte . . . . . . . . . . . . . . . . . . . 32 Limiting values . . . . . . . . . . . . . . . . . . . . . . . . 34 Static characteristics . . . . . . . . . . . . . . . . . . . . 35 I2C-bus characteristics . . . . . . . . . . . . . . . . . . . 40 Carrier tape dimensions of PCF85063ATL . . . 43 SnPb eutectic process (from J-STD-020D) . . . 45 Lead-free process (from J-STD-020D) . . . . . . 45 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . 48 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 49 All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 52 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 25. Figures Fig 1. Fig 2. Fig 3. Fig 4. Fig 5. Fig 6. Fig 7. Fig 8. Fig 9. Fig 10. Fig 11. Fig 12. Fig 13. Fig 14. Fig 15. Fig 16. Fig 17. Fig 18. Fig 19. Fig 20. Fig 21. Fig 22. Fig 23. Fig 24. Fig 25. Fig 26. Fig 27. Fig 28. Fig 29. Fig 30. Fig 31. Fig 32. Fig 33. Block diagram of PCF85063ATL . . . . . . . . . . . . . .2 Pin configuration for HXSON10 (PCF85063ATL) .3 Handling address registers . . . . . . . . . . . . . . . . . .4 STOP bit functional diagram . . . . . . . . . . . . . . . . .7 STOP bit release timing . . . . . . . . . . . . . . . . . . . . .8 Software reset command . . . . . . . . . . . . . . . . . . . .9 Interrupt scheme . . . . . . . . . . . . . . . . . . . . . . . . . 11 INT example for MI . . . . . . . . . . . . . . . . . . . . . . .12 Offset calibration calculation workflow . . . . . . . . .17 Result of offset calibration . . . . . . . . . . . . . . . . . .18 OS flag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Data flow for the time function . . . . . . . . . . . . . . .22 Access time for read/write operations . . . . . . . . .23 Alarm function block diagram. . . . . . . . . . . . . . . .26 General countdown timer behavior . . . . . . . . . . .28 Bit transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Definition of START and STOP conditions. . . . . .30 System configuration . . . . . . . . . . . . . . . . . . . . . .31 Acknowledgement on the I2C-bus . . . . . . . . . . . .31 Master transmits to slave receiver (WRITE mode). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Master reads after setting register address (write register address; READ data) . . . . . . . . . .33 Device diode protection diagram of PCF85063ATL . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Typical IDD with respect to fSCL . . . . . . . . . . . . . .36 Typical IDD as a function of temperature . . . . . . .37 Typical IDD with respect to VDD . . . . . . . . . . . . . .38 IDD with respect to quartz RS . . . . . . . . . . . . . . . .39 Oscillator frequency variation with respect to VDD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 I2C-bus timing diagram; rise and fall times refer to 30 % and 70 % . . . . . . . . . . . . . . . . . . . . . . . .40 Application diagram for PCF85063ATL . . . . . . . .41 Package outline SOT1197-1 (HXSON10) of PCF85063ATL . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Tape and reel details for PCF85063ATL . . . . . . .43 Temperature profiles for large and small components . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 Footprint information for reflow soldering of SOT1197-1 (HXSON10) of PCF85063ATL . . . . .47 PCF85063ATL Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 2 — 15 April 2013 © NXP B.V. 2013. All rights reserved. 53 of 54 PCF85063ATL NXP Semiconductors Tiny Real-Time Clock/calendar with alarm function and I2C-bus 26. Contents 1 2 3 4 4.1 5 6 7 7.1 7.2 8 8.1 8.2 8.2.1 8.2.1.1 8.2.1.2 8.2.1.3 8.2.2 8.2.2.1 8.2.2.2 8.2.2.3 8.2.2.4 8.2.3 8.2.3.1 8.2.3.2 8.2.3.3 8.2.4 8.3 8.3.1 8.3.1.1 8.3.2 8.3.3 8.3.4 8.3.5 8.3.6 8.3.7 8.4 8.5 8.5.1 8.5.2 8.5.3 8.5.4 8.5.5 8.5.6 8.6 8.6.1 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 2 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional description . . . . . . . . . . . . . . . . . . . 4 Registers organization . . . . . . . . . . . . . . . . . . . 5 Control registers . . . . . . . . . . . . . . . . . . . . . . . . 6 Register Control_1 . . . . . . . . . . . . . . . . . . . . . . 6 EXT_TEST: external clock test mode . . . . . . . . 6 STOP: STOP bit function . . . . . . . . . . . . . . . . . 