PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note C02E.pdf 05.12.14 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Chip Monolithic Ceramic Capacitors Low ESL LLL/LLA/LLM Series W L T ■ Features (Reversed geometry Low ESL Type) 1. Low ESL, good for noise reduction for high frequency 2. Small, high cap ■ Applications Part Number 1. High speed micro processor 2. High frequency digital equipment LLL185 LLL216 LLL219 LLL317 LLL31M L 1.6 ±0.1 Dimensions (mm) W 0.8 ±0.1 2.0 ±0.1 1.25 ±0.1 3.2 ±0.15 1.6 ±0.15 T 0.6 max. 0.6 ±0.1 0.85 ±0.1 0.7 ±0.1 1.15 ±0.1 Reversed geometry Low ESL Type LLL18 Part Number LLL21 1.6x0.8 LxW 2.0x1.25 X7R (R7) TC Rated Volt. 50 (1H) 25 (1E) 16 (1C) X7S (C7) 10 (1A) LLL31 6.3 (0J) 4 (0G) 3.2x1.6 X7R (R7) 50 (1H) 25 (1E) 16 (1C) X7S (C7) 10 (1A) 6.3 (0J) 4 (0G) X7R (R7) 50 (1H) 25 (1E) 16 (1C) X5R (R6) 10 (1A) 6.3 (0J) 6.3 (0J) Capacitance (Capacitance part numbering code) and T (mm) Dimension (T Dimension part numbering code) 12 2200pF (222) 0.5 (5) 3300pF (332) 0.5 (5) 4700pF (472) 0.5 (5) 0.6 (6) 6800pF (682) 0.5 (5) 10000pF (103) 0.5 (5) 0.5 (5) 0.6 (6) 0.7 (7) 15000pF (153) 0.5 (5) 0.5 (5) 0.6 (6) 0.7 (7) 0.7 (7) 22000pF (223) 0.5 (5) 0.5 (5) 0.6 (6) 0.6 (6) 0.7 (7) 0.7 (7) 33000pF (333) 0.5 (5) 0.85 (9) 0.6 (6) 0.6 (6) 0.7 (7) 0.7 (7) 47000pF (473) 0.5 (5) 0.6 (6) 0.6 (6) 0.7 (7) 0.7 (7) 68000pF (683) 0.5 (5) 0.6 (6) 0.6 (6) 0.7 (7) 0.7 (7) 0.6 (6) 0.6 (6) 1.15 (M) 0.7 (7) 0.85 (9) 0.6 (6) 1.15 (M) 0.7 (7) 0.10µF (104) 0.6 (6) 0.5 (5) 0.15µF (154) 0.5 (5) 0.22µF (224) 0.5 (5) 0.6 (6) 1.15 (M) 0.33µF (334) 0.5 (5) 0.6 (6) 1.15 (M) 0.7 (7) 0.47µF (474) 0.5 (5) 0.85 (9) 1.15 (M) 0.7 (7) Continued on the following page. 64 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note C02E.pdf 05.12.14 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Continued from the preceding page. LLL18 Part Number LLL21 1.6x0.8 LxW 2.0x1.25 X7R (R7) TC Rated Volt. 50 (1H) 25 (1E) X7S (C7) 16 (1C) 10 (1A) LLL31 6.3 (0J) 4 (0G) 3.2x1.6 X7R (R7) 50 (1H) 25 (1E) 16 (1C) X7S (C7) 10 (1A) 6.3 (0J) 4 (0G) X7R (R7) 50 (1H) 25 (1E) X5R (R6) 16 (1C) 10 (1A) 0.85 (9) 1.15 (M) 0.7 (7) 0.85 (9) 1.15 (M) 0.7 (7) 6.3 (0J) 6.3 (0J) Capacitance (Capacitance part numbering code) and T (mm) Dimension (T Dimension part numbering code) 0.68µF (684) 1.0µF (105) 0.5 (5) 1.5µF (155) 0.85 (9) 2.2µF (225) 0.85 (9) 1.15 (M) 0.7 (7) 1.15 (M) 0.7 (7) 4.7µF (475) 1.15 (M) 10µF (106) 1.25 (B) The part numbering code is shown in ( ). Dimensions are shown in mm and Rated Voltage in Vdc. Reversed geometry Low ESL Type Low Profile Part Number LLL18 LLL21 LLL31 LxW 1.6x0.8 2.0x1.25 3.2x1.6 X7R (R7) TC Rated Volt. 25 (1E) 16 (1C) X7S (C7) 10 (1A) 4 (0G) X7R (R7) 50 (1H) 25 (1E) 16 (1C) X7S (C7) 10 (1A) 6.3 (0J) 4 (0G) X7R (R7) 50 (1H) 25 (1E) 16 (1C) 12 10 (1A) Capacitance (Capacitance part numbering code) and T (mm) Dimension (T Dimension part numbering code) 680pF(681) 0.5(5) 1000pF(102) 0.5(5) 1500pF(152) 0.5(5) 2200pF(222) 0.5(5) 3300pF(332) 0.5(5) 4700pF(472) 0.5(5) 6800pF(682) 0.5(5) 10000pF(103) 0.5(5) 0.5(5) 0.5(5) 0.5(5) 15000pF(153) 0.5(5) 0.5(5) 0.5(5) 0.5(5) 0.5(5) 0.5(5) 0.5(5) 22000pF(223) 0.5(5) 0.5(5) 0.5(5) 0.5(5) 0.5(5) 