Features • • • • • • • • • • • • • • • • • • • • • 8032 Pin and Instruction Compatible Four 8-bit I/O Ports Three 16-bit Timer/Counters 256 bytes RAM Full-duplex UART Asynchronous Port Reset 6 Sources, 2 Level Interrupt Structure 64 Kbytes Program Memory Space 64 Kbytes Data Memory Space Power Control Modes Idle Mode Power-down Mode On-chip Oscillator Operating Frequency: 30 MHz Power Supply: 4.5V to 5.5V Temperature Range: Military (-55oC to 125oC) No Single Event Latch-up below a LET Threshold of 80 MeV/mg/cm 2 Tested up to a Total Dose of 30 krads (Si) according to MIL STD 883 Method 1019 Packages: Side Brazed 40-pin, MQFPJ 44-pin QML Q and V with SMD 5962-00518 SCC C an B with Specification SCC9521002 Rad. Tolerant 8-bit ROMless Microcontroller 80C32E Description The 80C32E is a radiation tolerant ROMless version of the 80C52 single chip 8-bit microcontroller. The 80C32E retains all the features of the 80C32 with 256 bytes of internal RAM, a 6source, 2-level interrupt system, an on-chip oscillator and three 16-bit timer/counters. The fully static design of the 80C32E reduces system power consumption by bringing the clock frequency down to any value, even DC, without loss of data. The 80C32E has 2 software-selectable modes of reduced activity for further reduction in power consumption. In the idle mode the CPU is frozen while the timers, the serial port and the interrupt system are still operating. In the power-down mode the RAM is saved and all other functions are inoperative. Rev. 4149M–AERO–06/04 1 P3 P2 P1 P0 TxD RxD Block Diagram XTAL1 RAM 256x8 UART XTAL2 Parallel I/O Ports & Ext. Bus Port 0 Port 1 Port 2 Port 3 ALE C51 CORE PSEN IB-bus CPU Timer 0 Timer 1 T1 INT Ctrl RD T0 EA Timer 2 T2EX T2 INT1 INT0 RST WR 13 P0.2/AD2 P0.3/AD3 P0.1/AD1 P0.0/AD0 32 P0.7/A7 P1.7 9 37 EA/VPP ALE PSEN P2.7/A15 P2.6/A14 P2.5/A13 P0.6/AD6 31 30 RST 10 36 P0.7/AD7 P3.0/RxD 35 34 EA NIC* 11 12 P3.1/TxD 13 33 ALE P3.2/INT0 P3.3/INT1 14 15 32 31 PSEN P3.4/T0 P3.5/T1 16 30 P2.6/A14 17 29 P2.5/A13 29 28 27 14 15 26 16 25 P3.7/RD XTAL2 17 18 24 23 P2.2/A10 XTAL1 19 20 22 21 P2.1/A9 Note: VCC 39 38 P0.4/AD4 P1.6 P3.4/T0 P3.5/T1 P3.6/WR VSS 2 P0.6/A6 P2.4/A12 P2.3/A11 P2.0/A8 MQFPJ44 P0.5/AD5 NIC* P2.7/A15 18 19 20 21 22 23 24 25 26 27 28 P2.3/A11 P2.4/A12 11 12 SB40 33 6 5 4 3 2 1 44 43 42 41 40 7 8 P2.2/A10 P3.2/INT0 P3.3/INT1 10 P1.5 P2.1/A9 P3.0/RxD P3.1/TxD 9 P0.5/A5 NIC* P2.0/A8 P1.7 RST P0.3/A3 P0.4/A4 VSS 7 8 36 35 34 XTAL1 P1.6 6 XTAL2 5 P0.1/A1 P0.2/A2 P3.7/RD P1.4 P1.5 37 P1.4 3 4 NIC* P0.0/A0 P1.0 VCC 39 38 P1.1 40 2 P1.2 1 P3.6/WR P1.0/T2 P1.1/T2EX P1.2 P1.3 P1.3 Pin Configuration NIC: No Internal Connection 80C32E 4149M–AERO–06/04 80C32E Pin Description Mnemonic Type Name and Function VSS I Ground: 0V reference VCC I Power Supply: This is the power supply voltage for normal, idle and power-down operation P0.0-P0.7 I/O P1.0-P1.7 I/O P2.0-P2.7 I/O I/O Port 0: Port 0 is an open-drain, bidirectional I/O port. Port 0 pins that have 1s written to them float and can be used as high impedance inputs. Port 0 pins must be polarized to Vcc or Vss in order to prevent any parasitic current consumption. Port 0 is also the multiplexed low-order address and data bus during access to external program and data memory. In this application, it uses strong internal pull-up when emitting 