7 Software reset. . . . . . . . . . . . . . . . . . . . . . . . . . 9 Register Control_2 . . . . . . . . . . . . . . . . . . . . . 10 Alarm interrupt . . . . . . . . . . . . . . . . . . . . . . . . 11 MI and HMI: minute and half minute interrupt. 11 TF: timer flag . . . . . . . . . . . . . . . . . . . . . . . . . 12 COF[2:0]: Clock output frequency . . . . . . . . . 12 Register Offset . . . . . . . . . . . . . . . . . . . . . . . . 13 Correction when MODE = 0 . . . . . . . . . . . . . . 15 Correction when MODE = 1 . . . . . . . . . . . . . . 16 Offset calibration workflow . . . . . . . . . . . . . . . 17 Register RAM_byte . . . . . . . . . . . . . . . . . . . . 18 Time and date registers . . . . . . . . . . . . . . . . . 18 Register Seconds . . . . . . . . . . . . . . . . . . . . . . 18 OS: Oscillator stop . . . . . . . . . . . . . . . . . . . . . 19 Register Minutes. . . . . . . . . . . . . . . . . . . . . . . 20 Register Hours . . . . . . . . . . . . . . . . . . . . . . . . 20 Register Days . . . . . . . . . . . . . . . . . . . . . . . . . 20 Register Weekdays. . . . . . . . . . . . . . . . . . . . . 20 Register Months . . . . . . . . . . . . . . . . . . . . . . . 21 Register Years . . . . . . . . . . . . . . . . . . . . . . . . 22 Setting and reading the time. . . . . . . . . . . . . . 22 Alarm registers . . . . . . . . . . . . . . . . . . . . . . . . 24 Register Second_alarm . . . . . . . . . . . . . . . . . 24 Register Minute_alarm . . . . . . . . . . . . . . . . . . 24 Register Hour_alarm . . . . . . . . . . . . . . . . . . . 24 Register Day_alarm . . . . . . . . . . . . . . . . . . . . 25 Register Weekday_alarm . . . . . . . . . . . . . . . . 25 Alarm function. . . . . . . . . . . . . . . . . . . . . . . . . 25 Timer registers . . . . . . . . . . . . . . . . . . . . . . . . 27 Register Timer_value . . . . . . . . . . . . . . . . . . . 27 8.6.2 8.6.3 8.6.3.1 9 9.1 9.2 9.3 9.4 9.5 9.5.1 9.5.2 10 11 12 13 14 15 16 16.1 17 17.1 17.2 17.3 17.4 18 19 20 21 22 22.1 22.2 22.3 22.4 23 24 25 26 Register Timer_mode. . . . . . . . . . . . . . . . . . . Timer functions. . . . . . . . . . . . . . . . . . . . . . . . Countdown timer interrupts . . . . . . . . . . . . . . Characteristics of the I2C-bus interface . . . . Bit transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . START and STOP conditions. . . . . . . . . . . . . System configuration . . . . . . . . . . . . . . . . . . . Acknowledge . . . . . . . . . . . . . . . . . . . . . . . . . I2C-bus protocol . . . . . . . . . . . . . . . . . . . . . . . Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . Clock and calendar READ or WRITE cycles . Internal circuitry . . . . . . . . . . . . . . . . . . . . . . . Limiting values . . . . . . . . . . . . . . . . . . . . . . . . Characteristics . . . . . . . . . . . . . . . . . . . . . . . . Application information . . . . . . . . . . . . . . . . . Package outline. . . . . . . . . . . . . . . . . . . . . . . . Handling information . . . . . . . . . . . . . . . . . . . Packing information . . . . . . . . . . . . . . . . . . . . Tape and reel information . . . . . . . . . . . . . . . Soldering of SMD packages . . . . . . . . . . . . . . Introduction to soldering. . . . . . . . . . . . . . . . . Wave and reflow soldering. . . . . . . . . . . . . . . Wave soldering . . . . . . . . . . . . . . . . . . . . . . . Reflow soldering . . . . . . . . . . . . . . . . . . . . . . Footprint information . . . . . . . . . . . . . . . . . . . Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . References. . . . . . . . . . . . . . . . . . . . . . . . . . . . Revision history . . . . . . . . . . . . . . . . . . . . . . . Legal information . . . . . . . . . . . . . . . . . . . . . . Data sheet status . . . . . . . . . . . . . . . . . . . . . . Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . Contact information . . . . . . . . . . . . . . . . . . . . Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 27 29 30 30 30 30 31 32 32 32 34 34 35 41 42 43 43 43 44 44 44 44 45 47 48 49 49 50 50 50 50 51 51 52 53 54 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2013. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] Date of release: 15 April 2013 Document identifier: PCF85063ATL