33000pF(333) 0.5(5) 0.5(5) 0.5(5) 0.5(5) 0.5(5) 47000pF(473) 0.5(5) 0.5(5) 0.5(5) 0.5(5) 68000pF(683) 0.5(5) 0.5(5) 0.5(5) 0.5(5) 0.10µF(104) 0.5(5) 0.5(5) 0.5(5) 0.5(5) 0.15µF(154) 0.5(5) 0.5(5) 0.5(5) 0.22µF(224) 0.5(5) 0.5(5) 0.33µF(334) 0.5(5) 0.5(5) 0.47µF(474) 0.5(5) 0.5(5) 0.5(5) 0.68µF(684) 1.0µF(105) 0.5(5) 0.5(5) The part numbering code is shown in ( ). Dimensions are shown in mm and Rated Voltage in Vdc. 65 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note C02E.pdf 05.12.14 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. W T L ■ Features (Eight Terminals Low ESL Type) 1. Low ESL (100pH) , suitable to decoupling capacitor for 1GHz clock speed IC. 2. Small, large cap q w e Equivalent Circuit r q e t u w r y i P i ■ APPLICATIONS Part Number 1. High speed micro processor 2. High frequency digital equipment. LLA185 LLA215 LLA219 LLA315 LLA319 LLA31M L 1.6 ±0.1 2.0 ±0.1 2.0 ±0.1 3.2 ±0.15 3.2 ±0.15 3.2 ±0.15 u y t Dimensions (mm) W T 0.8 ±0.1 0.5 +0.05/-0.1 1.25 ±0.1 0.5 +0.05/-0.1 1.25 ±0.1 0.85 ±0.1 1.6 ±0.15 0.5 +0.05/-0.1 1.6 ±0.15 0.85 ±0.1 1.6 ±0.15 1.15±0.1 P 0.4 ±0.1 0.5 ±0.05 0.5 ±0.05 0.8 ±0.1 0.8 ±0.1 0.8 ±0.1 Eight Terminals Low ESL Type Part Number LLA18 LLA21 LLA31 LxW 1.6x0.8 2.0x1.25 3.2x1.6 TC X7S (C7) Rated Volt. 4 (0G) X7R (R7) 25 (1E) 16 (1C) X7S (C7) 10 (1A) 6.3 (0J) X7R (R7) 4 (0G) 16 (1C) 10 (1A) 4 (0G) Capacitance (Capacitance part numbering code) and T (mm) Dimension (T Dimension part numbering code) 10000pF(103) 0.85(9) 15000pF(153) 0.85(9) 22000pF(223) 0.85(9) 33000pF(333) 0.85(9) 47000pF(473) 0.85(9) 68000pF(683) 0.85(9) 0.10µF(104) 0.85(9) 0.85(9) 0.15µF(154) 0.85(9) 1.15(M) 12 0.22µF(224) 0.85(9) 0.85(9) 0.33µF(334) 0.5(5) 0.85(9) 0.85(9) 0.47µF(474) 0.5(5) 0.85(9) 0.85(9) 0.68µF(684) 1.0µF(105) 0.85(9) 0.85(9) 0.5(5) 0.85(9) 1.5µF(155) 0.85(9) 0.85(9) 0.85(9) 2.2µF(225) 0.85(9) 4.7µF(475) 0.85(9) 0.85(9) The part numbering code is shown in ( ). Dimensions are shown in mm and Rated Voltage in Vdc. Eight Terminals Low ESL Type Low Profile Part Number LxW LLA21 LLA31 2.0x1.25 3.2x1.6 X7R (R7) TC Rated Volt. 25 (1E) 16 (1C) X7S (C7) 10 (1A) 6.3 (0J) 4 (0G) X7R (R7) 16 (1C) 10 (1A) 6.3 (0J) Capacitance (Capacitance part numbering code) and T (mm) Dimension (T Dimension part numbering code) 10000pF(103) 0.5(5) 15000pF(153) 0.5(5) 22000pF(223) 0.5(5) 33000pF(333) 0.5(5) 47000pF(473) 0.5(5) 68000pF(683) 0.5(5) 0.10µF(104) 0.5(5) 0.5(5) 0.15µF(154) 0.5(5) 0.5(5) 0.5(5) 0.22µF(224) 0.5(5) 0.5(5) 0.5(5) Continued on the following page. 66 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note C02E.pdf 05.12.14 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Continued from the preceding page. LLA21 Part Number LLA31 2.0x1.25 LxW 3.2x1.6 X7R (R7) TC Rated Volt. 25 (1E) 16 (1C) X7S (C7) 10 (1A) 6.3 (0J) 4 (0G) X7R (R7) 16 (1C) 10 (1A) 6.3 (0J) Capacitance (Capacitance part numbering code) and T (mm) Dimension (T Dimension part numbering code) 0.33µF(334) 0.5(5) 0.5(5) 0.47µF(474) 0.5(5) 0.5(5) 0.5(5) 0.68µF(684) 0.5(5) 0.5(5) 1.0µF(105) 0.5(5) 0.5(5) 1.5µF(155) 0.5(5) 0.5(5) 2.2µF(225) 0.5(5) 0.5(5) The part numbering code is shown in ( ). Dimensions are shown in mm and Rated Voltage