1s. Port 1: Port 1 is an 8-bit bidirectional I/O port with internal pull-ups. Port 1 pins that have 1s written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, Port 1 pins that are externally pulled low will source current because of the internal pull-ups. Port 2: Port 2 is an 8-bit bidirectional I/O port with internal pull-ups. Port 2 pins that have 1s written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, Port 2 pins that are externally pulled low will source current because of the internal pull-ups. Port 2 emits the high-order address byte during fetches from external program memory and during accesses to external data memory that use 16-bit addresses (MOVX @DPTR).In this application, it uses strong internal pull-ups emitting 1s. During accesses to external data memory that use 8-bit addresses (MOVX @Ri), port 2 emits the contents of the P2 SFR. Port 3: Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3 pins that have 1s written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, Port 3 pins that are externally pulled low will source current because of the internal pull-ups. Port 3 also serves the special features of the 80C51 family, as listed below. I RXD (P3.0): Serial input port O TXD (P3.1): Serial output port I INT0 (P3.2): External interrupt 0 I INT1 (P3.3): External interrupt 1 I T0 (P3.4): Timer 0 external input I T1 (P3.5): Timer 1 external input O WR (P3.6): External data memory write strobe O RD (P3.7): External data memory read strobe I Reset: A high on this pin for two machine cycles while the oscillator is running, resets the device. An internal diffused resistor to VSS permits a power-on reset using only an external capacitor to VCC. P3.0-P3.7 RST 3 4149M–AERO–06/04 Mnemonic Type Name and Function O (I) Address Latch Enable: Output pulse for latching the low byte of the address during an access to external memory. In normal operation, ALE is emitted at a constant rate of 1/6 the oscillator frequency, and can be used for external timing or clocking. Note that one ALE pulse is skipped during each access to external data memory. PSEN O Program Store ENable: The read strobe to external program memory. When executing code from the external program memory, PSEN is activated twice each machine cycle, except that two PSEN activations are skipped during each access to external data memory. PSEN is not activated during fetches from internal program memory. EA I External Access Enable: EA must be externally held low to enable the device to fetch code from external program memory locations. XTAL1 I Crystal 1: Input to the inverting oscillator amplifier and input to the internal clock generator circuits. XTAL2 O Crystal 2: Output from the inverting oscillator amplifier ALE 4 80C32E 4149M–AERO–06/04 80C32E Idle and Power-down Operation Idle mode allows the interrupt, serial port and timer blocks to continue to operate while the clock of the CPU is gated off. Power-down mode stops the oscillator. Table 1. PCON Register PCON – Power Control Register 7 6 5 4 3 2 1 0 SMOD - - - GF1 GF0 PD IDL Bit Number Bit Mnemonic 7 SMOD 6 - Reserved The value read from this bit is indeterminate. Do not set this bit. 5 - Reserved The value read from this bit is indeterminate. Do not set this bit. 4 - Reserved The value read from this bit is indeterminate. Do not set this bit. 3 GF1 General-purpose Flag Cleared by user for General-purpose usage. Set by user for General-purpose usage. 