MN101C46F Type MN101C46F ROM (×× 8-bit) 96 K RAM (×× 8-bit) 3K Package (Conventional Package) SDIP042-P-0600C *Lead-free (SDIP042-P-0600) Minimum Instruction Execution Time Interrupts External (6 lines) Internal (12 lines) : Timer × 3, A/D, OSD, I 2C, Caption × 4, Remote control, Watchdog Timer Counter 8-bit timer × 3 Watchdog timer: system clock fs 1/216, 1/218, 1/220 triple selection Serial Interface I2C × 1: for multimaster mode, bus line (output) has 2 systems Caption • Built-in sync separator × 2 I/O Pins 1 279 ns (at 3.0 V to 3.6 V, 14.32 MHz) I/O 35 • Common use A/D Inputs 5-bit × 8-ch. (with S/H) PWM 8-bit × 6-ch. , 14-bit × 1-ch. Special Ports Remote control reception CRTC 1-layer display (graphics, characters) Notes Remote control input discriminant circuit built-in MAD00026CEM MN101C46F Pin Assignment ( IRQ0,RMIN,P00 1 42 VSS *1 SDA1,P01 2 41 OSC2 *1 SCL1,P02 3 40 OSC1 IRQ1,ADIN0,P03 4 39 VDD(VPP) *2 ADIN1,P04 5 38 P42,SCL0 *1 ADIN2,P05 6 37 P41,SDA0 *1 ADIN3,P06 7 36 P40,PWM ADIN4,P07 8 35 P37,NVSYNC,IRQ5 ADIN5,P10 9 34 P36,NRST ADIN6,P11 10 33 P35,YM ADIN7,P12 11 32 P34,ROUT *3 MMOD 12 31 P33,GOUT SYSCLK,P13 13 30 P32,BOUT *1 PWM0,P14 14 29 P31,YS PWM1,P15 15 28 FLASH *4 PWM2,P16 16 27 P30,NHSYNC IRQ2,PWM3,P17 17 26 P27,VREFH0 IRQ3,PWM4,P20 18 25 P26,CVBS0 *1 IRQ4,PWM5,P21 19 24 P25,CVBS1 VDD 20 23 P24,VREFH1 CLL,P22 21 22 P23,CLH MN101C46F SDIP042-P-0600C ) : Conventional Package *Lead-free (SDIP042-P-0600) *1: 5 V dielectric Nch open drain output pin *2: MN101C46F (VDD), MN101CF46F (VPP) *3: MMOD = H (fixed) (Set the test mode pin to the normal mode.) *4: FLASH = L (fixed) (Set the flash mode pin to the normal mode.) Support Tool In-circuit Emulator PX-ICE101C/D+PX-PRB101C46-SDIP042-P-0600-M EPROM Built-in Type Type MN101CF46F [ES (Engineering Sample) available] ROM (× 8-bit) 96 K RAM (× 8-bit) 3K Minimum instruction execution time 279 ns (at 3.0 V to 3.6 V, 14.32 MHz) Package SDIP042-P-0600C *Lead-free (Conventional Package) MAD00026CEM (SDIP042-P-0600) 2 Request for your special attention and precautions in using the technical information and semiconductors described in this material (1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technologies described in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. (2) The technical information described in this material is limited to showing representative characteristics and applied circuits examples of the products. It neither warrants non-infringement of intellectual property right or any other rights owned by our company or a third party, nor grants any license. (3) We are not liable for the infringement of rights owned by a third party arising out of the use of the product or technologies as described in this material. (4) The products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: • Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. • Any applications other than the standard applications intended. (5) The products and product specifications described in this material are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (6) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage, and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (7) When using products for which damp-proof packing is required, observe the conditions (including shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets are individually exchanged. (8) This material may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita Electric Industrial Co., Ltd. 2002 JUL