in Vdc. 12 67 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note C02E.pdf 05.12.14 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. W L T ■ Features (Ten Terminals Low ESL Type) 1. Low ESL (45pH), suitable to decoupling capacitor for 2GHz clock speed IC. 2. Small, large cap q w e Equivalent Circuit r q e t u o P !0 o ■ APPLICATIONS Part Number 1. High speed micro processor 2. High frequency digital equipment LLM215 LLM219 LLM315 LLM31M L 2.0 ±0.1 2.0 ±0.1 3.2 ±0.15 3.2 ±0.15 i u t y Dimensions (mm) W T 1.25 ±0.1 0.5 +0.05/-0.1 1.25 ±0.1 0.85 ±0.1 1.6 ±0.15 0.5 +0.05/-0.1 1.6 ±0.15 1.15±0.1 w r y i !0 P 0.5 ±0.05 0.5 ±0.05 0.8 ±0.1 0.8 ±0.1 Ten Terminals Low ESL Type Part Number LxW LLM21 LLM31 2.0x1.25 3.2x1.6 X7R (R7) TC Rated Volt. 25 (1E) X7S (C7) 16 (1C) 6.3 (0J) 4 (0G) X7R (R7) 16 (1C) 10 (1A) 6.3 (0J) Capacitance (Capacitance part numbering code) and T (mm) Dimension (T Dimension part numbering code) 10000pF(103) 0.85(9) 15000pF(153) 0.85(9) 22000pF(223) 0.85(9) 33000pF(333) 0.85(9) 47000pF(473) 0.85(9) 68000pF(683) 0.85(9) 0.10µF(104) 0.85(9) 1.15(M) 0.15µF(154) 0.85(9) 1.15(M) 0.22µF(224) 0.85(9) 12 1.15(M) 0.33µF(334) 0.85(9) 1.15(M) 0.47µF(474) 0.85(9) 1.15(M) 0.68µF(684) 0.85(9) 1.15(M) 1.0µF(105) 0.85(9) 1.15(M) 1.5µF(155) 0.85(9) 2.2µF(225) 1.15(M) 0.85(9) 1.15(M) 3.3µF(335) 1.15(M) 4.7µF(475) 1.15(M) The part numbering code is shown in ( ). Dimensions are shown in mm and Rated Voltage in Vdc. Ten Terminals Low ESL Type Low Profile Part Number LxW LLM21 LLM31 2.0x1.25 3.2x1.6 X7R (R7) TC Rated Volt. 25 (1E) 16 (1C) X7S (C7) 6.3 (0J) 4 (0G) X7R (R7) 16 (1C) 10 (1A) 6.3 (0J) Capacitance (Capacitance part numbering code) and T (mm) Dimension (T Dimension part numbering code) 10000pF(103) 0.5(5) 15000pF(153) 0.5(5) 22000pF(223) 0.5(5) 33000pF(333) 0.5(5) 47000pF(473) 0.5(5) 68000pF(683) 0.5(5) 0.10µF(104) 0.5(5) 0.15µF(154) 0.5(5) 0.5(5) 0.5(5) Continued on the following page. 68 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note C02E.pdf 05.12.14 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Continued from the preceding page. LLM21 Part Number LLM31 2.0x1.25 LxW 3.2x1.6 X7R (R7) TC Rated Volt. 25 (1E) 16 (1C) X7S (C7) 6.3 (0J) 4 (0G) X7R (R7) 16 (1C) 10 (1A) 6.3 (0J) Capacitance (Capacitance part numbering code) and T (mm) Dimension (T Dimension part numbering code) 0.22µF(224) 0.5(5) 0.33µF(334) 0.5(5) 0.5(5) 0.5(5) 0.47µF(474) 0.5(5) 0.5(5) 0.68µF(684) 0.5(5) 0.5(5) 1.0µF(105) 0.5(5) 1.5µF(155) 0.5(5) 2.2µF(225) 0.5(5) 0.5(5) The part numbering code is shown in ( ). Dimensions are shown in mm and Rated Voltage in Vdc. 12 69 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note C02E.pdf 05.12.14 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Specifications and Test Methods No. 1 Specifications Item Operating Temperature Range Test Method R6 : Y55 to W85°C R7, C7 : Y55 to W125°C 2 Rated Voltage See the previous pages. The rated voltage is defined as the maximum voltage which may be applied continuously to the capacitor. When AC voltage is superimposed on DC voltage, VP-P or VO-P, whichever is larger, should be maintained within the rated voltage range. 