2 GF0 General-purpose Flag Cleared by user for General-purpose usage. Set by user for General-purpose usage. 1 PD Power-down mode bit Cleared by hardware when reset occurs. Set to enter power-down mode. 0 IDL Idle mode bit Clear by hardware when interrupt or reset occurs. Set to enter idle mode. Description Double Baud Rate bit Set to select double baud rate in mode 1, 2 or 3. Reset Value = 000X 0000 Not bit addressable 5 4149M–AERO–06/04 Idle Mode An instruction that sets PCON.0 causes that to be the last instruction executed before going into Idle mode. In Idle mode, the internal clock signal is gated off to the CPU, but not to the interrupt, Timer, and Serial Port functions. The CPU status is preserved in its entirety: the Stack Pointer, Program Counter, Program Status Word, Accumulator, RAM and all other registers maintain their data during Idle. The port pins hold the logical states they had at the time Idle was activated. ALE and PSEN hold at logic high levels. There are two ways to terminate the Idle. Activation of any enabled interrupt will cause PCON.0 to be cleared by hardware, terminating the Idle mode. The interrupt will be serviced, and following RETI the next instruction to be executed will be the one following the instruction that put the device into idle. The flag bits GF0 and GF1 can be used to give an indication if an interrupt occurred during normal operation or during an Idle. For example, an instruction that activates Idle can also set one or both flag bits. When Idle is terminated by an interrupt, the interrupt service routine can examine the flag bits. The other way of terminating the Idle mode is with a hardware reset. Since the clock oscillator is still running, the hardware reset needs to be held active for only two machine cycles (24 oscillator periods) to complete the reset. Power-down Mode To save maximum power, a power-down mode can be invoked by software. In power-down mode, the oscillator is stopped and the instruction that invoked powerdown mode is the last instruction executed. The internal RAM and SFRs retain their value until the power-down mode is terminated. VCC can be lowered to save further power. Either a hardware reset or an external interrupt can cause an exit from powerdown. To properly terminate power-down, the reset or external interrupt should not be executed before VCC is restored to its normal operating level and must be held active long enough for the oscillator to restart and stabilize. Only external interrupts INT0 and INT1 are useful to exit from power-down. For that, interrupt must be enabled and configured as level or edge sensitive interrupt input. Holding the pin low restarts the oscillator but bringing the pin high completes the exit as detailed in Figure 1. When both interrupts are enabled, the oscillator restarts as soon as one of the two inputs is held low and Power-down exit will be completed when the first input will be released. In this case the higher priority interrupt service routine is executed Once the interrupt is serviced, the next instruction to be executed after RETI will be the one following the instruction that put 80C32E into power-down mode. Figure 1. Power-down Exit Waveform INT0 INT1 XTAL1 Active phase Power-down phase Oscillator restart phase Active phase Exit from power-down by reset redefines all the SFRs, exit from power-down by external interrupt does no affect the SFRs. 6 80C32E 4149M–AERO–06/04 80C32E Exit from power-down by either reset or external interrupt does not affect the internal RAM content. Note: If idle mode is activated with power-down mode (IDL and PD bits set), the exit sequence is unchanged, when execution is vectored to interrupt, PD and IDL bits are cleared and idle mode is not entered. Table 2. State of Ports During Idle and Power-down Modes Mode Program Memory ALE PSEN PORT0 PORT1 PORT2 PORT3 Idle External 1 1 Floating Port Data Address Port Data Powerdown External 0 0 Floating Port Data Port Data Port Data 7 4149M–AERO–06/04 Hardware Description Refer to the C51 8-bit Microcontroller Hardware description manual for details on 80C32E functionality. Electrical Characteristics Absolute Maximum Ratings(2) Ambient Temperature Under Bias. M = Military-55°C to 125°C Storage Temperature .................................... -65°C to + 150°C Voltage on VCC to VSS ..........................................-0.5V to + 7V Voltage on Any Pin to VSS ..........................-0.5V to VCC + 0.5V Power Dissipation ........................................................... 1 W(2) 8 Notes: 1. Stresses at or above those listed under “ Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions may affect device reliability. 2. This value is based on the maximum allowable die temperature and the thermal resistance of the package. 80C32E 4149M–AERO–06/04 80C32E DC Parameters Table 3. DC Parameters in Standard VoltageTA = -55°C to +125°C; VSS = 0V; V CC = 5V ± 10%; F = 0 to 30 MHz. Symbol Parameter Min. Max Unit VIL Input Low Voltage -0.5 0.2 V CC - 0.1 V VIH Input High Voltage except XTAL1, RST 0.2 VCC + 1.4 VCC + 0.5 V VIH1 Input High Voltage, XTAL1, RST 0.7 V CC VCC + 0.5 V VOL Output Low Voltage, ports 1, 2, 3 (5) 0.45 V IOL = 1.6 mA(4) VOL1 Output Low Voltage, port 0, ALE, PSEN(5) 0.45 V IOL = 3.2 mA(4) VOH Output High Voltage, ports 1, 2, 3 2.4 0.75 VCC 0.9 V CC V V V IOH = -60 µA IOH = -25 µA IOH = -10 µA VOH1 Output High Voltage, port 0, ALE, PSEN 2.4 0.75 VCC 0.9 V CC V V V IOH = -400 µA IOH = -150 µA IOH = -40 µA RRST RST Pull-down Resistor 50 200 kΩ Test Conditions IIL Logical 0 Input Current ports 1, 2 and 3 -75 µA Vin = 0.45V ILI Input Leakage Current ±10 µA 0.45 V < Vin < VCC ITL Logical 1 to 0 Transition Current, ports 1, 2, 3 -750 µA Vin = 2.0V CIO Capacitance of I/O Buffer 10 pF Fc = 1 MHz TA = 25°C IPD Power-down Current (3) 75 µA 2.0V < VCC < 5.5V ICC Power Supply Current (1)(2)(6) Freq = 1 MHz Icc Op Freq = 1 MHz Icc Idle Freq = 6 MHz Icc Op Freq = 6 MHz Icc Idle Freq >12 MHz Icc Op Freq >12 MHz Icc Idle 1.8 1 10 4 1.25F + 5 0.36F + 2.7 mA mA mA mA mA mA Notes: VCC = 5.5V F in MHz 1. ICC under reset is measured with all output pins disconnected; XTAL1 driven with TCLCH, TCHCL = 5 ns (see Figure 6), V IL = VSS + 0.5V, VIH = V CC - 0.5V; XTAL2 N.C.; EA = RST = Port 0 = VCC. ICC would be slightly higher if a crystal oscillator is used. 2. Idle ICC is measured with all output pins disconnected; XTAL1 driven with TCLCH , TCHCL = 5 ns, V IL = VSS + 0.5V, VIH = VCC 0.5V; XTAL2 N.C; Port 0 = VCC; EA = RST = V SS (see Figure 4). 