3 Appearance No defects or abnormalities Visual inspection 4 Dimensions Within the specified dimension Using calipers 5 Dielectric Strength No defects or abnormalities No failure should be observed when 250% of the rated voltage is applied between the terminations for 1 to 5 seconds, provided the charge/discharge current is less than 50mA. 6 Insulation Resistance More than 10,000MΩ or 500Ω · F (Whichever is smaller) The insulation resistance should be measured with a DC voltage not exceeding the rated voltage at 25°C and 75%RH max. and within 2 minutes of charging. 7 Capacitance Within the specified tolerance 8 Dissipation Factor (D.F.) W.V.: 25V min.; 0.025 max. W.V.: 16V max.; 0.035 max. *1 The capacitance/D.F. should be measured at 25°C at the frequency and voltage shown in the table. Capacitance CV10µF (10V min.) CV10µF (6.3V max.) C>10µF Frequency 1T0.1kHz 1T0.1kHz 120T24kHz Voltage 1.0T0.2Vrms 0.5T0.1Vrms 0.5T0.1Vrms The capacitance change should be measured after 5 min. at each specified temperature stage. 9 12 Capacitance Temperature Characteristics Char. R6 R7 C7 Temp. Range (°C) Y55 to +85 Y55 to +125 Y55 to +125 Reference Temp. 25°C 25°C 25°C Cap.Change Within T15% Within T15% Within T22% Step 1 2 3 4 5 Temperature (°C) 25T2 Y55T3 25T2 125T3 25T2 The ranges of capacitance change compared with the 25°C value over the temperature ranges shown in the table should be within the specified ranges. 10 11 12 Adhesive Strength of Termination Appearance No defects or abnormalities Capacitance Within the specified tolerance D.F. W.V.: 25V min.; 0.025 max. W.V.: 16V max.; 0.035 max. *1 Vibration Resistance Solderability of Termination Resistance 13 to Soldering Heat No removal of the terminations or other defect should occur. 75% of the terminations are to be soldered evenly and continuously. Appearance No marking defects Capacitance Change Within T7.5% D.F. W.V.: 25V min.; 0.025 max. W.V.: 16V max.; 0.035 max. *1 I.R. More than 10,000MΩ or 500Ω · F (Whichever is smaller) Dielectric Strength No failure Solder the capacitor to the test jig (glass epoxy board) using a eutectic solder. Then apply 5N force in parallel with the test jig for 10T1 sec. The soldering should be done either with an iron or using the reflow method and should be conducted with care so that the soldering is uniform and free of defects such as heat shock. Solder the capacitor to the test jig (glass epoxy board) in the same manner and under the same conditions as (10). The capacitor should be subjected to a simple harmonic motion having a total amplitude of 1.5mm, the frequency being varied uniformly between the approximate limits of 10 and 55Hz. The frequency range, from 10 to 55Hz and return to 10Hz, should be traversed in approximately 1 minute. This motion should be applied for a period of 2 hours in each 3 mutually perpendicular directions (total of 6 hours). Immerse the capacitor in a solution of ethanol (JIS-K-8101) and rosin (JIS-K-5902) (25% rosin in weight proportion). Preheat at 80 to 120°C for 10 to 30 seconds. After preheating, immerse in eutectic solder solution for 2T0.5 seconds at 230T5°C, or Sn-3.0Ag-0.5Cu solder solution for 2T0.5 seconds at 245T5°C. Preheat the