3. Power-down ICC is measured with all output pins disconnected; EA = V SS, PORT 0 = VCC; XTAL2 NC.; RST = VSS (see Figure 5). 4. Capacitance loading on Ports 0 and 2 may cause spurious noise pulses to be superimposed on the VOLs of ALE and Ports 1 and 3. The noise is due to external bus capacitance discharging into the Port 0 and Port 2 pins when these pins make 1 to 0 transitions during bus operation. In the worst cases (capacitive loading 100 pF), the noise pulse on the ALE line may exceed 0.45V with maxi VOL peak 0.6V. The use of a Schmitt Trigger is not necessary. 5. Under steady state (non-transient) conditions, IOL must be externally limited as follows: Maximum IOL per port pin: 10 mA Maximum IOL per 8-bit port: Port 0: 26 mA Ports 1, 2 and 3: 15 mA Maximum total IOL for all output pins: 71 mA 9 4149M–AERO–06/04 If IOL exceeds the test condition, V OL may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test conditions. 6. Operating ICC is measured with all output pins disconnected; XTAL1 driven with TCLCH , TCHCL = 5 ns, VIL = VSS + 0.5V, VIH = V CC - 0.5V; XTAL2 N.C.; EA = Port 0 = VCC; RST = VSS. The internal ROM runs the code 80 FE (label: SJMP label). ICC would be slightly higher if a crystal oscillator is used. Measurements are made with OTP products when possible, which is the worst case. Figure 2. ICC Test Condition, Under Reset VCC ICC VCC P0 VCC RST (NC) CLOCK SIGNAL VCC EA XTAL2 XTAL1 VSS All other pins are disconnected. Figure 3. Operating ICC Test Condition VCC ICC VCC Reset = Vss after a high pulse during at least 24 clock cycles RST (NC) CLOCK SIGNAL VCC P0 EA XTAL2 XTAL1 All other pins are disconnected. VSS Figure 4. ICC Test Condition, Idle Mode VCC ICC VCC Reset = Vss after a high pulse during at least 24 clock cycles VCC P0 RST (NC) CLOCK SIGNAL 10 XTAL2 XTAL1 VSS EA All other pins are disconnected. 80C32E 4149M–AERO–06/04 80C32E Figure 5. ICC Test Condition, Power-down Mode VCC ICC VCC Reset = Vss after a high pulse during at least 24 clock cycles P0 RST (NC) VCC EA XTAL2 XTAL1 VSS All other pins are disconnected. Figure 6. Clock Signal Waveform for ICC Tests in Active and Idle Modes VCC-0.5V 0.45V TCLCH TCHCL TCLCH = TCHCL = 5ns. 0.7VCC 0.2VCC-0.1 11 4149M–AERO–06/04 AC Parameters Each timing symbol has 5 characters. The first character is always a “T” (stands for time). The other characters, depending on their positions, stand for the name of a signal or the logical status of that signal. The following is a list of all the characters and what they stand for. Example: TAVLL = Time for Address Valid to ALE Low. TLLPL = Time for ALE Low to PSEN Low. TA = -55°C to +125°C (Military temperature range); VSS = 0V; VCC = 5V ± 10%; Load capacitance for Port 0, ALE and PSEN = 100 pF; Load capacitance for all other outputs = 80 pF. Table 4. External Program Memory Characteristics (ns) 30 MHz Symbol Parameter Min TLHLL ALE Pulse Width 60 TAVLL Address Valid to ALE 15 TLLAX Address Hold After ALE 35 TLLIV ALE to Valid Instruction In TLLPL ALE to PSEN 25 TPLPH PSEN Pulse Width 80 TPLIV PSEN to Valid Instruction In TPXIX Input Instruction Hold After PSEN TPXIZ Input Instruction Float After PSEN TPXAV PSEN to Address Valid TAVIV Address to Valid Instruction In TPLAZ PSEN Low to Address Float Max 100 65 0 30 35 130 6 Figure 7. External Program Memory Read Cycle 12 TCLCL TLHLL TLLIV ALE TLLPL TPLPH PSEN TLLAX TAVLL PORT 0 INSTR IN TPLIV TPLAZ A0-A7 TPXAV TPXIZ TPXIX INSTR IN A0-A7 INSTR IN TAVIV PORT 2 12 ADDRESS OR SFR-P2 ADDRESS A8-A15 ADDRESS A8-A15 80C32E 4149M–AERO–06/04 80C32E Table 5. External Data Memory Characteristics (ns) 30 MHz Symbol Parameter min max TRLRH RD Pulse Width 180 TWLWH WR Pulse Width 180 TRLDV RD to Valid Data In TRHDX Data Hold After RD TRHDZ Data Float After RD 70 TLLDV ALE to Valid Data In 235 TAVDV Address to Valid Data In 260 TLLWL ALE to WR or RD 90 TAVWL Address to WR or RD 115 TQVWX Data Valid to WR Transition 20 TQVWH Data set-up to WR High 215 TWHQX Data Hold After WR 20 TRLAZ RD Low to Address Float TWHLH RD or WR High to ALE high 135 0 115 0 20 40 Figure 8. External Data Memory Write Cycle TWHLH TLLDV ALE PSEN TLLWL TRLDV TRLRH RD TLLAX PORT 0 TRHDX A0-A7 TAVWL PORT 2 TRHDZ TAVDV ADDRESS OR SFR-P2 DATA IN TRLAZ ADDRESS A8-A15 OR SFR P2 13 4149M–AERO–06/04 Figure 9. External Data Memory Read Cycle TWHLH ALE PSEN TLLWL TWLWH WR TQVWX TLLAX PORT 0 TWHQX TQVWH A0-A7 DATA OUT TAVWL PORT 2 ADDRESS OR SFR-P2 ADDRESS A8-A15 OR SFR P2 Table 6. Serial Port Timing – Shift Register Mode (ns) 30 MHz Symbol Parameter Min TXLXL Serial port clock cycle time 400 TQVHX Output data set-up to clock rising edge 300 TXHQX Output data hold after clock rising edge 50 TXHDX Input data hold after clock rising edge 0 TXHDV Clock rising edge to input data valid Max 300 Figure 10. Shift Register Timing Waveforms INSTRUCTION 0 1 2 3 4 5 6 7 8 ALE TXLXL CLOCK TXHQX TQVXH OUTPUT DATA WRITE to SBUF INPUT DATA CLEAR RI 14 0 1 2 3 4 5 6 7 TXHDX TXHDV VALID VALID VALID SET TI VALID VALID VALID VALID VALID SET RI 80C32E 4149M–AERO–06/04 80C32E Table 7. External Clock Drive Characteristics (XTAL1) Symbol Parameter Min TCLCL Oscillator Period 33.33 ns TCHCX High Time 5 ns TCLCX Low Time 5 ns TCLCH Rise Time 5 ns TCHCL Fall Time 5 ns Max Unit Figure 11. External Clock Drive Waveforms VCC-0.5 V 0.45 V 0.7VCC 0.2VCC-0.1V TCHCL TCHCX TCLCH TCLCX TCLCL Figure 12. AC Testing Input/Output Waveforms VCC-0.5V INPUT/OUTPUT 0.2V CC+0.9 0.2V CC-0.1 0.45V AC inputs during testing are driven at VCC - 0.5 for a logic “1” and 0.45V for a logic “0”. Timing measurement are made at VIH min for a logic “1” and VIL max for a logic “0”. Figure 13. Float Waveforms FLOAT VOH-0.1V VOL+0.1V VLOAD VLOAD+0.1V VLOAD-0.1V For timing purposes a port pin is no longer floating when a 100 mV change from load voltage occurs and begins to float when a 100 mV change from the loaded VOH/V OL level occurs. IOL/IOH ≥ ± 20 mA. 15 4149M–AERO–06/04 Figure 14. Clock Waveforms INTERNAL CLOCK STATE4 STATE5 STATE6 STATE1 STATE2 P1P2 P1P2 P1P2 P1P2 P1P2 STATE3 P1P2 STATE4 P1P2 STATE5 P1P2 XTAL2 ALE THESE SIGNALS ARE NOT ACTIVATED DURING THE EXECUTION OF A MOVX INSTRUCTION EXTERNAL PROGRAM MEMORY FETCH PSEN P0 DATA SAMPLED FLOAT P2 (EXT) PCL OUT DATA SAMPLED FLOAT PCL OUT DATA SAMPLED FLOAT PCL OUT INDICATES ADDRESS TRANSITIONS READ CYCLE RD PCL OUT (IF PROGRAM MEMORY IS EXTERNAL) P0 DPL OR Rt OUT FLOAT INDICATES DPH OR P2 SFR TO PCH TRANSITION P2 WRITE CYCLE WR P0 PCL OUT (EVEN IF MEMORY IS INTERNAL) DPL OR Rt OUT DATA OUT PCL OUT (IF PROGRAM MEMORY IS EXTERNAL) INDICATES DPH OR P2 SFR TO PCH TRANSITION P2 PORT OPERATION OLD DATA P0 PINS SAMPLED