capacitor at 120 to 150°C for 1 minute. Immerse the capacitor in a eutectic solder or Sn-3.0Ag-0.5Cu solder solution at 270T5°C for 10T0.5 seconds solution at 270T5°C for 10T0.5 seconds. Let sit at room temperature for 48T4 hours, then measure. • Initial measurement. Perform a heat treatment at 150 +0 –10 °C for one hour and then let sit for 48T4 hours at room temperature. Perform the initial measurement. Continued on the following page. 70 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it’s specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our • Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note • This !Note C02E.pdf 05.12.14 sales representatives or product engineers before ordering. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Specifications and Test Methods Continued from the preceding page. No. 14 Specifications Item Temperature Cycle Appearance No marking defects Capacitance Change Within T7.5% *1 D.F. W.V.: 25V min.; 0.025 max. W.V.: 16V max.; 0.035 max. *1 I.R. More than 10,000MΩ or 500Ω · F (Whichever is smaller) Test Method Fix the capacitor to the supporting jig in the same manner and under the same conditions as (10). Perform the five cycles according to the four heat treatments listed in the following table. Let sit for 48T4 hours at room temperature, then measure. Step 1 2 3 4 Min. Operating Room Max. Operating Room +3 Temp. (°C) Temp. +0 –3 Temp. –0 Temp. Temp. Time (min.) 15 16 17 Humidity (Steady State) Humidity Load High Temperature Load Dielectric Strength No failure Appearance No marking defects Capacitance Change Within T12.5% *1 D.F. 0.05 max. *1 I.R. More than 1,000MΩ or 50Ω · F (Whichever is smaller) Appearance No marking defects Capacitance Change Within T12.5% *1 D.F. 0.05 max. *1 I.R. More than 500MΩ or 25Ω · F *1 (Whichever is smaller) Dielectric Strength No failure Appearance No marking defects Capacitance Change Within T12.5% *1 D.F. W.V.: 25V min.; 0.04 max. W.V.: 16V max.; 0.05 max. *1 I.R. More than 1,000MΩ or 50Ω · F *1 (Whichever is smaller) Dielectric Strength No failure 30T3 2 to 3 30T3 2 to 3 • Initial measurement. Perform a heat treatment at 150 +0 –10 °C for one hour and then let sit for 48T4 hours at room temperature. Perform the initial measurement. Sit the capacitor at 40T2°C and 90 to 95% humidity for 500T12 hours. Remove and let sit for 48T4 hours at room temperature, then measure. Apply the rated voltage at 40T2°C and 90 to 95% humidity for 500T12 hours. Remove and let sit for 48T4 hours at room temperature, then measure. The charge/discharge current is less than 50mA. Apply 200% of the rated voltage for 1000T12 hours at the maximum operating temperature T3°C. Let sit for 48T4 hours at room temperature, then measure. The charge/discharge current is less than 50mA. 12 •Initial measurement. Apply 200% (*2) of the rated DC voltage for one hour at the maximum operating temperature T3°C. Remove and let sit for 48T4 hours at room temperature. Perform initial measurement. (*1) *1 : The ligure Indicates typical inspection.Please refer to individual specifications. *2 : Some of the parts are applicable in rated voltageA150%. Please refer to individual specifications. 71