NEW DATA P0 PINS SAMPLED MOV DEST P0 MOV DEST PORT (P1, P2, (INCLUDES INT0, INT1, TO, T1) P1, P2, P3 PINS SAMPLED SERIAL PORT SHIFT CLOCK TXD (MODE 0) RXD SAMPLED P1, P2, P3 PINS SAMPLED RXD SAMPLED This diagram indicates when signals are clocked internally. The time it takes the signals to propagate to the pins, however, ranges from 25 to 125 ns. This propagation delay is dependent on variables such as temperature and pin loading. Propagation also varies from output to output and component. Typically though (TA=25°C fully loaded) RD and WR propagation delays are approximately 50 ns. The other signals are typically 85 ns. Propagation delays are incorporated in the AC specifications. 16 80C32E 4149M–AERO–06/04 80C32E Ordering Information Table 8. Possible Order Entries Speed (MHz) Temperature Range MC-80C32E-30-E 30 MJ-80C32E-30-E 30 MC-80C32E-30 30 -55°C to +125°C Side Brazed 40 pin (.6) Standard Mil. MJ-80C32E-30 30 -55°C to +125°C MQFPJ 44-pin Standard Mil. 5962-0051801QQC 30 -55°C to +125°C Side Brazed 40 pin (.6) QML-Q 5962-0051801QXC 30 -55°C to +125°C MQFPJ 44-pin QML-Q 5962-0051801VQC 30 -55°C to +125°C Side Brazed 40 pin (.6) QML-V 5962-0051801VXC 30 -55°C to +125°C MQFPJ 44-pin QML-V SCC9521002-01B 30 -55°C to +125°C Side Brazed 40 pin (.6) SCC B SCC9521002-02B 30 -55°C to +125°C MQFPJ 44-pin SCC B MM0-80C32E-30-E(1) 30 -55°C to +125°C Die Engineering samples 5962-0051801Q9A(1) 30 -55°C to +125°C Die QML-Q 5962-0051801V9A(1) 30 -55°C to +125°C Die QML-V Part Number Note: Package Quality Flow 25°C Side Brazed 40-pin (.6) Engineering samples 25°C MQFPJ 44-pin Engineering samples 1. Please contact Atmel for availability. 17 4149M–AERO–06/04 Package Drawings 40-pin Side Braze (600 mils) 18 80C32E 4149M–AERO–06/04 80C32E 44-pin Multilayer Quad Flat Pack 19 4149M–AERO–06/04 Atmel Headquarters Atmel Operations Corporate Headquarters Memory 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 487-2600 Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland TEL (41) 26-426-5555 FAX (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimhatsui East Kowloon Hong Kong TEL (852) 2721-9778 FAX (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan TEL (81) 3-3523-3551 FAX (81) 3-3523-7581 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 436-4314 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France TEL (33) 2-40-18-18-18 FAX (33) 2-40-18-19-60 ASIC/ASSP/Smart Cards Zone Industrielle 13106 Rousset Cedex, France TEL (33) 4-42-53-60-00 FAX (33) 4-42-53-60-01 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany TEL (49) 71-31-67-0 FAX (49) 71-31-67-2340 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL 1(719) 576-3300 FAX 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France TEL (33) 4-76-58-30-00 FAX (33) 4-76-58-34-80 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL 1(719) 576-3300 FAX 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland TEL (44) 1355-803-000 FAX (44) 1355-242-743 e-mail [email protected] Web Site http://www.atmel.com Disclaimer: Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life support devices or systems. © Atmel Corporation 2004. All rights reserved. ATMEL ® is a registered trademarks of Atmel. Other terms and product names may be the trademarks of others. Printed on recycled paper. 4149M–AERO–06/04 /xM